PLI-3510 - Powerline Adapter LEVELONE - Free user manual and instructions

USER MANUAL PLI-3510 LEVELONE

level® one

LevelOne

PLI-3510

200Mbps Powerline Adapter with Mains Pass-Through

User Manual

Table of Contents

Chapter 1 – Introduction ...... 1

1.1 Overview.... 1
1.2 Specification .... 1
1.3 LED Indicators.... 1
1.4 Package Contents.... 1
1.5 System Requirements.... 1

Chapter 2 – Installation & Uninstallation.... 2

2.1 Installing Powerline Device.... 2
2.2 Installation of Powerline Utility.... 3
2.3 Uninstallation of Configuration Utility....7
3.1 Main Tab....8
3.2 Privacy Screen 14
3.3 Diagnostics Screen.... 15
3.4 About Screen.... 16

Chapter 4 – Reset and Network ID Buttons Setting ...... 17

4.1 Reset Button.... 17
4.2 Network ID Button 17

Chapter 1 – Introduction

1.1 Overview

The LevelOne PLI-3510 operates on HomePlug AV standard, providing up to 200Mbps data speed over the existing household power supply. This Product is cost-effective, easy to create a home network without spending time and money to run expensive CAT5 cabling. Powerline Device is the best solution for no-new-wire networking in the house or office.

1.2 Specification

• Standard: IEEE 1901 Broadband over Powerl / HomePlug Powerline Specification AV compliant
• Speed: up to 200Mbps
• Modulation: supports OFDM, 1024/256/64/16/8 QAM, QPSK, BPSK, and ROBO modulation schemes.
• Frequency: 4.3 MHz \~ 20.9 MHz
• Security: 128-bits AES encryption
• IEEE802.3 10Base-T, IEEE802.3U 100Base-TX

1.3 LED Indicators

The Powerline Ethernet Adaptor has three LEDs indicator:

PWR	Turn on when connected to AC power supply.
PLC	Turn on when detected and connected with another HomePlug adaptor within the network.
ETH	Turn on when connected to the Ethernet card of the computer or Ethernet Hub / Switch.

1.4 Package Contents

Make sure that you have the following items:

• PLI-3510 200Mbps Powerline Adapter with Mains Pass-Through
• RJ-45 cable
• CD User Manual / Utility / QIG
• Quick Installation Guide

1.5 System Requirements

• Powerline Ethernet Adaptor can support any Operation System. But the Powerline Utility can only support Windows 2000/XP/Vista/Windows 7.
• Pentium III 300 MHz or above
• Powerline device
• AC power outlet

Chapter 2 – Installation & Uninstallation

Connection of Powerline Ethernet Adapter

Ethernet Cable (RJ-45) Powerline

graph LR
    A["Notebook"] --> B["PC"]
    B --> C["Room 1"]
    C --> D["PC"]
    D --> E["Room 2"]
    E --> F["ADSL / Cable Modem"]
    F --> G["Internet"]
    style C fill:#f9f,stroke:#333
    style E fill:#f9f,stroke:#333
    style G fill:#bbf,stroke:#333

2.1 Installing Powerline Device

1. If you have the SINGLE PACKAGE of Powerline, Connect the supplied RJ45 Ethernet cable from your PC's Ethernet port to the Powerline Ethernet Adapter's LAN Ports or connect the supplied RJ45 Ethernet cable from your xDSL/Cable Modem's Ethernet port to the Powerline Ethernet Adapter's LAN Ports.
2. If you have the TWIN PACKAGE of Powerline, connect the supplied RJ45 Ethernet cable from your PC's Ethernet port to the Powerline Ethernet Adapter's LAN Ports and connect the supplied RJ45 Ethernet cable from your xDSL/Cable Modem's Ethernet port to the Powerline Ethernet Adapter's LAN Ports.
3. Connect the Powerline Ethernet Adapter to your wall-mounted power outlet.
4. Check if the PLC LED of Powerline Ethernet Adapter is ON, the Powerline Ethernet Adapter is connected and suitable for Internet Connections.
5. Check if the PLC LED is OFF, the Powerline Ethernet Adapter isn't connected and suitable for Internet Connections. Please follow next step to have it connected and suitable for Internet Connections.

2.2 Installation of Powerline Utility

The Configuration Utility enables the users to identify HomePlug devices on the Powerline network; measures data rate performance, ensures privacy and performs diagnostics by setting user defined secure Powerline networks.

Users are requested to verify that no other Encryption Management Utilities are installed prior to the installation of this utility. Other utilities should be uninstalled before installing this utility.

1. In order to install, insert Configuration Utility CD-ROM into the computer's CD-ROM drive. The program shall run automatically. Alternatively this can also be done manually by double clicking the autorun.exe file on the CD.
2. For Windows 7 / Vista User only, for Security reasons Windows 7 / Vista requires the installer program to have administrator privileges so the new policy called "User Account Control" has been introduced in Windows 7 / Vista. If UAC is enabled Windows pops up a window "User Account Control" Windows need your permission to continue. User needs to click "Yes / Allow" to continue.
3. Please click "Utility" button to continue.

LevelOne PLI-3510 level® one PLI-3510 200Mbps Powerline Adapter with Mains Pass-Through Quick Guide User Manual Utility Install Adobe Reader Explore the CD Exit level® one one world_one brand_one level

4. Click "Setup" button to continue.

WinZip Self-Extractor - Level One Power Packet Utility.exe Level One Power Packet Utility Setup Cancel About

5. Click "Next" button to continue.

C:\Windows\system32\cmd.exe Power Packet Utility (PPU) Installation is in progress... nsyString - "VinPcap Software (version 4.1.2) is either not installed or some previous version is already installed on this workstation. The VinPcap (ve version 4.1.2) installer is being launched. Please follow the instructions for in talling the VinPcap software? >) InstallWinPcap.obs Power Packet Utility Welcome to the Power Packet Utility Setup Wizard The install will guide you through the steps required to install Power Packet Utility on your computer. WARNING: This computer program is protected by copyright law and international treaties. Unauthorized duplication or distribution of this program, or any portion of it, may result in severe civil or criminal penalties, and will be prosecuted to the maximum extent possible under the law. Cancel < Back Next >

6. Click "I Agree & Next" button to continue.

Power Packet Utility License Agreement Please take a moment to read the license agreement now. If you accept the terms below, click "I Agree", then "Next". Otherwise click "Cancel". Atheros Communications, Inc. Software License Agreement PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("LICENSE") CAREFULLY BEFORE USING THE Atheros SOFTWARE. BY USING THE Atheros SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. IF YOU DO NOT AGREE TO THE TERMS OF THIS LICENSE, DO NOT USE THE SOFTWARE. IF YOU DO NOT AGREE TO THE TERMS OF THE LICENSE, YOU MAY RETURN THE Atheros SOFTWARE TO THE PLACE WHERE YOU ○ I Do Not Agree ● I Agree Cancel < Back Next >

1. Click "Next" button to continue.

Power Packet Utility Confirm Installation The installer is ready to install Power Packet Utility on your computer. Click "Next" to start the installation. Cancel < Back Next >

1. Click "Close" button to exit.

Power Packet Utility Installation Complete Power Packet Utility has been successfully installed. Click "Close" to exit. Cancel < Back Close

1. In order to start the utility, double-click the utility icon on desktop.

1. You can see your device working well. The top panel of the screen shot shows a Homeplug device connected locally to your computer. The bottom panel shows one device connected remotely to the computer running the utility.

Power Packet Utility Main | Privacy | Diagnostics | About | Local Device(s) on your computer: Device Type MAC Address HomePlug AV 6x00 D... 00:13:33:94:A3:90 Connected to HomePlug AV 6x00 Device Connect Upgrade Firmware 1 Powerline Device detected: Network Type: Public Autoscan On Device Name Password Quality Rate (Mbps) MAC Address Device 2 188.00 00:13:33:94:A3:94 levelone* Rename Enter Password Add Scan Close

2.3 Uninstallation of Configuration Utility

1. To uninstall the Configuration Utility, go to the "Control Panel" of your system.
2. Open the "Add/Remove Programs".
3. Select and double click on the "Powerline Utility" in the Add/Remove Programs Properties.

Add or Remove Programs Currently installed programs: Show updates Sort by: Name NetIQ Chariot Size 24.78MB NetIQ Endpoint Size 5.32MB Network Stumbler 0.4.0 (remove only) Size 0.74MB Norton Ghost Size 440.00MB NVIDIA Windows 2000/XP Display Drivers Power Packet Utility Size 2.01MB Click here for support information. Used occasionally Last Used On 4/29/2011 To change this program or remove it from your computer, click Change or Remove. Change Remove PowerISO Size 2.26MB Snagit 9.1 Size 143.00MB SolidWorks 2007 SP0 Size 1,751.00MB SolidWorks Explorer 2007 sp0 Size 87.62MB SolidWorks Installation Manager Size 3.25MB SoundMAX Size 12.60MB Spelling Dictionaries Support For Adobe Reader 9 Size 29.69MB TeamViewer 4 Size 4.83MB VIA Integrated Setup Wizard

1. Follow the on screen instructions to uninstall the Powerline Utility.

Chapter 3 – Configuration Utility Setup

Introduction

The Configuration Utility enables the users to identify HomePlug devices on the powerline network, measures data rate performance, ensures privacy and performs diagnostics by setting user defined secure powerline networks.

The Utility will use a Graphical User Interface (GUI) with limited user selectable options.

3.1 Main Tab

In order to start the utility, double-click the utility icon Utility on desktop. Figure 3-1 shows the main screen of the Configuration Utility. The top panel of the screen shot shows a HomePlug AV device connected locally to the host computer. The bottom panel shows four devices connected remotely to the computer running the utility.

Power Packet Utility Main | Privacy | Diagnostics | About | Local Device(s) on your computer: Device Type MAC Address HomePlug AV 6x00 D... 00:13:33:94:A3:90 Connected to HomePlug AV 6x00 Device Connect Upgrade Firmware 0 Powerline Devices detected: Network Type: Public Autoscan On Device Name Password Quality Rate (Mbps) MAC Address levelone Rename Enter Password Add Scan Close

Figure 3-1: Main Screen with HomePlug AV device Local

The Main screen provides a list of all powerline devices logically connected to the computer when the utility is running. The top panel shows all local HomePlug devices connected to the computer's NIC (Network Interface Card). In most cases, only one device will be seen. In situations where there are more than one local device being connected, such as a USB or an Ethernet adapter, the user can select the local device by clicking on it and then click the Connect button to its right. The status area above the button indicates that your PC is connected to that same device. Once connected to the local device, the utility will automatically scan the power line periodically for any other HomePlug devices. If no local HomePlug devices are discovered, the status area above the connect button will indicate with a message 'NO HOMEPLUG ADAPTERS DETECTED'.

Figure 3-2 illustrates the presence of two local devices connected locally to the computer.

Power Packet Utility Main | Privacy | Diagnostics | About | Local Device(s) on your computer: Device Type MAC Address HomePlug AV 6x00 D... 00:13:33:94:A3:90 Connected to HomePlug AV 6x00 Device Connect Upgrade Firmware 1 Powerline Device detected: Network Type: Public Autoscan On Device Name Password Quality Rate (Mbps) MAC Address Device 2 188.00 00:13:33:94:A3:94 levelone* Rename Enter Password Add Scan Close

Figure 3-2: Multiple Local Device Connection

The lower panel displays all the HomePlug remote devices, discovered on the current logical network. The total number of remote devices connected on the same network can be found on top of the Remote device panel. The Network type (Public or Private) is also displayed based on the network status of the local device. The scan status option is displayed on the top right corner

above the Remote devices panel showing whether the Autoscan functionality is turned ON or OFF. The following information is displayed for all devices that appear in the lower panel.

Device Name column shows the default device name, which may be user re-defined. A user can change the name by either using the rename button or by clicking on the name and editing in-place. An icon is usually shown with the name. By default, the icon is always accompanied by a device name.

MAC Address column shows the Remote device's MAC address.

Password column by default is blank and 'Enter Password' button can be used to enter it. To set the Password of the device (required when creating a private network), first select the device by clicking on its name in the lower panel and then click on the Enter Password button. A dialog box will appear as shown in Figure 3-3 to type the password. The selected device name is shown above the password field and the password can be verified by hitting the OK button. The Password field accepts the Device password in any case formats, with or without dashed between them. If a device was not found, the user will be notified along with the suggestions to resolve common problems. This process might take a few seconds to get completed.

Set Device Password Device: Device 2 (00:13:33:94:A3:94) Password: The Password typically appears as a number and letter code, in groups of four, separated by dashes. (jie XK8Y-GH26-BR1K-LZSA) It is found on the device or packaging. OK Cancel

Figure 3-3: Set Device Password

Add button is used to add a remote device to the existing network by entering the device password of the device. A dialog box will appear as shown below in Figure 3-4. The dialog box allows the user to enter both a device name and the password. If a device was not found, the user will be notified and suggestions to resolve common problems will be presented.

Set Device Password Device: Device 2 (00:13:33:94:A3:94) Password: PASS-WORD-DOES-HERE The Password typically appears as a number and letter code, in groups of four, separated by dashes. (jie XK8Y-GH26-BR1K-LZSA) It is found on the device or packaging. OK Cancel

Figure 3-4: Add Remote Device

Note: The device must be present on the power line (plugged in) in order for the password to be confirmed and added to the network. If the device could not be located, a warning message will be shown.

The Scan button is used to perform an immediate search of the HomePlug devices connected to the Powerline network. By default, the utility automatically scans every few seconds and updates the display screen.

A typical screen after naming and supplying passwords might appear as in Figure 3-5.

Power Packet Utility Main | Privacy | Diagnostics | About | Local Device(s) on your computer: Device Type MAC Address HomePlug AV 6x00 D... 00:13:33:94:A3:90 Connected to HomePlug AV 6x00 Device Connect Upgrade Firmware 1 Powerline Device detected: Network Type: Public Scanning... Device Name Password Quality Rate (Mbps) MAC Address Device 2 188.00 00:13:33:94:A3:94 levelone* Rename Enter Password Add Scan Close

Figure 3-5: Main Screen of the Configuration Utility

3.2 Privacy Screen

The Privacy screen provides the user with an option to maintain security for their logical network and also to select the devices that has to be included in the network. The appearance is shown in Figure 3-6. All HomePlug devices are shipped using a default logical network (network name), which is normally “HomePlugAV”. The Privacy dialog screen allows user to change to a private network by changing the network name (network password) of devices.

The user can always reset to the HomePlug network (Public) by entering "HomePlugAV" as the network name or by clicking on the "Use Default" button.

Note: Changing the network name to anything other than HomePlugAV will show the network type on the main screen as Private.

Power Packet Utility Main Privacy Diagnostics About Use this screen to create a Private Network that provides you with extra security. Private Network Name HomePlug OR Use Default (Public Network) Do not share the network name with others you do not want to be part of this network. After setting the name above, choose how it will be applied below. Place On This Network Only the device attached to this computer (the Local Device). (Isolates this computer from others): Set Local Device Only ALL devices whose Password has been entered. (They communicate together but are isolated from devices with a different network name) OR Set All Devices Close

Figure 3-6: Privacy Screen

The Set Local Device Only button can be used to change the network name (network password) of the local device. If a new network password is entered, all the devices seen on the Main panel prior to this will be no longer present in the new network, effectively making the local devices not to communicate to the devices who were in the old logical network. Devices previously set up with the same logical network (same network name) will appear in the device list afterward selecting this option.

The Set All Devices button is used to change the logical network of all devices that appear on the Main panel whose Device's Password had been entered for the same logical network. A dialog window will appear to report the success of this operation. For devices whose device

password's were not entered, this operation will fail and will report a failure message.

3.3 Diagnostics Screen

The Diagnostics screen shows System information and a history of all remote devices seen over a period of time. The appearance is shown in Figure 3-7.

The Upper panel shows technical data concerning software and hardware present on the host computer which were used to communicate over HomePlug on the Powerline network. It shall include the following:

• Operating System Platform/Version
• Host Network Name
• User Name
• MAC Address of all NICs (Network interface card) connected to the host
• Identify versions of all Driver DLLs and Libraries used (NDIS) and optionally
• HomePlug chipset manufacturer name
• MAC Firmware Version
• MAC addresses of all devices connected locally to the host
• Version of the Configuration Utility
• Vendor name

Power Packet Utility Main | Privacy | Diagnostics | About | System Information On NIC #1 MAC = 7A:79:00:00:00:00 No HomePlug Device Connected On NIC #2 MAC = 00:11:2F:23:23:42 HomePlug Device #1 MAC = 00:13:33:94:A3:90 Network password: HomePlugAV Vendor: Atheros Remote Device History (Log) Device MAC Address Password Rate (Mbps) Network Last Seen Device 2 00:13:33:94:A3:94 --- not entered --- 188 HomePlug...-May 03 07:33PM Delete Save Report.Print Report Close

Figure 3-7: Diagnostics Screen

The Lower panel contains a history of all remote devices seen on the computer over a certain period of time. All devices that were on the powerline network are listed here along with a few other parameters. Devices that are active on the current logical network will show a transfer rate in the Rate column; devices on other networks, or devices that may no longer exist are shown with a “?” in the Rate column. The following remote device information is available from the diagnostics screen:

• Device Alias Name
• Device MAC Address
• Device Password
• Device Last known rate
• Device Last Known Network name
• HomePlug chipset manufacturer name
• Date device last seen on the network
• MAC Firmware Version.

The diagnostics information displayed may be saved to a text file for later use, or can be printed for reference for a technical support call. Devices, which are not part of the network anymore, can be deleted using the delete button. A dialog window pops up with a confirmation message if we try to delete a device whose password has been entered.

3.4 About Screen

The About screen shows the software version.

Power Packet Utility Main | Privacy | Diagnostics | About | levelone* Power Packet Utility Version: v6.0.1.00, Build 0003 Released: October 20, 2010 Copyright c 2005-2010, Atheros Communications, Inc. All Rights Reserved. License Copyrights : Copyright (c) 1999 - 2005 NetGroup, Politecnico di Torino (Italy). Copyright (c) 2005 - 2009 CACE Technologies, Davis (California). All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. Preferences: ✓ AutoScan Close

Figure 3-8: About dialog screen

Chapter 4 – Reset and Network ID Buttons Setting

There are 2 buttons on the device, one is Reset button the other is Network ID button.

4.1 Reset Button

Push this button can reset to the factory default settings. Be careful, when you press the reset button, please remove the Ethernet cable (RJ-45cable) first, and then press the reset button. After press the reset button for less than 3 seconds and then wait the PWR LED light again. Don't power off when the device is in reset process.

4.2 Network ID Button

The HomePlug AV powerline communication devices can form multiple logical networks over a common powerline or coax medium. There are many situations when it is desirable to add new devices to, or remove old devices from, a HomePlug AV logical network.

Push this button to accomplish using HomePlug AV Simple Connect Technology.

Network ID Button trigger state conditions

"Adder state" for a device providing the NMK for an existing AVLN

"Joiner state" for a device that will join an AVLN

Pushing buttons on any two devices results in one of them becoming an “adder” and the other one a “joiner”

Four possible scenarios

This section describes how to add and remove devices using HomePlug AV Simple Connect Technology and covers some of the technical details of how the technology works.

Case 1: Forming a Network

Two devices with different network membership key (NMK) values are connected to the same powerline. The user wants them to form a logical network.

1. Press each device Network ID button > 10 sec till all LEDs re-flash to generate the random network password key first.
2. Press the button on the first device for less than 3 seconds.
3. Press the button on the second device for less than 3 seconds. The button on the second device must be pressed within 1 minute, by default however the interval is programmable.
4. Wait for connection to complete and the PLC LED will be ON.

The PWR LED on both devices will flash evenly at 1-second intervals until the operation succeeds or fails. It will illuminate steadily on successful completion. If an error occurs, the PWR LED on the ‘adder’ will flash unevenly until the Network ID button on the ‘adder’ is pressed again or the ‘joiner’ is reset by holding the Network ID buttons down for more than 10 seconds.

graph TD
    A["A STA"] --> D
    B["B STA"] --> D
    C["C STA"] --> D
    style A fill:#fff,stroke:#000
    style B fill:#fff,stroke:#000
    style C fill:#fff,stroke:#000
    note1["A and B are not part of AVLN\nA and B want to form an AVLN\nPress button on A less than 3 seconds\nPress button on B less than 3 seconds\nA becomes 'joiner'\nB becomes 'joiner'\nB determines that A MAC address < B MAC address\nB becomes 'adder'\nA accepts NMK from B"]

The join operation can be cancelled by pressing the Network ID button on the first device again, for less than 3 seconds, instead of pressing the button on the second device.

Case 2: Joining a Network

In this scenario a network exists. The user wants a new device, the ‘joiner’, to join the network. Any device on the existing network can become the ‘adder’.

1. Press the Network ID button on the 'joiner' for less than 3 seconds.
2. Press the Network ID button on any network device for less than 3 seconds, making it the 'adder'. You have 1 minute, by default, to press this Network ID button.
3. Wait for connection to complete and the PLC LED will be ON.

The PWR LED on both devices will flash at 1-second intervals until the process succeeds or fails. It will illuminate steadily on success. If an error occurs, the PWR LED on the 'adder' will flash unevenly until the Network ID button on the 'adder' is pressed again or the 'joiner' is reset by pressing the Network ID button for more than 10 seconds, as described in Case 3:

graph TD
    A["A STA"] --> B["B STA"]
    B --> C["C STA"]
    style A fill:#fff,stroke:#000
    style B fill:#fff,stroke:#000
    style C fill:#fff,stroke:#000
    note1["A and B form an AVLN\nC wants to join the AVLN\nPress button on B less than 3 seconds\nPress button on C less than 3 seconds\nB becomes 'adder'\nC becomes 'joiner'\nC accepts NMK from B"]
    note2["A and B form an AVLN\nC wants to join the AVLN\nPress button on B less than 3 seconds\nPress button on C less than 3 seconds\nB becomes 'adder'\nC becomes 'joiner'\nC accepts NMK from B"]

The join operation can be cancelled by pressing the Network ID button on the first device again, for less than 3 seconds, instead of pressing the Network ID button on the second device.

If you press Network ID buttons on three or more devices, only the first two will respond. The others will not. See Case 4 for a variation on this rule.

You can press the Network ID button on the ‘adder’ before pressing the Network ID button on the ‘joiner’. It does not matter which is pressed first. See Case 4 for a case where the ‘adder’ may be pressed before the ‘joiner’. Once a ‘joiner’ becomes a member of the network, it may become the ‘adder’ in the next join operation.

Case 3: Leaving a Network

A network exists. The user wants to remove one device, the ‘leaver’, from that network, for whatever reason. He may want to remove the device from service altogether or have it join another logical network.

1. Press the Network ID button on the 'leaver' for at least 10 seconds. The device will reset and restart with a random NMK.

2. Wait for reset to complete and the PLC LED will be OFF.

The PWR LED on the 'leaver' will momentarily extinguish during reset, flash during restart then illuminate steadily. No errors can occur.

graph TD
    A["A STA"] --> B["B STA"]
    B --> C["C STA"]
    style A fill:#f9f,stroke:#333
    style B fill:#f9f,stroke:#333
    style C fill:#f9f,stroke:#333
    note1["Press button on A more than 10 seconds"]
    note2["A computes random NMK"]
    note3["A resets and restarts"]
    note4["A, B and C form on AVLN"]
    note5["A wants to leave the AVLN"]

Once the process completes, the user may disconnect the device from the medium or join it to another logical network on the same medium, as described in either Case 1 or Case 3.

Case 4: Join Multiple Devices to a Network

To add several new devices to an existing network, the process in Case 2 must be repeated for each 'joiner'. A vendor may implement a mode of operation in which an 'adder' device in the network remains in the adder state for an extended period allowing additional 'joiners' to be added in turn. This lets you press the 'adder' Network ID button once then press each 'joiner' Network ID button in turn.

If Network ID buttons are pressed on two or more joiners, only the first one will respond. The second will not. This makes timing important.