AFGB14BBAA-B - Air-conditioner FUJITSU - Free user manual and instructions

USER MANUAL AFGB14BBAA-B FUJITSU

Instruction / Operation Manual for Users

Contents

Know Your Air conditioner - Features .... 1

Installation 2

Remote Control 5

Using the Remote Control 6

Remote Control Operation 7

Manual Operation 12

Device Protection Measures 13

Tips for Comfort and Economy 14

Caution 15

Troubleshooting Chart 16

Care and Maintenance 17

Know Your Air Conditioner

Features

Great Looks

Power Saver Compressor

4-Way Air Distributor

Slide-Out Chassis

4-Speed Cooling

Long Life

Most Advanced Fan Motor

Swing

Removable Filter

Feather Touch Controls

Programmable Timer

Digital Display

Full Function Remote

Turbo Cooling

Sleep

Energy Saver

Please get the unit install from FUJITSU GENERAL (INDIA) PRIVATE LIMITED authorised Channel Partner only an authorised Technician to install the airconditioner for you as many factors need to be considered for the efficient performance of your Window Airconditioner. For any type of support please contact FUJITSU GENERAL (INDIA) PRIVATE LIMITED toll free number-1860 208 1007

• To get the best results, install the window airconditioner at window sill level.
- Ensure that neither the air-throw outlet and air-intake grill is blocked by any furniture or other such equipment, for a distance of at least three feet.
- Identify the area within your room which you are most likely to occupy. Then ensure that there is a line-of-sight view from there the window airconditioner, because otherwise you cannot use your remote control conveniently.
• Install the airconditioner as much to the centre – of the wall as possible. Avoid using a corner.
- Do not install the airconditioner too close to an entrance which is likely to be opened and closed frequently.
- Outside the room, ensure that the hot air from the rear end of the unit discharges freely into the open atmosphere. A minimum clearance of 30cm on the two sides and 1.0m at the rear of the external portion of your airconditioner is advisable.
- Select a location that supports the weight of your airconditioner. also, there should be no vibration as that results in increased noise.

graph TD
    A["Top Section"] --> B["Top Section with a fan icon, arrow pointing to a plant"]
    B --> C["Top Section with a solar panel, arrow pointing to a drain"]
    C --> D["Top Section with a solar panel, arrow pointing to a drain"]
    D --> E["Top Section with a solar panel, arrow pointing to a drain"]
    E --> F["Top Section with a solar panel, arrow pointing to a drain"]
    F --> G["Bottom Section with a vertical line and 1m dimension annotation"]

Note - The above figures are only intended to be a simple diagram of the appliance and not correspond to the appearance of the units that have been purchased.

Horizontal Line 10~15mm Wall Wooden Frame Rubber Plate Sunshade Board 10~15 mm Support Horizontal Line

Procedure

1. Remove the tape from the front panel.
2. Insert the unit into the installation opening space, which should be created slightly larger than the unit size. When installing the unit, it should be slanted in backwards (by 10-15mm).
3. Fill up gaps between the cabinet (unit) and the wood work/support structure with sponge or foam.

Support & Protection

• Use Iron Support

If the installation opening is not strong enough to support the airconditioner, iron supports should be installed externally on the building.

• Use Sunshade Board

Install a sunshade over the unit on the outside to prevent direct sunlight on it, as well as to protect it from falling objects.

Drain Pan (Compulsory addition of drain pan) To achieve maximum cooling efficiency, the air conditioner is designed to splash the condensation water on the condenser coil.

In order to avoid the splashing sound, an external drain can be provided by using the following This may however cause a small loss of performance.

1. Slide out the chassis from the cabinet.
2. Remove the rubber plug from the body base plate.
3. Install the drain pan at the corner of the cabinet with two screws.
4. Connect the drain hose to the outlet on the bottom of the drain pan.
5. Slide the chassis into its original place in the cabinet.

Relocation

To relocate the airconditioner, please contact your dealer. Relocation should be carried out only under the direction of an authorised FUJITSU GENERAL (INDIA) PRIVATE LIMITED Channel Partner and for more details and support please contact FUJITSU GENERAL (INDIA) PRIVATE LIMITED toll free number-1860 208 1007

Electric Wiring

• Ensure proper earthing.
• Use an exclusive circuit.
• Do not use removable sockets which could
• lead to poor contact.
• Use approved voltage stabilizer.

Screws Drain Pan

Internal View

Drain Hose

External View

Power Cord A E N MCB

MCB RATING

16 Ampere for 1 TON

20 Ampere 1.5TON

CABLE SIZE

1.0 Sqmm for 1Ton

1.5 Sqmm for 1.5Ton

COLOR CODING

A-Red

N-Black

E-Green/Yellow

Remote Control

Remote Controller Overview

Remote controller display * The accompanying illustration depicts the display with all indicators lighted; in actual use, however, only those indicators currently required are displayed. Operation Mode Indicator Shows the operation mode (AUTO, COOL, DRY, and FAN) Timer Mode Indicator Shows the timer mode O : "OFF TIMER" symbol I : "ON TIMER" symbol ✓ : "SLEEP TIMER" symbol MODE button Press to select operating mode (AUTO, COOL, DRY, FAN) SET TEMP. buttons ( △ / ▽ ) Press to set the unit's thermostat. TEST RUN button This button is used when testing the air conditioner after installation. Do not use under normal condition. SLEEP button Use to set time for OFF the air conditioner. OFF TIMER button Use to set time for OFF the air conditioner. Set temperature / Timer Indicator ● Shows the thermostat setting. ● During the timer mode is set, the function is displayed. (After the timer mode is shown, the thermostat setting is returned to temperature indication.) Fan Speed Indicator Shows the current fan speed. Transmit Indicator Displayed when a signal is sent to the air conditioner. Signal Transmitter Controls signal sent to the air conditioner from here. FAN button Press to select fan speed. (AUTO, HIGH, MED, and LOW). SUPER WAVE button Use to set the desired airflow direction. START/STOP button Press to start and stop operation. RESET button This button is used when replacing batteries. CANCEL button Press to cancel the setting time. ON TIMER button Use to set time for ON the air conditioner.

Using the Remote Control

CHANGING BATTERIES

1. Slightly press the battery cover where it is marked in the arrowhead direction to open the battery compartment of the remote control.
2. Take out the old batteries.
3. Insert two new AAA 1.5V dry batteries. When inserting the new batteries, pay attention to the polarity.
4. Reattach the back cover of the remote control.

NOTE :

• Do not use old batteries, or batteries of different brands as this can cause malfunction of the wireless remote control.
• Remove the batteries if the remote control is not going to be used for a long time.
  ☐ Operation should be within the receiving range of the remote control.
  ☐ The remote control should be placed at least 1m away from television or audio systems.

BE SURE TO OBSERVE THE FOLLOWING :

• During operation, make sure that the remote control is aimed at the control panel on the airconditioner.
• Do not drop or throw remote control.
• Do not place the remote control in a location that is exposed to direct sunlight or next to a heating unit or other heat source.

AUTO COOL DRY FAN AUTO HIGH MED LOW MODE SET TEMP. FAN SUPER WAVE TEST RUN START STOP RESET SLEEP TIMER OFF ON CANCEL REMOTE slide the back cover REMOTE CONTROLLER 1

Note - The above figures are only intended to be a simple diagram of the Remote and not correspond to the appearance of the Remote that have come with your unit.

Remote Control Operation

Key on the Unit Display :

There is only one Keys on the Receiver Unit.

Manual Auto Button 📋/1. Press 10 Seconds or less (Automatic Mode)
Fan speed will be set to "AUTO" and the thermostat will be set for 24°C.
To stop operation, either press the MANUAL AUTO button once again.
➢ Swing should be run on Left to right.
What will be swing status at this manual mode?
➢ Swing should be run on Left to right. Press 10 Seconds or more (Forced Cooling)
The forced cooling operation is used at the time of installation.
When the forced cooling operation starts by any chance, press START/STOP button to stop the operation.
➢ After entering in Forced cooling mode machine follow below steps:
➢ Display LED glow (left green → Orange → Right green)
▶ Compressor Start immediate.
➢ Swing start immediate (Left to right).
➢ Fan speed change (Low → Med → High), Fan run on every speed for 30 sec.
➢ Check all the sensors error codes if any abnormality occurs (Error code detect). Machine should come out from forced cooling mode and turn off machine (LED blink as per detect error)
If no any abnormality, Machine turn off after 3 min.
This statement is newly added from previous. Need to update in software.
Update logic in software.

Remote Control Features :

Various Keys & the function associated with them are as follows: -

• START/STOP : To switch the system ON or OFF.
• SET TEMP UP : Used for incrementing the preset temperature.
• SET TEMP Dawn : Used for decrementing the preset temperature.

- Mode : Changes the mode to Cool, Dry, Fan, Auto.

• FAN : To change fan speed (Low, Med, high, Auto).

• SUPER WAVE : To change Swing Mode.

- Sleep : To activate the sleep function and to change the time of sleep function.

- Timer OFF : To Set Off timer.

- Timer ON : To Set ON timer.

- CANCEL : To cancel SLEEP TIMER/TIMER OFF/TIMER ON.

- Test Run : This button is used when testing the air conditioner after installation.

Do not use under normal condition (Logic is same as forced cooling).

Remote Control Operation

Modes of Operations : Various modes of operation of the unit are as follows :-

• Auto Mode
  Cool Mode
  Dry Mode
  Fan Mode

Auto Mode :-

• Set Temp Change between 18^ to 30^ .
• Fan Speed can be selected by the user with the Transmitter (Low, Medium, High or Auto – fan speed).
• Swing mode can be change.
• When Automatic operation first selected, the fan will operate at low speed for 1 minute, during which time the unit detects the room conditions and selects the proper operating mode.

If the difference between thermostat setting and actual room temperature is more than +2^ Cooling operation If the difference between thermostat setting and actual room temperature is less than +2^ Dry operation.

- If the mode automatically selected by the unit is not what you wish, select one of the mode operation (COOL, DRY and FAN.)

• After the system mode is selected, it will not change with indoor Ambient.

- The operation mode will be reselected after the Power OFF OR Mode selection or change set temp.

Cool Mode:-

• Set Temp Change between 18°C to 30°C
- In this mode of operation, compressor will be switched on after a delay time of three minute depending on the differential of Room temperature & Set Temperature.
- Preset temperature and fan speed can be changed by the user.
• Swing mode can be change.
- Fan Speed can be selected by the user with the Transmitter (Low, Medium, High or Auto – fan speed).

• Compressor will work as per the following conditions:

• Compressor will cut off, If Room temperature= Preset temperature - 1°C or Below
• Compressor will cut in, If Room temperature = Preset temperature + 1°C or Above

Dry Mode :-

• Set Temp Change between 18^ to 30^ .
• Fan speed can't change, fix on Auto.

• Swing mode can be change.
  Initial startup: - The comp on /off duration is controlled by difference between room temperature and set temperature as follows: -

• RT = ST + 2°C or above - Comp ON for 15 min OFF for 5min.

• RT=ST + 1°C - Comp ON for 10 min OFF for 10min.
  • RT = ST - Comp ON for 10 min OFF for 10min.
• RT = ST-1°C - Comp ON for 10 min OFF for 10min.
• RT = ST-2°C or below - Comp ON for 5 min OFF for 15min. Where, RT=Room temperature & ST=Preset temperature.

Remote Control Operation

Fan Mode : -

• In this mode, Compressor will be switched off.
• Fan Speed can be selected by the user with the Transmitter (Low, Medium and High–fan speed, Auto).
• Swing mode can be change

Additional Features :-

• Auto fan speed (in Cool mode/Auto mode/Dry Mode): While increasing room temperature:
• Low fan change to medium when room temperature> set temperature. + 2°C.
• Medium fan change to high when room temperature > set temperature + 4°C While decreasing room temperature:
• High fan change to medium when room temperature< set +2°C
• Medium fan change to low when room temperature < set temperature.

• Auto Fan Speed (In Fan Mode): -

• If Tr > 27°C (Fan run on High Speed).

- 24^ < Tr ≤ 27 (Medium Fan Speed).

- Tr≤24°C (Low Fan Speed).

Note: - From High to Low Speed delay time is 3 min.

Sleep (Cooling/Dry) :-

• Like OFF timer Function, the SLEEP timer is used to set the length of time until air conditioner operation is stooped.
• When the SLEEP timer is set, the thermostat setting is automatically raised 1°C every 1 hour.
• When the thermostat has been raised a total of 2^ C the thermostat setting at that time is maintained until the set time has elapsed, at which time the air conditioner automatically turns off.

Remote Control Operation

To Use the SLEEP TIMER

While the air conditioner is operating or stopped, press the SLEEP button 📋SLEEP.

The SLEEP TIMER indicator ( ⭕ ⭕▶○ ) on the remote controller's display will light.

Within 3 seconds after the indicator lights, the time can be changed by pressing SLEEP button once again.

Each time the button is pressed, the time changes in the following order:

graph LR
    A["1.0 → 2.0 → 3.0 → 5.0 → 7.0 → 9.0 (hour)"] --> B["(RESET)"]

About 3 seconds later, the entire display will reappear.

The unit's OPERATION indicator (green) and the TIMER indicator (orange) light.

SLEEP timer setting Set time 1 hour 1 °C 2 °C

To Change the SLEEP TIMER Settings

Press the SLEEP button once to display the last setting time.

Press the SLEEP button again to change the time.

Each time the button is pressed, the time changes in the following order (Change from the last setting time):

graph LR
    A["1.0 → 2.0 → 3.0 → 5.0 → 7.0 → 9.0 (hour)"] --> B["(RESET)"]

To Cancel the TIMER

Press the CANCEL button CANCEL.

To Stop the Air Conditioner Operation while the TIMER is Operating

Press the START/STOP button.

Remote Control Operation

TIMER Operation

OFF TIMER (stops the air conditioner operation at the set time)

1 Press the START/STOP button. (if the unit is already operating, proceed to step 2). The unit's green OPERATION indicator will light.

2 Press OFF TIMER button to select desired times. Press OFF TIMER button to change from temperature setting to timer indicator. Each time the button is pressed, the time changes in the following order:

Set the time while the OFF TIMER indicator ( ) on the remote controller's display is flashing.

AUTO CDCL DXY FAN MODE EET TEMP. FAN TURN WAVE 1 2 EAT TIME OUT ON OK OFF ON

ON TIMER (begins the air conditioner operation at the set time)

1 Press the START/STOP button.
(If the unit is already operating, proceed to step 2.) The unit's green OPERATION indicator will light.

2 Press ON TIMER button to set the expected time. If ON TIMER button is pressed, it will be changed into time indication from temperature indication. Each time the button is pressed, the time changes in the following order:

Set the time while the ON TIMER mark ( ⊙▶ | ) on the remote controller's display is flashing.

AUTO COOL SPAY RAN MODE SET TEMP. RAN 200V/4A WAVE 1 SLEEP ON ON CANCE 1 2

To Cancel the TIMER

Press the CANCEL button CANCEL.

To Change the TIMER Settings

Press the ON TIMER button ON or OFF TIMER OFF button as required.

To Stop the Air Conditioner Operation while the TIMER is Operating

Press the START/STOP button.

To Change Operating Conditions

If you wish to change the operating conditions (mode, fan speed, thermostat setting), after making the timer setting, wait until the entire display reappears, then press the appropriate buttons to change to the desired operating condition.

Manual Operation

Remote control signal receiver Signals from the remote control unit are received here. OPERATION indicator (Green)

SUPER WAVE indicator (Green)

Lights during SUPER WAVE working.

MANUAL AUTO button

• Pressed 10 seconds or less (AUTOMATIC mode)
• Fan speed will be set to "AUTO" and the thermostat will be set for 24 °C.
• To stop operation, either press the MANUAL AUTO button once again.
  ● Pressed 10 seconds or more (Forced cooling)
• The forced cooling operation is used at the time of installation. Only for authorized service personnel's use
• When the forced cooling operation starts by any chance, press START/STOP button to stop the operation.

Remote control signal receiver

Signals from the remote control unit are received here.

OPERATION indicator (Green)

● Lights when unit is operating.
● Flashes quickly for about 1 second when a signal is received from the remote control unit.

TIMER indicator (Orange)

Lights during ON TIMER, OFF TIMER, and SLEEP TIMER.

If the TIMER indicator flashes when the timer is operating, it indicates that a fault has occurred with the timer setting.

Device Protection Measures

Controller starts with a default memory if the nonvolatile memory fails.

• Mode : Cool
• Timer : Off
• Set temperature: 25^ C
• Fan Speed : High
• Swing Motor : ON

Room Sensor Failure: -

- Room sensor failure occurs when the room sensor is short or open. Compressor gets on for 20 minutes & off for 07 minutes & repeats this cycle irrespective of the set temperature.

Coil Sensor Failure: -

- Coil sensor failure occurs when the coil sensor is short or open. Compressor works like cool mode.

Evaporator Unit Frost prevention (Cool mode / Dry Mode):

• When ECT * Reached 2 deg. C or below for 1 min
  Compressor cut off immediately and Fan runs with low Speed.
• When ECT* Reached on 12 deg. C or above.
  Compressor will turn on according to Room Temperature (With 3 minutes' delay)

• (ECT: Evaporator Coil Temperature.)

Tips for Comfort and Economy

Do not overcool the room :

This is not good for health and wastes electricity.

Keep blinds or curtains closed :

Do not let direct sunshine enter the room when the airconditioner is in operation.

Keep room temperature uniform :

Adjust vertical and horizontal airflow direction to ensure uniform temperature in the room.

Make sure that the doors and windows are closed :

Avoid opening doors and windows as much as possible to ensure effective air conditioning in the room.

Clean the air filter regularly :

Blockages in the air filter reduce dehumidifying effects. Clean the air filter at least once every two weeks.

Ventilate the room occasionally :

Since windows are kept closed, it is a good idea to open them and ventilate the room periodically. When starting the unit, curtains and windows should be closed to prevent loss of coolling.

Caution

• Do not pull out the power cord.
• Damage to the cord may result in serious electric shocks.
• Do not use the airconditioner for purposes other than for cooling the room.
• Do not block the air intake and outlet vents. This causes lowered performance and irregular operation.
• Do not insert sticks or other object into the vents as it is dangerous to touch the electric components and the fan.
• Select the most appropriate temperature to suit the prevent weather conditions.
• Do not use heating apparatus in the vicinity. The airconditioner's plastic parts may melt if exposed to excessive heat.
• Avoid exposing yourself and others directly to a continuous unidirectional air flow for long periods. This is not recommended for health reasons.
• always wait at least three minutes before switching the airconditioner on agian after you have switched it off.
• Always turn off the airconditioner and main power supply before cleaning, to ensure safety.

In the following situations, immediately stop operation of the unit and contact FUJITSU GENERAL (INDIA) PRIVATE LIMITED tollfreenumber-18602081007

• Operation starts or stops abnormally.
• Power fuse or switch often breaks.
• Water or other liquid is accidentally splashed into the air conditioner.
• Electrical lines are very hot or lines cover breaks.
- other abnormal situations.

Troubleshooting Chart

graph TD
    A["Air Filter"] --> B["Super Wave"]
    B --> C["WIRELESS SWITCH FILTER"]
    C --> D["Fuse"]
    D --> E["Switch on the MCB"]
    E --> F["Stabiliser"]

Symptoms	Possible Causes	Suggested Remedy
Unit does not start	MCB has tripped	Reset MCB
	Fuse has burnt	Replace fuse wire
	Input voltage to the stabilizer is below acceptable range	Wait for input voltage to come with acceptable range.
		If it is perennial problem pls go for buck-boost stabilizer to get the required input voltage.
Unit does not cool (Even after the normal Time Delay of approx. 2/3 minutes for compressor to start)	The airflow paths are not free	Remove all obstructions to make the airflow paths free
	The Unit is in the fan mode	Change to AC/cool mode
	Selected temperature is more than room temperature	Make the selected temperature less than room temperature
	Air-filter is not clean	Clean the air-filter

Note : if the unit still not work, or if any other types of symptoms are encountered, shut off the mains (switch fuse unit) and contact FUJITSU GENERAL (INDIA) PRIVATE LIMITED toll free number-1860 208 1007

Care and Maintenance

Cleaning the Unit

Turn off power before cleaning. 1.

1. Use soft cloth while cleaning the cabinet. If the cabinet is very dirty, dip cloth into warm water below 40^ C. The air filter behind the intake grille should be washed at least once every two weeks or as often as it needs cleaning.
2. Do not use gas, benzene, solvent, wash, chemical solvent etc. for cleaning
3. Do not splash water directly on the indoor unit as, it may damage the microcomputer or circuit plate.

Air Filter

As mentioned, the air filter behind the intake grille should be washed at least once every two weeks or as often as it needs cleaning.

Cleaning the Air Filter

1. To remove the air intake grille, grasp the tab on the filter and pull to take out.
2. Vacuum clean the filter on the dusty side to remove light dust.
3. Wash the filter, cleaner side up under gently flowing water to wash out accumulated dust and lint.
4. If the filter is very dirty, use a mild household detergent in the wash water. Let the filter dry thoroughly before reinstalling it. If necessary, please ask professional personnel to clean it.
5. Check if air inlet and outlet of outdoor unit is blocked.

Disposal

Your FUJITSU GENERAL (INDIA) PRIVATE LIMITED product is designed and manufactured with High quality materials and components which can be recycled and/or reused. This symbol means that electrical and electronic equipment, batteries and accumulators, at their end-of-life, should be disposed of separately from your household waste. If a chemical symbol is printed beneath the symbol (Fig. 1), this chemical symbol means that the battery or accumulator contains a heavy metal at a certain concentration.

This will be indicated as follows: Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%).

ACW5PR08501

ACW5PR08501-R0

GENERAL

FUJITSU GENERAL (INDIA) PRIVATE LIMITED

Prestige Cosmopolitan, No:36, 8th Floor, Sardar Patel Road, Guindy, Chennai - 600032, Tamil Nadu, India.

Customer Care Toll Free Number:

1860 208 1007

E-mail : [e-mail]