TM-4010HDMI - Point of Sale Terminal Posiflex - Free user manual and instructions

USER MANUAL TM-4010HDMI Posiflex

Black rectangular electronic device with a blank screen (no visible text or symbols)

Package Contents

√ POS Monitor .....(x1)
√ Power Adaptor....(x1)
√ Power Cable (for HS/PS System).....(x1)
√ HDMI Cable....(x1)
√ USB (Type B) Cable.....(x1)
(For touch monitor and camera only)
√ Mounting Kits (for HS/PS System)...(x1)

FCC NOTES

This system meets industry & government requirements and applicable standards. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart B of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CE CLASS A WARNING

This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may cause radio interference.

AVERTISSEMENT CE CLASSE A

Warranty will terminate automatically when the machine is opened by any person other than the authorized technicians. The user should consult his/her dealer for the problem happening. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.

LIMITES DE GARANTIE

This equipment is not suitable for use in locations where children are likely to be present.

CONSIGNES DE SÉCURITÉ

LM-401xHDMI LCD Panel

TM-401xHDMI P-CAP Touch Panel

Panel

Rear View

VESA-Mount Screw Holes

graph TD
    A["Top Node"] --> B["Square Node"]
    B --> C["Circle Node 1"]
    B --> D["Circle Node 2"]
    B --> E["Circle Node 3"]
    B --> F["Circle Node 4"]

Bottom View

I/O Ports Status LED Indicator

Introduction to the I/O Ports

DC-IN Power Jack USB (Type-B) Port HDMI Port VGA Port

Connecting LM-4010HDMI/TM-4010HDMI/LM-4011HDMI/TM-4011HDMI to a HS-series POS Terminal

Before connecting your POS monitor to a HS-series POS terminal, please enable the power supply from the POS terminal to your POS monitor by setting up the jumper of the POS terminal. It is suggested that professional technicians implement the POS terminal jumper setting. To get more detailed information on jumper setting, contact directly your local service center.

During connection, please ensure the terminal is properly powered off and disconnected from the power sources to avoid potential hazards.

To connect your monitor to a HS-series POS terminal, please follow the below instructions.

1. Remove the top I/O cover of your HS terminal.

Top I/O Cover

1. Fix your LM/TM-series monitor to the HS terminal with 4 #6/32-8L screws.

Close-up of a black electronic device with a small rectangular component inserted, shown from an inset view (no text or symbols visible)

Close-up of a remote control panel showing internal components and mounting points (no text or symbols visible)

1. Connect the HDMI cable, power cable, and USB cable (only for camera and touch screen) to your LM/TM-series monitor and the HS series terminal. Put the cable cover back to the HS series terminal. Please refer to the cable introduction on P.7.

Connecting LM-4011HDMI/TM-4011HDMI to a PS-series POS Terminal

Before connecting your POS monitor to a PS-series POS terminal, please enable the power supply from the POS terminal to your POS monitor by setting up the jumper of the POS terminal. It is suggested that professional technicians implement the POS terminal jumper setting. To get more detailed information on jumper setting, contact directly your local service center.

During connection, please ensure the terminal is properly powered off and disconnected from the power sources to avoid potential hazards.

To connect your monitor to a PS-series POS terminal, please follow the below instructions.

1. There is four screw holes on the rear side of the PS-series POS terminal.

Close-up of a computer monitor with an attached USB port and two gold screw holes, shown in a close-up inset (no text or symbols visible)

1. Fix your LM/TM-4011HDMI to the PS-series POS terminal with four #6/32-10L screws

Close-up of a black electronic device with two metallic connectors and mounting holes (no visible text or symbols)

1. Connect the HDMI cable, power cable, and USB cable (only for camera and touch screen) to your LM/TM-series monitor and the PS series terminal. Put the cable cover back to the PS series terminal. Please refer to the cable introduction on P.7.

Power Cable

Coiled black cable with two connectors and dotted arrows indicating connection (no text or symbols on the cable itself)

Connect to POS Terminal

Connect to POS Monitor

HDMI Cable

Connect to POS Monitor

Monitor

Connect to POS Terminal

USB (Type B) Cable

(For touch monitor and camera only)

Connect to POS Monitor

Coiled black cable with two connectors and dotted arrows indicating direction (no text or symbols)

Connect to POS Terminal

CAUTION: On doing insertion or extraction of a cable connector, please always hold the connector head itself instead of pulling the cable wire. Doing this could damage the cables and ports, which is considered as an artificial damage and is not covered by the warranty. The means of power cord should be connected to a socket-outlet with earthing connection.

Identifying your Monitor as Secondary Touchscreen Monitor in Extended Mode

In the following section, the related descriptions will be offered to help you set up TM series as the extended monitor when you attempt to extend the desktop across multiple monitors

For TM-4010HDMI/4011HDMI Models with P-CAP Touchscreen

If your monitors are TM-4010HDMI/TM-4011HDMI models, you may configure the display settings from Control Panel in Microsoft Windows to identify the monitor as the secondary touchscreen monitor. Please go through the below steps to complete configuration.

1. Make sure that the monitor is well connected to your POS terminal.

2. Go to Control Panel>Display Settings, change your display settings to extended mode.

3. Go to Control Panel, and then click on Tablet PC Settings item.

4. In Tablet PC Settings dialogue box, click on Setup button.

Kemotieapp and Desktop Storage Spaces Tablet PC Settings User Accounts Windows Update

Tablet PC Settings Display Other Configure Configure your pen and touch displays. Setup... Display options Display 102. Multiple Monitors Details Limited Touch Support Callrate... Reset...

1. Following the instruction shown on the screen, click on the screen that you want to identify as the primary touchscreen display.

Touch this screen to identify it as the touchscreen.

If this is not the Tablet PC screen, press Enter to move to the next screen. To close the tool, press Esc

1. Press Enter button to proceed the configuration.

Press Enter to proceed to the next step to complete your configuration

1. Click on the screen you want to use as the secondary touchscreen display.

Touch this screen to identify it as the touchscreen.

If this is not the Tablet PC screen, press Enter to move to the next screen. To close the tool, press Esc

Powering ON/OFF your Monitor

To start up LM/TM-401xHDMI, please make sure that the monitor is well connected to the POS terminal and the power is supplied to the monitor through POS terminal.

Installing Drivers

Please visit Posiflex official website to download and install the related drivers. http://download.posiflex.com/en-global/Download/download)

Setting up Display Resolution for Your Monitor

The below chart defines the list of recommended display settings for LM/TM-401xHDMI. Improper display configuration will prevent the monitor from properly displaying the image and lead to a warning message of “out of range” prompted on the screen.

9.7" LM/TM-4010HDMI

Display Resolution	Horizontal Frequency (KHz)	Refresh Rate (Hz)
640 x 400	37.9	70
640 x 480	31.5	60
	37.9	72
	37.5	75
720 x 400	37.9	70
800 x 600	35.137.9	5660
	48.1	72
	46.9	75
1024 x 768	48.4	60

10.1" LM/TM-4011HDMI

Display Resolution	Horizontal Frequency (KHz)	Refresh Rate (Hz)
640 x 480	31.5	60
	37.9	72
	37.5	75
800 x 600	37.9	60
	48.1	72
	46.9	75
1024 x 768	48.4	60
1280 x 720	45.0	60
1280 x 800	49.7	60

Specification

	LM/TM-4011HDMI	LM/TM-4010HDMI
Display
LCD Panel	10.1" TFT LCD	9.7" TFT LCD
Resolution	1280(H) x 800 (V)	1024(H) x 768 (V)
Active Area	216.96mm (H) x 135.60mm (V)	196.61mm (H) x 147.46mm (V)
Pixel Arrangement	R.G.B. Vertical Stripe
Viewing Angle	85/85/85/85 degree (U/D/L/R)	70/60/70/70 degree (U/D/L/R)
Contrast Ratio	800 : 1	500 : 1
Response Time	25ms	20ms
Brightness	400 cd/m2	350 cd/m2
Display Interface	VGA Port / HDMI Port
Power Supply	12V from Posiflex terminal VGA Port12V from Posiflex terminal 12V DC-OUT Power Jack12V from 12V/18W power adaptor
Touch
Touch type	P-CAP	N/A	P-CAP	N/A
Interface	USB	N/A	USB	N/A
I/O Ports
HDMI Port	1 Port
VGA Port	1 Port
USB Port	1 Port (Type B)
DC-Jack	12V DC-IN

※ The product information and specifications are subject to change without prior notice.