PD1611 - Projector VIEWSONIC - Free user manual and instructions

USER MANUAL PD1611 VIEWSONIC

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right corner of our website. "Antes de operar su equipo lea cu idadosamente las instrucciones en este manual"

Model No. VS16164

Thank you for choosing ViewSonic

With over 25 years as a world leading provider of visual solutions, ViewSonic is dedicated to exceeding the world's expectations for technological evolution, innovation, and simplicity. At ViewSonic, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic product you have chosen will serve you well.

Once again, thank you for choosing ViewSonic!

ViewSonic®

Compliance Information

For U.S.A.

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

CE The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC.

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

If the batteries, accumulators and button cells included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.

Important Safety Instructions

1. DO NOT place objects on top of the device, as objects may scratch the screen.
2. DO NOT expose the device to dirty or dusty environments.
3. DO NOT place the device on an uneven or unstable surface.
4. DO NOT insert any foreign objects into the device.
5. DO NOT expose the device to strong magnetic or electrical field.
6. DO NOT expose the device to direct sunlight as it can damage the LCD Screen. Keep it away from heat sources.
7. DO NOT use the device in the rain.
8. Please check with your Local Authority or retailer for proper disposal of electronic products.
9. The device may produce some heat during normal operation or charging. To prevent discomfort or injury from heat exposure, DO NOT leave the device on your lap.
10. POWER INPUT RATING: Refer to the rating label on the device. Only use accessories specified by the manufacturer.
11. DO NOT use any sharp object to tap the screen.
12. Clean the touch screen with a soft cloth. If needed, dampen the cloth slightly before cleaning. Never use abrasives or cleaning solutions.
13. Disconnect the device from an electrical outlet and power off before cleaning the device.
14. DO NOT disassemble the device. Only a certified service technician should perform repair.
15. Users have to use the connection to USB interfaces with USB 2.0 version or higher.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance	Proposed Maximum Concentration	Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium ( Cr^6+ ) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE)	0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

(1) Short length ( ≤ 500 mm): maximum 3.5 mg per lamp.
(2) Medium length (>500 mm and ≤ 1,500 mm): maximum 5 mg per lamp.
(3) Long length (>1,500 mm): maximum 13 mg per lamp.

1. Lead in glass of cathode ray tubes.
2. Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
3. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
4. Copper alloy containing up to 4% lead by weight.
5. Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
6. Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

Copyright Information

Copyright © ViewSonic® Corporation, 2016. All rights reserved.

ViewSonic and the three birds logo are registered trademarks of ViewSonic Corporation.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes available, please register your product on the Internet at: www.viewsonic.com.

For Your Records

Product Name: PD1611

ViewSonic Pen Display

Model Number: VS16164

Document Number: PD1611_UG_ENG Rev. 1B 02-24-17

Serial Number:

Purchase Date:

Product disposal at end of product life

ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

Contents

Compliance Information......i

Important Safety Instructions......iii

Declaration of RoHS2 Compliance......iv

Copyright Information......v

Product Registration......v

1. Introduction......1

1.1 Packing list .... 1

1.2 Product overview....1

1. Installation and Setting .... 3

2.1 Install driver....3

2.2 Set the display area....5

2.3 Handwriting area correspondence 6

2.4 More touch settings....7

1. Troubleshooting 9

3.1 Screen problems ......9

3.2 Problems of interactive electromagnetic pen 10

1. Product Specification....11

4.1 Screen.... 11

4.2 Interactive electromagnetic pen 12

1. Appendix.... 13

5.1 Replace the pen tip 13

Customer Support 14

Limited Warranty 15

1. Introduction

1.1 Packing list

After unpacking, please confirm whether the following contents are included:

● Electromagnetic pen display
● Electromagnetic pen display support
● Power adapter
- USB 2.0 Y cable
- Electromagnetic pen
- Pen rope
- Pen tip x 3
- Pen tip replacement tool
- Quick Start Guide
● Driver and instructions disk
● Warranty card (only Chinese zone)

For any part flaws or defects, please consult the original product dealer.

1.2 Product overview

1.2.1 Front view and side view

ViewBasic ① ② ③ ④ ⑤ ⑥

① Display and electromagnetic pen touch area
② Pen holder
③ Power button
④ Brightness adjustment button (turn up)
⑤ Brightness adjustment button (turn down)
⑥ Ergonomic support

1.2.2 Rear view

⑧ ⑨ ⑦ ⑩ ⑪ ⑨ ⑧

⑦ Pen slot
⑧ Pen rope hole (×2)
⑨ Lock hole (×2)
⑩ USB output interface
⑪ Power interface

Note: please don't open the enclosure, which exists electric shock hazard. Please contact with the service personnel for any problem.

1.2.3 Interactive electromagnetic pen

The interactive electromagnetic pen is made with electromagnetic resonance technology and does not require batteries.

2. Installation and Setting

2.1 Install driver

Connect the device and PC/NB with attached USB cable and plug in the power adapter, as shown below.

Diagram showing connection between a desktop computer tower, USB cable, and network device via cable routing to a monitor.

2.1.1 Install DisplayLink display adapter driver and software

1) Open the driver and attached software disk, and click and install [DisplayLink-xx.exe] at Windows.

正在为 DisplayLink Device 安装 DisplayLink 软件 汉语(简化) 7.9.1488.0 DISPLAYLINK SOFTWARE LICENSE AGREEMENT IMPORTANT - READ BEFORE COPYING, INSTALLING OR USING. Do not install or use this software and any associated materials (collectively, the "Software") until you (individual or entity) have carefully read the following terms and conditions. By installing or using the Software, you agree to the terms of this Agreement. If you do not wish to so agree, do not install or use the Software. 1. LICENSES: • If you are an end user, the "SINGLE USER LICENSE" below shall apply to you. • If you are a network administrator, the "SITE LICENSE" below shall apply to you. 同意 取消

2) Click [Agree] to start the installation. Then, the installer will be automatically completed.

2.1.2 Install handwriting driver

1) Open the driver disk, click and install [viewsonic-xx.exe] at Windows, Pen Display Manager will appear on the start page immediately.

Pen Display Manager

The Installation Wizard will install Pen Display Manager on your computer. To continue, click OK.

2) Then, complete all steps as per the setting guide.

Pen Display Manager

License Agreement License Agreement and Limited Warranty IMPORTANT: Read this License Agreement and Limited Warranty (hereafter, the "Agreement") before continuing to load any ViewSonic software, or before using any third-party software containing any ViewSonic software (hereafter, the "Software"). By loading or using ViewSonic Software, you are accepting the terms of this Agreement between you, the Licensee, and ViewSonic Corporation. ("ViewSonic"), the Licensor. If you do not agree to the terms of this agreement, do not load the Software and promptly return or delete it. If you do not agree to the terms of this Agreement, you have no right to use the Software in any way whatsoever. 1. Limited Use License: ViewSonic grants you the right to use the Software for use with, and only for use with, bona-fide ViewSonic pen displays. The Software is owned for distribution exclusively by ViewSonic and is protected by the United States Patent and Trademark laws and international treaties. 2. Governing Law, Jurisdiction, and Forum: This Agreement and any questions, claims, disputes, or ● I accept the terms of the License Agreement ○ I do not accept the terms of the License Agreement Next Cancel

Pen Display Manager

Installing...

3) You must reboot the computer after the installation is completed.

Pen Display Manager Pen Display Manager was successfully installed. OK

2.2 Set the display area

Windows 7 and Windows 8 setting environments

Press [Start] icon, open [Control panel], enter into [Display] and select [Adjust resolution], then the setting window will open.

All Control Panel Items ▶ Display ▶ Screen Resolution Search Control Panel Change the appearance of your displays Detect Identify Display: 1. Display device on: VGA Resolution: 1024 × 600 (recommended) Orientation: Landscape Multiple displays: Extend these displays Make this my main display Advanced settings Make text and other items larger or smaller What display settings should I choose? OK Cancel Apply

1) When installing Pen Display device, you will see an additional [Multiple Displays] option.
2) Multiple Displays provides 4 display options:

a. Synchronous display on these displays: mirror display mode, will be changed to main screen and copied screen with same resolution.
b. Extend these displays: extend the display to the right (preset setting).
c. Display the desktop on 1 only: only display the desktop of main screen.
d. Display the desktop on 2 only: only display the desktop of extended screen.

3) Select [Extend these displays], press [OK] and exit.

2.3 Handwriting area correspondence

1) Select the "Image" on the bottom right hand corner to enter the setting.
2) Under "Pen" tab, adjust the tip feel from soft to firm.

Pen Display Properties Pen Mapping Tip Feel Soft Firm Current Pressure: About

3) Under the "Mapping" tab, set the "Orientation" to "Portrait" and "Select the Pen Display" to "2".

Pen Display Properties Pen Mapping Orientation Landscape Select the Pen Display 2 About

4) Close the window to save the changes.

Note: the electromagnetic pen supports multistage pressure. When drawing with pressure, please select one pressure sensing tool from tool palette of the application. When you press the pen tip slightly, the electromagnetic pen will display light-colored or thin line, and when you press the pen tip heavily, the electromagnetic pen will display dark-colored or thick line.

2.4 More touch settings

Windows 7/8 system is equipped with other touch functions. All settings in this chapter are based on this system.

2.4.1 Pen and touch

Click [Start] icon → [Control panel] → [Pen and touch].

Pen and Touch Pen Options Flicks Handwriting ✓ Use flicks to perform common actions quickly and easily ○ Navigational flicks ○ Navigational flicks and editing flicks Customize... Sensitivity You can adjust how easily your flicks are recognized. A more relaxed setting may lead to accidental flicks. Relaxed Precise □ Display flicks icon in the notification area Practice using flicks OK Cancel Apply

a. Handwriting pen option: when operating the items on the screen with electromagnetic pen, you can adjust the action of each electromagnetic pen and the setting of electromagnetic pen button.
b. Flicks: using pen gesture can perform the action quickly and easily with electromagnetic pen on the tablet PC.
c. Handwriting: you can select [Use automatic learning] or [Dont's use automatic learning and delete any previously collected data].

2.4.2 Tablet PC setting

Click [Start] icon → [Control panel] → [Tablet PC setting] → click [Other] tab → click [Go to input panel setting].

Tablet PC Settings Display Other Handedness Change where menus appear on the screen by indicating which hand you write with. Right-handed Menus appear to the left of your hand. Left-handed Menus appear to the right of your hand. Pen and touch Configure your pen and touch settings in Pen and Touch. Go to Pen and Touch Tablet PC Input Panel options Customize Tablet PC Input Panel features in Input Panel Settings. Go to Input Panel Settings OK Cancel Apply

These settings can be used to customize the following input panel functions of tablet PC.

• Handwriting: setting of stroke thickness and writing line spacing.
• Writing-text conversion: handwriting recognition setting.
• Text completion: [Automatic completion] setting and [Predictive text] setting.
  • Advanced: [Action gesture] setting.

3. Troubleshooting

3.1 Screen problems

Problems Recommended actions
No picture * Check whether USB cables at computer end and screen end are connected properly. * Try to use another USB interface of the computer. * Confirm whether the computer is under sleep mode. Press the keyboard or move the mouse, and reboot the system. * Press [Screen] power button and confirm whether the screen is starting up. * Try to adjust the brightness. * Confirm whether the computer is starting up * In case of laptop, please confirm whether the outer-link (RGB) output is selected. * Check whether DisplayLink driver is installed.
Screen completely dark	* Adjust the brightness control. * Long-time operation will decrease backlight efficiency and may affect the screen brightness.
Image noise * Other electrical devices may trigger electrical disturbances.
Image blur * Using the original resolution of 1280 x 800 may provide the optimum quality.

3.2 Problems of interactive electromagnetic pen

Problems Recommended actions
Electromagnetic pen does not work	* Try to confirm by mouse. If the mouse does not work, please reboot the computer or the application.* Try to re-install the driver
Pen tip is too short	* Please check whether the pen tip is too short. If yes, please replace the pen tip.
Abnormal cursor movement	* Remove the disturbances caused by adjacent electrical devices.* Try to reboot the computer to confirm.* Confirm both ends of USB cable are connected to PC.

Note: please don't open the enclosure electric shock hazard. For assistance, please contact local technical support center and/or dealer.

4. Product Specification

4.1 Screen

Display

Model 15.6 inch TFT LCD, LED backlight
Resolution 1366 x 768
Brightness 220 cd/m	^2 (Typ.) / 200 cd/m ^2 (Min)
Angle of visibility Horizontal 90°, vertical 130°
Response time Tr+Tf: 25ms (typical) / 50ms (max.)

Connector

USB USB x1

User control

Control key 1X On/off button, 2X brightness + - button

Power supply

Input AC 100-240V, 50/60HZ

Output DC 12V/2A

Power consumption Start-up 6.5W, sleep < 1.0W

Body

Equipment dimension 390mm x 290mm x 22.35mm
Equipment weight Net weight (no support): 1.88kg
	Net weight (With support): 2.39kg
	total weight: 3.28 kg

Environment

Temperature range Operation: 0°C ~ +40°CStorage: -20°C ~ +65°CRelative humidity Operation: 20% ~ 80%Storage: 10% ~ 90%

4.2 Interactive electromagnetic pen

Model

Technique	Electromagnetic touch
Action area	Full screen

Technical specifications

Resolution 5080 LPI (lines per inch)

Tracking velocity 250 PPS (dots per second)

Pressure sensing Class 2048

Accuracy rating ± 0.5mm (center), ± 2mm (edges and corners)

Readable height 5mm

Electromagnetic pen

Model Pressure sensing,Inclination of detectable pressure sensitive penButton No buttonPen tip Replaceable

wirelessInclination range: ± 45^

Note: The specification is subject to change without prior notice.

5. Appendix

5.1 Replace the pen tip

If the pen tip is too short or exists the sharp edge, it can be replaced to the back-up tip. Please replace according to the following steps:

1) Pull out the pen tip from electromagnetic pen straightly with tool.

2) Insert new pen tip into the handwriting pen and then push in the pen tip until the tip does not move.

Simple line drawing of a pen with an arrow pointing upward (no text or symbols)

Note: The product comes attached with a pen tip replacement tool.

Customer Support

For technical support or product service, see the table below or contact your reseller.

Note : You will need the product serial number.

Country/Region Website	T = TelephoneC = CHAT ONLINE	Email
Australia/New Zealand	www.viewsonic.com.au	AUS= 1800 880 818NZ= 0800 008 822	[e-mail]
Canada www.viewsonic.com	T= 1-866-463-4775 [e-mail]
Europe	www.viewsoniceurope.com	www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong www.hk.viewsonic.com	T= 852 3102 2900 [e-mail]
India www.in.viewsonic.com	T= 1800 266 0101 [e-mail]
Korea www.kr.viewsonic.com	T= 080 333 2131 [e-mail]
Latin America (Argentina)	www.viewsonic.com/la/	C= http://www.viewsonic.com/la/soporte/servicio-tecnico	[e-mail]
Latin America (Chile)	www.viewsonic.com/la/	C= http://www.viewsonic.com/la/soporte/servicio-tecnico	[e-mail]
Latin America (Columbia)	www.viewsonic.com/la/	C= http://www.viewsonic.com/la/soporte/servicio-tecnico	[e-mail]
Latin America (Mexico)	www.viewsonic.com/la/	C= http://www.viewsonic.com/la/soporte/servicio-tecnico	[e-mail]
Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F.Tel: [phone])6547-6484Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico
Latin America (Peru)	www.viewsonic.com/la/	C= http://www.viewsonic.com/la/soporte/servicio-tecnico	[e-mail]
Macau	www.hk.viewsonic.com T= 853 2870 0303 [e-mail]
Middle East	ap.viewsonic.com/me/	Contact your reseller	[e-mail]
Puerto Rico & Virgin Islands	www.viewsonic.com	T= 1-800-688-6688 (English)C= http://www.viewsonic.com/la/soporte/servicio-tecnico	[e-mail]@viewsonic.com
Singapore/Malaysia/Thailand	www.viewsonic.com.sg T= 65 6461 6044 [e-mail]
South Africa	ap.viewsonic.com/za/	Contact your reseller	[e-mail]
United States	www.viewsonic.com T= 1-800-688-6688 [e-mail]

Limited Warranty

VIEWSONIC® PEN DISPLAY

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.

How long the warranty is effective:

ViewSonic Pen Displays are warranted for 1 year for all parts and labor from the date of the first consumer purchase.

Who the warranty protects:

This warranty is valid only for the first consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:

a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Removal or installation of the product.
d. Causes external to the product, such as electrical power fluctuations or failure.
e. Use of supplies or parts not meeting ViewSonic's specifications.
f. Normal wear and tear.
g. Any other cause which does not relate to a product defect.

1. Any product exhibiting a condition commonly known as "image burn-in" which results when a static image is displayed on the product for an extended period of time.
2. Removal, installation, one way transportation, insurance, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to Customer Support page). You will need to provide your product's serial number.
2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and fitness for a particular purpose.

4.3: ViewSonic Digitizer Warranty Page 1 of 2 DIGITIZER_LW01 Rev. 1A 10-24-12

Exclusion of damages:

ViewSonic's liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.

Effect of state law:

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.

The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is subject to the terms and conditions of the Maintenance Guarantee Card.

For users in Europe and Russia, full details of warranty provided can be found in www.viewsoniceurope.com under Support/Warranty Information.

Illustration of three colorful bird perched on a branch against a red background (no text or symbols)

ViewSonic®