AXLOC-CH4 - Kit voiture Metra - Free user manual and instructions

USER MANUAL AXLOC-CH4 Metra

Collection of various electronic components including a black connector, power connector, and cable connectors (no visible text or symbols)

Chrysler LOC (Line Output Converter)

AXLOC-CH4 (for Non-Amplified Vehicles) 2007-2021

Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle specific applications.

• Designed to provide (2) channels of low-level audio output from the factory system.
• Allows for the installation of an amplifier for speakers or subwoofers.
• Gain Controller included to adjust the overall output.
• 12v-500mA remote wire activated with signal sense.
• 55-watts per channel.
• Designed for non-amplified vehicles.

Note: A single pole double throw (SPDT) relay is recommended when installing multiple amplifiers.

APPLICATIONS

Chrysler	Dodge			Jeep
200 2011-2014	Avenger 2008-2014	Dakota	2008-2011	Commander	2008-2010
300 2008-2010	Caliber 2009-2012	Durango	2008-2013	Compass	2009-2017
Aspen 2008-2009	Caravan and	Journey	2009-2010	Grand Cherokee	2008-2013
Sebring 2007-2010	Grand Caravan 2008-2020	Magnum	2008-2009	Liberty 2008-2012
Town & Country 2008-2017	Challenger 2008-2014	RAM	2009-2011	Patriot	2009-2017
	Charger 2008-2010			Wrangler(JK)	2007-2021

For dash disassembly instructions, refer to metraonline.com. Enter the year, make, and model of the vehicle in the Vehicle Fit Guide for Radio Install Kits.

TABLE OF CONTENTS

Applications....1

Installation 2

Diagram 3

TOOLS REQUIRED

• Crimping tool and connectors, or solder gun, solder, and heat shrink
• Tape • Wire cutter • Zip-ties

KIT COMPONENTS

• AXLOC-CH4 Wiring Harness
• Gain Controller
  • 12v-500mA Remote Wire
• Auxiliary Cable

ATTENTION: With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections, especially the air bag indicator lights, are plugged in before reconnecting the battery or cycling the ignition to test this product.

NOTE: Refer also to the instructions included with the aftermarket accessory before installing this device.

INSTALLATION

1. Disconnect the harness from the factory tuner and install the AXLOC-CH4 harness provided with this kit.

2. Mount the gain controller in a suitable location, and connect the auxiliary cable to the BASS KNOB, then to the Gain Connector of the AXLOC harness.

3. Install the aftermarket amplifier and run an RCA pair (sold separately) to the line converter.

4. Connect the remote wire, plug in the device and secure all connections prior to testing.

NOTE: If the vehicle is equipped with active noise cancellation microphones (ANC), it is recommended that they are disabled to prevent potential noise when installing subwoofers.

DIAGRAM

TO RADIO ID-AXLOC-CH4 TO VEHICLE Remote Gain Cont. Aux. Cable NOTE: If using external Bass knob, make sure your "Output Level Adjustment" knob is turned all the way down (turned all the way to the left). Output Level Adjustment Line Out Converter Line Out Converter (Front View) Bass Knob (Top View) Bass Knob (Front View)

REV. 12/2/22 INSTAXLOC-CH4

AXLOC-CH4 INSTALLATION INSTRUCTIONS

Having difficulties? We're here to help.

Contact our Tech Support line at: 386-357-1187

Or via email at: [e-mail]

Tech Support Hours (Eastern Standard Time)

Monday - Friday: 9:00 AM - 7:00 PM

Saturday: 10:00 AM - 7:00 PM

Sunday: 10:00 AM - 4:00 PM

KNOWLEDGE IS POWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

AXLOC-CH4

Collection of various electronic components including connectors, cables, and connectors (no visible text or symbols)