PN-R703 - Écran professionnel SHARP - Free user manual and instructions

USER MANUAL PN-R703 SHARP

To aid reporting in case of loss or theft, please record the products model and serial numbers in the space provided. The numbers are located in the rear of the product.

IMPORTANT INFORMATION WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol, within CAUTION a triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” RISK OF ELECTRIC Within the products enclosure that may be of SHOCK sufficient magnitude to constitute a risk of electric

DO NOT OPEN shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment.

This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This product utilizes a CR coin Lithium battery which contains a Perchlorate material. Special handling for this material may apply,

California residents, See www.dtsc.ca.gov/hazardouswaste/perchlorate/

Others, consult local environmental officers.

DEAR SHARP CUSTOMER Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product.

SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully before using the product.

1. Read instructions — All operating instructions must be read and understood before the product is operated.

2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future

3. Observe warnings — All warnings on the product and in the instructions must be observed closely.

4. Follow instructions — All operating instructions must be followed.

5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.

6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents

7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto it. Be careful of equipment which drains water such as an air-conditioner.

8. Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings. Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.

9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from resting on them.

10. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.

11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.

12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts.

For the same reason, do not spill water or liquid on the product.

13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.

14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service person to perform repairs.

a. When the power cord or plug is damaged.

b. When a liquid was spilled on the product or when objects have fallen into the product.

c. When the product has been exposed to rain or water.

d. When the product does not operate properly as described in the operating instructions. Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified technician

e. When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product needs servicing.

15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.

16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.

17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method recommended by the manufacturer.

18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating products (including amplifiers).

SAFETY PRECAUTIONS (Continued)

19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment, dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:

+ Use the specified batteries only.

- Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the compartment.

+ Do not mix old and new batteries.

+ Do not mix batteries of different types. Voltage specifications of batteries of the same shape may vary.

+ Replace an exhausted battery with a new one promptly.

- If you will not use the remote control for a long time, remove the batteries.

+ Ifleaked battery fluid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your eye well rather than rubbing and seek medical treatment immediately. Leaked battery fluid that gets into your eye or your clothing may cause a skin irritation or damage your eye.

20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury, severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch control in a weapon system.

21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in low-temperature burns.

WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: DVI-D output terminal, DVI- input terminal, PC/AV HDMI input terminal, PC/AV D-SUB input terminal, RS-232C input/output terminals, and DisplayPort input/output terminals.

If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries,

particularly to children, can be avoided by taking simple precautions such as:

+ Using fixing devices like wall mount brackets recommended by the manufacturer.

+ Only using furniture that can safely support the monitor.

+ Ensuring the monitor is not overhanging the edge of the supporting furniture.

+ Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the monitor to a suitable support.

+ Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.

+ Educating children about the dangers of climbing on furniture to reach the monitor or its controls.

Especially for child safety

- Don't allow children to climb on or play with the monitor.

- Don't place the monitor on furniture that can easily be used as steps, such as a chest of drawers.

- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.

- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by curious children

TIPS AND SAFETY INSTRUCTIONS

- The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor.

- Do not display a still picture for a long period, as this could cause a residual image.

- Never rub or tap the monitor with hard objects.

- Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.

- This monitor and its accessories may be upgraded without advance notice.

- Do not use the monitor where there is a lot of dust, where humidity is high, or where the monitor may come into contact With oil or steam, as this could lead to fire.

- Ensure that the monitor does not come into contact with water or other fluids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fire or electric shock.

- Do not place the monitor on top of unstable objects or in unsafe places. Do not allow the monitor to receive strong shocks or to strongly vibrate. Causing the monitor to fall or topple over may damage it.

- Do not use the monitor near heating equipment or in places where there is likelihood of high temperature, as this may lead to generation of excessive heat and outbreak of fire.

- Do not use the monitor in places where it may be exposed to direct sunlight.

- Please be sure to constantly remove dust and garbage that has attached to the ventilation opening. If dust collects in the ventilation opening or the inside of the monitor, it may lead to excessive heat, outbreak of fire, or malfunction.

Please request a cleaning of the inside of the monitor from an authorized SHARP servicing dealer or service center.

- Images cannot be rotated on this monitor.

When using in portrait orientation, you will need to prepare appropriately orientated content in advance.

- The AC outlet shall be installed near the equipment and shall be easily accessible.

- Use only the power cord supplied with the monitor.

- Do not damage the power cord nor place heavy objects on it, stretch it or over bend it. Also, do not add extension cords. Damage to the cord may result in fire or electric shock.

- Do not use the power cord with a power tap.

Adding an extension cord may lead to fire as a result of overheating

- Do not remove or insert the power plug with wet hands. Doing so could result in electric shock.

- Unplug the power cord if it is not used for a long time.

- Do not attempt to repair the power cord if it is broken or malfunctioning. Refer the servicing to the service representative.

- Microsoft, Windows and Internet Explorer are registered trademarks of Microsoft Corporation.

- The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

- DisplayPort is a registered trademark of Video Electronics Standards Association.

- Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

- This product comes with RICOH Bitmap Fonts produced and sold by RICOH COMPANY, LTD.

- All other brand and product names are trademarks or registered trademarks of their respective holders.

- Language of OSD menu used in this manual is English by way of example.

- Illustrations in this manual may not exactly represent the actual product or display.

- This manual assumes use in landscape orientation, except where specifically noted.

+ The LED backlight in this product has a limited lifetime.

* Ifthe screen gets dark or does not turn on, it may be necessary to replace the LED backlight.

* This LED backlight is exclusive to this product and must be replaced by an authorized SHARP servicing dealer or service center. Please contact an authorized SHARP servicing dealer or service center for assistance.

MOUNTING PRECAUTIONS

+_ This product is for use indoors.

+ A mounting bracket compliant with VESA specifications is required.

+ Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor.

+ Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or mishandling.

+ Use the monitor with the surface perpendicular to a level surface. If necessary, the monitor may be tilted up to 20 degrees upward or downward.

+_ This monitor should be used at an ambient temperature between 32°F (0°C) and 104°F (40°C). Provide enough space around the monitor to prevent heat from accumulating inside.

For the monitor in landscape orientation Unit inch [mm] ÉLCIUME

For the monitor in portrait orientation

Unit inch [mm] 7-7/8 1200] 576 [7] 12 | 2. 150] l [Power LED 12150] 2

+_Ifitis difficult to provide sufficient space for any reason such as the installation of the monitor inside a housing, or if the ambient temperature may be outside of the range of 32°F (0°C) to 104°F (40°C), install a fan or take other measures to keep the ambient temperature within the required range.

+_ Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such cases, please check the temperature condition specified by the optional equipments.

+ Do not block any ventilation openings. If the temperature inside the monitor rises, this could lead to a malfunction.

+ Do not place the monitor on a device which generates heat.

Adhere to the following when installing the monitor in its portrait orientation. Failing to adhere to the following may cause malfunctions.

- Install the monitor such that the power LED is located on the bottom side.

- Setthe MONITOR on the MONITOR menu to PORTRAIT. (See page 26.)

- Be sure to clamp the power cord (supplied) onto the cable clamp attachment using the supplied cable clamp. When clamping the power cord, take care not to stress the terminal of the power cord. Do not bend the power cord excessively.

Power cord (Supplied) Cable clamp attachment

Use the supplied vertical sticker when you install the monitor in portrait orientation

L Cover SHARP logo SHARE-— Logo

Do not remove the factory-affixed sticker but affix the sticker over it. Be careful not to cover the remote control sensor or buttons.

IMPORTANT INFORMATION DEAR SHARP CUSTOMER. SAFETY PRECAUTIONS... TIPS AND SAFETY INSTRUCTIONS MOUNTING PRECAUTIONS Supplied Components. Part Names .… Connecting Peripheral Equipment: Connection with a PC or AV equipment. Connecting the Power Cord Binding Cables. Preparing the Remote Control Uni Installing the batteries Remote control operation range. Turning Power On/Off Turning on the main power. Turning power on/off Disabling power on/off operations Basic Operation . Menu Items Displaying the menu screen Menu item details nn Adjustments for PC screen display

Initialization (Reset)/Functional Restriction Setting (FUNCTION) Controlling the Monitor with a PC (RS-232C). PC connection. Communication conditions Communication procedure Setting of the GAMMA user data RS-232C command table Controlling the Monitor with a PC (LAN). Settings to connect to a LAN. Controlling with a PC... [Advanced operation] Command-based control. Troubleshooting Specifications Mounting Precautions (For SHARP dealers and service engineers

If any component should be missing, please contact your dealer.

O Liquid Crystal Display Monitor: 1 [ Remote control unit: 1 D Cable clamp: 2 D Cable clamp (stick-on): 2 O Power cord: 1 O1 R-6 battery (‘AA’ size): 2 [1 CD-ROM (Utility Disk for Windows): 1 D Setup Manual: 1 © Vertical sticker (Logo): 1 © Vertical sticker (Operation panel): 1 D Cover SHARP logo: 1 Place this sticker onto the SHARP logo to cover the logo.

*_ SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.

* For environmental protection!

Do not dispose of batteries in household waste. Follow the disposal instructions for your area.

Accessing the operation panel

+ Use a pointed object such as a pen tip to press the switches.

+ Consult your SHARP dealer for attachment/detachment of optional parts.

. Power LED (See page 16.)

. Optional attachment section

This section is used to connect optional hardware for function expansion. Offering this attachment location is not a guarantee that future compatible hardware attachments will be released.

This terminal is provided for possible future (optional) function expansion. Offering of this terminal is not a guarantee that future expanded functionality will be provided.

Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected.

Be careful not to confuse the input terminal with the output terminal when connecting cables. Accidentally reversing cables connected to the input and output terminals may cause malfunctions and the other problems.

Do not use any cable that has a damaged or deformed terminal. Using such cables may cause malfunctions.

TIPS Images may not be displayed properly depending on the computer (video card) to be connected.

Use the automatic screen adjustment when a PC screen is displayed for the first time using D-SUB[RGB] or DVI-I (analog), or when the setting of the PC is changed. The screen is adjusted automatically when SELF ADJUST in the MONITOR menu is set to ON.

If the audio output from the playback device is connected directly to speakers or other devices, the video on the monitor may appear delayed from the audio portion. Audio should be played through this monitor by connecting the playback device to the monitor's audio input, and connecting the monitor's audio output to the speakers or other devices.

The audio input terminals used in each input mode are factory-set as follows.

Connection with a PC or AV equipment

Use a commercially available DisplayPort cable.

When DisplayPort is selected, connection to the audio input terminal is unnecessary.

DVI-! input terminal

Use a commercially available signal cable (DVI-1 29 pin). Select the audio input terminal to be used in DVI-I of AUDIO SELECT on the SETUP menu.

If the display is not shown properly, set EDID SELECT {DVI-1) of INPUT SELECT on the SETUP menu according to the device to be connected

Use a commercially available HDMI cable (conforming to the HDMI standard).

Set HDMI or HDMI2 of INPUT SELECT on the SETUP menu according to the device to be connected.

Select the audio input terminal to be used in HDMI1[AV], HDM11[PC], HDMI2[AV] or HDMI2[PC] of AUDIO SELECT on the SETUP menu.

When HDMI is selected, connection to the audio input terminal is unnecessary.

PC/AV D-sub input terminal

Set D-SUB of INPUT SELECT on the SETUP menu according to the device to be connected.

To use with D-SUB[VIDEO)], connect the green terminal to the device's video output.

Select the audio input terminal to be used in D-SUB[RGB], D-SUBICOMPONENT] or D-SUB[VIDEO] of AUDIO SELECT on the SETUP menu.

Audiol input terminal

Use an audio cable without resistance.

Set the audio input terminal to be used in each input mode in AUDIO SELECT on the SETUP menu.

Connecting Peripheral Equipment

8. DisplayPort output terminal

+ _ The video of the DisplayPort input can be output to an external device

+ _ Use a commercially available DisplayPort cable.

+ Outputting HDCP-encrypted video requires an external device which supports HDCP.

+_ This terminal allows the daisy chain connection (up to 25 monitors or up to 4 monitors when transmitting HDCP- encoded content) by connecting the monitors to each other through the DisplayPort input terminal of each monitor.

DVI-D output terminal

+ _ The video of the DVI-I (digital) input can be output to an external device

+ Outputting HDCP-encrypted video requires an external device which supports HDCP.

+_ This terminal allows the daisy chain connection of up

to 5 monitors by connecting the monitors to each other

through the DVI-I input terminal of each monitor.

The length of the signal cables or surrounding environment may affect the image quality.

The output screen may not display properly when using terminals other than DVI-I for the input mode. In this case, turn off the power to all the monitors connected in a daisy chain and then turn the power on again.

When connecting monitors in a daisy chain set AUTO INPUT CHANGE to OFF.

Video output is disabled in the following cases:

When the power is turned off

When the monitor is in input signal waiting mode

10. Audio output terminal

+ _ The output sound varies depending on the input mode. + _ The volume of the output sound can be fixed by setting AUDIO OUTPUT of AUDIO OPTION on the SETUP

menu. +_Itis not possible to control the sound output from the audio output terminals with the AUDIO menu.

11. RS-232C output terminal 12. RS-232C input terminal

+ You can control the monitor from a PC by connecting a commercially available RS-232 straight cable between these terminals and the PC

+ You can control the monitor from a PC on a network by connecting a commercially available LAN cable between this terminal and a network.

Connecting the Power Cord

+ Use only the power cord supplied with the monitor.

1. Turn off the main power switch.

2. Plug the power cord (supplied) into the AC input terminal.

3. Plug the power cord (supplied) into the AC power outlet.

Power cord (Supplied) (IL 2

The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp.

Insert the cable clamp into the cable clamp attachment on the rear of the monitor and fasten the cables.

Cable clamp attachment

Use the supplied cable clamp (stick-on) affixed to the rear ofthe monitor.

Where you attach the cable clamp, please remove the dirt.

* Do not cover the vents.

Preparing the Remote Control Unit

Installing the batteries

1. Press the cover genitly and slide it in the direction of the arrow.

2. See the instructions in the compartment and put in the supplied batteries (R-6 (‘AA size) x 2) with their plus (+) and minus (-) sides oriented correctly. 3. Close the cover.

+ When the batteries become exhausted, replace them with new (commercially available) batteries.

+ The supplied batteries (R-6 (‘AA” size) x 2) may become exhausted quickly depending on how they are stored. +_ If you will not be using the remote control for a long time, remove the batteries.

+ Use manganese or alkaline batteries only.

Remote control operation range

The remote control can be operated even when the operation panel is stored inside the monitor.

Point the remote control toward the remote control sensor on the bottom of the monitor (or the right side of the monitor if using portrait orientation).

For the monitor in landscape orientation For the monitor in portrait orientation

dl Remote control sensor 1 16.4 feet (5m)

Point the remote control toward the remote control sensor on the front of the monitor. For the monitor in landscape orientation For the monitor in portrait orientation

! Remote control sensor 16.4 feet ; (5m)

+ Do not expose the remote control unit to shock by dropping or stepping on it. This could lead to a malfunction.

+ Do not expose the remote control unit to liquids, and do not place it in an area with high humidity.

+ _ The remote control unit may not work properly if the remote control sensor is under direct sunlight or strong lighting. + Objects between the remote control unit and the remote control sensor may prevent proper operation.

+ _Replace the batteries when they run low as this may shorten the remote control's operation range.

+_Ifa fluorescent light is illuminated near the remote control unit, it may interfere with proper operation.

+ Do not use it with the remote control of other equipment such as air conditioner, stereo components, etc.

Turning Power On/Off

+ Turn on the monitor first before turning on the PC or playback device.

Turning on the main power

+ The main power must be turned on/off with the main power switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch is on.

+ When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds.

+ For a complete electrical disconnection, pull out the main plug.

Turning power on/off

Press the POWER button or POWER switch to turn the power ON/OFF.

Power switch Power LED Status Status of the monitor Green lit Power on Orange lit Power off (Standby mode)

Green flashing Input signal waiting mode

Itis possible to check the power LED even when the operation panel is stored inside the monitor.

+ _ When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. A short interval may result in a malfunction.

+ _ When the main power switch is off, the monitor cannot be turned on.

+ _Ifthe monitor is in the input signal standby mode and you

press the POWER button on the remote control unit, the

monitor enters standby mode.

Setting the SCHEDULE flashes the power LED alternately

in red and orange in standby mode.

To disable the logo screen from displaying when turning the

power ON, set LOGO SCREEN to OFF on the OTHERS

menu. (See page 28.)

+_lfthe time has yet to be set when the monitor is first turned on, the date/time setting screen appears. Set the date and time.

DATE/TIME SETTING CCE E:©

OK-ENTER] CANCEL--{RETURN]

1. Press C% or to selectthe date and time, and press =) or to change the numerical values.

+ Be sure to set the date and time.

+ The date/time setting screen will close automatically if no operation is performed for about 15 seconds. The date and time can be set using DATE/TIME SETTING from the SETUP menu when the date/time setting screen disappears.

+ Set the date in “Month/Day/Year” order.

+ Set the time on a 12-hour basis.

+ The clock is maintained by the internal battery.

*_lf you already set the time but the date/time setting screen appears when the power is turned on, the internal battery may be exhausted. Please contact an authorized SHARP servicing dealer or service center for assistance with battery replacement.

+ Estimated service life of the internal battery: About 5 years (depending on monitor operation)

* Theinitial battery was inserted at the factory when the monitor was shipped, so it may run out of power before its expected operation life.

Turning Power On/Off

Disabling power on/off operations

Power on/power off operations can be disabled in order to protect the monitor from an accidental power off. Set the ADJUSTMENT LOCK in FUNCTION menu to “ON 2”. (See page 32.)

1. INPUT (Input mode selection) The menu is displayed. Press d or es] to selectthe input

mode, and press (5 to enter. *_ You can select the input terminal by pressing the input

switch of the monitor.

Input mode Video Audio DVI DVI: input terminal DisplayPort DisplayPort input terminal HDMH{PC] PC/AV HDMI input HDMIH{AVI terminal" HDMI2PC] PC/AV HDMI2 input “ HDMI2AV] terminal? D-SUBIRGE] D-SUBICOMPONENT] oies input D-SUBIVIDEO]

Select the terminal to be used in HDMI1 of INPUT SELECT. (See page 24.)

Select the terminal to be used in HDMI2 of INPUT SELECT. (See page 24.)

#3 Selectthe terminal to be used in D-SUB of INPUT SELECT. (See page 24.)

*4 Select the terminal for AUDIO SELECT which is used for

audio input. (See page 24.)

2. MUTE Turns off the volume temporarily.

Press the MUTE button again to turn the sound back to the previous level.

3. MENU Displays and turns off the menu screen. (see page 20.)

4. VOL +/- (Volume adjustment)

Press (À or C7 to adjust the volume of the sound. *_ If you do not press any buttons for about 4 seconds, the VOLUME menu automatically disappears.

5. BRIGHT +/- (Brightness adjustment)

Pressing =) or displays the BRIGHT menu when the menu screen is not displayed.

Press ==) or > to adjust the brightness. *_If you do not press any buttons for about 4 seconds, the BRIGHT menu automatically disappears.

6. ENTER Confirms the setting.

7. RETURN Returns to the previous screen

8. SIZE (Screen size selection) The menu is displayed. Press (_)orC to select the screen size. (See page 19.)

9. DISPLAY Displays monitor information.

The display changes from INFORMATION —+

INFORMATION? — clear display, and so on every time you

+ _ The display disappears automatically after about 15 seconds.

is displayed during LAN communication.

is displayed in red, there is a duplicate IP address.

10. MODE (Color mode selection) Each time you press this button, the color mode changes in the following order:

STD (Standard) —> VIVID — sRGB — HIGH ILLUMINANCE — STD...

+ HIGH ILLUMINANCE is a display with colors suited to bright locations.

+ _SRGB applies to PC input only. SRGB is international standard of color representation specified by IEC (International Electrotechnical Commission). Color conversion is made in taking account of liquid crystal's characteristics and represents color tone close to its original image.

#Switching the screen size Even when the screen size is changed, the display may remain the same depending on the input signal.

WIDE re} © PC input Displays image so it fills the entire screen. CO AV input An image with a 4:3 aspect ratio is stretched to fill the entire (e] el] screen. ZOOM 1 PC input An image with a 4:3 aspect ratio is enlarged to fill the entire screen without changing the aspect ratio. The edges of the image may be n cut off. AV input ZOOM2 PC input Use this size if ZOOM 1 cuts off the subtitles. O AV input Q O NORMAL Oo o PC input Displays image so it fills the screen without changing the aspect ratio of the input signals O AV input Displays the entire image of the aspect ratio of 4:3 without O O changing the aspect ratio. Dot by Dot PC input Displays the dots of the signals input from the connected PC as © © the corresponding dots on the screen. o O o AV input Displays the dots of the input signals as the corresponding dots on

TIPS Using this monitor's screen-size switching or dual-screen display functions to compress or expand the screen for commercial or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright Law, so please be careful.

When “Enlarge” is set, the screen size is fixed to “WIDE” mode.

When dual-screen display is selected, the screen size cannot be changed.

The appearance of the original video may change if you select a screen size with a different aspect ratio than the original image (e.g. TV broadcast or video input from external equipment).

When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator's intentions, set the screen size to “NORMAL”.

When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the edges of the screen. This is due to the characteristics of the software, and is not a malfunction.

Depending on the original image size, black bands may remain at the edges of the screen.

Displaying the menu screen

Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 20 to 29 for details of each menu items.

+ Do not turn the main power switch off while the menu items are being displayed. Doing so may initialize the settings.

mE xample of operation (Adjusting CONTRAST in the PICTURE menu) 1. Press CS to display the menu screen.

LOR ADJUSTMENT JANCÉD Fessfu

For items that have D , press es, make settings and RETURN

+ _ The menu screen will close automatically if no operation is performed for about 15 seconds. (DATE/TIME SETTING, SCHEDULE and LAN SETUP screens will close in about 4 minutes.)

3 Anitem being selected (highlighted)

4 Screen resolution of input signal, and other data.

+_ Items that cannot be selected appear in gray. (e.g. Function not supported by the current input signal)

The menu will differ depending on the input mode.

HSCREEN You can move the menu screen display position each time (7 is pressed.

AUTO (D-SUB[RGB]J/DVI-I (analog)) TheC LOCK, PHASE, H-POS, and V-POS are automatically adjusted.

Pressing C_) performs adjustment. Use this automatic adjustment when you use the D-SUB[RGB] or DVI-I (analog) to display a PC screen for the first time or when you change the setting of the PC. (See page 31.)

CLOCK (D-SUB[RGB J/DVI-I (analog))

Adjusts frequency for sampling clock for applicable video.

Adjust when there is flickering in the form of vertical stripes.

When using the adjustment pattern (see page 31), make adjustments so that no vertical stripe noise appears in it.

PHASE (D-SUB[RGB J/DVI-I (analog))

Adjusts sampling clock phase for applicable video. Useful when small characters appear with low contrast and/or there are flickers at corners. When using the adjustment pattern (see page 31), make adjustments so that no horizontal stripe noise appears in it.

*_Adjustments to PHASE should be made only after CLOCK has been correctly set.

H-POS Adjust the horizontal position of the image.

v-POS Adjust the vertical position of the image.

H-SIZE Adjust the horizontal size of the image.

V-SIZE Adjust the vertical size of the image.

RESOLUTION SETTING (D-SUB[RGBJ/DVI-I (analog))

H-RESOLUTION Sets proper horizontal resolution when the resolution of input signals is not recognized properly. (Adjustment may be impossible with some signals.)

V-RESOLUTION Sets proper vertical resolution when the resolution of input signals is not recognized properly. (Adjustment may be impossible with some signals.)

RESET Resets the values of the SCREEN menu items to the factory preset values. Select “ON” and then press (7.

MPICTURE You can move the menu screen display position each time (77) is pressed.

BRIGHT Adjusts the backlight brightness. (In PIP mode, the main side setting is reflected in the image.)

CONTRAST Adjusts the difference between the bright and dark portions of the image.

BLACK LEVEL Adjusts the entire brightness of the video signals.

TINT Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta.

COLORS Adjusts the color intensity.

SHARPNESS Adjusts the sharpness of the image.

COLOR ADJ USTMENT COLOR MODE Changes the color mode on the screen. The color mode on the screen can also be changed using a remote control unit. (See page 18.) * SRGB is PC input only. See page 18 for details. {In PIP mode, the main side setting is reflected in the image.) WHITE BALANCE THRU. Displays the input signal level as is. (for PC input only) PRESE Selects the color temperature using PRESET. USER. Used for adjusting R-/G-/B-CONTRAST and R-/G-/B-OFFSET respectively. {In PIP mode, the main side setting is reflected in the image.) PRESET Selects the color temperature when the WHITE BALANCE is set to PRESET. The setting values are shown for reference. The color temperature of the screen varies over time. This function is not intended to keep the color temperature constant. USER Adjusts each item when the WHITE BALANCE is set to USER. R-CONTRAST.... Adjusts bright-toned red component. G-CONTRAST … Adjusts bright-toned green component. B-CONTRAST.... Adjusts bright-toned blue component. R-OFFSET …... Adjusts dark-toned red component. G-OFFSET.. Adjusts dark-toned green component. B-OFFSET.. Adjusts dark-toned blue component. COPY TO USER Copies the value of white set for PRESET to the USER setting. Select "ON” and then press C5. (In the case other than white, color tone may differ from the PRESET.) GAMMA Selects the gamma. USER sets the gamma to the sent value (see page 36). (In PIP mode, the main side setting is reflected in the image.) FLESH TONE (AV input] Adjust the hue control. When FLESH TONE is set to LOW or HIGH, C.M.S.-HUE/-SATURATION/-VALUE cannot be set.

C.M.S.-HUE (AV input) Adjusts color tone with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta). C.M.S.-SATURATION (AV input

Adjusts color vividness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).

C.M:S.-VALUE (AV input] Adjusts color brightness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).

ADVANCED AUTO (D-SUB[RGB J/DVI-I (analoq)) The ANALOG GAIN and ANALOG OFFSET are automatically adjusted. Pressing [=) performs adjustment.

ANALOG GAIN (D-SUB[RGB J/DVI-I (analoq)) Adjusts the bright portions of the video input signal.

ANALOG OFFSET (D-SUB[RGB J/DVI-I (analog)) Adjusts the dark portions of the video input signal. 3D-NR (AV input) Reduce the noise of playback images on video. Setting a higher level reduces more noise. However, it may cause blurring on an image.

MPEG-NR (AV input Reduce block noise caused by digital compression. 3D-Y/C (D-SUB[VIDEO Specify whether to perform 3-dimension Y/C separation. If dot interference or cross-color is occurring in fast-motion scenes, selecting “OFF” may improve the image quality. RGB INPUT RANGE (DVI-I/HDMI[PCJ/HDMI[AV]/D-SUB[RGB]DisplayPort) Sets the RGB input signal range. When using HDMI or DisplayPort set to AUTO, the RGB input signal is detected automatically. Use AUTO normally. If the RGB input signal range cannot be set appropriately even when using AUTO, set according to the image. When the setting is different, images will be displayed with washed out blacks and compressed gradients. ACTIVE CONTRAST (AV input) Automatically adjusts the contrast according to the image. (In PIP mode, the main side setting is reflected in the image.) The adjustment operation may not be smooth depending on the image. In this case select OFF.

DISPLAY COLOR PATTERN Displays a color pattern. Can be displayed while the menu screen is displayed, so you can refer to the pattern while adjusting the image.

..No pattern display. .. White single color pattern display.

USER ..Red/green/blue mixed color pattern display. When USER is selected, set each color's level.

HAUDIO TREBLE Adjusts the volume of treble-level sound.

BASS Adjusts the volume of bass-level sound.

BALANCE Adjusts the balance of the audio sound between right and left.

RESET Resets the values of the AUDIO menu items to the factory preset values.

Select "ON” and then press €.

mSETUP DATE/TIME SETTING Setthe date and time. Press C2) or (to select the date and time, and press Cor C5 to change the numerical values Set the date in “Month/Day/Year” order. Set the time on a 12-hour basis. (Factory default)

DATE/TIME FORMAT Sets the date/time display format.

DATE MM/DD/YYYY, DD/MM/YYYY, YYYY/MM/DD (YYYY: Year, MM: Month, DD: Day) TIME... Select 12- or 24-hour time.

SCHEDULE (See page 30.) You can turn the power on/off and change the screen brightness at a specified time.

LANGUAGE Sets the display language for the menu screen.

INPUT SELECT HDMI1/HDMI2 Select the input mode to be used in PC/AV HDMI and PC/AV HDMI2 input terminals. D-SUB Select the input mode to be used in PC/AV D-Sub input terminal. Select SET after selecting the input mode, and then press

HDMI AUTO VIEW When ON is selected, the screen size is adjusted automatically according to the screen size control signal included in the video signal input from the AV HDMI input terminal.

HOT PLUG CONTROL Sets whether to use hot plug control for the DVI-1, PC/AV HDM11, and PC/AV HDMI2 input terminals. EDID SELECT (DVI-1

Normally, leave this setting as AUTO.

If the display is not shown properly, change the setting according to the connected device.

AUDIO SELECT Selects the terminal used to input audio signals in each input mode.

AUDIO OPTION AUDIO OUTPUT Sets the volume of sound output from the audio output terminals. When set to VARIABLE 2, sound will not be output from the built-in speaker.

VARIABLE1. You can adjust the volume using VOLUME. VARIABLE2. You can adjust the volume using VOLUME. FIXED. Fixes the sounds.

AUDIO INPUT LEVEL 1/2 Selects the maximum audio input level of the audio input 1, 2 terminals.

MONAURAL AUDIO Outputs audio signals as monaural.

COMMUNICATION SETTING RS-232C/LAN SELECT Selects the method with which to control the monitor from the computer. BAUD RATE Selects the communication speed used for RS-232C communication LAN SETUP Configures the settings to control the monitor from the computer via LAN. (See page 45.) AUTO ASSIGN FIXED IP ADDR. Can be enabled when RS-232C/LAN SELECT is LAN and the DHCP CLIENT is OFF. Set DHCP CLIENT to OFF for the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows. Fixed IP addresses are automatically allocated. If the IP address is a duplicate with a network device other than a monitor, individually change the IP address.

ID SETTING ID No. SET Assigns ID numbers to monitors connected in a daisy chain (see page 34), using the RS-232 cables. The numbers 1 to 255 are available for ID numbers. If “0” is set, the system regards this as the state where no ID number is set.

AUTO ASSIGN ID No. ID No. to be used will be automatically assigned when multiple monitors are connected with RS-232C. Select ON, then press €). Perform operations using the first monitor in the daisy chain.

COPY SETTING VALUE When the monitor has been connected to multiple monitors by RS-232C, the settings in the monitor can be copied to the monitor connected to the RS-232C output terminal and to the daisy chain of connected monitors that follows.

Selects the settings to copy with COPY SETTING VALUE TARGET.

“PICTURE"ONLY …... Copies the PICTURE menu settings.*

ALL .. Copies all the settings.*

Select the ID No. of the monitor that you would like copy to with COPY TO ID No. then select COPY and press es.

If you select ALL, settings will be copied to all monitors.

When you would like to confirm the ID No. that is set to the monitor, select ID No. DISPLAY and press (5. The ID No. will be displayed on the screen.

* Certain setting details such as ANALOG GAIN, ANALOG OFFSET, and DISPLAY COLOR PATTERN cannot be copied.

OSD V-POSITION Adjusts the vertical display position of menu screen.

STANDBY MODE When STANDARD is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed in standby mode.

When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the startup time from standby mode becomes longer.

If set to LOW POWER, certain RS-232C commands cannot be used in standby mode, and control via LAN will be disabled.

OFF IF NO OPERATION Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit, RS-232C commands, or LAN for over 4 hours.

POWER ON DELAY If SET is set to ON, you can delay the screen display after the monitor is turned on. When ON is selected, set the delay time with INTERVAL (interval can be set up to 60 seconds in units of 1 second). When this function is activated, the power LED flashes (at approx. 1 second interval) in orange.

SELF ADJUST On a D-SUB[RGBJ/DVI-I (analog) screen, specify whether to perform screen adjustment automatically or not.

When ON is selected, the screen is automatically adjusted when its resolution is 800 x 600 or higher and the timing of input signals changes. “ADJUSTING” appears on the screen during the adjustment.

1f SELF ADJUST is set to ON, set the time it takes to start the SELF ADJUST function in START TIMING.

For images with black edges, etc., depending on the signal, adjustment may not be possible. In this case select OFF. (Perform manual adjustment of the screen.)

ADVANCED (BEZEL AD] UST. BEZEL ADJUST (TOP) / BEZEL ADJUST (BOTTOM) /BEZEL ADJUST (RIGHT) / BEZEL ADJUST (LEFT) ee Adjusts so that the top/bottom/left/right connecting joints of grouped units will be displayed smoothly when a group of monitors are aligned in multiples to display a single image. BEZEL (TOP) / BEZEL (BOTTOM) / BEZEL (RIGHT) / BEZEL (LEFT) es Sets the frame width of the display.

PIP/PbyP PIP MODES Sets the display method. Displays one screen. Displays a sub screen inside a main screen. Displays a main screen and a sub screen in a line. Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line.

PIP SIZE Sets the size of the sub screen in PIP mode.

PIP H-POS Adjusts the horizontal position of the sub screen in PIP mode.

PIP V-POS Adjusts the vertical position of the sub screen in PIP mode.

PIP BLEND In PIP mode, use this menu item to display the sub screen transparently.

PIP SOURCE Selects the input signal of the sub screen in PIP, PbyP, or PbyP2 mode.

SOUND CHANGE Sets the sound which is output in PIP, PbyP, or PbyP2 mode. If the main screen is displayed as a full screen by the AUTO OFF function, the sound for the main screen is output even when the sound for the sub screen is specified. MAIN POS Sets the position of the main screen in PbyP or PbyP2 mode. PbyP2 POS Sets the position of the sub screen in PbyP2 mode. AUTO OFF Sets the display method when no signals for the sub screen are input in PIP, PbyP, or PbyP2 mode. MANUAL …... Displays a main screen and a black sub screen. AUTO Displays the main screen as a full screen.

ROTHERS SCREEN MOTION PATTERN Residual i images are reduced by moving the screen.

OFFSCREEN MOTION function is disabled

PATTERN... The whole screen moves vertically and horizontally.

PATTERN2A black screen spreads from the bottom of the screen and then shrinks to the bottom of the screen. Ifthe monitor is installed in the portrait orientation, a black screen spreads from the left end of the screen and then shrinks to the left end of the screen.

PATTERN3A black bar moves from the left end to the right end of the screen. If the monitor is installed in the portrait orientation, a black bar moves from the top to the bottom of the screen.

PATTERN4Black screens appear from both the top and bottom of the screen, and the displayed image is compressed into the central field. If the monitor is installed in the portrait orientation, the screen is compressed from the left and right ends

PATTERNI PATTERN2 PATTERN3 PATTERN4 v sr t < ti

MOTION TIME 1 Specify a time period (operating interval) until SCREEN MOTION starts. MOTION TIME 2 Specify a time period during which SCREEN MOTION operates (time period during which the screen will move).

POWER MANAGEMENT POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal standby mode.

AUTO INPUT CHANGE Specify whether to change inputs automatically. When ON is selected and no signal is present in the selected input mode, AUTO INPUT CHANGE automatically changes the selected mode to another mode where a video signal is present. When video signals exist in multiple input modes, the switching priority is as follows:

DVHI, DisplayPort, HDMI1, HDMI2, D-SUB

(Input mode switching may take 15 seconds or more, depending on the connected equipment. Input signals may not be detected properly and a priority may change, depending on the connected equipment or video signals.)

LOGO SCREEN Sets whether or not to display the logo screen.

INPUT SIGNAL (D-SUB[RGB]J/DVI-I (analog))

If a computer connected to the D-SUB[RGBJ/DVI-I (analog) outputs any of the following resolutions, make a selection from the following options.

* Even when MODE 1 is selected, under-scan display is used when the input signal is 1080i/p and the screen size is Dot by Dot.

COLOR SYSTEM (D-SUB[VIDEO])

Select the color system of the AV equipment which is connected to PC/AV D-sub input terminal. (AUTO / PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43) When AUTO is selected, the color system is automatically set according to the input signal.

+ When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST, TINT, COLORS, RGB INPUT RANGE, GAMMA and COPY TO USER cannot be set.

+ If COLOR MODE is set to SRGB, the following items cannot be set.

WHITE BALANCE, PRESET, USER, COPY TO USER, and GAMMA When the COLOR MODE is set to VIVID or HIGH ILLUMINANCE, GAMMA can not be adjusted.

STANDBY MODE cannot be set to LOW POWER when SCHEDULE is effective.

When displaying the color pattern, it is possible to adjust certain items of the PICTURE menu.

Non-adjustable items cannot be selected.

Audio input from the HDMI input terminal is also not output.

mDual screen display

You can display two screens simultaneously. Set this function with PIP MODES of PIP/PbyP in the MULTI/ PIP menu.

PIP A sub screen is displayed Main screen inside a main screen.

PbyP A main screen and a sub screen are displayed in a line.

PbyP2 Displays a main screen

which measures 1280 pixels in the longest direction and a sub screen in a line.

The currently selected input signal is displayed on the main screen. The following combinations are available for display: DisplayPort - HDMI or HDMI2 DisplayPort - D-SUB[RGB] DisplayPort - D-SUB[COMPONENT] DisplayPort - D-SUB[VIDEO] DVI-1 - HDMI or HDMI2 DVI-1- D-SUBICOMPONENT] DVI-1- D-SUB[VIDEO]

TIPS You might infringe on a copyright of the author which is protected by copyright law when you display the images of the computer screen and television/VCR simultaneously for profit-making or to show the image to the public.

The screen size for dual-screen display is the same as

the screen size for single-screen display. The Dot by Dot screen is displayed in NORMAL size except when it is set as the PIP main screen.

When dual-screen display is selected, the SCREEN MOTION function is disabled.

When dual-screen display is selected, the AUTO INPUT CHANGE function is disabled

When dual-screen display is selected, the screen cannot be enlarged.

When dual-screen display is selected, the INPUT SELECT options cannot be set.

When an interlaced signal (1080i, 480i, video) is input to the sub screen, horizontal lines may flicker. If this happens, display the image on the main screen.

BEnlarge + You can align several monitors and integrate them into a single large screen to display.

+ Up to 5 monitors can be aligned in both the horizontal and vertical directions.

+ Each monitor displays enlarged views of separated images. (Example) Horizontal direction: 2 monitors Vertical direction: 2 monitors

Horizontal direction: 3 monitors Vertical direction: 2 monitors

2. Select ADVANCED (ENLARGE).

3. Set the number of monitors aligned in the horizontal direction in ENLARGE H.

4, Set the number of monitors aligned in the vertical direction in ENLARGE V.

5. Set the section of the separated image to be displayed on each monitor in ENLARGE-POS.

1) Press F5. 2) Press (À, C7, Cor to select position, then

+ When Enlarge is used, the SCREEN MOTION function is disabled.

+ When Enlarge is used, the AUTO INPUT CHANGE function is disabled

+ When Enlarge is used, the HDMI AUTO VIEW function is disabled.

mZ0OM2 SPECIAL SETTING If you connect a laptop computer with any of the following screen resolutions and black bands appear around the screen, set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on the OTHERS menu to ON and then select ZOOM2 in the SIZE setting

This displays the area inside the black band.

Laptop computer | Corresponding signal*!

1280x800 1280x1024, 1280x960, 1400x1050*2 1280x600 1280x720

“1: This setting is effective only when the screen resolution, including the black band, is one of the resolutions listed above.

“2: Use the automatic screen adjustment.

MSCHEDULE You can set the time to switch the monitor on and off.

2. Setthe SCHEDULE. (See the description below.)

PRIS ; PE Press Cjorc to select items, and press or c to change the setting.

3. Press (5. SCHEDULE becomes effective.

Q) e: SCHEDULE effective —: SCHEDULE not effective

(2) POWER ON : Switches the monitor on at the specified time. OFF : Switches the monitor off at the specified time and puts the monitor in standby mode.

(3) DAY OF THE WEEK Specifies the day of the week to execute the SCHEDULE. O:ONLY ONCE Executes the SCHEDULE once on the specified day. Specify the day of the week to execute the SCHEDULE. EVERY WEEK Executes the SCHEDULE on the specified day of the week every week. Specify the day of the week to execute the SCHEDULE. Periodic setting such as “Monday through Friday” is also possible. 2:EVERY DAY Executes the SCHEDULE every day regardiess of the day of the week.

(4) TIME Specifies the time to execute the SCHEDULE.

Set the time on a 12-hour basis. (Factory default)

Can be entered as 24-hour time using the TIME setting in DATE/TIME FORMAT.

(5) INPUT Specifies the input mode at power-on. |f you don't specify this the input active at the last power-off will appear. Input modes displayed on HDMI1, HDMI2 and D-SUB will depend upon the INPUT SELECT settings

(6) BRIGHT Sets the brightness when changing the screen brightness at a specified time.

+ Do not switch off the main power after setting the SCHEDULE.

+ Specify the correct date and time. (See page 24.) SCHEDULE does not function unless the date and time are specified.

+ _ Check regularly that the set date and time are correct.

+ When STANDBY MODE is LOW POWER, SCHEDULE cannot be set.

+ When a temperature abnormality occurs and the backlight brightness is reduced, the brightness is not changed even ifa schedule setto BRIGHT is executed.

+ Up to 8 SCHEDULE items can be registered.

+ Setting the SCHEDULE flashes the power LED alternately in red and orange in standby mode.

+ A SCHEDULE that has a large number has precedence over that of a small number when schedules overlap.

Adjustments for PC screen display

mAutomatic adjustment

When you use the D-SUB[RGB] or DVI-1 (analog) to display a PC screen for the first time, or when you change the setting of the PC, use the automatic screen adjustment.

1. Switch the input to D-SUB[RGB] or DVI-I (analog) and display the adjustment pattern. (See the description below.)

The automatic adjustment is complete in several seconds. 5. Press [% to close the menu screen.

+_Ifthe screen cannot be adjusted properly with one automatic adjustment, repeat the automatic adjustment two or three times. Try manual adjustment if necessary.

#Screen display for adjustment

Before making adjustments in the SCREEN menu or PICTURE menu, display an image to brighten the entire screen. |f you are using a Windows PC, use the adjustment pattern on the supplied CD-ROM.

Opening the adjustment pattern The following example is performed in Windows 7. 1. Load the supplied CD-ROM into the computer’s CD- ROM drive. 2. Open [CD Drive] in [Computer]. In Windows XP, open [CD Drive] in [My Computer]. 3. Double-click [Adj_uty.exel]. The adjustment pattern will appear. Adjust the screen automatically or manually.

4. When adjustment is finished, press the [Esc] on the computer’s keyboard to quit the adjustment program. 5. Eject the CD-ROM from the CD-ROM drive.

+_Ifthe display mode on the computer you are using is 65,000 colors, the color levels in the color pattern may appear differently or grayscale may appear to be colored. (This is due to the specifications of the input signal and is not a malfunction.)

Initialization (Reset}/Functional Restriction Setting (FUNCTION)

You can return the settings to their factory-preset values and restrict operations.

1. Hold 7 down until “F” appears in the upper left corner of the screen.

2. While “F” appears, press À), , C5, Coin that order.

OK...ENTER] END...[RETURN]

3. Select and set the items.

ALL RESET Resets the settings to the factory default settings.

ENTER Press €), selectthe resetting method, and then press

ENTER After initialization, turn the main power switch off and

ALL RESET1 ….Resets all the settings to the factory default settings

ALLRESET2 Returns all settings to the factory default settings except for the following items: LAN SETUP, RS-232C/LAN SELECT, ID No. SET, BAUD RATE, NETWORK, MAIL, SERVICE & SUPPORT, and SNMP (See page 25, and pages 49 to 52.)

ADJ USTMENT LOCK You can disable operations on the monitor and the

remote control unit that use buttons

OFF .….Enables operation.

ON 1 ..Disables all operations other than turning power on/off and FUNCTION.

ON 2..Only the FUNCTION operation is enabled. Disables all operations other than FUNCTION (not even power on/off).

ADJ USTMENT LOCK TARGET Sets the target to prohibit operation of with

REMOTE CONTROL... Prohibits remote control operation

MONITOR BUTTONS … Prohibits monitor switch operation

BOTH... Prohibits remote control and

monitor switch operation

RS-232C/LAN Specifies whether to allow control via RS-232C or LAN (see pages 33 and 45).

ON Tu. Shows all menus, modes and messages.

ON 2... Hides messages automatically displayed by the display. Shows messages during operation.

OFF. Hides all menus, modes and messages.

LED Specifies whether to light the power LED.

TEMPERATURE ALERT Selects the notification method for an abnormal

OFF. Do not notify about an abnormal temperature.

OSD & LED .. When an abnormal temperature is detected, the power LED flashes in red and green alternately and the screen displays a message: TEMPÉRATURE.

LED... When an abnormal temperature is detected, the power LED flashes in red and green alternately.

STATUS ALERT Selects the notification method for a hardware error.

OFF. Do not notify about the error.

OSD & LED .. When a hardware error is detected, the power LED flashes in red and the screen displays a message: STATUS xxx].

LED... When a hardware error is detected, the power LED flashes in red.

POWER BUTTON Normally, leave this setting as MONITOR.

When using an optional part, if instruction appears, change the setting accordingly.

CONTROLLER INPUT Normally, you do not need to change this setting. When using an optional part, if instruction appears, change the setting accordingly.

4. Press en) to return to the normal screen.

+ When both abnormal temperature and hardware error are detected, the hardware error notification overrides.

+ _IfTEMPERATURE ALERT or STATUS ALERT is set to OSD&LED, alert messages will appear even if the OSD DISPLAY is set to ON 2 or OFF.

+_IfTEMPERATURE ALERT or STATUS ALERT is set to LED orOSD & LED, the LED lights even ifthe LED function is setto OFF.

Controlling the Monitor with a PC (RS-232C)

You can control this monitor from a PC via RS-232C (COM port) on the PC.

You can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 34), you can make input mode selection/adjustment or can check the status of a specific monitor.

+ To control the monitor via RS-232C, set RS-232C/LAN SELECT to RS-232C. + You cannot use RS-232C and LAN control simultaneously.

HOne-to-one connection with a PC Connect with RS-232 straight cable between the PC's COM port (RS-232C connector) and the RS-232C input terminal on the monitor.

Communication conditions

Setthe RS-232C communication settings on the PC to match the monitor's communication settings as follows:

Baud rate * Stop bit 1 bit Data length | 8 bits Flow control | None Parity bit None

*Setto the same baud rate as the BAUD RATE setting of SETUP menu. (Initial setting: 38400 bps)

* When connecting multiple monitors in a daisy chain, set all monitors to the same BAUD RATE.

Communication procedure

HCommand format When à command is sent from the PC to the monitor, the monitor operates according to the received command and sends a response message to the PC.

[ci [cz [cs Jca]p1]P2]Pp3 [Pal à]

Parameter field {4 character string comprised of: 0-9, +, -, space, ?)

Command field (4 prescribed alphanumerical characters)

RS-232 straight cable (commercially available)

Example: VOLMO030 VOLM,,,,30

#Daisy chain connection... [Advanced operation

Connect with RS-232 straight cable between the PC's COM port (RS-232C connector) and the RS-232C input terminal on the first monitor.

Next, connect RS-232 straight cable to the first monitor's RS-232C output terminal and to the second monitor's RS-232C input terminal. Connect in the same way to the third and subsequent monitors.

Up to 25 monitors can be connected. (Depending on the length of the cable used and the surrounding environment.)

RS-232C = (commercially available)

Be sure to input 4 characters for the parameter. Pad with spaces ("_”) if necessary.

Ifa command has “R”listed for “DIRECTION” in the “RS-232C command table” on page 37, the current value can be returned by using “?” as the parameter.

Example: From PC to monitor (How much 272?? VOLM? 727 is current volume setting?). 30 From monitor to PC (Current

volume setting: 30).

* [fan ID number (see page 34) has been assigned (For example, ID number = 1).

+ From PC to monitor.

+ From monitor to PC.

Controlling the Monitor with a PC (RS-232C)

BResponse code format When a command has been executed correctiy Co TK T3 4 getum code (ODH, OAH) A response is returned after a command is executed.

* fan ID number has been assigned

Space (20H) (ODH, OAH)

When a command has not been executed

CE TR TR [3 5 Retum code

* fan ID number has been assigned

Space (204) Return code (0DH, OA) CElrRIJeRJsc]o|ol1]à] — —— ID number

+_“ERR'is returned when there is no relevant command or when the command cannot be used in the current state of the monitor.

If communication has not been established for reasons such as a bad connection between the PC and monitor, nothing is returned (not even ERR).

“ERR" may be returned when a command cannot be received correctly due to interference from the surrounding environment.

Please ensure that the system or software retries the command if this occurs.

If no monitor has been assigned the designated ID number (e.g. if the command IDSLO002 [1 is used, but no monitor With ID number: 2 is found), no response is returned.

If execution of the command is taking some time

Return code (ODH, AH)

When the following commands are used, “WAIT” is returned. In this case, a value will be returned if you wait a while. Do not send any command during this period. No ID number is attached to WAIT response. + Commands which return WAIT: 1... When repeater control is used 2. When an IDSL or IDLK command is used 3. When one of the following commandés is used: RSET, INPS,ASNC, WIDE, EMAG, EPOS, PXSL,POWR, AGIN, MWIN, MWIP, MWPP, ESTG, EMHV, EPHV,

ESHV, ENLG When control via RS-232C is locked (to prevent use) using the operation lock function (see page 33)

Retum code (ODH, OAH)

mCommunication interval + After OK or ERRis returned, you must send the following commands To set a timeout for the command response, specify 10 seconds or longer. When connecting multiple monitors in a daisy chain, set the timeout to at least the product of the monitor's position from the computer multiplied by 10 seconds. Example) 3rd monitor from computer: 30 seconds or longer. *_Provide an interval of 100 ms or more between the command response and the transmission of the next command. VOLM0020 Ok

| Interval of 100 ms or more

+ _ When executing ALL RESET, set the timeout period to 30 seconds or longer.

+ When turning the power on while the POWER ON DELAY function is in use, set the timeout period to the POWER ON DELAY period + 10 seconds or longer.

This section explains commandés for daisy chain connection. The basic communication procedure is the same as in the “One-to-one connection with a PC” section.

You can assign a unique ID number to each monitor (see page 25). This allows you to control a particular monitor in a daisy chain of monitors. You can assign ID numbers either from the menu screen or from the PC using RS-232 cable. lExample] ID number. 1 ID number: 4

ID number: 2 ID number: 3

If monitors are connected as shown above, you can execute commands like “Set the volume of the monitor with ID 4 to 20”.

When designating ID numbers for a set of monitors linked in a daisy chain, you should basically avoid any duplication of ID numbers. ID numbers do not have to be assigned in ascending order starting from the PC. They can also be connected as shown below.

ID number: 3 ID number. 2 ID number: 4 ID number 1

HCommands for ID control The command examples shown on this page assume the following connection and ID number set up.

ID number. 2 ID number: 3

ID number. 1 ID number: 4

….A monitor receiving this command sets its own ID number in the parameter field.

OK,,001 + The ID number of this monitor is set to 1.

You can automatically assign ID numbers by using the IDST command with the Repeater control (see “Repeater control” on page 36). For example, using the command “IDST001+” automatically sets the ID numbers, as shown below. lExample] ID number. 1 ID number. 4

ID number 2 ID number: 3

IDSTO01 + <— ID setting command with repeater control WAIT Ok, ,001 <— “OK” response from ID number: 1 OK, ,002 <— _“OK"response from ID number: 2 OK, , 003 <— _ “OK"response from ID number: 3 OK, ,004 < _“OK"response from ID number: 4 (End) IDSL The parameter of this command sets the ID number of the monitor. The monitor is subject to the next command. Example: The next command is for the monitor IDSLO002 in ID number 2. WAIT … Seercrng for monitor with ID number: OK, , 002 <— Found monitor with ID number: 2 Sets volume of monitor with ID VOLMO00 +" Humber: 2 to 30. WAIT + Processing OK response from monitor with ID oK_ 00 + number: 2 VOLMO020 + Sets volume to 20. The volume of the monitor with ID OK.,001 + number: 1 (the one directly connected to the PC) is set to 20.* * The IDSL command is effective only once, for the immediately succeeding command.

Controlling the Monitor with a PC (RS-232C)

IDLK The parameter of this command sets the ID number of the monitor. The monitor is subject to all subsequent commands.

Example: Following commands are for the monitor IDLKO002 +" Win ID number 2. WAIT . Seerching for monitor with ID number: OK, ,002 + Found monitor with ID number: 2 Sets volume of monitor with ID VOLMO080 <—" hümber: 2 to 30. WAIT <— Processing OK, ,002 Sets volume of monitor with ID VOLMO020 <—" hümber: 2 to 20. WAIT OK, ,002 IDLKO000 + Canceling fixed ID number setting WAIT <— Canceling IDLK OK,,002 + Cancelation complete VOLMO0010 The volume of the monitor with ID number: OK,,001 + 1 (the one directly connected to the PC) is set to 10. (IDLK is canceled.) * The IDLK command remains effective until it is canceled, or power is shut off.

IDCK Provides screen display of the ID number currently assigned to a monitor, and the ID number currently set for IDLK (if any).

Example: (After executing IDLKOO02) IDCKO000 <_ (Parameter has no meaning.) Retumed response. The ID ID:001 IDLK:002 +« numberis also displayed on the monitor screen. IDCKO00 + < _ Repeater control. (Ifa command is used with repeater control, ID WAIT designation using IDSL or IDLK ID:001 IDLK : 000 Is canceled.} ID :002 IDLK : 000 ID :003 IDLK : 000 ID :004 IDLK : 000

Controlling the Monitor with a PC (RS-232C)

This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater control function without assigning ID numbers.

Setting of the GAMMA user data

#To transfer the GAMMA user data

Use the user data transfer commands (UGRW, UGGW and UGBW). For each ofthe R, G and B colors, divide the total

lExample] 512 pieces of user data into 16 blocks, and transfer 32 pieces Set1 Set2 Set3 Set4 of data with each command. me 1 T1 F1 [c1]c2]c3[ca]P1lPp2[Pp3[Pp4] [s1]52]

*_ If monitors are connected as shown above, you can execute a command like “Set all monitors’ input settings to D-SUB[RGB/".

æRepeater control command

Repeater control is achieved by setting the FOURTH CHARACTER of the parameter to “+”.

VOLMO30 + «Sets volume of all monitors to 30.

In repeater control, responses are returned by all the connected monitors

If you want to determine that a value has been returned by a specific set, assign ID numbers to each monitor in advance. When some monitors do not return their responses, the probable cause is thatthe monitors could not receive the command or command processing is not complete. Do not send a new command.

Example: (When 4 monitors are connected, and assigned ID numbers: 1 through 4)

WAIT OK, , 001 OK,, 002 OK, 003

OK, 004 < _If4 monitors are connected in

a chain, reliable operation can be ensured by sending a new command only after a reply has been returned by 4th (last) monitor.

Repeater control can also be used for reading settings.

Example: VOLM??7?+ WAIT 10,, 001

20,,002 Volume settings for all 30, , 003 monitors are returned.

+_Ifrepeater control is used during ID designation (IDSL, IDLK), the ID designation is canceled.

Command field Block number (01to 16) Data field Checksum field

Example: To transfer the data of block 1 (0 to 31 levels) ofred (R) data

Command Block number

If data is less than 4 digits, add a “0” (zero) to make it 4 digits

The checksum field is the character string (ASCII) data of lower-order one byte which indicates the sum of the block number and 32 pieces of data in hexadecimal (0 to F).

#Saving the GAMMA user data

Use the user data save command (UGSV) to save the

transferred user data in the monitor.

Ifthe data is not saved, it will be cleared when:

+ The main power switch is off

+ STANDBY MODE is LOW POWER and the monitor enters standby mode

mActivating the GAMMA user data To activate the transferred user data, select USER for GAMMA

ofthe PICTURE menu, or send the corresponding RS-232C command

ÆChecking the GAMMA user data

Use the user data read commands (UGRR, UGGR and UGBR) to return 512 pieces of user data for each oftheR, G and B colors. Divide the data into 16 blocks and return 32 pieces of data with each command. The value to be returned is not the value stored in the monitor, but the value in the temporary memory for display. (These values are the same when the user data save command (UGSV) above has been sent.)

+ The user data is not initialized by RESET of the PICTURE menu. To initialize the user data, use ALL RESET of the FUNCTION menu. The GAMMA user data initialize command (UGRS) allows the initialization of the user data only.

Controlling the Monitor with a PC (RS-232C)

RS-232C command table

How to read the command table

R The returned value indicated under “Reply” can be obtained by setting “????", “_,.,

W When the “Parameter” is set in the parameter field (see page 33), the command functions as described

Command: Command field (See page 33.) Direction: under “Control/Response Contents”. (repeater control) in the parameter field (see page 33). Parameter: Parameter field (See page 33.) Reply: Response (Returned value)

e” indicates a command which can be used in power standby mode regardless of the STANDBY MODE setting. indicates a command which cannot be used in power standby mode when STANDBY MODE is set to LOW POWER.

“—" indicates a command which cannot be used in power standby mode regardless of the STANDBY MODE setting.

Power control/Input mode selection

Function Command | Direction | Parameter

Relums from standby mode.

Input signal waiting mode

INPUT MODE SELECTION IPS |[w

Toggie change for input mode. Terminals not selected in INPUT SELECT cannot be selected

DVET D-SUBIRGE] “ERR" when other than RGB is selected for D-SUB of INPUT SELECT.

D-SUBICOMPONENT] “ERR" when other than COMPONENT is selected for D-SUB of INPUT SELECT.

D-SUB[VIDEO] “ERR" when other than VIDEO is selected for D-SUB of INPUT SELECT.

HDMITAVI “ERR" when PC is selected for HDMI of INPUT SELECT.

HDM(PC] “ERR" when AV is selected for HDMI of INPUT SELECT.

HDMI2[AV] “ERR" when PC is selected for HDMI2 of INPUT SELECT.

HDMI2IPC] “ERR" when AV is selected for HDMI2 of INPUT SELECT.

Controlling the Monitor with a PC (RS-232C)

Controlling the Monitor with a PC (RS-232C)

Function Command | Direction | Parameter Reply Control/Response contents + ADVANCED AUTO AGIN w 1 When the input mode is D-SUB[RGB], DVI-I (analog). = ANALOG GAIN ANGA |[WR 0-127 0-127 | When the input mode is D-SUBIRGB], DVH (analog). ANALOG OFFSET ANOF |[WR 0-127 0-127 | When the input mode is D-SUBIRGB], DVH (analog). 3D-NR (AV input} TDNR WR 0-2 0-2 | 0: OFF, 1: LOW, 2: HIGH MPEG-NR (AV inpuÿ mPNR [ur 01 01 [o:orr 1:.0N ET vesr [ur 01 0: [0: OFF, 1: ON (Wen ie input mode is D-SUBIVIDEO)) RGB INPUT RANGE FHDR [Ur 07 02 AUTO, f: FULL, 2: LINITED CHOMATAVD RGB INPUT RANGE FHDR [un 57 DT OAUTO, F FULL, 2 LINTED CHDMHIPCD RGB INPUT RANGE FAR [Ur 07 DZ AUTO, H FULL, 2 LINITED (HDMI2[AV]} RGB INPUT RANGE FR [un 07 DZ AUTO, H FULL, 2 LINITED (HDMI2[PC]) RGB INPUT RANGE FOR [un 7 F2 [TFULL 2 LME tv) RGB INPUT RANGE PDSR MR 12 1-2 | 1: FULL, 2: LIMITED 9 (D-SUB) RGB INPUT RANGE FOPR [un 57 DT OAUTO, F FULL, 2 LINTED (DisplayPor) ACTIVE CONTRAST (AV inpug [CNT [WA Gi DH f0 OF ON DISPLAY COLOR PATTERN [PIDF | UR 5 D [No patte display ï T | Wie single color patte dpi. z Z Red single coior palier display 3 | Green sngie cor pate display 3 | Biue single color paltem display w 35 | Redigreenbiue mixed color palier dispiay. Set each colors level with RED, GREEN, BLUE DISPLAY COLOR PATTERN (R) | PTDR WR 0-15 0-15 | “ERR” when PTDF is not set to 99. DISPLAY COLOR PATTERN (G) | PTDG WR 0-15 0-15 DISPLAY COLOR PATTERN (B) | PTDB WR 0-15 0-15 RESET FAST |w z = AUDIO menu Function Command | Direction | Parameter Reply Control/Response contents * TREBLE AUR [ur 55 35 BASS RUES [ur 35 35 o BALANCE FUEL [ur ETAT] ETAT] RESET FAST [w 3

Controlling the Monitor with a PC (RS-232C)

Controlling the Monitor with a PC (RS-232C)

Controlling the Monitor with a PC (RS-232C)

In landscape orientation

In portrait orientation

Controlling the Monitor with a PC (RS-232C)

Function Command | Direction Parameter Reply Control/Response contents + PIF MODES DUDBMU 03 D ]0: OFF 1: PIE 2: PDyP 2: PhyP2 PIPSZE MPSZ [ a a FIFPOS THELONGEST [MHPs [ur D-100 DIRECTION R T0 THESHORTEST [Nwrs [W DH00 DIRECTION R vo PIPFOS LD+SD BATCH WPOS [ir D1000-100 Speciÿ ie posifon in NPOS0yy om a {tx Longer side, yy: Shorter side position) R 0-100,0-100 | Returns à response in (oct yyy) format, {tx Longer side, yy: Shorer side position) PP ELEND DLL CE CE FIF SOURCE FAP ir ï jour 2 2 [D-SusRGE] ° 3 3 [D-SUBICOMPONENT] 4 4]D-SUBIVIDEO] D [RONA To F0 [HOMTPCT 12 12 | HDMI2[AV] 13 13 [HDMI2[PC] a 4 [Dispiayron SOUND CHANGE TU F2 F2 [E MAIN 2: SUE MAIN POS (ain screen FAP ÎUR vi DT |0: POST. 1: POSZ PbyP2 POS (Sub screen) MW2P [WR 02 0-2 [0: POST, 1: POS2, 2: POS3 AUTO OFF. MOFF— [u o1 G:1 [0 MANUAL, FAUTO OTHERS menu Function Command | Direction Parameter Reply ControlResponse contents F SCREEN MOTION | PATTERN scsv [ur 04 02 [0: OFF. 14: PATTERNIA MONON TMER [MT [UR D20 52 MOTIONTIMEZ [MINT | UR 10-290 10-990 | Per 10 seconds (PATTERN 1) MOTIONTIMEZ [MINT [UR 520 5:20 [Persecond (PATTERN2-4) © POWER MANAGEMENT (PC) FRNS [ur vi DT ]O OF ON POWER MANAGEMENT (AV) PMAv [ur oi 01 [0:-0FF 1 ON AUTO INPUT CHANGE AIN [ur 01 0-1 [0-OFF 1. ON LOGO SCREEN BTSC [ur oi GT [0 OFF TON INPUT RESOLUTION CHECK |PXCK R - [Returns current resolution in the form of hhh, vuv. fESoLUTION PHELSETNG |PISL [WA ï T [768) 160 x 768 peurs z 7 [760 60x76 3 5 [res 1024 x 768 5 5 [480) 848 x 480 6 F [460 GO x 480 7 7 [ 1050) 1680 x 1050 O 5 | 1050) 1400 x 1050 D D [768 AUTO 50 10 [asorauro MPUTRESOLUNON AN [RESOLUTION CHECK [RESO |A — [4801 480p, 10801. 720p. 1080p. VOA. ete ZOONZ SPECIAL SETTINS ZSP [ur Gi GT |0-OFF TON {D-SUB(RGB], DVI-(analog)) SCAN MODE SCAN [WR 02 0-2 [0: MODEN, 1: MODEZ, 2: MODES (When the input mode is AV) ° COLOR SYSTEM csvs [ur vs 0:5 [0: AUTO, 1: PAL, 2: PAL:60, 3: SECAM, 4: NTSC3.58, 5: NTSC4.48

Controlling the Monitor with a PC (RS-232C)

Initialization/Functional Restriction Setting (FUNCTION) menu

Function Command | Direction Parameter Reply Control/Response contents + RLLRESE. RSET_[w G1 DALLRESET 1, LALLRESET 2 ADJUSTMENT LOCK AR [ur 02 DZ ]0-0FF ON ZON2 ADJUSTMENT LOCK TARGEL AG [ur 02 07 | 0: REMOTE CONTROL, MONITOR EUTTONS, 2 BOTH DSD DISPLAY COUR 02 02 ]0:-ONT. 1: OFF. 2: ONZ LED CUS oi 6-1 ]0 ON. E OFF TEMPÉRATURE ALERT TA fur 02 02 ]0:-OFF 1: CSD ALED. 2 LED o POWER BUTTON PETN [ur oi 0-1 |0:- MONITOR, 1: CONTROLLER CONTROLLER INPUT POP [UR 04 04 |0:D-SUE, F: DisplayPon, 2 HDMI, HDMI, 4 DVI (ERR" when MONITOR is selected for POWER BUTTON.) STATUS ALERT SAT [Ur vz DZ ]0-OFF 1: 08D A LED. 2 LED Others Function Command | Direction | Parameter Reply Control/Response contents + SOREEN S1E (PC) WDE [ur F5 5 [WIDE Z: NORMAL, 3: Dotby Dot, 4: ZOOMI, 5: ZOOMZ SCREEN SIZE (AV) WIDE WR 15 15 | f: WIDE, 2: ZOOM', 3: ZOOM2, 4: NORMAL, 5: Dot by Dot o VOLUME VOLM _[WR Dai vai MUTE MUTE [ur 01 0-1 [0-OFF TON INFORMATION — [MODEL INF JR Value SERIAL NO SRNO R Value ° TENPERATURE SENSOR DSTA [R 0 [iremaltempenure romal T iniemaltemperaiure abnommai has occurred and the monior sin sandy mode 2 |Intemal temperature abnormal occurred (To delete the information of temperature abnormal, turn off the main power.) ° 3 [intemal temperaiure abnommai has occurred and ackight brighiness is dimmed 2 [remperure sensor abnommal TEMPERATURE ACQUISITION ERRT [AR Value | Temperature at temperature sensors 1 through 6 are returned in {he following forms: {Sensor 1], [Sensor 2], [Sensor 3], [Sensor 4], [Sensor 5], [Sensor 6] ° indicates a temperature sensor abnormalty when "126" is returned. CAUSE OFLAST STANDEY MODE |STCA | 5 Iialzaion R 0 | No detectable error has occurred T | Stancby mode by POWER buton Z | Main power by he main pouer sue 3 [Standby mode by RS-232C or LAN . 4 [input signal waling mode By No Signai 5 [Standby mode by abnormal temperalure [Standby mode by SCHEDULE setting 20 |Siandby mode by OFF IF NO OPERATION setting

Controlling the Monitor with a PC (LAN)

Your monitor can be connected to a LAN allowing you to

control it from a PC on the LAN You can also configure the monitor to send e-mail notification when it has a problem.

The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through).

LAN cable (commercially available, straight)

+ You must assign an IP address to the monitor by following the procedures in “Settings to connect to a LAN”. (See the description on the right.)

+ Your PC must be installed with Internet Explorer (version 7.0

To control the monitor via LAN, set RS-232C/LAN SELECT

to LAN. (See page 25.)

+ You cannot use RS-232C and LAN control simultaneously.

Initializing personal information

+_ Personal information such as e-mail addresses can be registered in the monitor. Before transferring or disposing of the monitor, initialize all settings by selecting ALL RESET 1. (See page 32.) Note that ALL RESET 2 will not initialize e-mail addresses and other settings

Settings to connect to a LAN Set the monitor’s IP address and subnet mask to match the settings of your LAN.

These settings can be made on either the monitor or a PC connected to the monitor.

The settings depend on the configuration of your LAN. Ask your LAN administrator for details.

= To set on the monitor

Set RS-232C/LAN SELECT of COMMUNICATION SETTING on the SETUP menu to LAN, and then setthe LAN SETUP options. (See page 25.)

After setting each item, select SET and press 2.

DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON. To set the address manually, set this to OFF.

IP ADDRESS Ifthe DHCP CLIENT is set to OFF, specify an IP address.

Por : A + Press © jorç to selectitems, and press Core jto change the values.

SUBNET MASK Ifthe DHCP CLIENT is set to OFF, specify the subnet mask.

DEFAULT GATEWAY Ifthe DHCP CLIENT is set to OFF, specify the default gateway.

If you are not using a gateway, specify “0.0.0.0”.

ER : = + Press © jorc to selectitems, and press Core jto change the values.

Select ON and then press es.

+ When the IP address is set manually, the IP addresses of the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 25.)

Controlling the Monitor with a PC (LAN)

= To set from a PC When the monitor is connected to a PC, LAN settings can be configured via PC.

(1) Connect your monitor to a PC

(2) Specify the PC's IP address

(3) Configure the monitor's LAN settings

(1) Connecting your monitor to a PC Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the PC and this monitor.

To LAN terminal [_] TE D = LAN cable

(commercially available, crossover)

(2) Specifying the PC's IP address

To configure the monitor's LAN settings, you must temporarily

change the settings on the PC.

This explanation is based on Windows 7.

1. Log on to the PC with an administrator account.

2. Click [Start], and then click “Control Panel”.

3. Click “View network status and tasks” in “Network and Internet”. In “Classic View”, click “Network and Sharing Center”.

4. Click “Local Area Connection” and then “Properties”.

5. Click “Internet Protocol Version 4 (TCP/IPv4)" and then “Properties”.

6. Make a note of the current IP address, subnet mask, and default gateway settings. Make sure you write this information now as you will be changing the IP address, subnet mask, and default gateway settings back to these settings afterwards.

7. Temporarily change the IP address and subnet mask. To access the monitor as it is shipped from the factory, set as follows. +_IP Address: 192.168.150.1 + Subnet Mask: 255.255.255.0 + Default Gateway: (leave blank)

LES Internet Protocol Version 4 (TCP/Pv4) Properties

Lit at he SG ei are bear Ferre Pre |

Obtain an IP address automatically

IP address: 192.168 150, 1

8. Click [OK] and then reboot the PC.

+ This monitor is factory preset as shown below. (When DHCP CLIENT is setto OFF) IP Address : 192.168.150.2 Subnet Mask : 255.255.255.0 Default Gateway: 0.0.0.0

(3) Configuring the monitor’s LAN settings Access the monitor using Internet Explorer.

Controlling the monitor

1. Turn the power ON to the monitor.

2. Set RS-232C/LAN SELECT of COMMUNICATION SETTING on the SETUP menu to LAN

. Set DHCP CLIENT of LAN SETUP of COMMUNICATION SETTING on the SETUP menu to OFF PC operation

4. Launch Internet Explorer, in the “Address” box type “http://192.168.150.2/" and press the Enter key.

5. Click on “LAN SETUP” under NETWORK.

6. Specify the “DHCP CLIENT”, “IP ADDRESS",etc.

Remo -Ua sen. 5 Eouro. _—

DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to “ON”. To set the address manually, set this to “OFF”.

IP ADDRESS Ifthe DHCP CLIENT is set to “OFF”, specify an IP address.

SUBNET MASK If the DHCP CLIENT is set to “OFF”, specify the subnet mask.

9. Exit Internet Explorer.

10. Restore the PC's IP address jotted in Step 6, “(2) Specifying the PC's IP address”.

11. Connect the monitor and the PC to the LAN.

+ Wait 10 seconds after clicking [OK] before proceeding. + When operating using the remote control unit or similar, click [Refresh].

+ When the IP address is set manually, the IP addresses of the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 25.)

Controlling the Monitor with a PC (LAN)

Controlling with a PC

= Basic operation You use Internet Explorer on a PC onthe LAN to controlthe monitor. 1. Launch Internet Explorer on the PC. 2. Inthe “Address” box, type “http://" followed by your monitor's IP address followed by “/”, then press the Enter key. You can confirm the IP address with the DISPLAY function.

When prompted to enter a user name and password, type the user name and password that you specified in the security settings (see page 49), and click [OK].

3. You can check, control, and change the monitor's status and settings by clicking the menu items on the left side of the screen

+ _lf you see an [Apply] button next to a setting, click it after you change that setting.

+ See pages 48 to 52 for details on each setting.

+_lf you click [Refresh] before the screen finishes updating the current display, the “Server Busy Error” will appear. Wait for a moment before operating your monitor again.

+ You cannot operate the monitor while it is warming up.

+_If“DHCP CLIENT" is set to “ON’, press + on the remote control unit two times and then check the monitor's IP address.

Controlling the Monitor with a PC (LAN)

# INFORMATION Information about this monitor appears.

= CONTROL You can control the operations corresponding to the buttons POWER INPUT SIZE : { €) €) on the remote control unit. (See page 18.)

Ures +_In standby mode, Power ON is the operation available.

= ADJUSTMENT You can adjust these settings which are also available on the monitor's menu.

+ After changing DISPLAY COLOR PATTERN to OFF, click [Refresh] to correctly retrieve the status of the monitor.

= NETWORK (LAN SETUP)

This screen allows you to set the settings necessary when the monitor is connected to a LAN.

DHCP CLIENT If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON.

To set the address manually, set this to OFF.

IP ADDRESS Ifthe DHCP CLIENT is set to OFF, specify an IP address.

SUBNET MASK Ifthe DHCP CLIENT is set to OFF, specify the subnet mask.

DEFAULT GATEWAY Ifthe DHCP CLIENT is set to OFF, specify the default gateway.

DNS SERVER ADDRESS AUTO ACQUISITION Ifthe DHCP CLIENT is set to ON, specify whether or not to automatically obtain the DNS server address.

is SET to OFF orthe DNS SERVER ADDRESS AUTO ACQUISITION is setto OFF.

RESET Clicking [Execute] returns all of the LAN SETUP settings to the factory-preset values except for the DNS SERVER ADDRESS AUTO ACQUISITION and DNS SERVER settings

+ When the IP address is set manually, the IP addresses of the monitor connected to the RS-232C output terminal and the daisy chain of connected monitors that follows can be assigned automatically. (See page 25.)

Controlling the Monitor with a PC (LAN)

= NETWORK (SECURITY)

This screen allows you to specify the security-related settings.

conrroL ADJUSTMENT SERVICE & SUPPORT USER NAME / PASSWORD Sets up a user name and password to restrict access to this monitor. After entering a user name and password, click [Apply].

ACCEPT IP ADDRESS You can limit access to this monitor by registering IP addresses of PCs that should have access

To limit access, specify the option “From only specific IP addresses”. Otherwise, to allow access from any PC, specify "AIT IP Addresses”.

If“ACCEPT IP ADDRESS" is set to “From only specific IP addresses”, enter the IP addresses that you want to allow.

+ The USER NAME and PASSWORD can be up to 8 alphanumeric characters (hyphens and underscores allowed).

+ _ To cancel the user name and/or password after it has been set, make the box empty and click [Apply].

Controlling the Monitor with a PC (LAN)

MONITOR NAME Specify a name for this monitor as it should appear on the Internet Explorer screen.

AUTO LOGOUT TIME Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network.

Specify in minutes from 1 to 65535. A value of ‘0’ will disable this function.

DATA PORT Specify the TCP port number to use for exchanging data with the monitor.

Specify a value from 1025 to 65535.

LINK MODE Selects the link speed and duplex. Use AUTO normally.

+ The MONITOR NAME can be up to 16 alphanumeric characters or symbols.

+ _ Enter up to 50 characters in the NAME field in the INSTALLATION INFORMATION.

+ _ Enter up to 100 characters in the LOCATION field in the INSTALLATION INFORMATION.

This screen allows you to configure the e-mail sent periodically or when the monitor has an error.

The settings depend on the configuration of your LAN. Ask your LAN administrator for details.

This address becomes the e-mail address of the originator.

ORIGINATOR NAME Specify the name for the originator.

This name appears in the “Originator Name” field of the

POP SERVER If the “AUTHENTICATION" is “POP before SMTP”, specify

the POP server address.

ACCOUNT NAME / PASSWORD Ifthe "AUTHENTICATION"is ‘POP before SMTP"or

“SMTP-AUTH", specify the account name and password to connect to the SMTP server.

+ You can enter up to 64 alphanumeric characters or symbols for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR NAME, ACCOUNT NAME, and PASSWORD.

+ The SMTP SERVER and POP SERVER can be up to 64 characters.

The following characters can be used: a-z, A-Z, 0-9, -,.

= MAIL (RECIPIENT) This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error.

Controlling the Monitor with a PC (LAN)

When PERIODICAL for CONDITION of MAIL (RECIPIENT) is checked, set the date and time to send the mail.

RECIPIENT E-MAIL ADDRESSES Specify the e-mail addresses to send error notification e-mail to

CONDITION Specify the conditions to send mails. When you check PERIODICAL, specify the date and time to send the mails in the PERIODICAL setting

CONFIRMATION Sends test e-mail.

This allows you to confirm that the e-mail settings are configured properly.

Attach the log file to a TEMPERATURE/HARDWARE error e-mail.

When this option is checked, a log is added to the mail which notifies a temperature or status error.

+ The RECIPIENT E-MAIL ADDRESSES can be up to 64 alphanumeric characters or symbols.

DAY OF THE WEEK Specify the day of the week to send the periodical mails.

TIME Specify the time of the day to send the periodical mails.

+_ Do not turn off the main power when you set to send the periodical mails.

+ Specify the correct date and time. (See page 24.) Ifthe date and time settings are incorrect, the periodical mail is not sent properly.

+ _Regularly confirm that the specified date and time is correct.

+ When LOW POWER is selected for STANDBY MODE, periodical mails will not be sent in standby mode.

Controlling the Monitor with a PC (LAN)

= SNMP You can configure settings related to SNMP.

SNMP SETTING Set whether to enable or disable SNMP.

VERSION Setthe version of the SNMP to be supported.

COMMUNITY NAME 1 to 3 Set the name of the community required for the access.

Set the user name, password, authentication method and other options required for access.

TRAP SETTING Set whether to enable or disable the trap function. When this function is enabled, a trap will be sent when the monitor is turned on.

TRAP SETTING OF AUTHENTICATION ERROR Set whether the trap function sends a notification when authentication fails.

TRAP ADDRESS & PORT Setthe destination address and port number of the notification sent by the trap function.

+ After you set SNMP, click [Switch the main power of monitor off and on now.] or turn off the monitor and then turn it on again with the main power switch. When the monitor restarts, wait about 30 seconds and then start the next operation.

+ _lfthe IP address is changed while the SNMP function is operational, turn off the monitor and then turn iton again With the main power switch.

+ Depending on the SNMP settings, a short delay may occur before the SNMP is usable. (About 5 minutes)

+ Up to 16 alphanumeric letters and symbols can be used for the community name, user name and password.

Up to 64 alphanumeric characters or symbols can be used.

CONDITION Specify the condition to display the URL.

CONFIRMATION The home page of the specified URL is displayed. You can check whether the URL you entered is correct.

+ _Itis also possible to specify the message text, such as the name of a contact or a telephone number, to be displayed instead of the linked URL.

[Advanced operation] Command-based control

You can control the monitor using RS-232C commands (see page 36) via terminal software and other appropriate applications.

In order to use this function, enable a connection to the monitor through Internet Explorer.

Read the manual for the terminal software for detailed instructions.

(1) Connect the PC to the monitor. 1. Specify the IP address and data port number and connect the PC to the monitor. When connection has been established successfully, [ELogin:]is returned as response. 2. Send the user name set in the SECURITY settings (see page 49). + Send [User name] + [1]. +_Ifthe user name is not set, send [CI] + When the transmission is successful, is returned as response. 3. Send the password set in the SECURITY settings (see page 49). + Send [Password] + [[1]. +_Ifthe password is not set, send [C1]. + _ When the transmission is successful, [OK [I] is returned as response. (2) Send commands to control the monitor. +_ The commands used are the same as those for RS- 232C. Refer to the communication procedure (see page 33) for operation. + Usable commands are provided in the RS-232C command table (see page 37). (3) Disconnect the connection with the monitor and quit the function. 1. Send [BYE C1]. When the transmission is successful, [goodbye] is returned and the connection is disconnected.

+ _ Connection is automatically disconnected when the time specified in AUTO LOGOUT TIME elapses over a no-communication period.

Controlling the Monitor with a PC (LAN)

If you are experiencing any problem with your display, before calling for service, please review the following troubleshooting tips.

There is no picture or sound.

+_Is the power cord disconnected? (See page 13.)

+ _Is the main power switch off? (See page 16.)

+_Is the monitor in standby mode (the power LED illuminating in orange)? (See page 16.)

+ Make sure correct input mode is selected. (See page 18.)

+_ If any external equipment is connected, make sure the equipment is operating (playing back).

Remote control does not work.

+ Are the batteries inserted with polarity (+.-) aligned? (See page 15.)

+ Are the batteries exhausted?

+_ Point the remote control unit toward the monitor's remote control sensor. (See page 15.)

+_Is the menu display hidden or is operation disabled? (See page 32.)

Sound from left and right speakers is reversed.

Sound is heard from only one side.

+ Are audio cables connected properly?

+ Check the setting of BALANCE for AUDIO menu. (See page 24.)

There is a picture but no sound.

+ _Is the sound muted?

+ Make sure the volume is not set to minimum.

+ Are audio cables connected properly?

+_Is the setting of AUDIO SELECT on the SETUP menu correct? (See page 24.)

+ _ The signal may be incompatible.

+ _ Try the automatic screen adjustment when the D-SUB[RGB] or DVI-I (analog) are used.

The video from the PC/AV HDMI input terminal does not

+_Is the setting for HDMI1 or HDMI2 of INPUT SELECT on the SETUP menu correct? (See page 24.)

+ _Is the HDMI cable HDMI standard compliant? The monitor will not work with cables that are not standard compliant. +_Is the input signal compatible with this monitor? (See page

The video from the DVI-I input terminal does not appear

+_Is the setting for EDID SELECT (DVI-I) of INPUT SELECT on the SETUP menu correct? (See page 24.)

+_Is the input signal compatible with this monitor? (See page 59.)

+_ Turn off the power to the connected equipment and then turn the power on again.

+_Ifthe monitors are connected in a daisy chain, turn off the power to all the monitors connected in a daisy chain and then turn the power on again.

The video from PC/AV D-Sub input terminal does not

+_Is the setting for D-SUB of INPUT SELECT on the SETUP menu correct? (See page 24.)

+_Is the input signal compatible with this monitor? (See page 59.)

The video from the DisplayPort does not appear properly. +_Is the input signal compatible with this monitor? (See page 59.)

Control buttons do not work.

+ Load noises from outside may be interfering with normal operation. Turn off the power and turn it on after waiting at least 5 seconds, and then check the operation.

The input mode changes automatically.

+ _ When the AUTO INPUT CHANGE is ON and no signal is present in a selected input mode, the AUTO INPUT CHANGE automatically changes the selected mode to a mode where a video signal is present.

The input mode may change in the following cases: - When a computer is in standby mode. - When video play is stopped with a playback device.

Power LED flashes red.

“STATUS [xxxx]” appears in the corner of the screen.

+ Hardware has a problem. Turn off the monitor and request repair from your SHARP dealer. (When STATUS ALERT is set to OSD & LED. This varies depending on the setting.)

When “AUTO DIMMING” is displayed.

+ _ When the internal temperature of the monitor rises excessively, the brightness of the backlight automatically decreases in order to prevent a further temperature rise. If you attempt to use % > to adjust the brightness while the monitor is in this state, “AUTO DIMMING” is displayed and you cannot change the brightness.

+ Remove the cause of the excessive temperature rise.

The monitor makes a cracking sound.

+ You may occasionally hear a cracking sound from the monitor. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the monitor's performance.

The Power LED is flashing in red and green alternately. When “TEMPERATURE” is displayed in the corner of the screen.

+ _ When the internal temperature of the monitor rises excessively, the brightness of the backlight decreases automatically in order to prevent high-temperature- related problems. When this occurs, TEMPERATURE"is displayed on the screen and the Power LED flashes red and green alternately. (When TEMPERATURE ALERT is set to OSD & LED. This varies depending on the setting.)

+_Ifthe internal temperature rises further, the monitor automatically enters standby mode. (The Power LED continues flashing red and green alternately.)

+ Remove the cause of the excessive temperature rise.

- Ifthe monitor enters standby mode due to a rise in temperature, to return to normal display, turn the power switch off and then back on again. The monitor, however, will enter standby mode again if the cause of the temperature rise is not eliminated. (See page 7.)

- Check whether the monitor is placed at a location where a quick rise in temperature is likely. Internal temperature rises quickly if the vents on the monitor are blocked.

- Internal temperature rises quickly if dust accumulates inside the monitor or around the vents. Remove dust if

possible. Ask SHARP dealer about removing internal dust.

*1 D-Sub input terminal only.

*2 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such cases, please check the temperature condition specified by the optional equipments.

*3 When AUTO INPUT CHANGE is set to OFF.

*4 When STANDBY MODE is setto STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

[PN-R703] VESA hoies * T8 718 200] (200 er, RO Unit inch [mm] aan 62218 1578) Ga - Opening width(60-11/16 [1541]) & TT É ns =

When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.

SHARP recommends using M6 screws and tighten the screws.

Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in

serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch (8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times

or more the weight of the monitor.

[PN-R603] == =] VESA holes * 118 118 ii PO Do] Unit inch [mm] y 41-916 54-1/4 [1378] ñ gsngfr15n6, | fai | frooronr Opening vit (52:24 140) | u ï ë î | ... Ë Ë = IC ] ]= ET nn :

When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.

SHARP recommends using M6 screws and tighten the screws.

Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in

serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch (8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times

or more the weight of the monitor.

This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in order for the monitor's power management function to work.

DMPM: Digital Monitor Power Management Power Power DPMS | Screen | onsumptiont | HSYn€ | Vsync DMPM Screen | consumption 270W . 270W ONSTATE | Display Yes Yes Monitor ON | Display 200 W 200 W STANDBY No Yes 14WF À Active OFF | No displa suspend | N° 14W Yes No pey 14W* display 14 W*# OFF STATE No No

#DDC (plug and play)

The monitor supports the VESA DDC (Display Data Channel) standard

DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect plug-and-play monitors.

There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.

HCompatible signal timing (PC)

. Digital Analog Screen resolution Hsync Vsync Dot frequency| Di HD DisplayPort| (D-SUB/DVH) VESA 640 x480 31.5kHz 60Hz 25.175MHz Yes Yes Yes Yes 37.9kHz 72Hz 31.5MHz Yes Yes Yes Yes 37.5kHz 75Hz 31.5MHz Yes Yes Yes Yes 800 x 600 35.1kHz 56Hz 36.0MHz L = - Yes 37.9kHz 60Hz 40.0MHz Yes Yes Yes Yes 48.1kHz 72Hz 50.0MHz Yes Yes Yes Yes 46.9kHz 75Hz 49.5MHz Yes Yes Yes Yes 848 x480 31.0kHz 60Hz 33.75MHz Yes - L Yes 1024 x 768 48.4kHz 60Hz 65.0MHz Yes Yes Yes Yes 56.5kHz 70Hz 75.0MHz Yes Yes Yes Yes 60.0kHz 75Hz 78.75MHz Yes Yes Yes Yes 1152 x 864 67.5kHz 75Hz 108.0MHz Yes Yes Yes Yes 1280 x 768 47.8kHz 60Hz 79.5MHz Yes : Yes Yes 60.3kHz 75Hz 102.25MHz Yes = Yes Yes 1280 x 800 49.7kHz 60Hz 83.5MHz Yes Yes Yes Yes 1280 x 960 60.0kHz 60Hz 108.0MHz Yes Yes Yes Yes 1280 x 1024 64.0kHz 60Hz 108.0MHz Yes Yes Yes Yes 80.0kHz 75Hz 135.0MHz Yes Yes Yes Yes 1360 x 768 47.7kKHz 60Hz 85.5MHz Yes Yes Yes Yes 1400 x 1050 65.3kHz 60Hz 121.75MHz Yes Yes Yes Yes 1440 x 900 55.9kHz 60Hz 106.5MHz Yes Yes Yes Yes 1600 x 1200° 75.0kHz 60Hz 162.0MHz Yes Yes Yes Yes 1680 x 1050 65.3kHz 60Hz 146.25MHz Yes Yes Yes Yes 1920 x 1200" 74.0kHz 60Hz 154.0MHz Yes Yes Yes Yes Wide 1280 x 720 44.7kHz 60Hz 74.4MHz Yes Yes Yes Yes 1920 x 1080 66.3kHz 60Hz 148.5MHz Yes Yes Yes Yes 67.5kHz 60Hz 148.5MHz Yes Yes Yes Yes US TEXT 720 x 400 31.5kHz 70Hz 28.3MHz Yes Yes Yes Yes Sun 1024 x 768 48.3kHz 60Hz 64.13MHz L = - Yes 53.6kHz 66Hz 70.4MHz - = - Yes 56.6kHz 70Hz 74.25MHz - = - Yes 1152 x 900 61.8kHz 66Hz 94.88MHz L = - Yes 71.8kHz 76.2Hz 108.23MHz - = - Yes 1280 x 1024 71.7KHz 67.2Hz 117.01MHz = = = Yes 81.1kHz 76Hz 134.99MHz Ê = Ê Yes 1600 x 1000 68.6kHz 66Hz 135.76MHz : = : Yes

* Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed

+_ All are compliant only with non-interlaced. + Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input. + _ The frequency values for the Sun are reference values

ÆCompatible signal timing (AV)

No. Function No. Function No. Function No. Function 1 [Red video signal input 9 |+5V 1 [NC. 6 [Nc.

2 [Green video signal input | 10 [GND 2 |Transmitted data 7 INC.

3 |Blue video signal input 11 INC. 3 |Received data 8 |NC.

8 |[GND for blue video signal

Mounting Precautions

(For SHARP dealers and service engineers)

+ Wheninstalling, removing or moving the monitor, ensure that this is carried out by at least 3 people. (PN-R603: at least 2 people.)

+ Be sure to use a wall-mount bracket designed or designated for mounting the monitor.

+_ This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials such as plaster / thin plastic board / wood before starting installation.

+_ This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor. Install by the most suitable method for the material and the structure.

+ _ To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the thickness of the mounting bracket.

+ Do not use an impact driver.

+ When moving the monitor, be sure to hold the areas shown in the figure below. Do not hold the LCD panel. This may cause product damage, failure, or injury.

+ After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount. + Do not use any screw holes other than VESA holes for installation.