SNC-L200N - Surveillance Camera SAMSUNG - Free user manual and instructions

USER MANUAL SNC-L200N SAMSUNG

Illustration of a Samsung radio device with labeled buttons (no text or symbols on the device body)

AB68-00524B

* Read the "Safety Cautions" before using the product.

CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION :

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions.

1) This device may not cause harmful interference, and
2) This device must accept any interference that may cause undesired operation.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions.

Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plus. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a used, caution when moving the cart/apparatus combination to avoid injury from tip-over.

1. Unplug this apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
2. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Table of Contents

1. Product Overview	4
1.1 System Requirements	5
1.2 Content Checklist	7
1.3 Product and Accessory Checklist	8

1. Connecting

2.1 Connecting	10
2.2 Installing	10
2.2.1. To install on a wall surface (concrete and solid wall)	11
2.2.2. To install as a tabletop type	12
2.2.3. To install in other locations	12
2.3 PRI Sensor and Flash Movement	12

1. Netcam Configuration

3.1 Before Starting Netcam Configuration	14
3.1.1 IP Router Configuration	14
3.1.2 SNC Installer Installation	14
3.2 Netcam Configuration	16
3.3 Connecting to Netcam	20
3.3.1. Connecting from Internet	20
3.3.2. Connecting from Local Network	20

1. Using Smart Viewer

4.1 Connecting to Notcam	21
4.2 Installing ActiveX Control Program	21
4.2.1 Windows 2000 Users	21
4.2.2 Windows XP SP 2 Users	22
4.2.3 Local Network Environment not connected to Internet	23
4.3 Using Smart Viewer	24
4.3.1 Smart Viewer Function Buttons	24
4.3.2 Simple Player Program Guide	26

1. Smart Viewer Administration Menu

5.1 System Configuration Menu	31
5.1.1 System Information	32
5.1.2 Admin. Password	32
5.1.3 Access Configuration	33
5.1.4 User Registration	33
5.1.5 Video	35
5.1.6 Alarm Notification	35
5.2 Network Configuration	37
5.2.1 Network Configuration	38
5.2.2 PPPoE (ADSL)	39
5.2.3 Network Ports Configuration	39
5.2.4 View Network Status	40
5.2.5 Network Status Notification	40
5.2.6 DDNS Configuration	41
5.3 Utilities	42
5.3.1 Save Configuration	42
5.3.2 Reset	43
5.3.3 Factory Default	43
5.3.4 System Update	43

1. Netcam MultiViewer

6.1 Key Features	48
6.2 Requirements	49
6.3 Installing MultiViewer	50
6.4 Using MultiViewer	52
6.5 Setup	55
6.5.1 Registration	55
6.5.2 Viewer Setup	58
6.6 Print	59
6.7 Motion	61
6.8 Player (Playback)	63
6.8.1. File Open	64
6.8.2. Screen Size Switch	64
6.8.3. Various Playback and Search	64
6.8.4. Snap Shot	64
6.8.5. Print	65
6.8.6. Status Display	66
6.8.7. Log File	66

1. Product Overview

Product Overview

About Netcam

SNC-L200 is a network camera that can be monitored from a remote PC through various networks such as ADSL, Cable Modem. With a compact design, it fits perfectly into your interior environment.

SNC-L200 videos can be remotely monitored through a Viewer exclusively from Samsung. The camera Pan/Tilt control is also possible. And the Pre/Post Alarm videos can be saved to the remote PC when motion is detected.

Key Functions

• 1/4" 3.2 Effective Megapixel CMOS
- Presets up to 8 spots
- Pan/Tilt Control
- Image Monitoring with flash movements
- Motion Detection
- Corresponds to Various Communication Protocols ; TCP/IP, UDP, ARP, HTTP, SMTP, FTP, Telnet, DHCP, PPPoE
- Privacy Protection Function (Privacy button)

1.1 System Requirements

Peripheral Requirements
Single Channel Viewer	Minimum PC Requirements	CPU Pentium 4 1GHz or higherRAM Memory 256MB or higherVideo Memory 128MB or higherResolution 1024*768 or higherOS Windows 2000/XPWeb Browser Internet Explorer 6.0 or higher
	Recommended PC Requirement	CPU Pentium 4 1.5GHz or higherRAM Memory 256MB or higherVideo Memory 128MB or higherResolution 1024*768 or higherOS Windows 2000/XPWeb Browser Internet Explorer 6.0 or higher
Multi Channel Viewer	Recommended PC Requirements	CPU Pentium 4 2.4GHz or higherRAM Memory 512MB or higherVideo Memory 128MB or higherResolution 1024*768 or higherOS Windows 2000/XPWeb Browser Internet Explorer 6.0 or higher
Netcam Specifications
Server	Image Compression	JPEG
	Video Streaming Format	MJPEG
	Resolution	640*480 / 320*240 / 160*120
	Frame Rate	320*240 : Max, 30Fps640*480 : Max, 15Fps
	Authentication	ID/Password
Camera	Upgrade	Ethernet connection
	Remote Pan Angle	50° left/right max.
	Remote Tilt Angle	40° to +10°
	Maximum Pan/Tilt Speed	50°/sec
	Image Sensor	1/4" 320,000 Pixel CMOS
	Focus	Fixed 1m-infinity
	Flash LED	Range : 3m, Lux Value(1m) : 8.0 lux
	PIR Sensor	Range : 3m, Left/Right 30°, Up/Down 85°
Interface	Network Connection	Ethernet 10/100Base-T
	Network Service	Fixed IP, Cable Modem, ADSL, DHCP, IP Router
	Network Protocol	TCP/IP, UDP, DHCP, ARP, HTTP, Telnet, PPPoE, SMTP, FTP
Power	Power Adaptor	8.4V DC, 1A
	Power Consumption	5W (8.4V DC, 500mA)
Operating Temperature		0°C to +40°C Indoor Only
Dimension(W*H*D)		105mm*75mm*48mm
Weight		400g

You may download the latest version of Netcam SNC-L200 User Manual from Samsung Electronics home page at www.sec.co.kr. The Multi Channel View Guide is in the CD shipped with Netcam.

* Depending on the network environment or PC function, decrease in image transfer speed may occur.
* PIR Sensor detects temperature changes caused by the infrared ray that naturally emitted from human or animal. Therefore, a detection error or narrowing down of detection range may occur due to the effect caused by ambient temperature change and use of A/C or heater.

1.2 Content Checklist

Netcam and accessories are safely packed in the box. After purchasing the product, make sure you have all the following contents.

Diagram showing seven different electronic devices and accessories with numbered labels

① Netcam : 1 EA
② User Manual : 1 EA
③ CD:1 EA
④ Accessory Pouch : 1 EA

■Anchor-wall 16 x 3

2 EA

■Screw KAL-Black : 2 EA

⑤ Power Adaptor : 1 EA
⑥ Power Cable : 1 EA
⑦ CORE-FERRITE : 1 EA

Check carefully and make sure there are no missing or damaged components.

If any component is missing or damaged, contact the retailer where you purchased the product.

* SNC-L200 can affect EMI(Electro-Magnetic Interface),

so it is recommended to coil the CORE-FERRITE for use.

It is recommended to wind the LAN cable three times before use.

(The CORE-FERRITE is contained in SNC-L200 box).

1.3 Product and Accessory Checklist

Front

SAMSUNG ① ② ⑥ ③ ④ #RACCY ⑤

①Camera Lens Displays images entered from camera lens through the Viewer. Pan/Tilt control can be done through the Viewer.
②PIR Sensor The built-in PIR sensor detects object movements and outputs signals.
③Network LED Indicates Network link status. LED lights up when a proper network cable is connected to Netcam.

■ON: Network link complete

■Blinking : Receiving/Transmitting data

④Flash

Connected with PIR sensor.

It flashes for 5 seconds automatically when there is a movement.

Flash On/Off control can be done through the Viewer.

⑤Privacy Button for the Privacy protection.

When the button is pressed first time, the lens moved to outside of the operation range, so the screen is displayed in black. Press the button again to cancel the video transfer from the Netcam. Pressing the button yet again will return to initial status and the normal control will become available.

⑥Power LED Indicates Power supply status.

8

Video Netcam | SNC-L200

Back

Technical diagram of a device with numbered components, likely an electronic device or scanner

①DC Power Adaptor Please connect a DC 8.4V/1A.
②LAN Please connect a network cable (LAN cable).
③PRESET Set the Netcam setup value to the factory default status.

Press for more than 3 seconds during a normal operation (about

1 minute after power is on), Netcam setup value will change to

the factory default settings. Due to rebooting, it will operate after

1 minute

The existing setup values, such as IP, Administrator log on information, and upgrade Information will be changed to the factory default status. Please reset all the information to operate SNC-L200.

Please use authorized DC power adapters only. Using unauthorized devices may damage the product.

9

Video Netcam | SNC-L200

2. Connecting

Connecting

2.1 Connecting

INTERNET HUB Rear LAN Cable PC LAN Cable SNC L200 Rear DC INPUT

① Push downward and remove the cover located at the back of Netcam.
② Connect one end of the Ethernet cable to the router.
③ Connect the other end of the Ethernet cable to the back of Netcam.
④ Connect the power adapter and power cable to the power outlet and then connect them to the back of Netcam.
⑤ After the power is connected for 1 minute, make sure Netcam lens automatically moves.
⑥ Close the cover at the back of Netcam.

2.2 Installing

Install directly on the wall or on let it stand on a flat surface as a tabletop type.

You may install it where you want by using separate stands, such as wall mount.

(However, when using supplementary stands such as a wall mount to install, make sure the stand can be secured to the nuts on the back of the SET.

\*Precautions while installing Netcam

• When installing on the wall, make sure the location can withstand more than the SET weight (app. 1 kg).
• There is a falling hazard after the SET is installed on the wall. Make sure nobody comes close to it.
• The SET is intended or indoor use. Install it in a place where it cannot be reached by rain, water, or with less humidity.
• When installing using a fixed type stand and separate structures, make sure to secure them so they do not become loose from the nuts on the back of the SET.

10

Video Netcam | SNC-L200

2.2.1. To install on a wall surface (concrete and solid wall)

1. Drill two holes (Diameter: 5 mm, Depth: 35 mm) on the installation location using an electric driller. Vertical distance between the two holes should be 35 mm.

* It would be convenient for you to stick the enclosed label template on the installation surface and use it.

1. Insert the enclosed two plastic anchors to the holes (one each) and tighten the screws with a driver.

35mm

* To install on a regular wooden wall, refer to the figure above and tighten two screws with a driver.
3. Remove the cover from the back of the SET. Plug in LAN-CABLE and POWER CORD. Align the two to the groove of the cover, and then close the cover as shown in the figure below.

1. Align two grooves at the back of the SET to the pre-installed screws on the wall and hang the SET. Pull it slightly downward. The installation is complete.

11

Video Netcam | SNC-L200

ConnectingConnectii

2.2.2. To install as a tabletop type

1. Remove the cover from the back of the SET. Plug in LAN-CABLE and POWER CORD. Align the two to the groove of the cover, and then close THE cover as shown in the figure below.

1. Suspend the LAN-CABLE and POWER CORD to the groove of "A" portion. Let the SET stand.

2.2.3. To install in other locations

Remove the cover from the back of the SET. Plug in LAN-CABLE and POWER CORD. Align the two to the groove of the cover, and then close the cover. Follow the other installation methods to secure the CABLE.

* When using after securing the SET on a separate stand, make sure the stand can be secured to the nuts on the back of the SET.

2.3 PIR Sensor and Flash Movement

PIR SENSOR FLASH

When installing the set, consider operation / detection range of the PIR Sensor. When the PIR Sensor works the flash may function.

12

Video Netcam SNC-L200

Detection ranges of PIR SENSOR are as follows: Horizontal range: Approximately 40 degrees Vertical range: Approximately 85 degrees Detection distance: 5m(Max)

(Horizontal detection angle range)
(Vertical detection angle range)

Approximately 5m Approximately 40°

Approximately 10° 30.5"

* When the movement is fast, the horizontal detection distance may vary. * Please avoid installing the set in a place under the direct sunlight, a place expected considerable temperature change such as near to heater / air conditioning unit, a place produces high humidity / oil / smoke or stains such as in a cooking room, and a place having obstructions such as mirrors / glass that might cause erroneous sensor operation.

When PIR SENSOR moves, the illumination ranges of the FLASH LENS are as follows: Horizontal range: Approximately 67 degrees Vertical range: Approximately 67 degrees Illumination distance: 5m(Max)

(Illumination range)

Approximate 6m 92°

13

Video Netcam | SNC-L200

3. Netcam Configuration

Netcam Configuration

3.1 Before Starting Netcam Configuration

3.1.1 IP Router Configuration

IP router is needed if you want to use the Internet besides Netcam. You must configure IP router once so that Netcam can operate properly.

Whether you have an existing IP router or purchased a new one, you must configure Port Forwarding so that Netcam can operate properly.

Please refer to IP Router User's Manual.

* IP Address and Port set in the IP router will be needed later when you configure Netcam. Please do not forget them.

* If you remember the Subnet Mask, Gateway in the IP router connection status confirmation page, it would be helpful later when you install Netcam.

^ Port Forwarding

If you want to use Netcam via IP router, you need to allocate a unique port number to Netcam.

Numbers from 1 through 65535 can be used as port numbers. However, do not use the following port numbers.

FTP: 21

Telnet: 23

SMTP: 25

DNS: 53

POP3: 110

HTTPS: 443

ICQ: 4000

IRC: 6661-6667

To prevent the conflict between the port and other programs from happening, it's better to set the port number greater than 10,000.

3.1.2 SNC Installer Installation

You need to install the SNC Installer program from the installation CD shipped with the product.

SNC Installer searches Netcam on the local network, shows the unique MAC Address, and configures Netcam.

1. Insert the provided CD to the CD-ROM drive.

14

Video Netcam SNC-L200

1. Double click and run "SNC Installer.exe" from the CD-ROM.

Implementation of DOS Infrastructure This will install ESC Installer in your computer. It is recommended that you will all other programs while proceed with installation. Click (check) to continue installation. Do, click (cancel) to cancel installation. Next Cancel

1. Click "Next."

SNC installer will be installed to following folder. Click: Cramatic in begin installation to following folder, to install to a folder (file). Info. is for local files. Or, click (Browse) and make additional folder. Store needed: 2500 bytes Install folder: Save As: 123487698/888801.00 Store Install Cancel

1. Install starts.

Installation SIMC Installer Click Web/Work to boot installation, Installing for COM program Files/SIMC Installer Installing here: Progress: OK New Computer Technologies

15

Video Netcam | SNC-L200

1. Click "OK" when installation is complete.

Installation of SIMS installer Installation of SIMS installer completed. OK

3.2 Netcam Configuration

1. Double click and run SNC Installer.

File Edit View Favorites Tools Help Current Settings File Edit History Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit As Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit In Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Edit Out Show to Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From Show To Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From ShowTo Use From

Or click Start→Programs→SNC→Installer→SNC Installer.

16

Video Netcam | SNC-L200

1. When you run SNC Installer, the following screen appears.

File Address Server Name | IP Address | IP Type | HTTP Port | Mac Address | Modal | Status | Security Clear Close

- When the following window appears, click "Cancel Interception" will allow you to use it properly.

Windows Security Alert To help protect your computer... Windows Firewall has blocked more features of this program. Do you want to keep blocking this program? Name: Discovery Publisher: Unknown Keep Blocking Unlock Ask My Life Windows Firewall has blocked the program from according instructions from the internet to a network. If you can't change the program to hurt the publisher, you can unlock it. When should unlock a program?

1. Click "Search."

The following screen appears for several seconds.

BNC Provider Server Name | IP Address | IP Type | HTTP Port | Max Address | Model | Status CommandButton... Please wait for a few seconds

17

Video Netcam | SNC-L200

1. When the search for Netcam in the same router is over, the following message appears on the screen. Click "OK."

SME software Search Name In Search Type Import Find Marks Model Water CNCI BI ENRPF1000 AMERICAN Success Search First Complete OK

1. Select the Netcam you want from the screen where the search is complete. Right click "Edit."

SPTV Server Name IP address P Type MFTP Port Mus Address Mreal Status Go to Homepage Ctrl Search Cancel Close

1. "Network Option" screen appear.

* Before Staring Network Configuration If you connect Netcam using IP router, IP and Port cannot be automatically allocated. You must enter the numbers yourself using the IP router configuration program. For the correct configuration steps, please refer to IP Router User's Manual. Refer to "3.1.1 IP Router Configuration" for details.

IP Type Source Name Network Address IP Address Network Address DNS DNS2 IP No.1 IP No.2 IP No.3 IP No.4 IP No.5 IP No.6 IP No.7 IP No.8 IP No.9 IP No.10 IP No.11 IP No.12 IP No.13 IP No.14 IP No.15 IP No.16 IP No.17 IP No.18 IP No.19 IP No.20 IP No.21 IP No.22 IP No.23 IP No.24 IP No.25 IP No.26 IP No.27 IP No.28 IP No.29 IP No.30 IP No.31 IP No.32 IP No.33 IP No.34 IP No.35 IP No.36 IP No.37 IP No.38 IP No.39 IP No.40 IP No.41 IP No.42 IP No.43 IP No.44 IP No.45 IP No.46 IP No.47 IP No.48 IP No.49 IP No.50 IP No.51 IP No.52 IP No.53 IP No.54 IP No.55 IP No.56 IP No.57 IP No.58 IP No.59 IP No.60 IP No.61 IP No.62 IP No.63 IP No.64 IP No.65 IP No.66 IP No.67 IP No.68 IP No.69 IP No.70 IP No.71 IP No.72 IP No.73 IP No.74 IP No.75 IP No.76 IP No.77 IP No.78 IP No.79 IP No.80 IP No.81 IP No.82 IP No.83 IP No.84 IP No.85 IP No.86 IP No.87 IP No.88 IP No.89 IP No.90 IP No.91 IP No.92 IP No.93 IP No.94 IP No.95 IP No.96 IP No.97 IP No.98 IP No.99 IP No.100

1B Video Netcam | SNC-L200

Netcam ConfigurationNetcam (

IP Type		Click "Static."■When Netcam is connected to IP router, it is considered having a static IP internally.
Server Name		Enter Netcam's name. The name can be a combination of numbers and letters up to 20 characters. However, characters such as #, ' : : cannot be used.
Network	IP Address	Enter the allocated IP address of Netcam that has been entered in the Port Forwarding configuration during IP router configuration.
	Netmask	Enter the Subnet mask of IP router.
	Default Gateway	Enter the Default Gateway of IP router.
	DNS1/DNS2	Use default value for DNS server whenever possible.■Default value is 168.126.63.1/168.126.63.2.
HTTP Port		Enter the Port number of Netcam that has been entered in the Port Forwarding configuration during IP router configuration.
Authentication Key		Enter the Netcam Administrator Password.

Save Configuration Option	Save All Configuration	Select it to save all configuration values.
	Save Only Network Configuration	Select if to save network configuration values only.
	Not Saving	Select it to configure only but not saving to the internal Flash Memory.

Click "Set" button to apply the configuration to Netcam and save according to the "Save Configuration Option." During IP configuration, you cannot connect to Netcam. Please close Internet Explore window, wait for 1 minute, and then connect to it again.

Click "Cancel" button to cancel the configuration values.

1. Click "Set" button. The following window appears. Click "Yes."

1. The following screen appears for several seconds.

19

Video Netcam | SNC-L200

Netcam Configuration

1. Click "OK" button when network configuration is complete.

3.3 Connecting to Netcam

3.3.1. Connecting from Internet

1. Run Internet Explorer from your PC.
2. Enter "http://IP Address (or URL): Port number" in the address field, then press "Enter."
   The URL is composed of lower case "w," the last six digits of Netcam's MAC Address, and the DDNS Server Address.

Example: http://IP Address: Port number

Or http://(Last six digits of MAC Address).websamsung.net: Port number

* MAC Address can be identified from the label at the back of Netcam.
* When the Port number is 80 (default value), you don't need to enter port number at the end of the address.

Example: http://168.219.13.250

Or http://wfff06b.websamsung.net

* Internet Service Provider (ISP) may block the port that has the number 80.
You need to enter the port number when it is a number other than 80.

Example: http://168.219.13.250:8080

Or http://wfff06b.websamsung.net: 8080

3.3.2. Connecting from Local Network

1. Run the SNC Installer, select the Netcom you want from the screen where the search is complete, and then right click it. You may see the Smart Viewer of the Netcam by selecting "Go to Homepage."

Power Access IP Options IP Type MUT For Help Active/Help Other 1.0 Access Copy Next

20

Video Netcam | SNC-L200

4. Using Smart Viewer

4.1 Connecting to Netcam

1. Open the Internet Explorer, and enter "http://IP Address (or URL): Port number" in the address field, then press "Enter" to connect to Netcam.
2. Network password screen appears. Enter Username (U) and Password (P), then click "OK" button. The initial Username is "root," and the password is "root."

Connect to wff068.webamsung.net About User name: root Password: ****** Remember my password OK Cancel

4.2 Installing ActiveX Control Program

When first connected, "Security Alert" window may appear.

If you want to see videos (Motion JPEG), you need to install ActiveX Control program.

* When first connected, the download time for ActiveX may vary based on the network environment.

4.2.1 Windows 2000 Users

In case of having security warning shown below, click on "Yes".

Security Warning Do you want to install admin "Microsoft Internet Explorer" signed on 26.4.15.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.2 ENSC ELECTRONICS CO., Ltd. Publisher authenticity verified by VeriSign Class 3 Code Spring 2001 Co. Custom: ENSC ELECTRONICS Co., Ltd; says that the content is safe. You should only install your this content if you must establish the ELECTRONICS CO., Ltd. No note that secretion. □ Always first content from ENSC ELECTRONICS Co., Ltd. Yes No Move Info

21

Video Netcam | SNC-L200

4.2.2 Windows XP SP 2 Users

1) According to ActiveX Download Policy of Windows XP SP2, the following screen appears.

SAMSUNG Networks Camera - Microsoft Internet Explorer File Edit View Favorites Tools Help Search Favorites Access: 10x (4008) webservering.1639999999999999999999999999999999999999999999999999999999999999999999999999999999999999999999999999999 Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUNG ELECTRONICS Co., Ltd." Click here to install... Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUNG ELECTRONICS Co., Ltd." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUNG ELECTRONICS Co., Ltd." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUNG ELECTRONICS Co., Ltd." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUNG ELECTRONICS Co., Ltd." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUNG ELECTRONICS CO., Ltd." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUNG ELECTRONICS CO., Ltd." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUNG ELECTRONICS CO., Ltd." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUNG ELECTRONICS CO., Ltd." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUN ELECTRONS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SAMSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDamViewInstall from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following ActiveCard: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following active card: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following active card: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following active card: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to install the following active card: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to insert the following active card: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to insert the following active card: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to insert the following active card: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC." Click here to insert the following active card: "WEEDam view Install from SANSUN ELECTRONICS CO., LLC" .

2) Click ActiveX Installation message.

3) Click "ActiveX Control Installation."

MARTUNG Networks Corp - Microsoft Internet Explorer File Edit View Favorites Tools Help http://www.martung.com/ <|vision_start|> Dominant Web Services (http://www.martung.com) Diktar: Install Web Service (http://www.martung.com) Information for Web

4) Click "Installation" when the "Security Alert" window appears as below. ActiveX Control needed for running Smart Viewer will be automatically installed on PC.

Do you want to install this software? Name: Samsung Electric Ltd Pulsor: SAMSUNG ELECTRONICS Co., Ltd. More options: Install Don't Install While the first from the Internet can be useful, this type can potentially harm your computer. Only listed software from software you have, what's the that!

4.2.3 Local Network Environment not connected to Internet

1) When using in a local network environment that is not connected to Internet, click "Smart Viewer For Network Camera" button on the right top of the screen.

SAMSUNG Networks Camera - Microsoft Internet Explorer File Edit View Insert Help Tools Help Search Favorites Access: http://www.sAMSUNG Networks This document is required to provide an email client for the website. Email: https://www.sAMSUNG Networks Co., Ltd. or www.sAMSUNG Networks Inc. Smart Networks Web Network Camera Find a new available web page from the website. Email: https://www.sAMSUNG Networks Co., Ltd.

2) Click "Download."

3) Click "Run."

4) Click "Run."

4.3 Using Smart Viewer

Smart Viewer runs as the picture below when connecting to Netcam through Internet Explorer.

You can save and playback transferred images through the Smart Viewer, and change the settings of Netcam remotely using Web Admin Mode.

4.3.1 Smart Viewer Function Buttons

1 23/SEP/2005 AM 11:03:28 SAMSUNG DIGITDAI Prime1 ① ② ③ ④ ⑤ ⑥ ⑦

① Download Icon
Click the icon to manually install the Active X control on a PC to run the Smart Viewer.
②Administrator Mode
Admin: Netcam Admin Window appears. You may setup all the system settings. Refer to "5. Smart Viewer Administration Menu"
③Preset Icons
Preset 1 : Select Preset numbers. You may choose from 1-8.
Preset Go: Moves Pan/Tilt of the camera as the data saved in the selected Preset number.
Preset Delete: Deletes the Preset Data in the camera.
Preset Save: Save the Preset Data to the camera.

④Pan/Tilt Icons

Controls movements related to Pan/Tilt of the camera.

Clicking the icon will move to the direction the icon shows.

Up/Left

Left

Down/Left

Up

Down

Up/Right

Right

Down/Right

⑤Function Icons

Flash: Enables the Flash On/Off function.

When Flash On is selected, it flashes for 5 seconds then is off for 30 seconds. During this Flash Off mode Flash On is disabled.

PIR: Enables the PIR Sensor On/Off function.

It flashes for 5 seconds automatically when there is a movement.

Save Path: Use it to change directory of the file saved during recording. When

clicking Rec, the file recorded will be saved in "C:\Program

Files\Samsung\Netcam_WEB\00-30-6f-ff-f0-50 (unique MAC Address)"

but the directory can be changed using "Save Path" button.

Capture: Use it to save a still video from live videos to a JPEG file.

⑥Display Size Icons

Small: Changes the screen size to 160x120.

Normal: Changes the screen size to 320x240.

Full: Changes the screen size to 640x480.

⑦Playback Icons

Rec: It records the images currently transmitting through the network. If a user moves to the Admin Mode page while recording, the recording stops. Recording may be interrupted if another PC downloads ActiveX Control while recording.

- 1 recording time is about 10 minutes.

- The length of the recorded file is about 10 minutes.

Play: Plays back the recorded file.

When clicking Play, the list of recorded files appears. Select and click the file you want to play back, then the Simple Player screen appears.

Stop: Stops recording and switch to Live screen.

4.3.2 Simple Player Program Guide

Simple Player is a playback screen where the recorded video files can be played back, saved, re-edited, enlarged, compressed, and printed.

1. Click ▶ Play button on the Smart Viewer screen.

2. The file list appears.

File My Documents Desktop My Documents My Computer My Network Player File type: 200005E_11.dsn236s File of type: Microsoft/ Auto Files Open Cancel

1. Select the desired file and click "Open." Simple Player screen appears.

26

Video Netcam | SNC-L200

4.3.2.1 About the Menu Bar

Simple Player File Edit View Tools Help 00:24:87:49 2005/07_15h3m28s.8p Ready 10.63%

①Menu Bar

File

*File Open: You can select and play back the files recorded through Smart Viewer.

*Print: Contains Print Setup menu.

Control: Contains Playback menus (Back, Play, Pause, Stop, Next Frame, Previous Frame, Next File, Previous File).

Zoom: Zoom In, Zoom Out, Actual Size

Tool: Snapshot menu

- Help: Simple Player version number and copyright

② File Open: You can select and play back the files recorded through Smart Viewer.

③Playback Menus

Back

Play

Pause

Stop

Previous Frame

Next Frame

Previous File

Next File

27

Video Netcam | SNC-L200

④Speed: You can set the scroll bar playback speed. Settings: x0.1, x0.2, x0.5, x1, x2, x4, x8, x10

⑤Zoom Related Direct Menu Icons

⑥Snapshot Icon (Refer to 4.3.2.2 Snapshot)
⑦ Print Icon (Refer to 4.3.2.3 Printing)
⑥Scroll Bar: Click a playback-related button, then the scroll bar moves. Click the mouse in the scroll bar area, then it stops temporarily. You can drag the scroll bar with the mouse.

4.3.2.2 Snap Shot

1. Click the Snapshot icon (☐) on the menu bar at the top of the screen or click "snapshot" in the Tool menu.

The directory screen to save the file appears.

Save Save in: CD3061-1050 MyRecent Documents Desktops My Documents My Computer File name: Save as true: JPEG 6 Filed (log * pc) Save Cancel

1. Save the file to the designated folder.

*It will be saved as a jpg file and can be edited in the paint tool in the accessory program group.

2B

Video Netcam | SNC-L200

4.3.2.3 Printing

1. Click the Print icon ( ) on the menu bar at the top of the screen.

The description screen appears.

1. Click "Memo" to enter the description to be recorded in the printer and click OK.

1. Click "Setup" to select the printer and printout.

Properties Name: Samsung M.1700 items Status: Image Type: Samsung M.1700 items Width: 25 px Dimensions: Samsung M.1700 items File size: 1 pt Color: Number of colors: OK Cancel

29

Video Netcam | SNC-L200

5. Smart Viewer Administration Menu

Smart Viewer Administration Menu

http://wff9068.webcams.org.net:8000 SAMSUNG Network Camera Admin - Microsoft Internet Explorer System Configuration Network Configuration Utilities System Configuration System Information Configuration of System Information... Admin. Password Change administrator's password. Access Limitation Configuration to permit the access according to user level. User Registration Add, Edit, Delete User ID & Password. Video Configuration of video size and quality. Alarm Notification Configuration to notify alarm through email.

Admin Menu	Sub Menu
System Configuration	System Information
	Admin. Password
	Access Limitation
	User Registration
	Video
	Alarm Notification
Network Configuration	Network Configuration
	PPPoE (ADSL)
	Network Ports
	View Network Status
	Network Status Notification
	DDNS Configuration
Utilities	Save Configuration
	Reboot
	Factory Default
	System Update

30

Video Netcam | SNC-L200

5.1 System Configuration Menu

System Configuration System Information: Configuration of System Information... Admin. Password: Change administrator's password. Actions Limitation: Configuration to permit the access according to user level. User Registration: Active, Edit, Delete User ID & Password. Video: Configuration of video size and quality. Name Notification: Configuration to notify alarm through email.

System Information	This is the menu to configure System Information.
Admin. Password	This is the menu to change Administrator password.
Access Limitation	This is the menu to control user access.
User Registration	This is the menu to add, modify, and delete user ID and password.
Video	This is the menu to configure the resolution and quality of a video image.
Alarm Notification	This is the menu to configure image transfer via E-mail when alarm occurs.

31

Video Netcam | SNC-L200

5.1.1 System Information

System Information

Server Name	Configure Netcam name.The name can be a combination of numbers and letter up to 20 characters. However, characters such as #, ', ", : cannot be used.
Model	Displays "NETWORK CAMERA."However, only reading is available. Writing is prohibited.
Version	Shows System and Web program version of Netcam.However, only reading is available. Writing is prohibited.

5.1.2 Admin. Password

Administrator's Password Configuration

Notice: The password must be alpha-numeric, within 4×20 characters.

Administrator's ID	Administrator's ID is always "root."
Old Password	Password at initialization is "root."
New Password	Enter the password you want to change. Password can be a combination of numbers and letters up to 4~20 characters.
Confirm Password	Enter the password you want to change one more time.

32

Video Netcam | SNC-L200

5.1.3 Access Configuration

Access Limitation Configuration

○ Full Access(Male and control camera without permission)

○ United Access(In attendance with an user's permission.)

Maximum Frame Rate 30%

Notice: After setting up the parameters and clicking Apply button, the changed setting value will be applied to the new access of this server. Please refresh your web browser or no access to the server.

Full Access	Any one can view images by connecting to Smart Viewer without going through the authentication process.You cannot control Camera's basic operations when it is connected in Full Access.
Limited Access	When a regular user tries to connect to Smart Viewer, he/she will be connected through the authentication process.
Maximum Frame Rate	You may configure frame per second for image transfer as 1fps/2fps/5fps/10fps/15fps/30fps/.When the image size is 640*480: Max. 15fpsWhen the image size is below 320*240: Max. 30fps

5.1.4 User Registration

User Registration (Add)

Add	This is the menu to register users.
User ID	Enter new user ID.
Password	Enter new user password.
Confirm Password	Enter new user password one more time.
Full Name	Enter new user name.

* You cannot control Camera's basic operations when you logged in as a user ID other than the Administrator.

33

Video Netcam | SNC-L200

User Registration (Edit)

Add Edit Delete User ID Select User Password Confirm Password Full Name Back Apply

Edit	Click the User ID that you want to change the information from the "Select User ID" box of the User ID. You may change registered information, such as Password and Full Name, etc.

User Registration (Delete)

Add Edit Delete inyoung tank Back Delete

Delete

This is the menu to delete registered users.Click the User ID you want to delete, then click "Delete" button.

Smart Viewer Administration MenuSmart View

5.1.5 Video

Video Configuration

Image Size	This is the menu to select the resolution of video data being transferred. You may set the size as 160*120, 320*240, or 640*480.
Image Quality	This is the menu to configure the quality of video image being transferred. You may set as High, Normal, or Low.
Hue	This is the menu to adjust Hue. (-10~10)
Saturation	This is the menu to set Saturation. (-10~10)
Contrast	This is the menu to set Contrast. (-10~10)
Brightness	This is the menu to set Brightness. (-10~10)
Power Frequency	It selects 60Hz in the 60Hz power frequency area and 50Hz in the 50Hz power frequency area respectively.

5.1.6 Alarm Notification

Alarm Notification

Service SMP server address Authentication Login User ID Password Sender (Email) E-mail address 1 E-mail address 2 E-mail address 3 E-mail address 4 Image Count 0 Back Apply

Service	This is where to configure whether using this Service or not.Selecting "Enable" will allow you to use "Alarm Notification" function.
SMTP server address	It means Simple Mail Transfer Protocol (SMTF) Server address.This address is used to transfer E-mails.Enter the after @ part of the Email Address you use.
Authentication Login	It is recommended to select "Enable."
User ID / Password	When using the Authentication Login, enter User ID and User Password of the sender's Email Address. They are usually designated at the time the mail service is subscribed.
Sender (E-mail)	Enter the sender's Email Address.Do not use a bogus name because the mail server often check it to block Spam mails.
E-mail address 1~4	Up to 4 Email Addresses can be registered to receive video data.
Image Count	Up to 5 images can be sent with a 0.5-second interval each. The number of image count will be shown.

Assuming the sender's Email Address is "[e-mail]," and the Password is "1234567," the "Alarm Notification" should be configured as follows.

Alarm Notification

Service ○ Enable ○ Disable SMTP server address smtp.samsung.com Authentication Login ○ Enable ○ Disable User to lmourng.hes Password ********** Sender (Email) [e-mail] Email address 1 [e-mail] Email address 2 [e-mail] Email address 3 [e-mail] Email address 4 Image Count 3 x Back Apply

Smart Viewer Administration Menu Smart View

5.2 Network Configuration

Perform general network configuration. If network configuration is not done properly, you cannot to transfer images via Internet Explorer or configure Netcam on the web. Please ask your network administrator and enter the following setup information correctly. To apply the settings to Netcam, you must click "Apply" button.

http://wff/068.webamsung.net:8888 - STATUNG Network Camera Admin - Microsoft Internet Explorer System Configuration Network Configuration Network Configuration PPR(PRT)... Network Ports View Network Status Network Status Notification CPB3 Configuration Utilities Network Configuration Network Configuration of Network HP, network, network, (A51) PPR(PRT)... Network Ports Modification of HTTP port number View Network Status View of network status Network Options Notification CDP3 Configuration Configuration of DPW5. Configuration of DPW5.

Network Configuration	This is the menu to set "Static IP" or "DHCP."
PPPoE(ADSL)	This is the menu to set PPPoE (ADSL).
Network Ports	This is the menu to set "HTTP Port."
View Network Status	This is the menu to view current system network status.
Network Status Notification	This is the menu used to notify the information of IP Address that is dynamically allocated, such as DHCP or PPPoE.
DDNS Configuration	This is the menu used to set DDNS.

5.2.1 Network Configuration

1) Static IP

When Netcam network configuration is Static IP (Public IP, Private IP), you may set the Static IP Address.

If you want to set Static IP, you must set IP Address, NetMask, Gateway, DNS 1, DNS 2, etc. Generally, the network administrator administers these items. You need to contact the network administrator and allocate them accordingly.

Network Configuration : Static IP

Static IP DHCP Client IP Address 168.219.40.68 NetMask 255.255.256.0 Gateway 168.219.40.1 DNS 1 168.126.63.1 DNS 2 168.126.63.2 Back Apply

2) DHCP IP

Choose it when Netcam network configuration is a Dynamic IP.

In DHCP, the IP Address allocation process occurs automatically. Therefore, IP Address may change continuously. You may use it in parallel with DDNS, or use Network Status Notification to enter to the Address allocated to the equipment.

Network Configuration : DHCP IP

3B

Video Netcam | SNC-L200

5.2.2 PPPoE (ADSL)

Choose it when Netcam network configuration is ADSL. In PPPoE (ADSL), the IP Address allocation process occurs automatically like in DHCP. Therefore, IP Address may change continuously. You may use it in parallel with DDNS, or use Network Status Notification to enter to the Address allocated to the equipment. In addition, since the Authentication process is included, you need to setup User ID, User Password, and Confirm Password. These can be designated or allocated when you subscribe the service from your ISP.

PPPoE(ADSL)

Service Emails Disagree User ID: email User Password: ****** Confirm Password: ****** DNS 1: 168.126.63.1 DNS 2: 168.126.63.2 Back Apply

5.2.3 Network Ports Configuration

It's Daemon Port Number of the HTTP (Hyper Text Transmission Protocol) Server. The default standard value is 80.

Network Ports Configuration

39

Video Netcam | SNC-L200

5.2.4 View Network Status

This is where you may verify the Network Status of your current system. Information commonly used in all interfaces (Ethernet 0 & PPPoE) is shown in Common Status, others are shown in Network Status by each interface.

Network Status Common Status Gateway 106-27140.0 DNS 1 106-3533.1 DNS 2 106-3533.3 LAN Status IP Address 102-27643.00 Network 106-225295.0 MAC Address 102-58-IP-PC-0.0 PPPIU Status Connection Status Link to drive IP Address Network Rate Relaid

Common Status	Displays the status of Gateway, DNS 1, and DNS2.
LAN Status	Displays the status of IP Address, Netmask, and MAC Address.
PPPoE Status	Displays the connection status of current PPPoE.

5.2.5 Network Status Notification

This is a service prepared to notify the IP Address, such as PPPoE or DHCP that is dynamically allocated. This service will be sent to a designated email address the moment when the IP Address allocation by PPPoE or DHCP is complete. Each item is the same as the text of "Alarm Notification," and the user may enter any text that will be added the email. You may enter up to 50 characters per line.

Network Status Notification Voi Nomenclature Enable C Delete C SMTP Server Authentication Loop mobile O Inname O User ID Password Sponsor Recipient's Email Address Recipient's Email Address Recipient's Email Address User-defined Message Bank Apply Rated

40 Video Netcam | SNC-L200

Assuming the sender's email Address is "[e-mail]," and the Password is "1234567," the "Network Status Notification" should be configured as follows.

Network Status Notification Mail Notification SMTP Server Authentication Login User ID Password: Sender Recipient's Email Address Recipient's Email Address Recipient's Email Address User-defined Message SNC-LDD Network Status Send Apply Reload Send Send Send

5.2.6 DDNS Configuration

This is a function that automatically changes the IP Address to the unique name that Netcam has, and then connect to it. DDNS server is websamsung.net. Domain name is w.websamsung.net, where w is the last six digits of MAC Address.

DDNS Configuration Service Enable Disable DDNS Server www.samsung.net Note The domain none of this system is www.samsung.net Back Apply

41 Video Netcam | SNC-L200

5.3 Utilities

Save the user configuration to the flash memory or configure the rebooting or updating method.

http://aftf364 wabnemung.sxt.8388 - SAMSUNG Network Camera J Admin - Microsoft Internet Explorer System Configuration Network Configuration Utilities Store Configurations Rebuild Factory Default System Update Llibles Save Configuration Project Factory Default Design Update Save configuration to flash memory. Replace the system. Factory default Factory default the system. Update web or firmware.

Save Configuration	The is the menu to save configuration to the flash memory.
Reboot	This is the menu to reboot the system.
Factory Default	This is the menu to set the system to the factory default.
System Update	This is the menu to update the system.

5.3.1 Save Configuration

It saves the configuration to Netcam's flash memory so the user configuration stays after rebooting or the power is off.

Save Configuration

• Save Configuration is required to save all of new configuration in the system. Otherwise, no new configuration will be saved and effective.
• If you do not want to save your new configuration, do not click 'Save' button.

Save

42

Video Netcam SNC-L200

5.3.2 Reboot

This is used when the user wants to reboot the system.

During rebooting, you cannot connect to Netcam. Please close Internet Explore window, wait for 1 minute, and then connect to it again.

Reboot

System reboot is highly and strongly recommended to applied all new configurations properly to the NETWORK CAMERA system

Reboot ^(1)

5.3.3 Factory Default

This is used to reset all the setup values to factory default conditions.

Factory Default

All of setting will be revert back to factory default except IP address, if you press "Factory Default" button.

Factory Default

5.3.4 System Update

This is the Utility Menu to upgrade the system when an upgraded system software is released.

There are two types of update: Normal Update and All Update.

System Update

Normal [System, Web] Update

Start

MI (Kemal, Ramdisk, System, Web) Update

Start

In general, there is usually no "All Update." Instead, "Normal Update" is generally used.

* The latest software version of SNC-L200 can be downloaded from Samsung's website http://www.sec.co.kr.

43

Video Netcam | SNC-L200

1. Click "Start" button from "Normal Update."

1. Click "OK" when "Do you want to upgrade this system?" message appears.

1. Click "Yes" when "The web page window you are watching will be closed. Do you want to close the window?" message appears.

1. Click "Find" when the following window appears.

http://163.2019.41.008 - Update System Image - Microsoft Update System Image Please upload a System Image "system"... Select for: Browse... Preview Visit Stop Case Insurer

1. Find the directory where the file for updating is saved, and then select the system file.

Choose File Look in uplore system-050921.exe web-050912.exe My Record Documents Desktop My Documents My Computer My Network Process File name: system-050921.exe File of type: AHTex (*.*)

1. Click "Next" button to upload the system file.

Update System Image Please upload a System Image "system*". Select File: C:\MSCI.UFC\Reference\Browse Previous Help Skip Done © 2019-01-10E

1. Click "Next" button when file upload is complete. system*.tar.gz file will be updated.

File Information File Name: system 000921.tar-62 File Size: 392 KB Preview Next Cancel Date ©/Record

Smart Viewer Administration MenuSmart View

1. When the system file update is complete, the window to update the web file appears. Click "Find."

http://60.219.41.108 - Update Web Image - Microsoft L Update Web Image Please upload a Web Image "web1". Select file: Browse Prints... Copy... Skip Date Internet

1. Find the directory where the file for updating is saved, and then select the web file.

C:\Users\File Windows My Documents My Computer My Office My Home My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Expanded My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Explorer My Internet Excel

1. Click "Next" button to upload the web file.

Update Web Image Please upload a Web Image "web"... Select the C:\WINDOWS\Microsoft\Browse... Previous Next Skip Core Cancel

46 Video Netcam | SNC-L200

1. Click "Next" button when file upload is complete. web*.lar.gz file will be updated.

File Information File Name: mt-05.912.txt File Size: 163.45 Import Next Cancel Date Home

1. When web file update is complete, the following message appears. Click "Reboot!!" button.

App: 0746-219.43.118 Update Date: Microsoft Internet Update Date: Please reboot this system. Hello! Save Help

1. Click "OK" from the following message. Netcam will be rebooted. During rebooting, you cannot connect to Netcam. Wait for 1 minute, and then connect to it again.

47

Video Netcam | SNC-L200

6. Netcam MultiViewer

This Netcam MultiViewer can connect up to 16 channels. It provides various functions, such as live video, recording, playback and search, alarm system connection, etc.

6.1 Key Features

- Connects to Netcam with up to 16 channels; Live image and recording available

- Pan/Tilt Function

- Preset (1–8) Function

● Motion Detection Connected Recording

- Motion Detection Connected Recording

- Various Screen Display

- 1, 4 (4 pages), 9 (2 page), and 16 Screen Displays

- Full Screen Function

- Sequence Function

- Sub Title Show/Hide Function

- Image Print Function

- Still video Print (Recorded video)

- Quick Time Print (Live video)

- Screen Capture Function

- Video Search Function

- Small, Normal, Large, Full Playback Functions

- 3x Speed FF/Rew Search Function

- Still and video One at a Time Fine Search Function

- Log file

- Disconnect, Reconnect Time Display

- Motion Detection List Occurrence Time Display

Netcam MultiViewer

6.2 Requirements

Recommended Peripheral System Specifications

Network Environment	10Base-T LAN (RJ-45)- Static IP-Cable Modem (DHCP)- ADSL (PPPoE)- Sharer (IP Router)- Private Network
PC Specifications	CPU	8CH : Pentium 4 2.0GHz or higher16CH : Pentium 4 2.4GHz or higher
	RAM (Memory)	512MB or higher
	Video Memory	64MB or higher
	Resolution	1024 x 768 or higher
	OS	Windows 2000/XP- Service Pack Installation is recommended

The minimum possible recording time of this device is measured based on the ideal network condition.

If the network condition is not favorable, or it's a dynamic IP (cable modem, ADSL, etc.) and if the number of connected channel is decreased, the recording time will increase.

*Hard Disk Measurement Standard

1) 40G: Windows OS 5G, based on 30G excluding the reserved 5G – 139 hours
2) 80G: Windows OS 5G, based on 70G excluding the reserved 5G - 325 hours
3) 120G: Windows OS 5G, based on 110G excluding the reserved 5G - 511 hours

When programs in addition to Windows OS are installed, the minimum recording time may be reduced.

6.3 Installing MultiViewer

1. Insert the CD came with Netcam to CD-ROM drive.
2. Double click and run "NetworkCameraMV_Setup.exe" from the CD-ROM.
3. Click "Next."

Presets for Network Commands MasterPlayer Does all install Network Commands MasterPlayer on your website. For a recommended first principal of other components, then provide a registration. Click to create or continue installation. In any context in case of installation. Next Cancel

1. Click "Install."
   

Installation of Network Camera Module - Selection Network Camera Module will be installed to Windows Media. This installed is the installed module in the following order: to install a network cable. Additional details include: on the network cable selected within the media. Space media: 1.0000000000 Install User Microsoft Windows 20000000000 Browse Install Cancel

1. Install starts.
   

A Configuration of Network Camera Modulator Linking Network Camera Modulator Click to Start at start installation. Linking to: 100% from the Network Camera Modulator Linking to: ASO Modulator Project: 50%

1. Click "OK" when installation is complete.
   

Inclustation of Network Camera Multiplexer Inclustation of Network Camera Multiplexer accomplished.

Network Camera Help Provider File Edit View Insert Tools Help Search Options Name: C:\Network Camera Help Provider C:\Network Camera Help Plus Data Modified 2.03 Description 2.04 Description 2.05 Description 2.06 Description 2.07 Description 2.08 Description 2.09 Description 2.10 Description 2.11 Description 2.12 Description 2.13 Description 2.14 Description 2.15 Description 2.16 Description 2.17 Description 2.18 Description 2.19 Description 2.20 Description 2.21 Description 2.22 Description 2.23 Description 2.24 Description 2.25 Description 2.26 Description 2.27 Description 2.28 Description 2.29 Description 2.30 Description 2.31 Description 2.32 Description 2.33 Description 2.34 Description 2.35 Description 2.36 Description 2.37 Description 2.38 Description 2.39 Description 2.40 Description 2.41 Description 2.42 Description 2.43 Description 2.44 Description 2.45 Description 2.46 Description 2.47 Description 2.48 Description 2.49 Description 2.50 Description 2.51 Description 2.52 Description 2.53 Description 2.54 Description 2.55 Description 2.56 Description 2.57 Description 2.58 Description 2.59 Description 2.60

6.4 Using MultiViewer

* You need to click 📞 to register the Netcam to be displayed in Setup first. (Refer to 6.5 "Setup.")

15/SEP/2005 09:00:51 SAMSUNG DIGITUM Insert

1. 168.219.41.189 Connect & Netcam list

IP address of the Netcam or the Domain Name list that are registered to the setup property appears. Select the Netcam IP address to display from the list box and then click the "Connect" icon to display the video from the selected Netcam. Image of the Netcam will be displayed.

If you want to display several images, repeat the step described above.

* One image per one channel will be displayed consecutively.

Displays the date (dd/mm/yyyy) and current time.

1. 1Ch

Displays the image of selected channel.

When you press the button first time, the image displayed is the size setup in the Netcam (640*480/320*240/160*120).

If you click the button again, the image will be displayed in full screen.

52

Video Netcam | SNC-L200

Netcam MultiViewerNetcam MI

1. 4Ch

Displays 4 screens with the selected image included.

When all 16 channels are connected, they will be divided into 4 pages each and then displayed.

If one of the 1-4 channel images is been selected, the first page will be displayed. If one of the 5-8 channel images is been selected, the second page will be displayed. Similarly, the third or fourth page will be displayed.

1. 9Ch

Displays 9 screens with the selected image included.

When all 16 channels are connected, they will be divided into 2 pages each and then displayed. However, the second page will display 7 images.

If one of the 1-9 channel images is selected, the first page will be displayed. If one of the 10-16 channel images is selected, the second page will be displayed. The second page will display images of 7 Channels only.

1. 16Ch

16 screens will be displayed.

This is a mode to see entire images because all images of 16 Channels will be displayed.

1. Full

This is a mode that displays only menu icon or images without the Viewer frame regardless the actual image size. This mode is used to view images only.

If you want to exit from this mode, you may do so by pressing the "Esc" key on the keyboard of your PC, and return to the menu icon or the original 1, 4, 9, 16 screens with the Viewer frame.

1. Sequence

Images connected to the Viewer will be switching consecutively and displayed.

- 1 Screen: Registered images switch consecutively 1 Channel at a time.

- 4 Screen: 4 images are allocated to 1 page, and then switch to 4 pages consecutively.

- 9 Screen: 9 images become 1 page, and the remaining 7 images becomes 2 pages, and then switch consecutively.

- 16 Screen: No consecutive switching occurs.

If "Viewer Setup → Sequence time → Single" is clicked, the registered images switch consecutively 1 channel at a time.

If you want to stop the consecutive switching, you may do so by pressing the 1, 4, 9, 16 Screen Display icons.

1. SNC Installer

It runs SNC Installer.

53

Video Netcam | SNC-L200

Setup

Refer to "6.5 Setup."

D= Disconnect

It closes the image channel that has screen selection cursor. Steps are as follows:

1) Select the image you want to close among the images being displayed.

2) Press "Disconnect" icon. The following message appears.

3) Click "Yes" to close the image of the channel that has screen selection cursor. Then

the images behind the blank window will be pushed upward one frame at a time.

4) In addition to the channel selected, the channel images that cannot communicate with

Netcam will also be closed.

5) Click "No" to cancel closing the image of the channel that has screen selection cursor.

Subtitle

Show/Hide

It turns the window in which the image information such as time or server name that is displayed on the screen window as text On/Off.

1) If you press the "Subtitle Show/Hide" icon, Netcam information will be displayed at the bottom of each screen as below.

2) If you want to hide the subtitle display, click the "Subtitle Show/Hide" icon one more time.

Record

1) Select the image you want to record among the images being displayed from the screen window.

2) Pressing the "REC" icon will start recording while "REF-F" is displayed on the OSD window.

3) Likewise, to record another image, select that image and then press "REC" icon. The recording will start.

- When using the default folder as the recording folder, the path is as follows:

{install drive}:\Program Files\Network Camera MultiViewer\Video Files

- Recording time continues by creating a 10-minute file per IP after recording is started.

- Recording stops when the hard disk capacity is below 5 GB.

4) To stop recording, select the channel you want to stop recording, and press "REC" icon one more time.

“ Recording stops automatically when the hard disk capacity is below 5 GB. Check the hard disk capacity before recording if you want to record continuously.

When Alarm occurs, that window will flash while recording is not happening.

54

Video Netcam | SNC-L200

Print

Prints the selected Netcam video.

The Video at the time "Print" is clicked will be printed.

Refer to 6.6 Print.

Capture

Use it to save a still video from live videos to a JPEG file.

To capture:

1) Select the video you want to capture from the screen window where videos are

displayed.

2) Click "Capture" icon. The path and numbers of pictures saved will be the folder and frame number settings for Image Capture in the Viewer Setup.

Motion

Sets up the motion detection mode of the Netcam selected.

Refer to 6.7 Motion.

Flash

Enables the Flash On/Off function in the currently selected channel.

When Flash On is selected, it flashes for 5 seconds then is off for 30 seconds.

During this Flash Off mode Flash On is disabled.

PIR

Enables the PIR Sensor On/Off function in the currently selected channel.

It flashes for 5 seconds automatically when there is a movement on the PIR

sensor of the relevant camera, and recording takes place for 5 seconds with

'REC-A' showing in red.

6.5 Setup

6.5.1 Registration

Connects the Netcam installed in the LAN or WAN network to the MultiViewer.

Click Setup

icon. The following window appears.

55

Video Netcam | SNC-L200

Setup @ Registration @ Viewer Setup List If Address Target Name User Name End Start Up Introduction Refreshed Edit Sub

1. Registration Registration

Use this tab to register Netcam.

1. New

Use to register a new Netcam.

1) Click New. The following screen appears.

2) Enter the IP Address, domain Name, TCP

Port No., User Name, and Password for the Netcam you want to connect.

3) Click OK.

4) Netcam is registered in the list of Registration window.

**Registration cannot be complete if the connection is failed or the network is disconnect.

56

Video Netcam | SNC-L200

1. Delete

Use to delete a registered Netcam.

1) Click on the Netcam to be deleted from the list using your mouse.

2) Click Delete. The following message appears.

3) Click "Yes" to delete the selected Netcam. Click "No" to not delete the selected Netcam.

4.

Use to modify the selected Netcam.

1) Click on the Netcam to be modified from the list using your mouse.

2) Click Modify. The following window appears.

3) Modify the registered information (IP Addr, HTTP Port, StartUp, User Name, and Password).

4) Click OK when modifying is complete. Click Close will not modify the registered information.

5) Verify if the Netcam is modified in the list of the Registration window.

* Modification cannot be complete if the connection is failed or the network is disconnect.

5.

Click "Close" button to exit Viewer Setup Mode.

1. Viewer Setup

Use this tab to run Viewer Setup.

** If you change Netcam Name using the SNC Installer while the video is connected, the Target Name in Viewer Setup will not change. The Target Name will change when you connect the video by running Netcam MultiViewer again.

57

Video Netcam | SNC-L200

6.5.2 Viewer Setup

Setup Registration Viewer Setup Image Recording Meeting Location:WAC storeCode + Time + Connection (F/S/A) Location C:\Program Files\Network Camera MultiViewer Browser... Schedule 168.215.98.188 [Network Camera] Browse... Image Capturing Frame Rate Frame/On Click(0-2) Sequence Time Sec (0-30) Single Logo Image File C:\Program Files\Network Camera MultiViewer\Software Store OK Cancel

1. Image Recording

- Location (Video Recording Folder): Designates the path to save the recorded video file

Default : {install drive}:\Program Files\Network Camera MultiViewer

- Schedule

Condition Schedule Select All Sun Mon Tue Wed Thu Fri Sat Use Time Range 14:30 ~ 14:30 OK Cancel

Sets Day and Time to saved the video of the selected channel.

When you set the Day only, videos will be saved 24 hours for the day. When you set the Time only, videos will be saved for the designated time everyday.

In addition, if you set both Time and Day, videos will be saved at the designated time on the day only.

58

Video Netcam | SNC-L200

2. Image Capturing

- Frame Rate: It designates numbers of videos that are saved when you run the Capture function once. You may set to 1\~3.

3. Sequence Time

- Use this to set the time a video switches. You may set to 5–30 seconds.

- If Single is checked, it switches to one server in sequence when you run the Sequence function.

4. Logo Image File

- It designates the folder path where the Logo file of File Folder Viewer is located.

Default: {install drive}: Program Files\Network Camera MultiViewer\Samsung_Logo.bmp

5. Cancel

Use this when not to apply the changed settings.

6. Close

Use this to apply the changed settings and exit Viewer Setup Mode.

6.6 Print

Use this when you want to print a still video from live videos.

To run the Print function, you must install and set the Printer in Print Setup that is at the top or Print.

1) Select the video you want to print from the screen window where videos are displayed.

2) Press "Print" icon ( ), The following screen appears.

文件 保存 Help Save Help SAMSUNG 2017.03.20 0:20:20 FID: 100% (RGB) POST: 100% (RGB) OK OK

59

Video Netcam | SNC-L200

3) Click "Memo" to enter the description to be recorded in the print and click OK. The description will be recorded and printed in the Memo field at the bottom of the print. You may enter up to 63 characters in a row.

4) Click "Setup" to select the printer.

Print Name: Samsung ML-1750 Series Status: Ready Type: Samsung ML-1750 Series Where: UPT1 Comment: Samsung ML-1750 Series Print Longs • All • Number of grades: 1 • Subtitle • OK Cancel

5) Press "Print" icon ( ). Printer starts printing while the transmission complete message appears. "Transmission failed" message appears when the printer is not set. You need to set the printer

6.7 Motion

It is a function to Alarm Recording when a motion is detected on Netcam videos.

Enable Motion Detection Sensitivity Pretest OK Cancel

1. Enable Motion Detection

Click it to turn the Motion Detection function on. Click it to turn the Motion Detection function off.

1. Sensitivity

Use it to set the sensitivity of the Motion. Set the sensitivity in numbers. Enter numbers between 1\~10. (10: Most sensitive)

1. Motion Area

The area marked with thick green on the screen is where Motion Detection occurs. It is divided into 16, and you may click the area you want to set repeatedly to run the Setup/Remove function.

1. Area that does no Motion

It is an area that does not Motion Detection.

1. Pretest

Sets the sensitivity temporarily.

1. OK

Closes the Motion Detection function after applying the settings.

1. Cancel

Closes the Motion Detection function without applying the settings.

To set the Motion Detection function:

1) Select the video you want to set and change for Motion Detection from the screen window where videos are displayed.

2) Click

"Motion" icon. The following window appears.

Enable Motion Detection Sensitivity Pretest OK Cancel

3) Select the area for motion detection by clicking the screen.
4) Change the Sensitivity number properly to select the optimum number. (10: Most sensitive)
5) Click "Preset" button to set the sensitivity temporarily.
6) When a motion is detected, the frame will flash in red.
7) Repeat steps 3)-6) to find the proper setting for the video.
8) Check "Enable Motion Detection."
9) Click OK when setup is complete.
10) Click Cancel if you do not want to apply the settings.

62

Video Netcam SNC-L200

The procedure for Motion Detection function is as follows:

1) A motion occurs in the video where the Motion Detection function setup is complete.
2) Window cursor flashes in red.
3) "REC-A" is displayed in red at the right bottom of the screen, and the recording
starts.
- Record is recorded in the same folder (Alarm) as the Pre/Post Alarm Record.
4) The motion detected is recorded in a Log file. The following information is recorded in the Log file.

• Time, Day, Month, Year of the motion detected
• Target name
• Netcam's MAC Address on which the motion is detected
• Netcam's IP on which the motion is detected
• File name of the Pre/Post Alarm Recording. (If you click the file, the video will be played back immediately and you can verify it.)
  * Refer to "6.8.7 Log File" for more details.

6.8 Player (Playback)

Use it to Playback, Search, Capture, or Print the recorded videos.

You may verify Netcam status, such as Disconnect, Reconnect, Alarm, Motion, etc.

* You must press Stop or Pause button to go to Viewer during playback or search.

Schwin Camera 16/SEP/2005 16:46:40 SAMSUNG DIGITECTS

63

Video Netcam | SNC-L200

6.8.1. File Open

Opens the video that will be played back. It opens and plays back the recorded files in the preset file path. It can also open several files (maximum 100 files) to play them back in sequence.

6.8.2. Screen Size Switch

Adjusts the video that is being played back to various sizes. However, the resolution of originally recorded video will not increase.

For example, a file recorded with 160X120, 320X480 resolution will not change to 640X480 when it is changed to 640X480. Only the size will change.

• 160*120 Plays back the recorded video in 160x120 regardless of the original video size.
• 320^240 Plays back the recorded video in 320x240 regardless of the original video size.
• 640*480 Plays back the recorded video in 640x480 regardless of the original video size.
• Window Full Plays back the recorded video in full size of the Player window regardless of the original video size.
  Full Screen Plays back the recorded video in the full screen without the Viewer frame regardless of the original video size.

6.8.3. Various Playback and Search

• 1x speed ▶ playback, reverse direction ▶ playback
• Stop and Pause
• 3x speed Fast Forward ▶ and Rewind ◀ for search
• Fine search with 1 screen forward ▶ and rewind ◀ playback
• Search for several recorded files in sequence, search for several files simultaneously by moving to before /after file starting pint. Files for the simultaneous search cannot exceed 100.

6.8.4. Snap Shot

Use it to save a still video from searched videos to a JPEG file. Steps to do Snapshot are as follows:
1) Select the video you want to capture from the screen window where videos are displayed.
2) Click "Snapshot" icon. The path and numbers of pictures saved will be the folder and frame number settings for Image Capture in the Viewer Setup.

64

Video Netcam | SNC-L200

6.8.5. Print

Use this when you want to print a still video from live videos.

To run the Print function, you must install and set the Printer in Print Setup that is at the top or Print.

1) Select the video you want to print from the screen window where videos are displayed.
2) Press "Print" icon. The following screen appears.

Print Add Setup Remove Wednesday, July 11, 2005 02:00:31 Rd FILE: 304517.8963405_2.5.0 POST: 199-00-00 01:54:31:00 V256

3) If you want to insert a memo on the paper, click "Memo" button at the top of Print screen. The following Memo screen appears. Enter the description you want to record. You may enter up to 63 characters in a row.

Mnmm MEMO: OK Cancel

4) Click OK when Memo key-in is complete. The description will be recorded and printed in the Memo field at the bottom of the print.

65

Video Netcam | SNC-L200

5) Click "Setup" button to set the printer.

Print Name: Samsung ML-1750 Series Status: Ready Type: Samsung ML-1750 Series Where: LPT1 Comment: Samsung ML-1750 Series Print size: P 2.8 □ Number of copies: 1 □ Color: OK Cancel

6) Click on the "Print" button on the top side of the print screen. The transfer complete message appears and then print begins.

"Transmission failed" message appears when the printer is not set. You need to set the printer

6.8.6. Status Display

Displays the information of the video that is currently being played back or searched.
- Bar: Displays current playback location from the entire length of the file that is being played back.
- Displays the total recording time and the time of current playback of the recorded file. - Displays Date/Time/Save Status in the file name.

Total File Size 08:06/00:15 20050715_09h53m05a_A4p Current Position Time Date/Time

6.8.7.

Log

File

Records the Netcam status (Disconnect, Recommend, Alarm and Motion). Alarm and Motion will be accompanied with the recordings, double clicking the recorded video file name will activate the player and you can check the video.

66

Video Netcam | SNC-L200

To run the Log file:

1) Click "Log File" icon. The following window appears.

Time Target Name If Address No. Event M File Folt

2) Click "File Open" icon. The following window appears.

Open Look in: Event Logs 20050713.log 20050714.log 20050715.log File name: 20050715.log Files of type: Log Files (*.log) Open Cancel

3) Click the file you want and click "Open" icon. The Log file content will be displayed.

67

Video Netcam | SNC-L200

Netcam MultiViewer

Time Target: IP Address MAC Address Event Mode 2005/01 5:09:03:20 Netw... 108 218 40 150 00-30-04-01-06 Reconnected 2005/01 5:09:03:00 Netw... 108 218 40 150 00-30-04-01-06 Alarm 2005/01 5:16:15:20 Netw... 168 218 40 150 00-30-04-01-06 Alarm 2005/01 5:16:15:30 Netw... 168 218 40 150 00-30-04-01-06 Alarm 2005/01 5:26:15:40 Netw... 168 218 40 150 00-30-04-01-06 Alarm 2005/01 5:26:15:50 Netw... 168 218 40 150 00-30-04-01-06 Alarm 2005/01 5:26:15:60 Netw... 168 218 40 150 00-30-04-01-06 Alarm 2005/01 5:26:15:70 Netw... 168 218 40 150 00-30-04-01-06 Alarm 2005/01 5:26:15:80 Netw... 168 218 40 150 00-30-04-01-06 Alarm 2005/01 5:26:15:90 Netw... 168 218 40 150 00-30-04-01-06 Alarm 2005/01 5:26:15:10 Netw... 168 218 40 150 00-30-04-01-06 Reconnected 2005/01 5:26:15:17 IIN 168 218 41 192 3D-3D-3D-3D- Recorlected 2005/01 5:26:15:27 IIN 168 218 41 191 3D-3D-3D-3D- Recorlected 2005/01 5:26:15:37 IIN 168 218 41 191 3D-3D-3D-3D- Recorlected 2005/01 5:26:15:47 IIN 168 218 41 192 3D-3D-3D-3D- Recorlected 2005/01 5:26:15:57 IIN 168 218 41 193 3D-3D-3D-3D- Recorlected 2005/01 5:26:15:67 IIN 168 218 41 194 3D-3D-3D-3D- Recorlected 2005/01 5:26:15:77 IIN 168 218 41 195 3D-3D-3D-3D- Recorlected 2005/01 5:26:15:87 IIN 168 218 41 196 3D-3D-3D-3D- Recorlected 2005/01 5:26:15:97 IIN 168 218 41 197 3D-3D-3D-3D- Recorlected 2005/01 5:26:15:10 IIN 168 218 41 198 3D-3D-3D-3D- Recorlected

4) Event date, time, target name, IP address or domain name, event category, recorded files and etc. are displayed. Double clicking the recorded video file will activate the player and you can search the video.

5) To return to Log File Search Mode after the video search is complete, click "Log File" icon again. Then you will return to the window shown in item 3).

6) Click "Close" button to exit.