SAM9M10-G45-EK - Development board Microchip - Free user manual and instructions

USER MANUAL SAM9M10-G45-EK Microchip

1.1 Scope 1-1
1.2 Applicable Documents 1-2

Section 2

Kit Contents 2-1

2.1 Deliverables 2-1
2.2 Evaluation Board Specifications.... 2-2
2.3 Electrostatic Warning 2-2

Section 3

Power up....3-1

3.1 Power Up the Board.... 3-1
3.2 Battery 3-1
3.3 DevStart 3-1
3.4 Recovery Procedure 3-2
3.5 Sample Code and Technical Support 3-2

Section 4

Board Description 4-1

4.1 Equipment on the Board 4-1

4.1.1 Interfaces 4-1
4.1.2 Board Interface Connection 4-2
4.1.3 Push Button Switches.... 4-2
4.1.4 Display LCD and LEDs 4-3

4.2 Hardware Layout and Configuration 4-3

4.2.1 Processor.... 4-3
4.2.2 Clock Circuitry 4-4
4.2.3 Reset Circuitry 4-4
4.2.4 Memory 4-4
4.2.5 Power Supplies.... 4-7
4.2.6 Debug Interface 4-10
4.2.7 Audio Stereo Interface 4-15
4.2.8 TV-Out Extension 4-17
4.2.9 Software Controlled LEDs 4-18
4.2.10 Serial Peripheral Interface Controller (SPI) 4-19
4.2.11 Two Wire Interface (TWI) 4-19
4.2.12 SD/MMC Interface 4-19
4.2.13 TFT LCD with Touch Panel 4-20
4.2.14 Push Buttons 4-22

4.2.15 Expansion Slot.... 4-22

Section 5

Configuration 5-1

5.1 JTAG/ICE Configuration.... 5-1
5.2 ETHERNET Configuration 5-1
5.3 Jumpers Configuration 5-2
5.4 Miscellaneous Configuration Items 5-3
5.5 PIO Configuration.... 5-3

5.5.1 Peripheral Signals Multiplexing on I/O Lines 5-3
5.5.2 Multiplexing on PIO Controller A (PIOA).... 5-3
5.5.3 Multiplexing on PIO Controller B (PIOB).... 5-5
5.5.4 Multiplexing on PIO Controller C (PIOC) 5-6
5.5.5 Multiplexing on PIO Controller D (PIOD) 5-7
5.5.6 Multiplexing on PIO Controller E (PIOE).... 5-8

Section 6

Connectors 6-1

6.1 Power Supply 6-1
6.2 RS232 Connector with RTS/CTS Handshake Support 6-1
6.3 DBGU 6-2
6.4 Ethernet....6-3
6.5 USB Host 6-3
6.6 USB Host/Device 6-4
6.7 JTAG Debugging Connector 6-4
6.8 SD/MMC-MCI0....6-6
6.9 SD/MMC-MCI1 6-7
6.10 AC97 6-8
6.11 Image Sensor - ISI 6-9
6.12 Video....6-10
6.13 Display Devices.... 6-10

6.13.1 TFT LCD 6-10

6.14 LCD Extension 6-11

Section 7

Schematics 7-1

7.1 Schematics.... 7-1

Section 8

Revision History......8-1

8.1 Revision History 8-1

1.1 Scope

This User Guide introduces the AT91SAM9M10(G45) Evaluation Kit and describes its development and debugging capabilities.

Figure 1-1. Board Photo

Green printed circuit board with various electronic components and a central display (no readable text or symbols)

The Atmel® SAM9M10-G45-EK is a fully-featured evaluation platform for the Atmel AT91SAM9M10 or AT91SAM9G45 microcontroller. The kit is equipped with an AT91SAM9M10 chip, which is a superset of the AT91SAM9G45, and therefore allows evaluating that reference as well. The evaluation kit allows users to extensively evaluate, prototype and create application-specific designs.

The SAM9M10-G45-EK includes many hardware peripherals such as:

■ Two high speed USB hosts and one high speed device port
■ An Ethernet 10/100 interface
■ Two high speed multimedia card interfaces

Introduction

■ An LCD TFT display (480*272 RGB) with resistive touch panel
■ A composite video output
■ A camera interface
■ Several communication peripherals such as:
– Universal Synchronous/Asynchronous Receiver Transmitter (USART)
- Two-Wire Interface (TWI)

The external memory block is made of 3 memory types:

DDR2-SDRAM
■ NAND Flash
■ NOR Flash (not populated by default)

1.2 Applicable Documents

Table 1-1. Applicable Documents

Reference Title Comments
Atmel Literature n° 6438 SAM9G45	Preliminary	This document describes the SAM9G45, which is part of the Atmel's Smart ARM® Microcontrollers.It is available fromhttp://www.atmel.com/dyn/resources/prod_documents/doc6438.pdf
Atmel Literature n° 6355 SAM9M10	Preliminary	This document describes the SAM9M10, which is part of the Atmel's Smart ARM® Microcontrollershttp://www.atmel.com/dyn/resources/prod_documents/doc6355.pdf

2.1 Deliverables

The Atmel SAM9M10-G45-EK toolkit includes:

■ Board
- The SAM9M10-G45-EK board
■ Power supply
- Universal input AC/DC power supply with US, Europe and UK plug adapters - One 3V Lithium Battery type CR1225
■ Cables
- One micro A/B-type USB cable
- One serial RS232 cable
- One RJ45 crossed cable
■ A Welcome Letter

Figure 2-1. Unpacked SAM9M10-G45-EK

Open cardboard box containing a green printed circuit board, coiled with white cables and connectors, no visible text or symbols.

Unpack and inspect this kit carefully. Contact your local Atmel distributor, should you have issues concerning the contents of the kit.

2.2 Evaluation Board Specifications

Table 2-1. SAM9M10-G45-EK Specifications

Characteristics Specifications
Clock speed 400 MHz PCK, 133 MHz MCK
Ports Ethernet, USB, RS232, DBGU, JTAG
Board supply voltage 5 VDC from connector
Temperature- operating- storage	-10^ to +50^ C -40^ to +85^ C
Relative humidity 0 to 90% (non condensing)
Dimensions 180 mm x 140 mm
RoHS status Compliant

2.3 Electrostatic Warning

The SAM9M10-G45-EK evaluation board is shipped in a protective anti-static package. The board must not be subjected to high electrostatic potentials. We strongly recommend using a grounding strap or similar ESD protective device when handling the board in hostile ESD environments (offices with synthetic carpet, for example...). Avoid touching the component pins or any other metallic element on the board.

3.1 Power Up the Board

Unpack the board taking care to avoid electrostatic discharge. Unpack the power supply, select the right power plug adapter corresponding to that of your country, and insert it in the power supply.

Connect the power supply DC connector to the board and plug the power supply to an AC power plug.

The board LCD should light up and display a welcome page. Then, click or touch icons displayed on the screen and enjoy the demo.

3.2 Battery

The SAM9M10-G45-EK ships with a 3V coin battery.

This battery is not required for the board to start up.

The coin battery is provided for user convenience in case the user would like to exercise the date and time backup function of the SAM9M10 series devices when the board is switched off.

3.3 DevStart

The on-board NAND Flash contains a "SAM9M10-G45-EK DevStart".

It is stored in the "SAM9M10-G45-EK DevStart" folder on the USB Flash disk available when the SAM9M10-G45-EK is connected to a host computer.

Click the file "welcome.html" in this folder to launch SAM9M10-G45-EK DevStart.

SAM9M10-G45-EK DevStart guides you through installation processes of IARTM EWARM, Keil MDK and GNU toolkits. Then, it gives you step-by-step instructions on how to rebuild a single example project and how to program it into the SAM9M10-G45-EK. Optionally, if you have a SAM-ICE™, instructions are also given about how to debug the code.

We recommend that you backup the “SAM9M10-G45-EK DevStart” folder on your computer before launching it.

3.4 Recovery Procedure

The DevStart ends by giving step-by-step instructions on how to recover the SAM9M10-G45-EK to the state as it was when shipped by Atmel.

Follow the instructions if you deleted the contents of the NAND Flash and want to recover from this situation.

3.5 Sample Code and Technical Support

After boot up, you can run some sample code or your own application on the development kit. You can download sample code and get Technical support from http://www.atmel.com/dyn/products/tech_support.asp?Faq=y&family_id=689%20.

4.1 Equipment on the Board

Figure 4-1. Board Architecture

graph TD
    A["Main Memory"] --> B["External Memory"]
    B --> C["External Cards"]
    C --> D["Multimedia Cards Interface"]
    D --> E["LCD TFT 480*272"]
    E --> F["Touch Screen"]
    F --> G["Composite video"]
    G --> H["AC97"]
    H --> I["PWM"]
    I --> J["PIO"]
    J --> K["USB"]
    K --> L["DEBUG"]
    L --> M["JTAG/ICE#GU"]

    subgraph AT91SAM9M10
        N["System Controller"] --> O["Image Sensor Interface"]
        O --> P["TWI"]
        P --> Q["ETHERNET 10/100 MAC"]
        Q --> R["USART"]
        R --> S["USB"]
        S --> T["DEBUG"]
    end

    subgraph Media Cards
        U["DDR2 SDRAM"] --> V["External Memory"]
        W["NAND FLASH"] --> V
        X["DDR2 SDRAM"] --> Y["External Memory"]
        Z["NCS1"] --> V
        AA["NCS3"] --> V
        AB["NCS0"] --> V
        AC["Data Flash"] --> AD["MCI1"]
        AE["8 bits interface SD/MMC"] --> AF["MCI1"]
        AG["SPIO"] --> AH["MCIO"]
        AI["4 bits interface SD/MMC"] --> AJ["MCIO"]
        AK["CD"] --> AL["MultiMedia Cards Interface"]
    end

    subgraph Video
        AM["Micro"] & AN["Line In"] & AO["Line Out"] & AP["Audio"] & AQ["User I/O"] & AR["Joystick & P.B."]
    end

    subgraph Audio
        AS["Codec"] --> AT["AC97"]
        AU["Led"] --> AV["PWM"]
    end

VCC 5V

ISI

Ethernet RMII/MII

RS232

USB HubHigh / Full

USBHub / Device

DBGU

JTAG/ICE

PIO

4.1.1 Interfaces

The board is equipped with an AT91SAM9M10-CU embedded microprocessor (324-ball TFBGA package) together with the following interfaces or peripherals:

■ DDR2/LPDDR memory interface is connected to 128 MB DDR2-SDRAM memory
■ External Bus Interface (EBI) is connected to three kinds of memory devices (DDR2-SDRAM, NAND Flash and NOR Flash (not populated))

Board Description

■ One TWI serial memory
■ One USB Host/Device multiplexed port interface
■ One USB Host port interface
■ One RS232 serial communication port
■ One DBGU serial communication port
■ One JTAG/ICE debug interface
■ One Ethernet 100-base TX with three status LEDs
■ One AC97 Audio CODEC with headphone line out, line in and mono/stereo microphone inputs
■ One TV interface (composite video output)
■ One 4.3" TFT LCD Module with touch screen and back light
■ One ISI connector (camera interface)
■ One power red LED and two general-purpose green LEDs
■ Two user input push buttons
■ One joystick with 4-direction control and selector
■ One wakeup input push button
■ One reset input push button
■ One SD/SDIO/MMC plus card slot (4/8 bit interface)
■ One SD/SDIO/MMC card slot (4-bit interface)
■ One Lithium Coin Cell Battery Retainer for 12 mm cell size (memory backup usage)

4.1.2 Board Interface Connection

■ Ethernet using RJ45 connector (J15)
■ USB Host, support USB host using a type A connector (J12)
■ USB Host/Device, support USB host/device using a type micro AB connector (J14)
■ UART1 (RX, TX, RTS, CTS) connected to a 9-way male D-type RS232 connector (J11)
■ DBGU (RX and TX only) connected to a 9-way male D-type RS232 connector (J10)
■ JTAG, 20 pin IDC connector (J13)
■ SD/MMCplus connector (J5)
■ SD/MMC connector (J6)
■ Headphone (J7), line-in (J8) and microphone headset (J9)
■ Speaker output (JP15)
■ Image sensor connector (J17)
■ TFT LCD display, with TouchScreen and backligth (J24)
■ Test points; various test points are located throughout the board
■ Main power supply (J2)

4.1.3 Push Button Switches

■ Reset, board reset (BP1)
■ Wake up, push button to bring processor out of low power mode (BP2)
■ Right and left click, user push button switches (BP4 and BP5)
■ Joystick (BP3)

4.1.4 Display LCD and LEDs

■ Display, 480xRGBx272 pixels LCD module display connected to the PIO port E (LCD1)
■ One surface-mounted power red LED, user interface (D3)
■ Two surface-mounted green LEDs, user interface (D1 and D2)
■ Three surface-mounted LEDs indicate Ethernet status (D4, D5, D6)

Figure 4-2. Board Layout Commented

DBGU RS232 JTAG ETHERNET HOST USB HOST DEVICE USB POWER LINE INPUT MICROPHONE INPUT HEADPHONES HEADER VIDEO OUTPUT USER JOYSTICK SD/MMC 0 SLOT LCD DISPLAY AREA LCD EXTENSION CONNECTORS ISI/CAMERA CONNECTOR WAKE-UP BUTTON RESET BUTTON BACKUP BATTERY «RIGHT» USER BUTTON «LEFT» USER BUTTON SD/MMC 1 SLOT

The major components of the SAM9M10-G45-EK board are shown in Figure 4-1.

4.2 Hardware Layout and Configuration

4.2.1 Processor

The board features the Atmel SAM9M10-CU 324-ball TFBGA package. This chip runs at a nominal frequency of 400 MHz for the core and 133 MHz for the system bus.

For more information, refer to the latest SAM9M10 datasheet available from http://www.atmel.com/

Board Description

4.2.2 Clock Circuitry

The SAM9M10-G45-EK includes six clock sources:

■ Two are alternatives for the SAM9M10 main clock,
■ One crystal and one crystal oscillator are used for the Ethernet MII/RMII chip,
■ One crystal is used for the AC97 codec chip,
■ One crystal or one crystal oscillator is used for the TV encoder.

Table 4-1. Main Components Associated with the Clock Systems

Quantity Description Component assignment
1 Crystal	for Internal Clock, 12 MHz Y1
1 Crystal	for RTC Clock, 32.768 kHz Y2
1 Oscillator for Ethernet Clock RMII, 50 MHz Y4
1 Crystal	for Ethernet Clock MII, 25 MHz (not populated) Y5
1 Crystal	for AC97 Codec Clock, 24.576 MHz	Y3
1	Crystal for TV Encoder Clock, 13 MHz, or Oscillator for TV Encoder, 13 MHz (not populated)	Y7Y6

4.2.3 Reset Circuitry

The reset sources are:

■ Power on reset
■ Push button reset
■ JTAG reset from an in-circuit emulator interface.

4.2.4 Memory

4.2.4.1 External Memories

The SAM9M10 features a DDR2/LPDDR memory interface and an External Bus Interface (EBI) to permit interfacing to a wide range of external memories and to almost any kind of parallel peripheral.

The SAM9M10-G45-EK board is equipped with DDR2/LPDDR devices featuring 128 MB of DDR2-SDRAM memory (16Meg*8*4).

The External Bus Interface (EBI) is connected to three kinds of memory devices:

■ One Parallel Flash (not populated by default)
■ Two DDR2-SDRAM
■ One NAND Flash (2Gb, 8 bit bus)

The chip selects NCS0, NCS1 and NCS3 are used for NOR Flash, DDR2-SDRAM and NAND Flash memories, respectively. Furthermore, a dedicated jumper can disconnect each of the two NCS0 and NCS3 signals, making them available for other functions.

Figure 4-3. EBI0 - DDR2

Board Description

DDR2 DDR_C00_159 DDR_A0_158 DDR_A0_157 DDR_A0_156 DDR_A0_155 DDR_A0_154 DDR_A0_153 DDR_A0_152 DDR_A0_151 DDR_A0_150 DDR_A0_149 DDR_A0_148 DDR_A0_147 DDR_A0_146 DDR_A0_145 DDR_A0_144 DDR_A0_143 DDR_A0_142 DDR_A0_141 DDR_A0_140 DDR_A0_139 DDR_A0_138 DDR_A0_137 DDR_A0_136 DDR_A0_135 DDR_A0_134 DDR_A0_133 DDR_A0_132 DDR_A0_131 DDR_A0_130 DDR_A0_129 DDR_A0_128 DDR_A0_127 DDR_A0_126 DDR_A0_125 DDR_A0_124 DDR_A0_123 DDR_A0_122 DDR_A0_121 DDR_A0_120 DDR_A0_119 DDR_A0_118 DDR_A0_117 DDR_A0_116 DDR_A0_115 DDR_A0_114 DDR_A0_113 DDR_A0_112 DDR_A0_111 DDR_A0_110 DDR_A0_109 DDR_A0_108 DDR_A0_107 DDR_A0_106 DDR_A0_105 DDR_A0_104 DDR_A0_103 DDR_A0_102 DDR_A0_101 DDR_A0_100 DDR_A0_99 DDR_A0_98 DDR_A0_97 DDR_A0_96 DDR_A0_95 DDR_A0_94 DDR_A0_93 DDR_A0_92 DDR_A0_91 DDR_A0_90 DDR_A0_89 DDR_A0_88 DDR_A0_87 DDR_A0_86 DDR_A0_85 DDR_A0_84 DDR_A0_83 DDR_A0_82 DDR_A0_81 DDR_A0_80 DDR_A0_79 DDR_A0_78 DDR_A0_77 DDR_A0_76 DDR_A0_75 DDR_A0_74 DDR_A0_73 DDR_A0_72 DDR_A0_71 DDR_A0_70 DDR_A0_69 DDR_A0_68 DDR_A0_67 DDR_A0_66 DDR_A0_65 DDR_A0_64 DDR_A0_63 DDR_A0_62 DDR_A0_61 DDR_A0_60 DDR_A0_59 DDR_A0_58 DDR_A0_57 DDR_A0_56 DDR_A0_55 DDR_A0_54 DDR_A0_53 DDR_A0_52 DDR_A0_51 DDR_A0_50 DDR_A0_49 DDR_A0_48 DDR_A0_47 DDR_A0_46 DDR_A0_45 DDR_A0_44 DDR_A0_43 DDR_A0_42 DDR_A0_41 DDR_A0_40 DDR_A0_39 DDR_A0_38 DDR_A0_37 DDR_A0_36 DDR_A0_35 DDR_A0_34 DDR_A0_33 DDR_A0_32 DDR_A0_31 DDR_A0_30 DDR_A0_29 DDR_A0_28 DDR_A0_27 DDR_A0_26 DDR_A0_25 DDR_A0_24 DDR_A0_23 DDR_A0_22 DDR_A0_21 DDR_A0_20 DDR_A0_19 DDR_A0_18 DDR_A0_17 DDR_A0_16 DDR_A0_15 DDR_A0_14 DDR_A0_13 DDR_A0_12 DDR_A0_11 DDR_A0_10 DDR_A0_9 DDR_A0_8 DDR_A0_7 DDR_A0_6 DDR_A0_5 DDR_A0_4 DDR_A0_3 DDR_A0_2

Board Description

Figure 4-4. EBI1 - DDR2 + Flash

EBI FLASH-01.15 EBI FLASH_A1.20 EBI 08.58.15 EBI 08.48.15 MNS EBI-02 A3 H8 EBI-02A EBI-02 A3 H7 EBI-02A EBI-02 A3 H6 EBI-02A EBI-02 A3 H5 EBI-02A EBI-02 A3 H4 EBI-02A EBI-02 A3 H3 EBI-02A EBI-02 A3 H2 EBI-02A EBI-02 A3 H1 EBI-02A EBI-02 A3 H9 EBI-02A EBI-02 A3 H7 EBI-02A EBI-02 A3 H5 EBI-02A EBI-02 A3 H3 EBI-02A EBI-02 A3 H1 EBI-02A EBI-02 A3 H8 EBI-02A EBI-02 A3 H6 EBI-02A EBI-02 A3 H4 EBI-02A EBI-02 A3 H3 EBI-02A EBI-02 A3 H1 EBI-02A EBI-02 A3 H9 EBI-02A EBI-02 A3 H7 EBI-02A EBI-02 A3 H5 EBI-02A EBI-02 A3 H3 EBI-02A EBI-02 A3 H1 EBI-15A EBI-02 A3 H9 EBI-15A EBI-02 A3 H7 EBI-15A EBI-02 A3 H5 EBI-15A EBI-02 A3 H3 EBI-15A EBI-02 A3 H1 EBI-15A EBI-02 A3 H8 EBI-15A EBI-02 A3 H6 EBI-15A EBI-02 A3 H4 EBI-15A EBI-02 A3 H3 EBI-15A EBI-02 A3 H1 EBI-15A EBI-02 A3 H9 EBI-15A EBI-02 A3 H7 EBI-15A EBI-02 A3 H5 EBI-15A EBI-02 A3 H3 EBI-15A EBI-02 A3 H1 EBI-15A ESI UBE I4 GZ RAO RDOS/OW DQMS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDOS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDDS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDG/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGS/EN RDGRD/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDY/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDYS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/DVD/RDTS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/TVCS/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SvcS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvS/CvSC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SVC/SNC/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A/A-A/B/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C-C/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/VCC/Vcc/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/c/s/n/ EBI NAND_FSL-DIO.15N PC5 NANDLES MND P.C.BR NCLE CLE VCC HDH FHI NAND PS-R NCLE MDN P.C.BR NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCl NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCL NCLE KCI NCLO CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNC CCNCA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CA CANOLED DATA BUS WIP-A#F#F#F#F# INTORTANT NOTE SCAT SYSTEM HOODING: The bootbox allows booting from the block 6 or a MaxFlash connected on CS3. However, the bootbox does not feature RCC (Petro Checking and Correction) on Mandlash. Most of the HandFlash vendors do not guarantee anymore that block 6 is error free. Therefore we advise the bootstrap program to be located into another device supported by the bootbox (DataFlash, Serial Flash, SUCARD or s.p.fROW) and implement Mandlash access with SCC. EBI NAND_FSL-DIO.15N PC5 NANDLES MND P.C.BR NCLE CLE VCC HDH FHI NAND PS-R NCLE MDN P.C.BR NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCCL NCLE KCFLC CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNCK CNKCNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKCNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNKCN KNkRNKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKn KnknKRnTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTNTN TNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTTNNTINNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNNTNAITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITINITInIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIinIIInIIinIIinIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIInIIIns

4.2.5 Power Supplies

The SAM9M10 Board contains four regulated power supplies:

■ 3.3 VDC Supply
■ 1.8 VDC Supply
■ 1.0 VDC Core Supply
■ 1.0 VDC Core UTMI Supply, PLL

The outputs of these regulated power supplies ^1 are distributed as necessary to each part of the circuit board.

■ The 3.3 VDC Supply is generated by an adjustable LDO. It accepts VIN 5 VCC power and outputs a regulated +3.3 V to most other circuits on the board.
■ The 1.8 VDC Supply (VDDIOM0, VDDIOM1) is generated by an adjustable LDO. It is powered by VIN 5 VCC power and outputs a regulated +1.8V.
■ The 1.0 VDC Core Supply (VDDCORE) is generated by an adjustable LDO. It is powered by the output of the 3.3 VDC Supply.
■ The 1.0 VDC Core Supply (VDDUTMIC, VDDPLLUTMI and VDDPLLA) is generated by an adjustable LDO RT9186A series. It is powered by the output of the 3.3 VDC Supply.

Note: 1. Corresponding test points (TP1 to TP4, GND) are used with jumpers (JP1.1 to JP7) to permit probing of these voltages.

Board Description

Figure 4-5. Power Supply

3V3 F10 100k MNS RT3186A VIN VIN PGOOD EN OUT VOUT ADJ GND R14 12k C19 10n C21 10u R19 47k C22 1u R15 1R C2 100n C20 4.7u C29 100n L1 10uH R1 1R C1 100n L2 10uH R5 1R C8 100n JP1,JP1 JP2,JP2 JP3,JP3 JP4,JP4 JP5,JP5 JP6,JP6 JP7,JP7 JP8,JP8 JP9,JP9 JP10,JP10 JP11,JP11 JP12,JP12 JP13,JP13 JP14,JP14 JP15,JP15 JP16,JP16 JP17,JP17 JP18,JP18 JP19,JP19 JP20,JP20 JP21,JP21 JP22,JP22 JP23,JP23 JP24,JP24 JP25,JP25 JP26,JP26 JP27,JP27 JP28,JP28 JP29,JP29 JP30,JP30 J1-1J1-1 2 VDDUTMII VDDANA VDDOSC VDDIOP0 VDDIOP1 VDDIOP2 VDDISI J1-2J1-2 34 VDDUTMIC J1-4J1-4 7 8 VDDPLLUTMI L310μHz-3.5μHzH C15 2.2μ C18 100n L4 10uH VDDPLLA J1-3J1-3 5 6 VDDCORE JPS,JP5 3 VDDICM0 JP9,JP6 3 VDDICM1 J3J3 3V3 C30 100n VDDBU

Figure 4-6. Management Power Block

REGULATED 5V ONLY J2 DC POWER JACK C4 33u CR1 5V 5V 3V3 R3 100k MN2 RT9016A PGOOD GND EN ADJ VIN VDD NC C10 1u 8 7 6 5 C9 10u C11 1u C310n0010n R1 47xR1 47x 3V3 R7 15k C11 1u C12 10u 5V R9 100k PWR_EN Q1 SIT563EDH JP4 SIP2 1 3 C17 2 15p R16 10k R17 10k SHDN MN4 RT9016A PGOOD GND EN ADJ VIN VDD NC 8 7 6 5 5V R11 100k MN4 RT9016A PGOOD GND EN ADJ VIN VDD NC C24 1u C23 10u C26 1u C16 10k C16 10n R15 15kFU15 15x R18 12k C27 10u

3V3 R2 10Ck MINI RT9186A VIN VIN PGOOD EN VOUT VOUT ADU GND 1 2 3 4 5 6 7 8 F199 10Ck C13 1u σ1 R6 12k C5 10n R8 47k C6 10u C7 1u 1V

Board Description

4.2.6 Debug Interface

4.2.6.1 JTAG/ICE

Software debug is accessed by a standard 20-pin JTAG connection. This allows connection to a standard USB-to-JTAG in-circuit emulator.

Figure 4-7. JTAG Interface

ICE INTERFACE 3V33V3 J13 RR43 100k 3V3 DNP R91 OR NTRST TDI TMS TCK RTCK TDO NRST NTRST TDI TMS TCK RTCK TDO NRST HTST-110-01-SM-D R92 ORR92 OR R93 OR R94 OR DNP

This UART is connected to the DB-9 male socket through an RS-232 Transceiver (TXD and RXD only).

Figure 4-8. DBGU Com Port

SERIAL DEBUG PORT J10 1 6 2 7 3 8 4 9 5 11 10 3V3 MN15 C158100nC158100n C157100nC157100n C165100nC166100n C159 100n GND CL+ 1 3 4 C1- C2+ 5 C2-V- 14 7 13 12 98 ADM3202ARNZ R90 0RB90.0R 3V3 R87 100k R88 100k PB13 PB12

4.2.6.3 User Serial Com Port

The USART1 is used as a user serial communication port. This USART1 is buffered with an RS-232 Transceiver (TXD, RXD and handshake CTS/RTS control) and connected to the DB-9 male socket. Software must assign the appropriate PIO pins (PB5 = RXD1, PB4 = TXD1, PD16 = RTS1, PD17 = CTS1) to enable the UART1 function.

Figure 4-9. User Serial Com Port

RS232 COM PORT SV3 R89 100k R88 100k MN16 C160 100n C164 100n 3 4 5 6 7 8 9 10 11 12 13 14 15 16 3V3 C161 100n C162 100nC162 100n C166 100nC166 100n ADM32C2A-RNZ PD4 PD16 PB5 PD17 J1J11

Refer to the SAM9M10 datasheet for more information about the SAM9M10 USARTs.

4.2.6.4 USB Port

The SAM9M10-G45-EK features USB communication ports:

■ Two Host Ports: Full speed OHCI and High speed EHCI
■ One Device Port: High speed.

USB Host Port0 is directly connected to the first UTMI transceiver. The second Host Port (Port1) is multiplexed with the USB Device High speed and connected to the second UTMI port.

■ One USB high/full speed type standard A connector
■ One USB interface Host/Device Micro AB connector

Refer to the SAM9M10 datasheet for detailed programming information.

Board Description

Figure 4-10. USB Port

USB HOST INTERFACE J12 G3505-4NBT1S1W 1 2 3 HDMA C167 100n 4 5 6 USB-A L13 1 2 220ohm at 100MHz C168 33u L14 1 2 220ohm at 100MHz C170 33u 5V MN17 OUTA ENA IN FLGA GNG FLGB OUTB ENB AIC1526-0GS (ENA) PD1 (FLGA) PD2 (FLGB) PD4 (ENB) PD3 USB HOST/DEVICE INTERFACE R95 47kR95 47k (VBUS) PB19 C171 10p R96 68k R97 47k 3V3 J14 7 KBCS 1 DM 2 DE 3 TH 4 GND 5 G3515-09010101-00 (IDUSB) HDMB HDPB PD28 C172 100n

4.2.6.5 Ethernet 10/100 (EMAC) Port

The port is compatible with IEEE® Standard 802.3.

The SAM9M10-G45-EK is equipped with a Davicom DM9161AEP 10/100 Mbps Fast Ethernet Physical Layer TX/FX Single Chip Transceiver. It contains the entire physical layer functions of 100BASE-TX as defined by IEEE 802.3u, including the Physical Coding Sublayer (PCS), Physical Medium attachment (PMA), Twisted Pair Physical Medium Dependent Sublayer (TP-PMD), 10BASE-TX Encoder/Decoder (ENC/DEC), and Twisted Pair Media Access Unit (TPMAU).

The Ethernet interface integrates an RJ45 connector with an embedded transformer, and three status LEDs.

The Ethernet interface provides two selectable modes, MII or RMII (Reduced MII), for 100Base-TX or 10Base-TX. The MII and RMII interfaces are capable of both 10Mb/s and 100Mb/s data rates as described in the IEEE 802.3u standard. The signals used by MII and RMII interfaces are described in the table below.

Table 4-2. Pin Mapping for Normal MII and Reduced MII

Pin Name Normal	MII Mode Reduced MII Mode
	SAM9M10 DM9161 SAM9M10 DM9161
ETX0-ETX1 ETX[0:1] transmit data TXD [0:1] ETX[0:1] TXD [0:1]
ETX2-ETX3 ETX[2:3] transmit data TXD [2:3] NC NC
ETXEN ETXEN: transmit enable TXEN ETXEN: transmit enable TXEN
ETXER ETXER: transmit error TXER/TXD[4] NC NC
ETXCK/REFCK	ETXCK: transmit clock	TXCLK	REFCK: reference clock	REF_CLK
ERX0-ERX1	ERX[0:1]: receive data	RXD [0:1]	ERX[0:1]: receive data	RXD [0:1]
ERX2-ERX3	ERX[2:3]: receive data RXD [2:3]	NC NC
ERXER	ERXER: receive error	RXER/RXD[4]/RPTR/NODE	ERXER: receive error	RPTR/NODE
ERXDV	ERXDV: receive valid data	RXDV	ECRSDV: carrier sense / data valid	CRS DV
ERXCK	ERXCK: receive clock	RXCLK	NC NC
ECOL	ECOL: collision detect	COL	NC NC
ECRS	ECRS: carrier sense / data valid	CRS (PHYAD[2:4]	NC NC
EMDC	EMDC: management data clock	MDC	EMDC: management data clock	MDC
EMDIO	EMDIO: management data input / output	MDIO	EMDIO: management data input / output	MDIO
NRST	NRST: microcontroller reset	RESET# XT1(25 MHz)	NRST: microcontroller reset	RESET# XT1(REF_CLK 50MHz)

Figure 4-11. Ethernet Port

RJ45 ETHERNET CONNECTOR RJ45 ETHERNET CONNECTOR 3V3 C175 220 DNP C174 220 DNP C110.0V DNP M018 REF CLKXT2 TX03 TX02 TX01 TX00 TX EN TX_CLM-DCATE RXDSPHYAD2 RXDSPHYAD2 RXDSPHYAD1 RXDSPHYAD0 RXCLKY-0BTSE9 RX DVTESTMODER TX_EPI-X64 RX_EPI-X64-RPTR CO-PAMII CRS-PHYADS MX616-AFP AVODT AVODR AVODR AVODT AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODR AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODD AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODO AVODU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDDU DVDOU 10kΩ/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/MHz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Hz/Ch

For more information about the Ethernet controller device, refer to the Davicom DM9161 controller manufacturer's datasheet.

4.2.7 Audio Stereo Interface

The SAM9M10-G45-EK includes a WM9711L AC97 CODEC for digital sound input and output. This interface includes audio jacks for MIC input (J9), line audio input (J8), headphone line output (J7) and a 2-point speaker output connector (JP15).

It is compliant with AC97 Component Specification V2.2.

Figure 4-12. Audio Stereo Interface

HEADPHONE LINE-OUT 15 220km at 100kHz C126 - 100kV R70/AC37.14F C127 - 100kV R71 47k C128 47k C129 47k C130 47k A5ND_AC3F JPN DNP A5ND_AC3F P13/CPB/R3R P14/CPB/R3R P15/CPB/R3R P16/CPB/R3R P17/CPB/R3R C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 C56 C57 C58 C59 C60 C61 C62 C63 C64 C65 C66 C67 C68 C69 C70 C71 C72 C73 C74 C75 C76 C77 C78 C79 C80 C81 C82 C83 C84 C85 C86 C87 C88 C89 C90 C91 C92 C93 C94 C95 C96 C97 C98 C99 C100 A5ND_AC3F A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5ND_AC3F OUT A5N/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D/A/C/D A/C/D_AC3F 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uU 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uV 10uM/SEAKER OUTPUT

For more information about the AC97 codec device, refer to the Wolfson WM9711L controller manufacturer's datasheet.

4.2.8 TV-Out Extension

The Chronel™ CH7024 chip provides an interface between the SAM9M10 LCD Controller and a TV set by converting LCD signals to TV signals.

The CH7024 is a TV encoder device which encodes the video signals and generates synchronization signals for NTSC and PAL standards. Supported TV output formats are NTSC-M, NTSC-J, NTSC-433, PAL-B/D/G/A/I, PAL-M, PAL-N and PAL-60. The CH7024 provides video output support for CVBS or S-video.

Figure 4-13. TV-Out Extension Port

PE[0..30] PE30 (B7) PE28 (B6) PE28 (B5) PE27 (B4) PE26 (B3) PE25 (B2) PE24 (B1) PE23 (B0) PE22 (G7) PE21 (G6) PE20 (G5) PE19 (G4) PE18 (G3) PE17 (G2) PE16 (G1) PE15 (G0) PE14 (R7) PE13 (R6) PE12 (R5) PE11 (R4) PE10 (R3) PE9 (R2) PE8 (R1) PE7 (R0) PE6 (LCDDEN) PE5 (LCDDOTCK) PE4 (HSYNC) PE3 (VSYNC) PE2 (LCDCC) PE1 (LCDMOD) PE0 (LCDPWR) MN20 CH7024B D0 PE23 42 PE24 43 PE25 44 PE26 45 PE27 46 PE28 47 PE29 48 PE30 1 PE15 2 PE16 3 PE17 4 PE18 5 PE19 6 PE20 7 PE21 8 PE22 9 PE7 10 PE8 11 PE9 12 PE10 13 PE11 14 PE12 15 PE13 17 PE14 19 VDDIO DVDD 38 16 C196 100n C197 100n C198 10u 10V DGND 18 AVDD_PLL 32 C200 100n AGND_PLL 31 AVDD 33 C202 100n AGND 36 AVDD_DAC 25 C203 100n AGND_DAC 29 R1781.2k ISET 30 CVBS 28 Y SPD SPC RESET NC XUFIN XO P-OUT TP6 COMPOSITE Video Output RCA JACK J2C TV_VSYNC TV_HSYNC TV_XCLK 3V3 R179 4M79.4.7k PA20 ITW DO) ITW CKO) NRST Y6 DNP Y59 VSS OUT DNP R184 10k DNP 1 OE VSS OUT DNP R186 0 DNP C207 100n DNP R185 OR Y7 3 13MHz C208 10p C209 10p L17 2200R 3V3 L18 2200R 1V8 C199 10u 10V L20 2200R 3V3 C201 10u 10V Composite Video Output RCA JACK J2C

Board Description

4.2.9 Software Controlled LEDs

Three users LED are provided for general use. The LEDs are connected to PIO port lines, allowing their control through either GPIO or PWM control.

■ LEDs D1 to D3 are software controlled by PIO pins.
■ LEDs D4 to D6 indicate Ethernet traffic and link status. These are automatically managed by on-chip microcontroller hardware. See Section 7.1 "Schematics".

Table 4-3. Discrete LEDs

LED Description Comment
D1 Green	LED User software controlled
D2 Green	LED User software controlled
D3 Red	LED User software controlled
D4 Yellow	LED Indicates transmission or reception via Ethernet
D5 Green	LED Indicates speed 100
D6 Green	LED Is lit when a good link test has been detected

Figure 4-14. Software Controlled LEDs

4.2.10 Serial Peripheral Interface Controller (SPI)

The SAM9M10 provides two high-speed Serial Peripheral Interface (SPI) controllers. One port is used to interface with the on-board serial DataFlash ^® .

Figure 4-15. SPI

PB0 (SP10 MISO) PB1 (SP10 MOSI) PB2 (SP10 SPCK) PB3 (SP10 NPC50) NRST theat points DNP JP11 3V3 R67 47CK 8 1 2 3 4 5 6 7 8 9 10 3V3 MN13MN13 SO VCC SI SCK CND CS RESET WP C124 100n R68 OR DNP SERIAL DATAFLASH

4.2.11 Two Wire Interface (TWI)

The SAM9M10 has a full speed (400 kHz) master/slave I2C Serial Controller. The controller is fully compatible with the industry standard I2C and SMBus Interfaces. This port is used to interface with the onboard Serial EEPROM, ISI and TV encoder interface.

Figure 4-16. TWI

PA21 PA20 (TW CK0) (TW DO) 6 5 MN12MN12 SCL SDA A0 A1 A3 1 2 3 4 VCC C125 100nC125 100n GND WP 7 3V3 R66 10k JP13 SIP2 SERIAL EEPROM

4.2.12 SD/MMC Interface

The SAM9M10-G45-EK has two high-speed 8-bit multimedia interfaces MMC/MMCPlus v4.1. The first interface is used as an 8-bit interface (MCI1), connected to a CE-ATA connector footprint and an 8-bit SD/MMC card slot. The second interface is used as a 4-bit interface (MCI0), connected to a 4-bit SD/MMC card slot.

The users must provide their own compatible cards for use with these connectors.

Please note that the power is connected to VCC, which is 3.3 volts.

Board Description

Figure 4-17. SD/MMC0

PD29 PD11 PA[22..31] (MCI1_WP) (MCI1_CD) PA24 (MCI1_DA1) 1 8 PA23 (MCI1_DA0) 2 7 PA31 (MCI1_CK) 3 6 27R PA22 (MCI1_CDA) 1 RR41 5RR41 27R PA25 (MCI1_DA3) 2 7 PA25 (MCI1_DA2) 3 6 PA27 (MCI1_DA4) 1 8 PA28 (MCI1_DA5) 2 7 PA29 (MCI1_DA6) 3 6 PA30 (MCI1_DA7) 4 5 RR39 RR42 27R RR36 10k J5 8 7 6 5 4 3 2 1 9 C123 100n 3V3

SD/MMCPlus CARD INTERFACE - MCI1

Figure 4-18. SD/MMC1

PD10 PA[0..5] (RCIO_CD) PA3 (MCIO_DA1) 1 8 PA2 (MCIO_DA0) 2 7 PA0 (MCIO_CK) 3 6 PA1 (MCIO_CDA) 4 5 PA5 (MCIO_DA3) 1 8 PA4 (MCIO_DA2) 2 7 RF38 27R 68K 68K 68K 68K H167 H188 H189 H190 3V3 H65 10k J6 C122 100nC122 100n 3V3 RR40 27RR40 27R J6 12 11 10

SD/MMC CARD INTERFACE - MCI0

4.2.13 TFT LCD with Touch Panel

The SAM9M10 features an LCD controller. A 4.3" 480x272 Portrait Mode LCD provides the SAM9M10-G45-EK with a low power LCD display, back light unit and a touch panel, similar to that used on commercial PDAs.

The TFT LCD component is a truly model number TFT1N4633.

Graphics and text can be displayed on the dot matrix panel with up to 16 million colors by supplying 24-bit data signals (8bitxRGB by default) or 16-bit data signals (5+6+5bitxRGB in option). This allows the user to develop graphical user interfaces for a wide variety of end applications.

Warning: never connect/disconnect the LCD display from the board while the power supply is on. Doing so may damage both units and is not covered by warranty.

The back light voltage is generated from a CP2122ST boost converter. It is powered directly by the VIN 5 VCC power (the control for the back light voltages is separated from the main board voltages due to the specific voltage requirements of the LCD panel).

Figure 4-19. TFT LCD

	R17	CNP517 ONP	PE24
BLUE7	R170	CNP517 ONR	PE25
BLUE6	R180	CNP516 ONP	PE23
	R180	CNP516 ONR	PE25
BLUE5	R187	CNP5167 ONP	PE22
	R186	OR	PE24
BLUE4	R186	CNP5165 ONP	PE21
	R186	CNP5166 ON	PE22
BLUE3	R183	CNP5165 ONP	PE25
	R182	OR	PE26
GREEN7	R181	CNP5165 ONP	PE18
	R180	CNP5166 ON	PE22
GREEN6	R180	CNP5165 ONP	PE17
	R180	CNP5166 ON	PE21
GREEN5	R187	CNP5165 ONP	PE16
	R186	CNP5166 ON	PE25
GREEN4	R185	CNP5165 ONP	PE15
	R185	CNP5166 ON	PE15
GREEN3	R183	CNP5165 ONP	PE14
	R182	CNP5166 ON	PE18
GREEN2	R181	CNP5165 ONP	PE13
	R180	OR	PE17
RED7	R149	CNP5149 ONP	PE19
	R148	CNP5148 ON	PE14
RED6	R147	CNP5147 ONP	PE11
	R146	OR	PE13
RED5	R145	ONP	PE10
	R144	CNP5146 ON	PE12
RED4	R144	CNP5146 ONP	PE9
	R143	CNP5145 ON	PE11
RED3	R143	CNP5145 ONP	PE9
	R142	CNP5144 ON	PE10

Board Description

4.2.14 Push Buttons

The SAM9M10-G45-EK is equipped with two system push buttons, two user push buttons and one joystick. The push buttons consist of momentary push button switches mounted directly to the board. When any switch is depressed, a low (zero) appears at the associated input pin.

■ System push buttons:

• Reset, perform system reset
  – Wakeup, perform system wake up

■ User push button:

• Right click
• Left click

■ Joystick:

• One touch, 5-way switching,
  – Normally open momentary contacts,
• Push down to select in any position.

Figure 4-20. Push Buttons

VDDBU 3V3 R23 100k R24 1k BP1BP1 BP2BP2 NRST WAKE UP BP4BP4 WAKE UP RIGHT CLICK C31 10n R27 100R PB7 LEFT CLICK C37 10n R29 100R PB6

4.2.15 Expansion Slot

■ GPIO1 & GPIO2, LCD signals (PIO E) are routed to the connectors extension J23
■ All I/Os of the SAM9M10 Image Sensor Interface are routed to connectors J17
■ Touch screen signals and analog I/O are connected to J18

This allows the developer to extend the features of the board by adding external hardware components or boards.

Figure 4-21. Expansion Slot

CONNECTOR EXTENSION FOR LARGE LCD J23 DNP PE8 1 2 PE7 PE10 34 PE9 PE12 5 6 PE11 PE14 7 8 PE13 PE16 9 10 PE15 PE18 11 12 PE17 PE20 13 14 PE19 PE22 15 16 PE21 PE24 17 18 PE22 PE26 19 20 PE23 PE28 21 22 PE27 PE30 23 24 PE29 LCDHSYNC LCDDDYCK PD14 3V3 HD R 2x20 SMT J18 1 2 (AD0Xp) 34 5 7.8 9 11.2 13 15 17 19 20 R175 CR DNP 3V3 HD R 2x10 SMT DNP LCDHSYNC LCDDDYCK PD16 PD20 PD22 PD24 PD26 PD18 5V 3V3

IMAGE SENSOR CONNECTOR VDD/S PD12 PA21 J17 34 5 7.8 5 11.12 13 15 17 19 21.20 23.24 25.26 27.28 29.30 HOR 2x15 SMT 3V3 C210 100n C211 10u 10V C212 100n P20 PB31 PB29 PB30 PB26 PB20 PB22 PB24 PB26 PB8 PB10

5.1 JTAG/ICE Configuration

Table 5-1. JTAG/ICE Configuration

Designation	Default Setting Feature
R91 Not populated Disables the ICE NTRST input
R92 Soldered Enables the ICE RTCK return. R94 must be opened
R93 Soldered Enables the ICE NRST input
R94 Not populated Disables TCK <-> RTCK local loop

5.2 ETHERNET Configuration

RMII is the factory default mode.

To evaluate the MII mode, the user has to unsolder R99 and solder R100, R103 to R105, R108 to R110, R112, R114, C174, C175, Y5.

5.3 Jumpers Configuration

Two types of jumpers are used on the SAM9M10-G45-EK board:

■ 2-pin jumpers with two possible settings:

– Fitted: the circuit is closed

- Not fitted: the circuit is open

■ 3-pin jumpers with two possible positions, for which settings are presented in the following tables.

Table 5-2. Jumpers Configuration

Designation	Default Setting Feature
J1 (combined jumper array)	Closed			J1-1	1-2
	Closed			J1-2	3-4
	Closed			J1-3	5-6
	Closed J1-4	7-8 VDDPLLUTMI 1V
JP1 1-2 JP1			1-2 VDDIOP0 3V3
			2-3 External power to VDDIOP0 3V3 nominal
JP2 1-2 JP2			1-2 VDDIOP1 3V3
			2-3 External power to VDDIOP1 3V3 nominal
JP3 1-2 JP3			1-2 VDDIOP2 3V3
			2-3 External power to VDDIOP2 3V3 nominal
JP4 Opened		Forces power on.To use the software shutdown control, JP4 must be opened.3V battery backup must be present and JP7 jumper set in position 1-2
JP5 1-2 JP5			1-2 VDDIOM0		1V8
			2-3 External power to VDDIOM0		1V8 nominal
JP6 1-2 JP6			1-2 VDDIOM1		1V8
			2-3 External power to VDDIOM1		1V8 nominal
JP7 1-2 JP7			1-2 VDDBU		Lithium 3V Battery
			2-3 VDDBU		3.3V from regulator
JP8 Opened		BMS Enables Boot on the internal ROM; closed selects the boot from the external device connected to NCS0
JP9	Closed	Enables chip select access, Boot on the NCS0 (MN10 Flash)
JP10	Closed	Enables chip select access, Boot on the NCS3 (MN11 NAND Flash)
JP11	Test point	JP11.1: SO		JP11.2: SI	JP11.3: SCK
JP12	Closed	Enables chip select access, Boot on the SPIO_NPCS0 (Serial DataFlash MN13)
JP13	Opened	Set address A0 low (MN12 Serial EEPROM), enable Boot access.
JP14		JP14.1 = Line_Out		JP14.3 = AGND
JP15		Used to connect a Loudspeaker
JP16	Closed	DISMDIX (MN18)
JP17-JP18	Test points	Give access to the four GPIOs of WM9711L

5.4 Miscellaneous Configuration Items

N.P = not populated

P = populated

Table 5-3. Miscellaneous Configuration

Designation	Default Setting Feature
R34 N.P JTAGSEL
R35 P Connect TSADVREF to VDDANA (may be used for specific filtering)
R36 P Connect GNDANA to GND (may be used for specific filtering)
R38 P Force TST pin to GND (chip is set in non-test mode = normal operation mode)
R63 N.P		Write protect NAND Flash (mount a 0-ohm resistor to write-protect the NAND Flash device)
R68 N.P		Write protect serial DataFlash (mount a 0-ohm resistor to write-protect the serial Flash device)
R75 N.P External clock Audio AC97 (mount a 0-ohm resistor to connect it)
R91,R92 R93,R94		ICE interface reset and clocking schemes (see Section 5.1 "JTAG/ICE Configuration")
R100, R103 to R105, R108 to R110, R112, R114, C174, C175, Y5		Ethernet interface, MII mode (see Section 5.2 "ETHERNET Configuration")
Y6, R184, R186	N.P External 13 MHz oscillator (option) for the on-board video composite encoder
TP1 GND	Test point
TP2 GND	Test point
TP3 GND	Test point
TP4 GND	Test point

5.5 PIO Configuration

5.5.1 Peripheral Signals Multiplexing on I/O Lines

The AT91SAM9M10 product features 5 PIO controllers, PIOA, PIOB, PIOC, PIOD and PIOE, which multiplex the I/O lines of the peripheral set. Each PIO Controller controls up to 32 lines. Each line can be assigned to one of two peripheral functions, A or B. The multiplexing tables in the following paragraphs define how the I/O lines of peripherals A and B are multiplexed on the PIO Controllers.

5.5.2 Multiplexing on PIO Controller A (PIOA)

"R.Select" = connection selectable via an on-board resistor (default not populated)

Table 5-4. PIO Multiplexing Port A

I/O Peripheral A Peripheral B Function and Comments Power
PA0 MCI0_CK TCLK3 M	MCI0 Clock VDDIOP0
PA1 MCI0_CDA TIOA3	MMCI0 Command VDDIOP0
PA2 MCI0_DA0 TIOB3	MMCI0 Data0 VDDIOP0
PA3 MCI0_DA1 TCKL4	MMCI0 Data1 VDDIOP0
PA4 MCI0_DA2	TIOA4 MMCI0 Data2 VDDIOP0
PA5 MCI0_DA3 TIOB4	MMCI0 Data3 VDDIOP0
PA6	MCI0_DA4	ETX2		Ethernet MII		VDDIOP0
PA7	MCI0_DA5	ETX3		Ethernet MII		VDDIOP0
PA8	MCI0_DA6	ERX2		Ethernet MII		VDDIOP0
PA9	MCI0_DA7	ERX3		Ethernet MII		VDDIOP0
PA10	ETX0			Ethernet RMII Transmit data 0		VDDIOP0
PA11	ETX1			Ethernet RMII Transmit data 1		VDDIOP0
PA12	ERX0			Ethernet RMII Receive data 0		VDDIOP0
PA13	ERX1			Ethernet RMII Receive data 1		VDDIOP0
PA14	ETXEN			Ethernet RMII Transmit enable		VDDIOP0
PA15	ERXDV			Ethernet RMII Receive data valid		VDDIOP0
PA16	ERXER			Ethernet RMII Receive Error		VDDIOP0
PA17	ETXCK			Ethernet RMII Transmit Clock		VDDIOP0
PA18	EMDC			Ethernet RMII Manag.Data Clock		VDDIOP0
PA19	EMDIO			Ethernet RMII Manag.Data In/Out		VDDIOP0
PA20	TWD0			Two Wire Interface Data		VDDIOP0
PA21	TWCK0			Two Wire Interface Clock		VDDIOP0
PA22	MCI1_CDA SCK3		MMCI1 Command VDDIOP0
PA23	MCI1_DA0	RTS3		MMCI1 Data0		VDDIOP0
PA24	MCI1_DA1	CTS3		MMCI1 Data1		VDDIOP0
PA25	MCI1_DA2 PWM3		MMCI1 Data2 VDDIOP0
PA26	MCI1_DA3	TIOB2 MMCI1 Data3 VDDIOP0
PA27	MCI1_DA4	ETXER	R.Select	MMCI1 Data4	Ethernet MII	VDDIOP0
PA28	MCI1_DA5	ERXCK	R.Select	MMCI1 Data5	Ethernet MII	VDDIOP0
PA29	MCI1_DA6	ECRS	R.Select	MMCI1 Data6	Ethernet MII	VDDIOP0
PA30	MCI1_DA7	ECOL	R.Select	MMCI1 Data7	Ethernet MII	VDDIOP0
PA31	MCI1_CK	PCK0		MMCI1_clock		VDDIOP0

5.5.3 Multiplexing on PIO Controller B (PIOB)

Table 5-5. PIO Multiplexing Port B

I/O Peripheral A Peripheral B Function and Comments Power
PB0		SPI0_MISO		SPI	Slave
PB1 SPI0_MOSI SPI Slave In Serial Data Flash VDDIOP0
PB2 SPI0_SPCK SPI Serial Clock Serial DataFlash VDDIOP0
PB3 SPI0_NPCS0	SPI Chip Select Serial DataFlash VDDIOP0
PB4		TXD1		USART1	Transmit
PB5 RXD1	USART1 Receive Data			VDDIOP0
PB6	TXD2			User Push Button Right click	VDDIOP0
PB7	RXD2			User Push Button Left click	VDDIOP0
PB8	TXD3	ISI_D8		Image Sensor Data 8	VDDIOP2
PB9	RXD3	ISI_D9		Image Sensor Data 9	VDDIOP2
PB10	TWD1	ISI_D10		Image Sensor Data 10	VDDIOP2
PB11	TWCK1	ISI_D11		Image Sensor Data 11	VDDIOP2
PB12	DRXD			DBGU Receive Data	VDDIOP0
PB13	DTXD			DBGU Transmit Data	VDDIOP0
PB14	SPI1_MISO			Joystick Left	VDDIOP0
PB15	SPI1_MOSI	CTS0		Joystick Right	VDDIOP0
PB16	SPI1_SPCK	SCK0		Joystick Up	VDDIOP0
PB17	SPI1_NPCS0	RTS0		Joystick Down	VDDIOP0
PB18	RXD0	SPI0_NPCS1		Joystick Push	VDDIOP0
PB19	TXD0	SPI0_NPCS2		UsbVbus	VDDIOP0
PB20	ISI_D0			Image Sensor Data 0	VDDIOP2
PB21	ISI_D1			Image Sensor Data 1	VDDIOP2
PB22	ISI_D2			Image Sensor Data 2	VDDIOP2
PB23	ISI_D3			Image Sensor Data 3	VDDIOP2
PB24	ISI_D4			Image Sensor Data 4	VDDIOP2
PB25	ISI_D5			Image Sensor Data 5	VDDIOP2
PB26	ISI_D6			Image Sensor Data 6	VDDIOP2
PB27	ISI_D7			Image Sensor Data 7	VDDIOP2
PB28	ISI_PCK			Image Sensor Data Clock	VDDIOP2
PB29	ISI_VSYNC			Image Sensor Vertical Synchro	VDDIOP2
PB30	ISI_HSYNC			Image Sensor Horizontal Synchro	VDDIOP2
PB31	ISI_MCK	PCK1		Image Sensor Reference Clock	VDDIOP2

5.5.4 Multiplexing on PIO Controller C (PIOC)

Table 5-6. PIO Multiplexing Port C

I/O Peripheral A Peripheral B Function and Comments Power
PC0		DQM2
PC1		DQM3
PC2 A19 Add19 NAND Flash VDDIOM1
PC3 A20 Add20 NAND Flash VDDIOM1
PC4		A21/NA	NDALE		ALE NAND Flash VDI
PC5 A22/NANDCLE			CLE NAND Flash		VDDIOM1
PC6		A23
PC7		A24
PC8	CFCE1			Ready/Busy NAND Flash	VDDIOM1
PC9			CFCE2	RTS2
PC10			NCS4/CFCS0	TCLK2
PC11			NCS5/CFCS1	CTS2
PC12		A25/CFRNW
PC13		NCS2
PC14	NCS3/NANDCS			Chip select NAND Flash	VDDIOM1
PC15		NWAIT
PC16		D16
PC17		D17
PC18		D18
PC19		D19
PC20		D20
PC21		D21
PC22		D22
PC23		D23
PC24		D24
PC25		D25
PC26		D26
PC27		D27
PC28		D28
PC29 D29					VDDIOM1
PC30 D30					VDDIOM1
PC31 D31					VDDIOM1

5.5.5 Multiplexing on PIO Controller D (PIOD)

Table 5-7. PIO Multiplexing Port D

I/O Peripheral A Peripheral B Function and Comments Power
PD0	TK0	PWM3	Command	LED2 VDDIOP0
PD1 TF0	Output ENA USB Host VDDIOP0
PD2 TD0	Input FLGA USB Host			VDDIOP0
PD3	RD0	Output	ENB USB Host	VDDIOP0
PD4	RK0	Input FLGB USB Host		VDDIOP0
PD5	RF0			Int. Ethernet 10/100 MDINTR	VDDIOP0
PD6	AC97RX			AC97 Receive Signal	VDDIOP0
PD7	AC97TX	TIOA5		AC97 Transmit Signal	VDDIOP0
PD8	AC97FS	TIOB5		AC97 Frame Sync Signal	VDDIOP0
PD9	AC97CK	TCLK5		AC97 Clock Signal	VDDIOP0
PD10	TD1			Card Detect MMCI0 MCI0_CD	VDDIOP0
PD11	RD1			Card Detect MMCI1 MCI1_CD	VDDIOP0
PD12	TK1	PCK0		CTRL1 Image Sensor Interface	VDDIOP0
PD13	RK1			CTRL2 Image Sensor Interface	VDDIOP0
PD14	TF1			GPIO1 Large LCD (connector)	VDDIOP0
PD15	RF1			GPIO2 Large LCD (connector)	VDDIOP0
PD16	RTS1			USART1 Request to Send	VDDIOP0
PD17	CTS1			USART1 Clear To Send	VDDIOP0
PD18	SPI1_NPCS2	IRQ			VDDIOP0
PD19	SPI1_NPCS3	FIQ			VDDIOP0
PD20	TIOA0		TSAD0	Touch screen X_Right	VDDANA
PD21	TIOA1		TSAD1	Touch screen X_Left	VDDANA
PD22	TIOA2		TSAD2	Touch screen Y_Up	VDDANA
PD23	TCLK0		TSAD3	Touch screen Y_Down	VDDANA
PD24	SPI0_NPCS1	PWM0	GPAD4	General purpose A/D4	VDDANA
PD25	SPI0_NPCS2	PWM1	GPAD5	General purpose A/D5	VDDANA
PD26	PCK0	PWM2	GPAD6	General purpose A/D6	VDDIOP0
PD27	PCK1	SPI0_NPCS3	GPAD7	General purpose A/D7	VDDIOP0
PD28	TSADTRG	SPI1_NPCS1		USB Plug-ID IDUSB	VDDIOP0
PD29	TCLK1	SCK1		MCI1_WP	VDDIOP0
PD30	TIOB0	SCK2		Command Power Led	VDDIOP0
PD31	TIOB1	PWM1		Command LED1 VDDIOP0

5.5.6 Multiplexing on PIO Controller E (PIOE)

Table 5-8. PIO Multiplexing Port E

I/O Peripheral A Peripheral B Function and Comments Power
PE0 LCD PWR PCK0 LCD Panel Pow.Enab.Ctrl VDDIOP1
PE1 LCDMOD LCD Modulation Signal VDDIOP1
PE2 LCDCC LCD Contrast Control VDDIOP1
PE3 LCDVSYNC LCD Vertical Synch.				VDDIOP1
PE4	LCDHSYNC			LCD Horizontal Synch.	VDDIOP1
PE5	LCDDOTCK			LCD Dot Clock	VDDIOP1
PE6 LCDDEN		LCD Data Enable		VDDIOP1
PE7 LCDD0		LCDD2	LCD-Red0		VDDIOP1
PE8 LCDD1		LCDD3	LCD-Red1		VDDIOP1
PE9 LCDD2		LCDD4	LCD-Red2		VDDIOP1
PE10	LCDD3	LCDD5		LCD-Red3	VDDIOP1
PE11	LCDD4	LCDD6		LCD-Red4	VDDIOP1
PE12	LCDD5	LCDD7		LCD-Red5	VDDIOP1
PE13	LCDD6	LCDD10		LCD-Red6	VDDIOP1
PE14	LCDD7	LCDD11		LCD-Red7	VDDIOP1
PE15	LCDD8	LCDD12		LCD-Green0	VDDIOP1
PE16	LCDD9	LCDD13		LCD-Green1	VDDIOP1
PE17	LCDD10	LCDD14		LCD-Green2	VDDIOP1
PE18	LCDD11	LCDD15		LCD-Green3	VDDIOP1
PE19	LCDD12	LCDD18		LCD-Green4	VDDIOP1
PE20	LCDD13	LCDD19		LCD-Green5	VDDIOP1
PE21	LCDD14	LCDD20		LCD-Green6	VDDIOP1
PE22	LCDD15	LCDD21		LCD-Green7	VDDIOP1
PE23	LCDD16	LCDD22		LCD-Blue0	VDDIOP1
PE24	LCDD17	LCDD23		LCD-Blue1	VDDIOP1
PE25	LCDD18			LCD-Blue2	VDDIOP1
PE26	LCDD19			LCD-Blue3	VDDIOP1
PE27	LCDD20			LCD-Blue4	VDDIOP1
PE28	LCDD21			LCD-Blue5	VDDIOP1
PE29	LCDD22			LCD-Blue6	VDDIOP1
PE30	LCDD23			LCD-Blue7	VDDIOP1
PE31	PWM2	PCK1		AC97 External Clock	VDDIOP1

6.1 Power Supply

The SAM9M10-G45-EK evaluation board can be powered from a DC 5V power supply via the external power supply jack (J2) shown in Figure 6-1. The positive pole must be on J2 center pin.

Figure 6-1. Power Supply Connector J2

Table 6-1. Power Supply Connector J2 Signal Description

Pin Mnemonic Signal description
1 Center	+5 VCC
2	Gnd

6.2 RS232 Connector with RTS/CTS Handshake Support

Connector J11 is the COM1 connector.

Figure 6-2. RS232 COM1 Connector J11

Table 6-2. Serial COM1 Connector J11 Signal Descriptions

Pin Mnemonic Signal description
1, 4, 6, 9 NC	NO CONNECTION
2 TXD TRANSMITTED DATA RS232 serial data output signal
3 RXD RECEIVED DATA RS232 serial data input signal
5 GND GROUND
7 RTS READY TO SEND Active-positive		RS232 input signal
8 CTS CLEAR TO SEND Active-positive		RS232 output signal

6.3 DBGU

Connector J10 is the DBGU connector.

Figure 6-3. RS232 DBGU Connector J10

Table 6-3. RS232 DBGU Connector J10 Signal Descriptions

Pin Mnemonic	Signal description
1, 4, 6, 7, 8, 9	NC	NO CONNECTION
2	TXD TRANSMITTED DATA	RS232 serial data output signal
3	RXD RECEIVED DATA	RS232 serial data input signal
5	GND	GROUND

6.4 Ethernet

Connector J15 is the RJ-45 Ethernet Connector.

Figure 6-4. Ethernet RJ45 Connector J15
12345678

Simple gray electrical connector icon with four slots (no text or symbols)

Table 6-4. Ethernet RJ45 Connector J15 Signal Descriptions

Pin Mnemonic Pin Mnemonic
1 TxData+ DIFFERENTIAL OUTPUT PLUS 2 Txdata-		DIFFERENTIAL OUTPUT MINUS
3 RxData+ DIFFERENTIAL INPUT PLUS 4 Shield
5 Shield 6 RxData- DIFFERENTIAL INPUT MINUS
7	S h i e l d	8	S h i e l d

6.5 USB Host

Connector J12 is the USB Host connector.

Figure 6-5. USB Host type A connector J12

1 2 3 4

Table 6-5. USB Host Type A Connector J12 Signal Descriptions

Pin	Mnemonic	Signal description
1	Vbus	5v power
2	DM	Data minus
3	DP	Data plus
4	Gnd	Ground
5	Shield	Shield

6.6 USB Host/Device

Connector J14 is the USB Host/Device connector.

Figure 6-6. USB Host/Device Micro AB connector J14

1 2 3 4 5

Table 6-6. USB Host/Device MicroAB Connector J14 Signal Descriptions

Pin Mne	monic Signal description
1 Vbus	5v power
2	DM	Data	mir
3 DP D	data plus
4 ID On the Go Identification
5 Gnd Ground

6.7 JTAG Debugging Connector

Connector J13 is the JTAG/ICE connector.

A SAM-ICE connector is a 20-way Insulation Displacement Connector (IDC) keyed box header (2.54 mm male) that mates with IDC sockets mounted on a ribbon cable.

Figure 6-7. JTAG/ICE Connector J13

Pin Mnemonic Description
1 VTref.	3.3V power	This is the target reference voltage. It is used to check if the target has power, to create the logic-level reference for the input comparators, and to control the output logic levels to the target. It is normally fed from VDD on the target board and must not have a series resistor.
2 Vsupply.	3.3V power	This pin is not connected in SAM-ICE. It is reserved for compatibility with other equipment. Connect to VDD or leave open in target system.
3	nTRST TARGET RESET - Active-low output signal that resets the target	JTAG Reset. Output from SAM-ICE to the Reset signal on the target JTAG port. Typically connected to nTRST on the target CPU. This pin is normally pulled HIGH on the target to avoid unintentional resets when there is no connection.
4 GND	Common ground
5	TDI TEST DATA INPUT - Serial data output line, sampled on the rising edge of the TCK signal.	JTAG data input of target CPU. It is recommended that this pin is pulled to a defined state on the target board. Typically connected to TDI on target CPU.
6 GND	Common ground
7 TMS	TEST MODE SELECT	JTAG mode set input of target CPU. This pin should be pulled up on the target. Typically connected to TMS on target CPU. Output signal that sequences the target's JTAG state machine, sampled on the rising edge of the TCK signal.
8	GND	Common
9	TCK TEST CLOCK - Output timing signal, for synchronizing test logic and control register access.	JTAG clock signal to target CPU. It is recommended that this pin is pulled to a defined state on the target board. Typically connected to TCK on target CPU.
10 GND	Common ground
11	RTCK - Input Return test clock signal from the target.	Some targets must synchronize the JTAG inputs to internal clocks. To assist in meeting this requirement, a returned and retimed TCK can be used to dynamically control the TCK rate. SAM-ICE supports adaptive clocking which waits for TCK changes to be echoed correctly before making further changes. Connect to RTCK if available, otherwise to GND
12 GND	Common ground
13	TDO JTAG TEST DATA OUTPUT - Serial data input from the target.	JTAG data output from target CPU. Typically connected to TDO on target CPU.
14 GND	Common ground
15 nSR	ST RESET Active-low reset signal. Target CPU reset signal
16 GND	Common ground
17 RFU	This pin is not connected in SAM-ICE.
18 GND	Common ground
19 RFU	This pin is not connected in SAM-ICE
20 GND	Common ground

6.8 SD/MMC-MCI0

Connector J6 is the SD/MMC connector.

Figure 6-8. SD/MMC0 Connector J6

Technical schematic diagram of a mechanical assembly with numbered components and dashed lines indicating connections or paths.

Table 6-8. SD/MMC0 Connector J6 Signal Descriptions

Pin Mnemonic Pin Mnemonic
1	R S	V	/ D
3 GND	4 VCC
5	C	L	K
7DAT08	DAT1
9	DAT2	10 Card Detect
11	GND	12

A T 3 2 C D G N D

6.9 SD/MMC-MCI1

Connector J5 is the SD/MMC connector.

Figure 6-9. SD/MMC1 Connector J5

SD-WP #8 A#7 #13 CD #12 A#5 #9 A#1 #10 A#2 #11 A#3 A#4 A = (MMCplus&MMCmobile & RS-MMC & MMC & SD)

Table 6-9. SD/MMC1 Connector J5 Signal Descriptions

Pin Mnemonic Pin Mnemonic
1	R S	V	/ D
3 GND 4 VCC
5	C	L	K
7	D	AT0	8
9	DAT2	10	DAT3
11	DAT4	12	DAT5
13	DAT6	14	DAT7

A T 3 2 C M

AT1

6.10 AC97

■ Connector J7 is the Headphone connector.
■ Connector J8 is the Line In connector.
■ Connector J9 is the Microphone Input.
■ Connector JP15 is the Speaker Output connector

Figure 6-10. Audio Connector J7, J8, J9

Technical diagram showing exploded and assembled views of a battery or motor assembly with numbered components

Table 6-10. J7, J8, J9 Signal Description

Pin Mnemonic
1	S
2	S
3	Gnd

i g n a l i g n a l

Table 6-11. Speaker JP15 Signal Descriptions

Pin Mnemonic

1 Speaker bridge output A

2 Speaker bridge output B

6.11 Image Sensor - ISI

Connector J17 is the ISI connector.

Figure 6-11. ISI Connector J17

29 1 30 2

Table 6-12. ISI Connector J17 Signal Descriptions

Pin Mnemonic Pin Mnemonic
1 VCC	3v3 2 Gnd
3 VCC	3v3 4 Gnd
5	C	t	r l
7	S	C	L 8
9	G	n	d 1
11	Gnd	12	ISI_VSYNC
13	Gnd	14	ISI_HSYNC
15	Gnd	16	ISI_PCK
17	Gnd	18	ISI_Data0
19	ISI_Data1	20	ISI_Data2
21	ISI_Data3	22	ISI_Data4
23	ISI_Data5	24	ISI_Data6
25	ISI_Data7	26	ISI_Data8
27	ISI_Data9	28	ISI_Data10
29	ISI_Data11	30	Gnd

1	6	C	t	r
S	D	A
0	I	S	I	_

6.12 Video

Connector J20 is the Video connector

Figure 6-12. Video Connector J20

Table 6-13. Video Connector J20 Signal Description

Pin Mnemonic Signal description
1 Center	Composite video signal output

6.13 Display Devices

6.13.1 TFT LCD

Connector J24 is the TFT-LCD connector.

Figure 6-13. TFT LCD Connector J24

Technical line drawing of a mechanical component with no visible text or symbols

Table 6-14. TFT LCD Connector J24 Signal Descriptions

Pin Mnemonic Pin Mnemonic
1 VLED-	2 VLED+
3 GND 4	VDD 3V3
5	R0	6	R1
7	R2	8	R3
9	R4	10	R5

Table 6-14. TFT LCD Connector J24 Signal Descriptions

Pin	Mnemonic	Pin	Mnemonic
11 R6 12	R7
13 G0 14	G1
15 G2 16	G3
17 G4 18	G5
19 G6 20	G7
21 B0 14	B1
23 B2 16	B3
25 B4 18	B5
27 B6 20	B7
29 GND 30	DCLK
31 DISPON 32	HSYNC
33 VSYNC 34	LCDEN
35 NO CONNECT 36	GND
37 X2 38	Y1
39 X1 40	Y2

6.14 LCD Extension

Connectors J23 and J18 are for an optional LCD extension (not populated).

Table 6-15. Connector J23 Signal Description for an LCD Extension

Pin		Mnemonic	Pin		Mnemonic
1	PE8	RED Data Signal	2	PE7	RED Data Signal (LSB)
3	PE10	RED Data Signal	4	PE9	RED Data Signal
5	PE12	RED Data Signal	6	PE11	RED Data Signal
7	PE14	RED Data Signal (MSB)	8	PE13	RED Data Signal
9	PE16	GREEN Data Signal	10	PE15	GREEN Data Signal (LSB
11	PE18	GREEN Data Signal	12	PE17	GREEN Data Signal
13	PE20	GREEN Data Signal	14	PE19	GREEN Data Signal
15	PE22	GREEN Data Signal (MSB)	16	PE21	GREEN Data Signal
17	PE24	BLUE Data Signal	18	PE23	BLUE Data Signal (LSB)
19	PE26	BLUE Data Signal	20	PE25	BLUE Data Signal
21	PE28	BLUE Data Signal	22	PE27	BLUE Data Signal
23	PE30	BLUE Data Signal (MSB)	24	PE29	BLUE Data Signal
25	PE4	LCDHSYNC	26	PE3	LCDVSYNC
27	PE5	LCDDOTCK	28	GND	(0V)
29	GND	(0V)	30	NC

Table 6-15. Connector J23 Signal Description for an LCD Extension

Pin		Mnemonic	Pin		Mnemonic
31 PE6	LCDDEN 32	PE2 LCDCC
33 PE0	DISPON 34	PE1 LCDMOD
35 PD14	GPIO1 36	PD15 GPIO2
37 GND	(0V) 38 GND	(0V)
39	VCC	+3V3 power source	40	NC

Table 6-16. Connector J18 Signal Description for an LCD Extension

Pin		Mnemonic	Pin		Mnemonic
1	XM	AD1XM	2	XP	AD0XP
3	YM	AD3YM	4	YP	AD2YP
5	GND	(0V)	6	GND	(0V)
7	PD25	PD25	8 PD24	PD24
9	PD27	PD27	10	PD26	PD26
11 PD19	PD19	12	PD18	PD18
13	GND	(0V)	14 GND	(0V)
15	GND	(0V)	16		+5V
17	GND	(0V)	18 GND	(0V)
19	VCC	+3V3 power source	20	VCC	+3V3 power source

7.1 Schematics

This section contains the following schematics:

■ Top Level view, block architecture of the design
■ Power Supply
■ SAM Processor
■ Bus impedance adaptor
■ Main memory
■ EBI memory
■ MCI & TWI
■ Audio AC97
■ Serial interfaces
- Ethernet
LCD
■ Video interfaces and LCD extension

graph TD
    subgraph Power Supply
        A["5V POWER SUPPLY"] -->|PI0| B["ATMEL ARM9 Processor SAM9M10 (LFBGA324)"]
    end

    subgraph I/O Interface
        C["RS232 DBGU COM1"] -->|PIO| B
        D["USB HOST"] -->|PIO| B
        E["14 HOST DEVICE"] -->|PIO| B
        F["ICE INTERFACE"] -->|PIO| B
        G["10-100 FAST ETHERNET"] -->|PIO| B
    end

    subgraph Card Reader
        H["CARD READER"] --> I["AUDIO"]
        I --> J["MICOUT IN"]
        J --> K["Sheet 8"]
        L["RAMS 256MB"] --> M["Sheet 7"]
    end

    A -->|3V3 1VB 1V| B
    B -->|EBI0 DDR2 INTERFACE| M
    B -->|EBI1 DATA INTERFACE| N["RES.ARRAYS EBIO_EBI1 ADAPTER"]
    B -->|EBI1 ADDRESS INTERFACE| N
    B -->|EBI1 BUS INTERFACE| N
    N --> O["ESBIO DDR2 INTERFACE"]
    N --> P["ESBIO NANDFLASH INTERFACE"]
    N --> Q["ESB1 DDR2 INTERFACE"]
    N --> R["ESB1 FLASH INTERFACE"]
    N --> S["ESB1 DDR2 INTERFACE"]
    N --> T["ESBIO DDR2 128MB"]
    N --> U["ESBIO FLASH"]
    N --> V["ESBIO CARD READER"]
    N --> W["ESBIO CARD READER"]
    N --> X["ESBIO CARD READER"]
    N --> Y["ESBIO CARD READER"]
    N --> Z["ESBIO CARD READER"]
    N --> AA["ESBIO CARD READER"]
    N --> AB["ESBIO CARD READER"]
    N --> AC["ESBIO CARD READER"]
    N --> AD["ESBIO CARD READER"]
    N --> AE["ESBIO CARD READER"]
    N --> AF["ESBIO CARD READER"]
    N --> AG["ESBIO CARD READER"]
    N --> AH["ESBIO CARD READER"]
    N --> AI["ESBIO CARD READER"]
    N --> AJ["ESBIO CARD READER"]
    N --> AK["ESBIO CARD READER"]
    N --> AL["ESBIO CARD READER"]
    N --> AM["ESBIO CARD READER"]
    N --> AN["ESBIO CARD READER"]
    N --> AO["ESBIO CARD READER"]
    N --> AP["ESBIO CARD READER"]
    N --> AQ["ESBIO CARD READER"]
    N --> AR["ESBIO CARD READER"]
    N --> AS["ESBIO CARD READER"]
    N --> AT["ESBIO CARD READER"]
    N --> AU["ESBIO CARD READER"]
    N --> AV["ESBIO CARD READER"]
    N --> AW["ESBIO CARD READER"]
    N --> AX["ESBIO CARD READER"]
    N --> AY["ESBIO CARD READER"]
    N --> AZ["ESBIO CARD READER"]
    N --> BA["ESBIO CARD READER"]
    N --> BB["ESBIO CARD READER"]
    N --> BC["ESBIO CARD READER"]
    N --> BD["ESBIO CARD READER"]
    N --> BE["ESBIO CARD READER"]
    N --> BF["ESBIO CARD READER"]
    N --> BG["ESBIO CARD READER"]
    N --> BH["ESBIO CARD READER"]
    N --> BI["ESBIO CARD READER"]
    N --> BJ["ESBIO CARD READER"]
    N --> BK["ESBIO CARD READER"]
    N --> BL["ESBIO CARD READER"]
    N --> BM["ESBIO CARD READER"]
    N --> BN["ESBIO CARD READER"]
    N --> BO["ESBIO CARD READER"]
    N --> BP["ESBIO CARD READER"]
    N --> BQ["ESBIO CARD READER"]
    N --> BR["ESBIO CARD READER"]
    N --> BS["ESBIO CARD READER"]
    N --> BT["ESBIO CARD READER"]
    N --> BU["ESBIO CARD READER"]
    N --> BV["ESBIO CARD READER"]
    N --> BW["ESBIO CARD READER"]

			10-APF-10/A2
A			05-Feb-12	11-FEB-10
REV.	DRAWN.F.	DES.	DATE	VER.
SCALE: 1/1				REV. SHEET A2 2/12

P80.317-12 L80 13 P82 15 P82 16 P82 17 P82 18 P82 19 P82 20 P82 21 P82 22 P82 23 P82 24 P82 25 P82 26 P82 27 P82 28 P82 29 P82 30 P82 31 P82 32 P82 33 P82 34 P82 35 P82 36 P82 37 P82 38 P82 39 P82 40 P82 41 P82 42 P82 43 P82 44 P82 45 P82 46 P82 47 P82 48 P82 49 P82 50 P82 51 P82 52 P82 53 P82 54 P82 55 P82 56 P82 57 P82 58 P82 59 P82 60 P82 61 P82 62 P82 63 P82 64 P82 65 P82 66 P82 67 P82 68 P82 69 P82 70 P82 71 P82 72 P82 73 P82 74 P82 75 P82 76 P82 77 P82 78 P82 79 P82 80 P82 81 P82 82 P82 83 P82 84 P82 85 P82 86 P82 87 P82 88 P82 89 P82 90 P82 91 P82 92 P82 93 P82 94 P82 95 P82 96 P82 97 P82 98 P82 99 P82 100 EIB1_101-104 EBD-01 H6 EBD-01 H4 EBD-01 H3 EBD-01 H2 EBD-01 H1 EBD-01 H0 EBD-01 H9 EBD-01 H7 EBD-01 H5 EBD-01 H3- EBD-01 H1- EBD-01 H9- EBD-01 H7- EBD-01 H5- EBD-01 H3- EBD-01 H1- EBD-01 H9- EBD-01 H7- EBD-01 H5- EBD-01 H3- EBD-01 H1- EBD-01 H9- EBD-01 H7- EBD-01 H5- EBD-01 H3- EBD-01 H1- EBD-10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H10H

EBI Bus Impedance Adaptor

EBIO EBIO 02 2 RMB 7 DOR 32 EBIO 01 4 RMD 5 DOR 31 EBIO 02 2 RSB 7 DOR 32 EBIO 01 1 RBA 8 DOR 33 EBIO 04 3 RAC 6 DOR 34 EBIO 05 4 RBD 3 DOR 35 EBIO 05 1 RBA 8 DOR 36 EBIO 07 3 RBC 5 DOR 37 EBIO 08 2 RMB 7 DOR 38 EBIO 09 4 RBD 5 DOR 39 EBIO D:0 2 RBD 5 DOR 310 EBIO D:1 2 RMB 7 DOR 311 EBIO D:2 1 RBA 8 DOR 312 EBIO D:3 3 RBC 6 DOR 313 EBIO D:4 1 RBA 8 DOR 314 EBIO D:5 3 RBC 6 DOR 315

EER_A1 1 ENRMA 6 DOR_A2 EER_A2 2 ENRMA 7 DOR_A3 EER_A3 3 ENRCA 8 DOR_A4 EER_A4 4 ENRCA 9 DOR_A5 EER_A5 5 ENRCA 10 DOR_A6 EER_A6 6 ENRCA 11 DOR_A7 EER_A7 7 ENRCA 12 DOR_A8 EER_A8 8 ENRCA 13 DOR_A9 EER_A9 9 ENRCA 14 DOR_A10 EER_A10 10 ENRCA 15 DOR_A11 EER_A11 11 ENRCA 16 DOR_A12 EER_A12 12 ENRCA 17 DOR_A13 EER_A13 13 ENRCA 18 DOR_A14 3 ENRCA 19 4 ENRCA 20

E80_CNE5 E80_CL93 E80_NCK16 E80_BACK E80_BACK E80_WST3 E80_CS16 E80_RACK E80_DACK E80_DACK E80_DACK E80_COS14 R40 27F R42 27F R44 27F 1 R110 5 1 RSMA 3 3 R110 5 2 RSMA 7 3 R210 5 1 RSMA 3 1 RSMA 7 R46 27F R48 27F DOR_CKE [I] DOR_CUL [I] DOR_CLUX [I] DOR_BAG [I] DOR_BAY [I] DOR_WE [I] DOR_OB [I] DOR_AIB [I] DOR_CAS [I] DOR_DCK [I] DOR_DCK [I] DOR_DCK [I] DOR_DCK [I] DOR_DCK [I]

EBI 20 1 EBITA 8 EBI FLASH-03 2 EBIT 7 EBI NAND FSH-03 EBI 21 1 EBITA 8 EBI FLASH-01 2 EBIT 7 EBI NAND FSH-01 4 EBITD 5 EBI FLASH-02 3 EBITC 5 EBI NAND FSH-02 4 EBIT 5 EBI FLASH-03 EBI 23 1 EBITA 8 EBI FLASH-04 2 EBIT 7 EBI NAND FSH-04 3 EBITC 5 EBI FLASH-05 4 EBITD 5 EBI NAND FSH-05 EBI 25 1 EBITA 8 EBI FLASH-06 2 EBIT 7 EBI NAND FSH-06 3 EBITC 5 EBI FLASH-07 4 EBITD 5 EBI NAND FSH-07 EBI 26 4 EBITD 5 EBI FLASH-08 3 EBITC 5 EBI NAND FSH-08 EBI 29 2 EBITB 7 EBI FLASH-09 1 EBITA 8 EBI NAND FSH-09 2 EBITC 5 EBI FLASH-010 4 EBITD 5 EBI NAND FSH-010 EBI 310 2 EBITB 7 EBI FLASH-011 1 EBITA 8 EBI NAND FSH-011 2 EBITC 5 EBI FLASH-012 4 EBITD 5 EBI NAND FSH-013 EBI 316 4 EBITD 5 EBI FLASH-014 9 EBITC 5 EBI NAND FSH-015 EBI 326 2 EBITB 7 EBI NAND FSH-016 1 EBITA 8 EBI NAND FSH-017 EBI D4 4 RIOU S EB1 COD D4 EBI D7 1 RIOU S EB1 COD D7 EBI D7 2 RIOU S EB1 COD D7 EBI D4 3 RIOU S EB1 COD D4 EBI D4 2 RIOU S EB1 COD D4 EBI D6 1 RIOU S EB1 COD D6 EBI D7 3 RIOU S EB1 COD D7 EBI D8 3 RIOU S EB1 COD D8 EBI D9 1 RIOU S EB1 COD D9 EBI D10 C BING RIOU S EBI D11 4 RIOU S EB1 COD D11 EBI D12 1 RIOU S EB1 COD D12 EBI D13 3 RIOU S EB1 COD D13 EBI D14 C BING RIOU S EBI D15 4 RIOU S EB1 COD D15 EBI D16 C BING RIOU S

EB1 SCORE EB1 SCORE EB1_SOC0 EB1_A16 EB1_A17 EB1_NOB-8COS EB1_SCVE EB1_NOB3 EB1_CARS EB1_DCM3 EB1_DQS CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI CB_EBI

EBI1 EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01 01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D01_D01_01(0) EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI1_D25D7 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBI_A2 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA3 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA4 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA6 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBiA7 EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)## EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)##- EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)### EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)# EBI-A2_01(D)u- EBI-A2_01(D)u- EBI-A2_01(D)u- EBI-A2_01(D)u- EBI-A2_01(D)u- EBI-A2_01(D)u- EBI-A2_01(D)u- EBI-A2_01(D)u- EBI-A2_01(D)u- EBI-A2_01(D)u- FIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3- FIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3-8BIBIA3- FIBIA3-8BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3- FIBIA3-8BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3- FIBIA3-8BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3- FIBIA3-8BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3- FIBIA3-8BIBIA3-9BIBIA3-9BIBIA3-6#- FIBIA3-8BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3- FIBIA3-8BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3-9BIBIA3- FIBIA3-8BIBIA3-9BIBIA3 -6#- FIBIA3-8BIBIA3 -6#- FIBIA3-8BIBIA3 -6#- FIBIA3-8BIBIA3 -6#- FIBIA3-8BIBIA3 -6#- FIBia4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4c- Fibia4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4a4c- Fibia4a5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5c- Fibia4a5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5b5c- Fibia4a6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6e- Fibia4a6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6c6e- Fibia4a7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7d7e- Fibia4a8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8e8f- Fibia4a9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9e9f- Fibia4a9fEEI_BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY-BY

ATMEL ROUNSKY A2 PP 16-A0-10 PF 11-PB-10 A DWK 16-PB-10 PF 11-PB-10 REV. MODE. TYPE. DATE OFFS. DATE AT91SAM9M10 G45-EK SCALE 1/1 REV. SHEET A2 4/12

DDR_D0.15V DDR_A0.19V MFB MT47H4N16CF 3 F DDR_DC0H(1) DDR_DC0H(2) DDR_DC0H(3) DDR_DC0H(4) DDR_DC0H(5) DDR_DC0H(6) DDR_DC0H(7) DDR_DC0H(8) DDR_DC0H(9) DDR_DC0H(10) DDR_DC0H(11) DDR_DC0H(12) DDR_DC0H(13) DDR_DC0H(14) DDR_DC0H(15) DDR_DC0H(16) DDR_DC0H(17) DDR_DC0H(18) DDR_DC0H(19) DDR_DC0H(20) DDR_DC0H(21) DDR_DC0H(22) DDR_DC0H(23) DDR_DC0H(24) DDR_DC0H(25) DDR_DC0H(26) DDR_DC0H(27) DDR_DC0H(28) DDR_DC0H(29) DDR_DC0H(30) DDR_DC0H(31) DDR_DC0H(32) DDR_DC0H(33) DDR_DC0H(34) DDR_DC0H(35) DDR_DC0H(36) DDR_DC0H(37) DDR_DC0H(38) DDR_DC0H(39) DDR_DC0H(40) DDR_DC0H(41) DDR_DC0H(42) DDR_DC0H(43) DDR_DC0H(44) DDR_DC0H(45) DDR_DC0H(46) DDR_DC0H(47) DDR_DC0H(48) DDR_DC0H(49) DDR_DC0H(50) DDR_DC0H(51) DDR_DC0H(52) DDR_DC0H(53) DDR_DC0H(54) DDR_DC0H(55) DDR_DC0H(56) DDR_DC0H(57) DDR_DC0H(58) DDR_DC0H(59) DDR_DC0H(60) DDR_DC0H(61) DDR_DC0H(62) DDR_DC0H(63) DDR_DC0H(64) DDR_DC0H(65) DDR_DC0H(66) DDR_DC0H(67) DDR_DC0H(68) DDR_DC0H(69) DDR_DC0H(70) DDR_DC0H(71) DDR_DC0H(72) DDR_DC0H(73) DDR_DC0H(74) DDR_DC0H(75) DDR_DC0H(76) DDR_DC0H(77) DDR_DC0H(78) DDR_DC0H(79) DDR_DC0H(80) DDR_DC0H(81) DDR_DC0H(82) DDR_DC0H(83) DDR_DC0H(84) DDR_DC0H(85) DDR_DC0H(86) DDR_DC0H(87) DDR_DC0H(88) DDR_DC0H(89) DDR_DC0H(90) DDR_DC0H(91) DDR_DC0H(92) DDR_DC0H(93) DDR_DC0H(94) DDR_DC0H(95) DDR_DC0H(96) DDR_DC0H(97) DDR_DC0H(98) DDR_DC0H(99) DDR_DC0H(D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (D2) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E7) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E6) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E5) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E4) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3) (E3)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1), A1(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A1)(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(A2), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CB), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCC), A2(CCCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(CCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A2(SCL), A8(E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,E8,SCL DDR_BX(HI) DDR_BX(HI) DDR_BX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX(HI) DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDR_CX.HI DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS DDS

A2	PP	19 apr 15
A1		16 Fec 10		11 PEB-100
REV.	DATE	VER.
SCALE	1/1		REV.	SHEET
E=1			A2	5/12

R64 12k R18 R19 R15 R100 R65 12k DC1 DC20 CO1 F43 DC20 DAT1 F42 DC20 DAT2 F40 DC20 GC FA1 DC20 CO4 F45 DC20 DAT5 F43 DC20 DAT3 R105 2/11 1 8 2 7 3 6 4 5 5 4 6 3 7 2 8 1 9 0 10 0 11 0 12 0 13 0 14 0 15 0 16 0 17 0 3V C120 80mA FP58K SP24H

SD/MMC CARD INTERFACE - MCI0

R19 R10 R15 R10 R10 R10 R10 6K 6K M4 6K 6K E6 6K E6 RL RP36 10k AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-22 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-21 AC-20 AC-20 AC-20 AC-20 AC-20 AC-20 AC-20 AC-20 AC-20 AC-20 AC-20 AC-19 AC-19 AC-19 AC-19 AC-19 AC-19 AC-19 AC-19 AC-19 AC-19 AC-18 AC-18 AC-18 AC-18 AC-18 AC-18 AC-18 AC-18 AC-18 AC-18 AC-17 AC-17 AC-17 AC-17 AC-17 AC-17 AC-17 AC-17 AC-17 AC-16 AC-16 AC-16 AC-16 AC-16 AC-16 AC-16 AC-16 AC-16 AC-15 AC-15 AC-15 AC-15 AC-15 AC-15 AC-15 AC-15 AC-15 AC-14 AC-14 AC-14 AC-14 AC-14 AC-14 AC-14 AC-14 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AC-13 AUC 0.0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000

SD/MMCPlus CARD INTERFACE - MCI1

R4213 PA259 110V CCK2 110V 10A 3V8 C125 10A 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 AT280518N MN12 SCL A0 SCA A1 VCC1 A2 CND V7 AT280518N 1 2 3 4 5 6 7 8 9 10 11 12 13 JP13 SP2

SERIAL EEPROM

2nd pin 1 TNP JP1 30Ω 857 470A NFE3 SC Si SCK GSM VOC GS Y AT8083D-SD PDS BI DIP NFE1/LESS >160 SERIAL DATAFLASH

	A2	PP	10-axr 12
	A		16-Fec 10		11-FEB-100x
	RPU/AMMHF	NFR.	DATE	VFR.
AT91SAM9M10 G45 EK	SCALE 1/1			REV.	SHEET
MOB & TWI				A2	7/12

HEADPHONE LINE-OUT 17 STEREO 3.5mm R70 OR C187 100/-6.3V 1 2 2 2 16 220cm at 100kHz R71 4K R72 4K C198 47p C199 49p JP17 DHP JP18 DHP C182 100m C183 10V ACND AC07 JP14 DHP AGND_AC07 R75 DR C185 100m C186 10V C187 100/-6.3V R76 DR C188 100m C189 10V C190 10V C191 10V C192 10V C193 10V C194 10V C195 10V C196 10V C197 10V C198 10V C199 10V C200 10V C201 10V C202 10V C203 10V C204 10V C205 10V C206 10V C207 10V C208 10V C209 10V C210 10V C211 10V C212 10V C213 10V C214 10V C215 10V C216 10V C217 10V C218 10V C219 10V C220 10V C221 10V C222 10V C223 10V C224 10V C225 10V C226 10V C227 AONDA NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/NCFF/ WNRNTL: VINCE, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, CLK, OUT, NLN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INN, INnS/NR/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/R/S/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TX/TxTIN / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR / NCFR< img src="boxc-occi" (boxc-occi) for the circuit design. OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OknO/Occi/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/r/sr/cs/nR75-DCI/DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-A/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C/C-C/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A/B/A-B/A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-A-B-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-C-NR75-DCI/DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DI-DIC NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/NCR/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC(MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/Monic/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/MONIC/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/monio/nR75-DCi/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/Di/DiDl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl Dl AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AOC#AUC#AOC# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JANIOACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JAMID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS## JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANID ACOS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JANIDACOCS# JAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIAIIAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBAAIBBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBAABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBABBBBB B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB BB< img src="boxc-occi" (boxc-occi) for the circuit design. OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK: OK:OKB(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)B(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(BC)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)BB(B)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(BC)LG(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC)(FC) MONO STEREO MICROPHONE INPUT: JP L J S TSTPEC 3.5mm

			10-APR-10P/20
A			03-FEB-15	11-FEB-16
REV.	DAMOND.F.	DES.	DATE	VER.
SCALE 1/1				REV. SHEET A2 8/12

SERIAL DEBUG PORT

L DEBUG PORT J10 6 2 8 5 3 1 5 14 7 13 8 ACM/DC/DATN2 ACM/DC/DATN2 SC9 T162 100V 14 C167 100V 2 C166 100V 5 AN15 VCC C3+ VCC C468 100V VCC C463 100V C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC C3+ VCC D R87 100k R88 100k P8-1 回 P8-2 回

RS232 COM PORT R50 100k R85 100k C160 100n C164 100n MN15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

USB HOST INTERFACE USB HOST/DEVICE INTERFACE J12 G3055-PU811 51W C167 100Ω U8A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

3/8 345 J13 R143 10kV 323 R97 DNP R97 R97 I7RST 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kV 10kW NRS-2.3.7.5.10 kV ICE INTERFACE

			10-APR-10P/20
A			02-Feb-10
REV.	DRAWN/E	DES.	DATE	VER.
SCALE: 1/1				REV. SHEET A2 9/12

RJ45 ETHERNET CONNECTOR RJ45 ETHERNET CONNECTOR C176 100k C175 100k C174 20k C173 20k C172 20k C171 20k C170 20k C169 20k C168 20k C167 20k C166 20k C165 20k C164 20k C163 20k C162 20k C161 20k C160 20k C159 20k C158 20k C157 20k C156 20k C155 20k C154 20k C153 20k C152 20k C151 20k C150 20k C149 20k C148 20k C147 20k C146 20k C145 20k C144 20k C143 20k C142 20k C141 20k C140 20k C139 20k C138 20k C137 20k C136 20k C135 20k C134 20k C133 20k C132 20k C131 20k C130 20k C129 20k C128 20k C127 20k C126 20k C125 20k C124 20k C123 20k C122 20k C121 20k C120 20k C119 20k C118 20k C117 20k C116 20k C115 20k C114 20k C113 20k C112 20k C111 20k C110 20k C109 20k C108 20k C107 20k C106 20k C105 20k C104 20k C103 20k C102 20k C101 20k C100 20k RJ45 ETR/NEUTRAL (RS-ETR) RJ45 ETR/NEUTRAL (RS-ETR) RJ45 ETR/NEUTRAL (RS-ETR) RJ45 ETR/NEUTRAL (RS-ETR) RJ45 ETR/NEUTRAL (RS-ETR) RJ45 ETR/NEUTRAL (RS-ETR) RJ45 ETR/NEUTRAL (RS-ETR) RJ44 ETR/NEUTRAL (RS-ETR) RJ44 ETR/NEUTRAL (RS-ETR) RJ44 ETR/NEUTRAL (RS-ETR) RJ43 ETR/NEUTRAL (RS-ETR) RJ43 ETR/NEUTRAL (RS-ETR) RJ43 ETR/NEUTRAL (RS-ETR) RJ43 ETR/NEUTRAL (RS-ETR) RJ43 ETR/NEUTRAL (RS-ETR) RJ43 ETR/NEUTRAL (RS-ETR) RJ43 ETR/DEUTRAL (RS-ETR) RJ43 ETR/DEUTRAL (RS-ETR) RJ43 ETR/DEUTRAL (RS-ETR) RJ43 ETR/DEUTRAL (RS-ETR) RJ43 ETR/DEUTRAL (RS-ETR) RJ43 ETR/DEUTRAL (RS-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43 ETR/DEUTRAL (RL-ETR) RJ43E TR(ELT-ETT-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG- RESI NC RJ45 ETR/NEUTRAL (RS-ETT-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG-ESG- RESI NC RJ45 ETR/NEUTRAL (RS-ETT-ESG-ESG-ESG-ESG-ESG-ESGs- RESI NC RJ45 ETR/NEUTRAL (RS-ETT-ESGs- RESI NC RJ45 ETR/NEUTRAL (RS-ETT- RESI NC RJ45 ETR/NEUTRAL (RS-ETT- RESI NC RJ45 ETR/NEUTRAL (RS-ETT- RESI NC RJ45 ETR/NEUTRAL (RS-ETT- RESI NC RJ45 ETR/NEUTRAL (RS-ETT- RESI NC RJ45 ETR/NEUTRAL (RS-ETT- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- RESI NC LRTL- REST NC N C NLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SLSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCSU SCS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS USS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SS U SSR A B B C D E F G H I J K L M N O P Q R T X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Y Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZA B C D D E F G H I Y K L M N O P Q R T X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X XX Y Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z Z

		10-APR-10P/20
A		02-FEB-15		11-FEB-16
AT918SAM9M10-C45-EK	REV.	DAMND.F.	DES.	DATE:
	SCALE	1/1		REV.
PMI MII ETHERNET				A2 10/12

A2	PP	19-04-15
A1		16-FBC-10		11-FEB-10
REV.	DATE	VER.
SCALE 1/1			REV.	SHEET 11/12
E=Φ			A2

P01.36V P02.16V P03.16V P04.16V P05.16V P06.16V P07.16V P08.16V P09.16V P10.16V P11.16V P12.16V P13.16V P14.16V P15.16V P16.16V P17.16V P18.16V P19.16V P20.16V P21.16V P22.16V P23.16V P24.16V P25.16V P26.16V P27.16V P28.16V P29.16V P30.16V P31.16V P32.16V P33.16V P34.16V P35.16V P36.16V P37.16V P38.16V P39.16V P40.16V P41.16V P42.16V P43.16V P44.16V P45.16V P46.16V P47.16V P48.16V P49.16V P50.16V P51.16V P52.16V P53.16V P54.16V P55.16V P56.16V P57.16V P58.16V P59.16V P60.16V P61.16V P62.16V P63.16V P64.16V P65.16V P66.16V P67.16V P68.16V P69.16V P70.16V P71.16V P72.16V P73.16V P74.16V P75.16V P76.16V P77.16V P78.16V P79.16V P80.16V P81.16V P82.16V P83.16V P84.16V P85.16V P86.16V P87.16V P88.16V P89.16V P90.16V P91.16V P92.16V P93.16V P94.16V P95.16V P96.16V P97.16V P98.16V P99.16V P100.16V

CONNECTOR EXTENSION FOR LARGE LCD (1) LOGOSYNC (I1) (2) LOGOSTOC PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN PEN

IMAGE SENSOR CONNECTOR Q24C 100V Q211 10V Q212 100V WDOS/HD FD 5.5V JIT 7A1 1 3 4 6 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

A2		PP	08-pp-10
A		Ockk	05 Feb 10	PP	11 FEB 10
P=V	MOEK	D=X	D=Y	V=H	D=J
SCAN = 1/1				REV.	3=FFT
A2				12/12

8.1 Revision History

Table 8-1.

Document Comments		Change Request Ref.
6495B	Main edits:- Most Figures updated- Hyperlinks to PDFs updated- 'Serial Synchronous Controller (SSC)' removed- 'JTAG' added- 'RJ45 crossed cable' added- Dimensions updated- Most configuration tables (with LEDs, pins and connectors) updated- 'LG/Philips' reference removed	6990
	New Figure 4-4," EBI1 - DDR2 + Flash" and new Schematics in Section 7.1 "Schematics"	7169
6495A First issue.

Headquarters International

Atmel Corporation2325 Orchard ParkwaySan Jose, CA 95131USATel: 1(408) 441-0311Fax: [phone]

Atmel AsiaUnit 1-5 & 16, 19/FBEA Tower, Millennium City 5418 Kwun Tong RoadKwun Tong, KowloonHong KongTel: (852) 2245-6100Fax: [phone]

Atmel EuropeLe Krebs8, Rue Jean-Pierre TimbaudBP 30978054 Saint-Quentin-en-Yvelines CedexFranceTel: (33) 1-30-60-70-00Fax: [phone]

Atmel Japan9F, Tonetsu Shinkawa Bldg.1-24-8 ShinkawaChuo-ku, Tokyo 104-0033JapanTel: (81) 3-3523-3551Fax: [phone]

Product Contact

Web Site	Technical Support	Sales Contact
www.atmel.com	AT91SAM Support	www.atmel.com/contacts
	Atmel technical support

Literature Requests

www.atmel.com/literature

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL'S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL'S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel's products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

© 2010 Atmel Corporation. All rights reserved. Atmel ^® , Atmel logo and combinations thereof, DataFlash ^® , and others are registered trademarks, SAM-ICE ^™ and others are trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.