SVVE01160PC - Vacuum Cleaner SVAN - Free user manual and instructions
Find the device manual for free SVVE01160PC SVAN in PDF.
User questions about SVVE01160PC SVAN
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Vacuum Cleaner in PDF format for free! Find your manual SVVE01160PC - SVAN and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. SVVE01160PC by SVAN.
USER MANUAL SVVE01160PC SVAN
SVVE01160PC & SVVE01180R
natural_image
Line drawing of a standard office fan with radial blades and a stand (no text or symbols)LEA Y GUARDE ESTE MANUAL DE INSTRUCCIONES
SVVE01160PC & SVVE01180R
USERS MANUAL
natural_image
Line drawing of a standard office fan with radial blades and a stand (no text or symbols)REMARKS: ELECTRICAL CONNECTIONS SHALL BE IN ACCORDANCE WITH NATIONAL OR LOCAL CODES.
READ AND SAVE THIS INSTRUCTION MANUAL
Sleek & modern high-velocity fan provides more powerful wind than ordinary plastic fans. Draws air off the floor and circulate through the entire room keeping room cool and breezy.
Put near the windows and it helps exhaust hot indoor stuffy air and pulls in fresh outdoor air.
- Energy-saving, high velocity motor for maximum air circulation
- Tilt-adjustment for flexible use
- Triple speed selection
- Precision fan blades for powerful wind but low-noise
- Chrome-stand, solid construction with thermal-protection to prevent motor overheat.
INSTRUCTION FOR INSTALLING
WARNING: IF THE SUPPLY CORD IS DAMAGED, MUST BE REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR SIMILAR QUALIFIED PERSON IN ORDER TO AVOID THE HAZARD.
BE SURE TO SHUT OFF ELECTRIC SUPPLY AT MAIN SWITCH OR CIRCUIT BREAKER BEFORE INSTALLATION.
THE IMPORTANT SAFEGUARDS AND INSTRUCTION APPEARING IN THIS MANUAL ARE NOT MEANT TO COVER ALL POSSIBLE CONDITIONS AND SITUATION THAT MAY OCCUR.IT MUST BE UNDERSTOOD THAT COMMON SENSE, CAUTION AND CARE ARE FACTORS WHICH CANNOT BE BUILT INTO ANY PROCDUCT.THESE FACTORS MUST BE SUPPLIED BY THE PERSON(S) CARING FOR AND OPERATING THE UNIT.
NO RESPONSIBILITY WILL BE ACCEPTED FOR ANY DAMAGEWHICH MAY OCCUR DURING TRANSPORT OR BY IMPROPER INSTALLATION OR VOLTAGE FLUCTUATION OR IF ANY PORTION OF THE PRODCT HAS BEEN ALTERED OR MODIFIED.
Safety Instructions:
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- Improper installation may result in the risk of fire, electric shock, or injury to persons.
- To present risk of fire and electric shock, do not use the unit near windows.
- The fan should be placed on a flat and stable surface when operating to avoid overturning.
- The fan should not be placed in a damp place or where humidity is high (such as in a bathroom).
ASSEMBLY
Explode view
- Front Guard
- Fan Blade
- Fan Blade Screw
- Rear Guard Screw
- Rear Guard
- Motor shaft
- Oscillation Knob
- Speed Control Knob
- Motor Unit
- Power Cord Lead
text_image
1 2 3 4 5 Step 3 6 7 8 9 10 Step 2 11 12 13 14 Step 1 15- Connector Screw and Nut
- Inner Pole
- Height adjust Know
- Outer Pole
- Base
- Heavy Weight
- Fastener
- Locking Screw
- Grill Locking Screw
Fan Grill Assembly
- Fasten the rear grill onto the motor with four screws.
- Install the Blade onto the Motor Shaft by tightening the blade screw.
- Centre the Front Grill by aligning the logo on the grill Hub so it is horizontal and parallel to the floor. Then secure the Front and Rear Grills completely together by snapping grill clips into place. Lastly, tighten the grill locking screw at the bottom of the Rear Grill.
Base Assembly
- Unscrew the Fasten Ring and Base Locking Nut from the Stand Assembly.
- Insert the Stand Assembly through the hole in the center of the Base and twist into position.
- Turn the Stand Base upside down with the Stand Assembly facing the floor and place the Base Weight Support to the bottom of the Base. Tighten the Base Weight Support to the Stand Base by the fastener and locking screw.
Finally, connect the assembled fan head and stand with the connector screw and nuts, ensure it's strong enough
Operating Instructions:
a) Ensure voltage used corresponds with the voltage indicated.
b) Turn the speed control to selected speeds: 0(off) and speeds1, 2, 3 is Slow, Middle, Fast.
c) Tilting angles-By pushing the tilt-guard, you can adjust the fan to any elevation preferred.
d) Never touch the blades with hand or any object!
e) Do not pull the cord too hard. If damaged after pro-long use, get it repaired by any electrical repairman.
f) To clean: Disconnect the power cord from the mains. Remove the guard and the blades carefully. Do not drop the blades! First use soft cloth with light soap to clean off oil stains. Then wipe and polish with dry cloth. Never use polish or any corrosive liquid that will damage the paint, metal or plastic! Put back the blades and lock the guard securely before use.
NO exchange will be entertained if the above instructions are not followed. Always Test the product first before purchase.
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.