ISA1S550 - Computer accessory StarTech.com - Free user manual and instructions
Find the device manual for free ISA1S550 StarTech.com in PDF.
| Product Type | Serial Adapter Card |
| Model | ISA1S550 |
| Ports | 1 x RS-232 Serial Port (DB9 Male) |
| UART Chip | 550 UART |
| Max Baud Rate | 115.2 kbps |
| Bus Interface | ISA (Industry Standard Architecture) |
| Dimensions (L x W x H) | 120 mm x 80 mm x 20 mm |
| Weight | 150 g |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Storage Temperature | -20°C to 70°C (-4°F to 158°F) |
| Humidity | 5% to 90% (non-condensing) |
| Power Source | From ISA slot (no external power required) |
| LED Indicators | TX/RX activity LEDs |
| OS Compatibility | Windows, Linux, DOS (legacy) |
| Included Accessories | Driver CD, Quick Installation Guide |
| Maintenance | Keep dry and clean; use compressed air for dust removal |
| Safety | Install in antistatic environment; disconnect power before installation |
| Repairability | No user-serviceable parts; contact support for repairs |
| Certifications | FCC, CE |
Frequently Asked Questions - ISA1S550 StarTech.com
User questions about ISA1S550 StarTech.com
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Computer accessory in PDF format for free! Find your manual ISA1S550 - StarTech.com and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ISA1S550 by StarTech.com.
USER MANUAL ISA1S550 StarTech.com
1 Port RS-232 Serial ISA Card
2 Port RS-232 Serial ISA Card
ISA1S550
ISA2S550
Instruction Manual
natural_image
Close-up of a circuit board with multiple integrated circuits and two 24-pin connectors (no visible text or symbols)Actual product may vary from photo
StarTech.com
The Professionals' Source for Hard-to-Find Computer Parts
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Instruction Manual
Table of Contents
Introduction....1
Before You Begin ....1
System Requirements....1
Contents 1
Installation 2
Setting the Jumpers ....2
Specifications 4
Accessory Products from StarTech.com ....5
Technical Support ....6
Warranty Information ....6
Instruction Manual
Introduction
Thank you for purchasing a StarTech.com RS-232 ISA serial card. This product allows you to add between one or two serial ports to your computer (varies by model), using an easy jumper-driven configuration. An excellent choice to maximize your investment in existing serial-based technology or integrated custom solutions.
Features
- Fast data transfer rates: up to 460 Kbits/sec.
- Easy installation using a fully Plug and Play configuration
- Backed by StarTech.com's lifetime warranty and free technical support
Before You Begin
To ensure a quick and easy card installation, please read through this section carefully before attempting to install the card.
WARNING! ISA cards, like all computer equipment, can be severely damaged by static electricity. Be sure that you are properly grounded before opening your computer case or touching your ISA card. StarTech.com recommends that you wear an anti-static strap when installing any computer component. If an anti-static strap is unavailable, discharge yourself of any static electricity build-up by touching a large grounded metal surface (such as the computer case) for several seconds. Also be careful to handle the ISA card by its edges and not the gold connectors.
System Requirements
- An IBM compatible computer with an available ISA slot
Contents
This package should contain:
• 1 x ISA serial card
• 1 x Instruction Manual
Instruction Manual
Installation
This section will guide you through the installation of your ISA card and the related software. Please read through the instructions carefully and complete each step in the order listed.
Installing the Card
- Make sure that your system is unplugged and you are grounded.
- Remove the cover of your system (see your computer's user manual for details, if necessary) and gently turn your computer onto its side.
- Locate an empty ISA slot and remove the metal plate that covers the rear bracket. You may need a Phillips screwdriver to perform this step. Retain the screw! You will need it to secure the card later.
- Gently insert the card into the empty slot, making sure it is firmly seated.
- Secure the card in place using the screw you removed in Step 3.
- Put the computer case back on.
Setting the Jumpers
There are three sets of jumpers that can be configured on your card: reference transfer rate, COM address, and IRQ address.
text_image
RATE COM IRQ COM A COM BReference Transfer Rate
There are three possible transfer rate settings (labeled 1, 2, and 4) for the COM port(s). The phrase "reference" refers to the maximum possible transfer rate between the port and your device, and my not be the actual transfer speed under operational conditions. Each pin corresponds to the following transfer rate:
Instruction Manual
| Pin Rate | ||
| 1 | 1 | 15.2 Kbits/sec (defa |
| 2 | 230.4 Kbits/sec | |
| 4 | 460.8 Kbits/sec | |
Set the transfer rate for each port by setting the jumpers according to the following example:
text_image
1 2 4 1 2 4 COMA COMBIn the example above, Port A has been set to 460.8 Kbits/sec and Port B has been set to 230.4 Kbits/sec. For the single port model, you will only have the pins and jumpers to configure Port A.
COM Address
There are seven possible COM address settings (labeled 1 through 7). For the single port model, you will have a jumper to configure port A only.
-
Find an available COM Address on your system. Consult the user manual that came with your OS for instructions, if necessary. This card supports COM Addresses 1 through 7.
-
Set the COM Address for each port by placing the jumpers according to the following example:
text_image
A B 7 6 5 4 3 2 1In the example above, Port A is set to COM 1 and Port B is set to COM 2.
The base addresses are as follows:
Instruction Manual
| COM 1 3F8-3 | FF Hex |
| COM 2 2F8-2 | FF Hex |
| COM 3 3E8-3 | EF Hex |
| COM 4 2E8-2 | EF Hex |
| COM 5 2F0 | Hex |
| COM 6 3E0 | Hex |
| COM 7 2E0 | Hex |
IRQ Address
There are eight possible IRQ address settings (labeled 3, 4, 5, 9, 10, 11, 12, 15) for each port (2 port version). For the single port model, you will have a jumper to configure port A only.
- Find an available IRQ on your system. Consult the user manual that came with your OS for instructions, if necessary.
- Set the IRQ line for each port by placing the jumpers according to the following example:
In the example above, Port A is set to IRQ 4 and Port B is set to IRQ 3.
Specifications
| Interface ISA, 8-bit | |
| Ports 1 x DB-9 male (ISA1S550) | 2 x DB-9 male (ISA2S550) |
| Maxmium Data Transfer Rate 460 Kbits/sec. | |
| Configurable IRQs 3/4/5/9/10/11/12/15 | |
| Configurable COM Port Number Settings 1 | through 7 |
| Chipset Hynix GM16C550 |
Instruction Manual
Accessory Products from StarTech.com
Contact your local StarTech.com dealer or visit www.startech.com for cables or other accessories that will help you get the best performance out of your new product.
6 ft. Straight Through Serial/Parallel Cable DB25 M/F SC6MF
6 ft. Straight Through Serial/Parallel Cable DB25 M/M SC6MM
10 ft. Straight Through Serial/Parallel Cable DB25 M/F SC10MF
10 ft. Straight Through Serial/Parallel Cable DB25 F/F SC10FF
10 ft. Straight Through Serial/Parallel Cable DB25 M/F SC10MF
20 ft. Straight Through Serial/Parallel Cable DB25 M/F SC20MF
20 ft. Straight Through Serial/Parallel Cable DB25 M/M SC20MM
50 ft. Straight Through Serial/Parallel Cable DB25 M/M SC50MM
6 ft. Parallel Printer Cable PB6_
10 ft. Parallel Printer Cable PB10
20 ft. Parallel Printer Cable PC20
30 ft. Parallel Printer Cable PC30
50 ft. Parallel Printer Cable PC50
6 ft. Parallel File Transfer Cable PTXFER6
15 ft. Parallel File Transfer Cable PTXFER15
natural_image
Close-up of two white USB connectors with black leads, no visible text or symbolsInstruction Manual
Technical Support
StarTech.com's lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
Warranty Information
This product is backed by a lifetime warranty. In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
About StarTech.com
StarTech.com is "The Professionals' Source for Hard-to-Find Computer Parts". Since 1985, we have been providing IT professionals with the quality products they need to complete their solutions. We offer an unmatched selection of computer parts, cables, server management solutions and A/V products and serve a worldwide market through our locations in the United States, Canada, the United Kingdom and Taiwan.