Minx S212 - Loudspeaker CAMBRIDGE - Free user manual and instructions

Product Type	Speaker bundle (2 satellite speakers + 1 subwoofer)
Brand	Cambridge Audio
Model	Minx S212
Satellite Speaker Driver	1 x 2.25" BMR (Balanced Mode Radiator) per speaker
Subwoofer Driver	1 x 6.5" active subwoofer + 2 x 6.5" passive radiators
Satellite Frequency Response	150Hz - 20kHz
Satellite Sensitivity	86dB SPL
Satellite Impedance	8 Ohms
Recommended Amplifier Power	25 - 200 Watts per satellite
Subwoofer Power Output	200W
Subwoofer Controls	Volume, Crossover Frequency, Phase, Standby (Force On/Audio Detect)
Subwoofer Connections	AC power socket, Audio in/out (L/R line input or LFE/sub input)
Satellite Dimensions (H x W x D)	78 x 78 x 85 mm (each)
Subwoofer Dimensions (H x W x D)	219 x 210 x 222 mm
Satellite Weight	0.43 kg (0.95 lbs) each
Subwoofer Weight	5.0 kg (11.0 lbs)
Mounting Options	Wall mount (keyhole bracket included), optional pivoting wall mount, desk stand, floor stand
Cables Included	10m speaker wire, 5m RCA subwoofer lead
Additional Contents	2 x MIN12 speakers, 1 x X201 subwoofer, safety guide, quick start guide
Power Supply	AC mains (subwoofer)

Frequently Asked Questions - Minx S212 CAMBRIDGE

What is speaker sensitivity?

Speaker sensitivity is the sound pressure level (SPL) produced by the speaker at one meter when supplied with one watt of power. It indicates how efficiently the speaker converts power into volume. Typically measured in dB, a higher sensitivity (e.g., 90dB) means louder output than a lower sensitivity (e.g., 87dB). Every 3dB increase represents a doubling of perceived loudness.

What is a crossover and why is it important?

A crossover is an electronic circuit that splits the audio signal into different frequency bands for different drivers (e.g., tweeter, midrange, woofer). This ensures each driver handles only the frequencies it is designed for, resulting in clearer, more accurate sound reproduction.

What is impedance and how does it affect my system?

Impedance (measured in Ohms) is the electrical load a speaker presents to an amplifier. Lower impedance (e.g., 4Ω) requires more current and can cause an amplifier to overheat if it cannot supply the necessary power. Always match speaker impedance to your amplifier's rated range.

Why is there no sound from one or both satellite speakers?

Check that the amplifier is turned on and the correct input source is selected. Ensure all connections (speaker wire to amplifier and speakers) are secure and polarity is correct. Verify the volume control is not turned down.

What should I do if the sound is distorted or inconsistent?

Confirm all connections are secure. Check speaker wire polarity (red to red, black to black). Ensure connections from source equipment to amplifier are also secure. If using a subwoofer, adjust the crossover and volume settings.

Why is there no sound from the subwoofer?

Ensure the amplifier and subwoofer are both turned on. Verify the correct input source is selected. Check that the subwoofer volume and crossover controls are set appropriately. Ensure the subwoofer cable is securely connected. If using an AV receiver, confirm the subwoofer output is enabled.

The subwoofer has no power. What could be wrong?

Confirm the subwoofer's AC power cable is securely connected to both the subwoofer and a wall outlet. Make sure the power switch on the subwoofer is in the 'On' position. Check that the wall outlet is switched on and working.

Can I mount the MIN12 speakers on a wall?

Yes, the MIN12 speakers include a keyhole bracket for simple wall mounting. Additionally, optional accessories like a pivoting wall mount, desk stand, or floor stand are available for flexible placement.

How should I position the subwoofer for best performance?

Low-frequency sound is largely omnidirectional, so you can experiment with placement. Typically, placing the subwoofer in a corner or along a wall can enhance bass output. Try different positions and listen for the best balance.

What maintenance is required for the Minx S212 speakers?

The speakers require minimal maintenance. Dust the enclosures with a soft, dry cloth. Avoid using any abrasive cleaners or liquids. Ensure ventilation openings are not blocked. Periodically check connections for security.

USER MANUAL Minx S212 CAMBRIDGE

Minx S212 Speaker Bundle

Manual Generated: 15/02/2023 - 00:58

Table of Contents

Minx S212 Speaker Bundle 3

Introduction 4

What's included with the Minx S212 bundle? 5

Minx MIN12 front and rear 6

Minx X201 front and rear 7

Minx MIN12 installation 9

Minx X201 unboxing and installation 10

Technical specifications 12

Frequently asked questions 13

Troubleshooting 14

Minx S212 Speaker Bundle

Last updated: February 7, 2023 04:00. Revision #8863

Users Manual

Introduction

Last updated: February 2, 2023 04:44. Revision #8812

Thank you for purchasing this Cambridge Audio Minx Minx S212 loudspeaker bundle. We hope that you enjoy many years of listening pleasure from it. Your loudspeakers can only be as good as the system it is connected to. Please do not compromise on your amplifier. Naturally we particularly recommend amplification from the Cambridge Audio range, which has been designed to the same exacting standards as our loudspeakers.

Thank you for taking the time to read this manual; we do recommend you keep it for future reference.

© Copyright Cambridge Audio Ltd.

For upcoming news on future products, software updates and exclusive offers, make sure you register your product at

http://www.cambridgeaudio.com/register

What's included with the Minx S212 bundle?

Last updated: February 9, 2023 08:34. Revision #8870

1. 2 x Minx MIN12 compact speaker.
2. Minx X201 subwoofer.
3. Safety guide.
4. Quick start guide.
5. 10m speaker wire.
6. 5m RCA subwoofer lead.

Minx MIN12 front and rear

Last updated: February 2, 2023 04:44. Revision #8814

Front.

1. 2.25" BMR Driver.

Rear panel.

1. Mounting Screw Thread.
2. +/- Speaker Connection Terminals.

Minx X201 front and rear

Last updated: February 2, 2023 04:44. Revision #8815

Front.

1. 6.5" Subwoofer.

Rear Panel.

1. AC power socket.
2. Mains power switch - Switch the subwoofer between on and off.

3. Standby switch - Switch between 'Force On' (no standby), and 'Audio Detect'. In audio detect mode the X201 will switch on when it detects an incoming signal.

4. Crossover frequency control - Adjust the crossover frequency of the subwoofer.

5. Phase control - Adjust the phase settings of the subwoofer.
6. Volume control - Adjust the volume of the subwoofer.
7. Audio in/out.

Minx MIN12 installation

Last updated: February 2, 2023 04:44. Revision #8816

1. Firstly, ensuring to match the polarity/colour coding, connect the supplied speaker terminals to the speaker outputs of your amplifier by unscrewing the ends, and securing the speaker cable in the available hole on each terminal. These terminals can then be installed into the rear of the MIN12 with the cables connected.

1. If mounting the MIN12 speakers to a wall you will need to attach the included keyhole bracket using the mounting screw to the rear of the speaker.

1. Alternatively, we offer several other mounting solutions including a pivoting wall mount, desk stand, and floor stand.

Minx X201 unboxing and installation

Last updated: February 2, 2023 04:45. Revision #8817

Unboxing your Minx X201 subwoofer.

Follow the diagram and take care when unboxing your Minx X201 so not to damage the speaker cone.

Installation of your Minx X201.

Dependent on your desired setup, there are a few different ways to connect your Minx X201 subwoofer.

1. If you are using an amplifier with a L+R pre-out then use the left and right line input connections to connect your Minx X201.

1. If you are using a receiver, or amplifier with a dedicated sub out then connect the Minx X201 using the left channel (LFE/Sub) input.

1. Once connected you can decide where to position your subwoofer. As low frequency content is largely unidirectional, you can experiment to find a place that suits your setup.

Technical specifications

Last updated: February 2, 2023 04:45. Revision #8818

Minx MIN12.

Sensitivity (SPL)

86dB

Frequency Response

150Hz - 20kHz

Impedance

8 Ohms

Drivers

1 x 2.25" BMR Driver

Recommended Amplifier Power

25 - 200 Watts

Speaker Dimensions (H x W x D)

78 x 78 x 85mm.

Weight

0.43kg (0.95lbs)

Minx X201.

Power output

200W

Drivers

1 x 6.5" subwoofer

2 x 6.5" passive radiators

Speaker dimensions (H x W x D)

219 × 210 × 222mm

Weight

5.0kg (11.0lbs)

Frequently asked questions

Last updated: February 2, 2023 04:45. Revision #8819

What is meant by speaker sensitivity?

Speaker sensitivity is the level produced by the speaker at one meter, when supplied with one watt of power from an amplifier. It's a way of describing how well the speaker produces acoustic energy, based on a given input. The level is measured in dB SPL – this shorthand for 'sound pressure level' – sound is basically fluctuations in air pressure, so any time you see SPL, this means 'sound in the real world'. So, let's say we have a speaker with an 87dB sensitivity, and a speaker with a 90dB sensitivity – the 90dB speaker is going to be considerably louder, as every 3dB added represents a doubling of power.

What is a crossover?

Most speakers will have multiple drivers. A driver is sometimes called a transducer, which is a device that turns one type of energy into another – in this case, electrical energy to sound energy. In a loudspeaker, it is often the case that we might want multiple drivers – one to handle low-end, one to handle the mid-range, and one to handle the treble. This latter driver is often called a tweeter. To get the benefit of this arrangement, we need to split the signal into different frequency components. The circuit that does this is called a crossover.

What is impedance?

You will often see impedance mentioned when researching speakers, and amplifiers. Impedance is basically resistance measured at a given frequency, given as a value in Ohms ( Ω ), and is incredibly important to consider when setting up an audio system as it determines the 'load' placed on an amplifier by the speakers.

For example, let's say we have an amplifier that is rated to deliver 100W into an 8Ω speaker load. If we were to then use speakers with an impedance of 4Ω with the same amplifier, the amp would then need to supply 200W as a halving of the impedance results in a doubling of the required power due to the reduction of the load on the amplifier.

In a situation such as this, if the amp can't supply the required power for a lower impedance, then it can result in overheating, and damage to the amplifier and speakers.

For this reason, it is important to pay attention to amplifier specifications, and suggested impedance ratings.

Troubleshooting

Last updated: February 2, 2023 04:45. Revision #8820

No sound through one or both channels.

• Check that the amplifier is turned on.
• Ensure that the correct input source is selected on the amplifier.
• Confirm that all connections between the amplifier and loudspeakers are secure.
• Check that the connections between the source equipment and amplifier are secure.
• Check the polarity of the loudspeaker connections.
• Check that the volume control is set correctly on the amplifier.

There is distorted or inconsistent sound.

• Confirm that all connections between the amplifier and loudspeakers are secure.
• Check the polarity of the loudspeaker connections.
• Check that the connections between the source equipment and amplifier are secure.

No sound through subwoofer.

• Check that the amplifier is turned on.
• Ensure that the correct input source is selected on the amplifier.
• Check that the subwoofer is turned on.
• Confirm that all connections between the amplifier and subwoofer are secure.
• Check that the connections between the source equipment and amplifier are secure.
• Check that the volume control is set correctly on the amplifier.
• Check that the volume control is set correctly on the subwoofer.

There is no power to the subwoofer.

• Confirm that the connection to the mains is secure.
• Confirm that the plug is switched on at the wall.