V5B1M - Camera Speco Technologies - Free user manual and instructions

Product Type	Security Camera
Model	V5B1M
Brand	Speco Technologies
Image Sensor	1/2.5" CMOS 5MP
Resolution	5MP (2560 x 1944)
Video Output	AHD/TVI/CVI/CVBS (default HD-TVI)
Image System	PAL/NTSC
Electronic Shutter	Auto, 1/50~1/100000 (PAL), 1/60~1/100000 (NTSC)
Minimum Illumination	Color: 0.011 lux @ F1.2, AGC ON; 0 lux with IR
IR Distance	98.4 - 164.0 ft (30 - 50 m)
Lens	2.5 - 12mm varifocal
Lens Mount	D14
S/N Ratio	≥33 dB (AGC OFF)
Ingress Protection	IP67
Power Supply	DC12V (±10%)
Power Consumption	IR OFF < 1W, IR ON < 4W
Operating Temperature	-22°F to 122°F (-30°C to 50°C)
Dimensions (W x H x D)	8.6 x 3.3 x 3.35 inches
Control Method	OSD via UTC
Special Features	WDR, BLC, DNR, AGC, White Balance, Smart IR, Mirror, Sharpness, Defect Correction

Frequently Asked Questions - V5B1M Speco Technologies

How do I install the V5B1M camera?

Make sure the wall or ceiling can support the camera weight. Use the drill template to mark screw and cable holes. Route and connect cables, then secure the mounting base with screws. Adjust the camera angle by loosening the fixed ring, previewing the image on a monitor, and tightening the ring after adjustment.

What video output modes are supported?

The camera supports four video output modes: AHD, TVI, CVI, and CVBS. It comes defaulted to HD-TVI.

How do I switch the video output mode?

Remove the cover of the video switch cable, then press and hold the button inside for 5 seconds to cycle through the modes: AHD, TVI, CVI, and CVBS.

What is the IR distance of this camera?

The V5B1M has an IR distance of 98.4 to 164.0 feet (30 to 50 meters), allowing clear night vision.

How do I adjust the camera angle?

For the V5B1M, loosen the fixed ring, adjust the camera to the desired view angle while previewing on a monitor, then tighten the fixed ring to secure the position.

Can the camera be used outdoors?

Yes, the V5B1M has an IP67 ingress protection rating, meaning it is dust-tight and can withstand temporary immersion in water. It is suitable for outdoor use in dry environments.

What is WDR and how does it help?

Wide Dynamic Range (WDR) balances bright and dark areas in a scene, providing clear images when both very bright and very dark areas are present simultaneously.

How do I access the OSD menu?

The OSD (On-Screen Display) menu can be accessed via UTC (Up-the-Coax) control. Use a compatible DVR or monitor with UTC support to navigate the camera's settings.

What power supply is required?

The camera requires a DC12V power supply with a tolerance of ±10%. Ensure the power supply voltage is correct before use.

How do I clean the camera lens?

Keep the camera away from liquids. Use a soft, dry cloth to gently clean the lens. Do not use harsh chemicals or solvents. Avoid touching the lens directly with fingers.

USER MANUAL V5B1M Speco Technologies

Collection of white surveillance cameras with lens and camera modules (no visible text or labels)

V/V5T1// 5B1 V5D1 V5B1M/V5D1M/V5T1M

USER MANUAL

Thank you for purchasing our product. Space Technologies is currently developing and improving products. We reserve the right to modify product design and specifications without notice and without mounting any obligation.

Warnings

■ If the product does not work properly, please contact the dealer or where the product was purchased
Spatco Technologies is not responsible for any problems caused by improper operation or repair.
- Keep away from liquid while in use.
All installation and operation here should conform to local electrical safety codes.
■ Make sure the power supply voltage is correct before using the camera.
■ Do not drop the camera or subject to physical shock
■ Do not use the device beyond specified voltage range.
■ Do not place the camera in extremely hot, told the opening temperature shall be (-1 F - 122°F), dusty or
damp locations, and do not expose it to high electromagnetic radiation
■ Toroidal heat accumulation, pool certification is required for operating environment

Introduction

This camera series is the latest technology and advanced circuit design, which features high definition and

sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable.

ecouring the requirement of the H2 monitoring in the additional surveillance system.

High Resolution

Adapt high performance sensor, providing high definition and clear image.

● High Transmission Performance

Real-time transmission with high speed and long distance.

DNR

Reduce noise from brightness and color signal.

OSD

Assess the camera settings which can be clearly displayed through the main menu.

● White Balance

Adjust the zolar temperature according to the environment automatically.

ICR Auto Switch

The filter will filter infrared light during the daytime and change to normal night to

ensure a high sensitivity and clear image.

AGC

Adjust the gain of amplifier, enabling the camera to output the standard video signal in different

ghting condition.

● Wide Dynamic Range (WDR)

When there are both very bright and very dark ones simultaneously in the field of view, this function

will balance the brightness level and provide clear images.

● Backlight Compensation (RLC)

What the back of the captured object is too much, bright, you can set BLC for the captured object to

make it clearer.

Cables

Video Switch: Four video output modes can be essential. All[D, TV], CVI and CVBS tail remove the cover of the video switch cable; (b) hold and press the button in the video switch cable for 5 seconds to switch the current video output.

Installation

Before you start, please make sure that the wall or ceiling is at long enough to withstand the time to the weight in the camera. Please install and use the camera in the dry environment. You can better install back the lens cover or lower dome less than 4 hours after removing it. The mounting types of cameras are only for reference.

▶Mounting for V5B1/V5T1

1. Drill the screw holes and the axle hole on the wall recurring to the drill template.

1. Route and connect the cables.
2. Secure the mounting base with corners to the wall with surfaces as shown below.

V5B1

VSBIM

1. Bracket adjustment. Before adjustment, preview the image of the camera on a monitor and then loosen the fixed ring to adjust the view angle of the camera. Tighten the fixed ring after the adjustment.

V5BI

V5RIM

▶Mounting for Dome Camera

● Mounting for V5D1/V5D1M

1. Attach the drill template to the place where you want to fix the camera and then drill the screw holes, and the cable hole on the wall according to the drill template.

V5D1

VSDIM

1. Rotate the trim ring anticlockwise to remove it from the camera.
2. Leaven the surveys to open the lower done. Then made and connected the cables.
3. Square the camera to the wall with screws pro-idal at crown below.

1. Tires-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then adjust the camera according to the figure below to get an optimum angle.

1. Install the lower come back to the camera and fix it with screws. Then put the trim ring onto the lower dome and then rotate a clockwise until it is locked. Finally, remove the protection film suit.

● Mounting for V5T1/V5T1M

1. Drill the screw holes and the cable hook on the wall according to the drill template.

1. Does not be fixed screw to disassemble the camera.
2. Route and connect the cables. Then secure the mounting base to the ceiling or wall with the screws provided.

1. Install the door and enclosure to the mounting base and then adjust the door to deform an optimum view angle. Finally, secure the camera with the fixed screw.

Specifications

Specifications\Models	VSB1	VSBIM	VSD1
Camera
Image Sensor	10.2"CM 5"
Resolution	5MP
Image size	2560×95
Video Output	AHXTV14-V3/CNBS (Panaroscopic details to HD-TVI)
Image System	PAL/NISC
Electronic Stometer	Auto, 1.5X~1.1000GxPAL,1.5X~1.5000Gb(N1SC)
IR Distance (dB)	65.6-98.4	98.4-164.0	65.6-98.4
Frame Rate	20fps
Min. Illumination	Culse: 0.011lux@F1.2, AGC ON, BL/W; 0lux with IR
Lens	2.8mm	2.5-12mm (multicell)	2.8mm
Lens Mount	M12	D14	M12
S/N Ratio	≥33dB(ASC OFF)
Ingress Protection	IP67	IP67	IP67&IK10
Functions
Function Control	OSD (UTC control)
Day dNight	ICR
WDR	Yes
Digital NR	Yes
AGC	Yes
Ave White Balance	Yes
Debug	No
BLC	Yes
LSC	Yes
Mirror	Yes
Sharpness	Yes
Smart IR	Yes
Image Rating	Yes
Defect Correction	Auto
Others
Power Supply	DC12V (± 10%)
Power Consumption	IR ON < 1W; IR ON < 4W		IR OFF < 1W; IR ON < 4W
Working Environment	22.9°F ~ 122.9°F, 10% ~ 90%(relative humidity)
Dimensions (inch)	5.6 2.9 2.95 x	8.6 3.3 3.35 x	94.7 3.5x
Specifications\Models	VSDIM	VSTI	VSTM
Camera
Image Sensor	1-2.5" CM 9
Resolution	5MP
Image size	2500×1906
Video Output	AHV/FV3/CV/CVBS (camera comes defaulted to HD-FV)
Image System	PAL/NTSC
Electronic Shutter	Auto, 155G=1-100000(PAL),10Hz=3/10000ns (NTSC)
IR Distance (kHz)	68.4~114.0	65.6~95.4	90.4~104.0
Frame Rate	76fps
Min. Illumination	Color=0.0 (Hz)×FL1.2 AGC ON: R/W; GHz with IR
Lens	2.8~4.0 (mm/s/μF)	2.8nm	2.5~12nm (footer/shell)
Lens Mount	D1.1	MDZ
SN Range	8320dB (AGC OFF)
Ingress Protection	IP6 08K10	IPn7	IPs7
Functions
Function Control	OSD (UPC control)
Day dNight	JCR
WOR	Yes
Digital NR	Yes
AGC	Yes
Auto White Balance	Yes
Defing	Nt
R1C	Yes
LSC	Yes
Mirror	Yes
Sharpness	Yes
Smart IR	Yes
Image Setting	Yes
Defence Correction	Auto
Others
Power Supply	DC(2V ± 10%)
Power Consumption	IR ON < 1W; IR ON < 6W	IR ON < 1W; IR ON < 4W	IR ON < 1W; IR ON < 6W
Working Environment	-22 °F = -122 °F, 10 % - 9 % (negative humidity)
Dimensions (inches)	Φ5.6 5X±	Φ5.7 3.5±	Φ5.4 3.5±

Model: V5B1/V5B1M/V5D1/V5D1M/V5T1/V5T1M

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

FCC Responsible Party:

Speco Technologies

200 New Highway

Amityville, NY 11701

www.specotech.com