H2LB1 - Camera Speco Technologies - Free user manual and instructions

Product Type	Surveillance Camera
Brand	Speco Technologies
Model	H2LB1
Image Sensor	1/2.8" CMOS, 2MP (1920x1080)
Lens	2.5mm fixed lens, M12 mount
Video Output	AHD, TVI, CVI, CVBS (switchable)
Power Supply	DC 12V ±15%
Power Consumption	IR Off: <1W; IR On: <3W
Operating Temperature	-22°F to 122°F
Operating Humidity	10% to 90% non-condensing
Minimum Illumination	0 lux (with IR on)
Electronic Shutter	Auto, 1/20s to 1/10000s (PAL), 1/50s to 1/10000s (NTSC)
Day/Night	Yes, with smart LED (manual or auto mode)
Features	HD resolution, DNR, OSD menu, White Balance, AGC, BLC, Digital WDR, Sharpness, Color Gain
Video Frame Rate	Up to 30fps@1080p (NTSC) / 25fps@1080p (PAL)
Mounting	Wall or ceiling mount with included bracket
Dimensions (H2LB1)	Approx. 0.52 x 3.71 x 3.7 inches (1.3 x 9.4 x 9.4 cm)
Weight	Not specified, typically ~0.5 lb
Warranty	Contact dealer for warranty details

Frequently Asked Questions - H2LB1 Speco Technologies

How do I switch the video output mode on the H2LB1 camera?

Remove the cover of the video switch cable, then press and hold the button inside for 5 seconds to cycle through AHD, TVI, CVI, and CVBS modes. The current mode is indicated by the camera's OSD or monitor display.

What is the maximum distance for video transmission?

The camera supports real-time transmission over long distances via coaxial cable. For typical HD-TVI/CVI signals, distances up to 500m (1640ft) are achievable with proper cable quality.

How do I adjust the viewing angle of the H2LB1?

Mount the camera loosely, then preview the image on a monitor. Loosen the fixed ring to adjust the angle, and tighten it once the desired view is obtained. The H2LB1 has a fixed lens so only physical adjustment is possible.

Does the H2LB1 support OSD (On-Screen Display) menu configuration?

Yes, the camera supports OSD menu via UTC control. You can access settings such as DNR, white balance, AGC, BLC, and more using a compatible DVR or tester.

What is the night vision range of the H2LB1?

The camera uses infrared LEDs with a typical range of up to 30-50 feet (10-15m) in total darkness. Actual range depends on scene reflectivity and ambient light.

How do I clean the camera lens?

Use a soft, dry cloth to gently wipe the lens. Avoid using abrasive cleaners or liquids. For stubborn dirt, slightly dampen the cloth with a mild lens cleaner or distilled water.

Can I use the H2LB1 with a 24V AC power supply?

No, the camera requires a regulated DC 12V power supply (±15%). Using a different voltage may damage the camera.

What is the purpose of the DNR (Digital Noise Reduction) feature?

DNR reduces noise in the video signal from both brightness and color information, resulting in a cleaner and sharper image, especially in low-light conditions.

How do I reset the camera to factory settings?

There is no dedicated reset button. You can restore defaults via the OSD menu if accessible, or contact technical support for assistance.

Is the H2LB1 weatherproof?

The camera is designed for indoor or sheltered outdoor use. It is not rated for direct exposure to rain or dust. The manual recommends installation in a dry environment.

USER MANUAL H2LB1 Speco Technologies

Three white surveillance cameras with digital displays and a small cylindrical component (no visible text or symbols)

H2LT1/H2LB1

User Manual

Thank you for purchasing our product. Speech Technologies is community developing and improving products. We reserve the right to modify product design and specifications without notice and without imposing any obligation.

Warnings

■ If the product does not work properly, please contact the dealer or where the product was purchased
Spatco Technologies is not responsible for any problems caused by improper operation or repair.
- Keep away from liquid while in use
■ All installation and operation here should conform to local electrical safety codes.
■ Make sure the power supply voltage is correct before using the camera.
■ Do not drop the camera or subject to physical shock
■ Do not use the device beyond specified voltage range.
■ Do not plan the camera in extremely hot, sold the opening temperature shall be (-22°F - 122°F), dusty or
damp locations, and do not expose it to high electromagnetic radiation
■ Toroidal heat accumulation, pool certification is required for operating environment

Introduction

This camera series is the latest technology and advanced circuit design, which features high definition and

sensitivity, low noise and distortion and supports HD video transmission with the common central cable.

ecouring the requirement of the H2 monitoring in the additional surveillance system.

High Resolution

Adopt high performance sensor, providing high definition and clear image.

● High Transmission Performance

Real-time transmission with high speed and long distance.

● DNR

Reduce noise from brightness and color signal.

OSD

Access the camera settings which can be clearly displayed through the main menu.

● White Balance

Adjust the zule temperature according to the environment automatically

● AGC

Adjust the gain of amplifier, enabling the camera to output the standard video signal in different

lighting condition.

● Backlight Compensation (BLC)

When the back of the captured object is too much bright, you can set BLC for the captured object to

make it clearer.

Cables

Video Switch: Four video output modes can be open. ADHD, TVI, CVI and CVBS (a) remove the cover of the video switch cable; (b) hold and press the button in the Video switch cable for 5 seconds to switch the current video output.

Installation

Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera. Please install and use the camera in the dry environment. You'd better install back the lens cover or lower come less than 4 hours after removing it. The mounting types of cameras are only for reference.

▶Mounting for H2LB1

1. Drill the screw holes and the cable hole on the wall according to the drill template.

1. Route and connect the cables.
2. Secure the mounting base with connection to the wall with screws as shown below.

1. Bracket adjustment. Before adjustment, preview the image of the camera on a monster and then zoomed the fixed ring to adjust the view angle of the camera. Tighten the fixal ring after the adjustment.

▶ Mounting for H2LT1

1. Attach the drill template to the phase where you want to fix the room and then drill the screw hokes and the cable hole on the wall recovering to the drill template.

1. Listen the fixed screw to disattracting the camera

1. Secure the mounting base to the ceiling or wall with the screws

prudidal.

1. install the dose and enclosure to the mounting base.

Technical line drawing of a surveillance camera with top and side views (no text or symbols)

Then adjust the dome to obtain an optimum view angle.

1. Finally, fix the camera with the fixed screw.

Specifications

Specifications\Models	1011R1	1011T1
Cancem
Image Sensor	1/2.8" CM 3D
Resolution	26MP
Image size	1920x-1000
Video Output	ADD/TVCV/VCVBS (current counts defaulted to H2-I VII)
Image system	PAL-NTSC
Electronic Statter	Auto, 1/20Hz~1/10000A(PAL), 1/50Hz~1/10000A, (NTSC)
IR Distortion (dB)	16.98
Fuse Rate	10fps(90Hz); 25fps(50Hz)
Max. Illumination	0lux(.FF) ON)
Lens	2.5 mm
Lens Mount	M/2
SN Ratiu	±Shift(A/C 0.07)
Ingress Protection	DW2
Emotions
Emotion Control	DSD (UTC control)
Smart LED	Manual or auto mode
B-DR	Digital WDR
Digital NQ	Yes
AGC	No
Auto White Balance	Yes
Debug	No
BLC	Yes
Contact	Yes
Saturn-on Color Gain	Yes
Sharpness	Yes
Exposure	Global exposure or general exposure supported
Impug. Setting	Yes
Discret Generation	Anti
Others
Power Supply	DC12V (± 15%d)
Power Consumption	IR OUT < ± 1W; IR ON < ± 3W
Working Environment	-22 °F ~ -122 °F, 10 °F ~ 90 °F (elective humidity)
Dimensions (inch)	0.52 3.71 × 3.7	40.72 3.25×

Model: H2LT1/H2LB1

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

This device must accept any interference received, including interference that may

cause undesired operation.

FCC Responsible Party:

Specn Technologies

200 New Highway

Amylyville, NY 11701

www.specotech.com