MD-BD13B - Aide à la marche Gabor - Free user manual and instructions

USER MANUAL MD-BD13B Gabor

For 13"-27"(33-69 cm) LCD desktop computer monitors

User Manual

Thank you for choosing Gabor.

The Gabor MD-BD13B mounts two 13"-27" (33-69 cm) LCD computer monitors side by side. It attaches to the edge of your desk via a built-in clamp, freeing up valuable desk space and enabling personalized monitor placement for improved safety and comfort over conventional monitor stands. This desktop mount incorporates two dual-segment arms with multiple points of articulation to provide a full range of motion, making it easy to adjust your monitors' horizontal position, tilt, swivel, and roll.

2 Welcome

Office desk setup with a black adjustable arm mounted on a stand, person working at the desk (no visible text or symbols)

Overview Snott box Locking contact Latchet handle Coat. Close Close locking knob Overview Mounting Arms VPGA Monial Hexo press Locking Anos Small Cable clips Cable clips Mounting clips Tools Required For Installation • Phillips Screwdriver

Also included

Supplied Parts & Hardware

A (B) M×12 screws	D (B) V5×30 screws	G Short Cup
B (B) V4×30 screws	E 4 mm hex key	H User Monus
C (B) V5×12 screws	F (B) Spacers

M4 MS Hex Key Spacers 6 x8 7 x9 8 x8 E x4 F x3 G x2 C (cyclohexane/0)

Overview

Product Specifications

Monitor display size

13-27(33-69cm)

Maximum load capacity (per cm)

12.615 (Hg)

VESA standards 75·75 100·100

Tilt ±15

5Mwcl 180

B. (1) 2023

that: 360

Installation: Clamp hits down edges up to 2015 cm thick

24-100%

Arm width (extended): 31.5' (80 cm)

Spector dimensions

Lunch: 16.5 mm

Dukes dimmeters: 15 mm

Bark Dunlopel 25mm

Inner diameter: 5.5 mm

Height: 25.67 (58 cm)

Weight 7.5 lb.13.4 kg

360°360° 350° 180° 160° +15° 360° +15°

Safety Warnings

Please read and follow these instructions

and keep the manual man's space.

Eleum, his product with dry tea soft, dry cloth.

Keep this product away from children.

Make an easy thing to get before proceeding.

Meas surprised this product's intact one

that there are no missing parts.

do avoid damage to this product, be careful not to overtighten or improperly thread any of the threaded fittings.

Do not exceed the maximum load capacity.

Do not install this product or on unsteady structure or one that is prone to vibration, but a chance of being impacted, or is susceptible to other movements. Reinforce the structure as necessary before installing this product.

Mounting surfaces should be sturdy and flot. Do not install this product on a week, uneven surface.

The following are the following purpose, only.

Getting Started

Decide where you want to place your monitors. When using a duch-monitor setup like this one, post on your primary monitor directly in front of you, and your secondary monitor to the side. You shouldn't need to turn your head to look at your primary monitor. Both monitors should be at eye level, approximately at an arm's length away. If you have to screen to look at either monitor, there is its position.

Attaching the Shaft

The MD-B13B easily attaches to most desks in to P/A (5 cm) thick. Before attaching the shelf to your desk, make sure you have enough room to fit the entire clamp behind your desk. To attach the shelf to your desk, follow these steps!

1. Locser the clamp locking knob until you can fit the clamp over the edge of your desk.

2. Fit the clamp over the edge of your desk, one tighten the clamp locking knob until the scuff is securely mounted to your desk.

Installati

Attaching Your Monitor to the VESA Mounts:

Before allocating your monitor to the VEA monitor, you may need to detach your monitor's built-in stand. For information on how to do this, consult your monitor's user manual.

Depending on how the bank of your monitor is configured, you can use one of two methods to install the VISA mount onto your monitor flush or recessed. If your monitor's VISA mounting hoies are flush with the rest of the monitor, use the Flush installation instructions on the next page. If your monitor's VISA mounting holes are the recessed errors of the monitor, use the Recessed Installation instructions on page 12.

10 installation instructions

Flush Installation

Note: Before starting, make sure the VSSA mount, mounting arm, one monitor are focusing the proper direction.

1. Carefully place your monitor frontdown on a flat surface.

Tips: To avoid scratching the screen, place your monitor on a soft cloth such as a towel.

1. Align the mounting holes in the VESA mount with the corresponding mounting holes in your monitor.

2. Depending on your monitor's throw size, insert four of the included M4×2 or M5×12 screws into the VESA mount and use a Phillips-head screwdriver to fasten them until fully tightened.

Report these or the other set of installation steps as necessary for your second monitor and continue to Attach the Mounting Arm Assembly on behalf.

11 installati

Recessed Installation

Note: Before starting, make sure the VSSA mount, mounting arm, one monitor are focusing the proper direction.

1. Carefully place your monitor frontdown on a flat surface.

Tips: To avoid scratching the screen, please your monitor on a soft cloth such as a towel.

1. Place four of the included spaters on each of your monitor's four VESA mounting holes.

2. A sign the mounting holes in the VESA mount with the four spaters.

3. Depending on your monitor's thread size, incl. four of the included M4x30 or M5x30 screws into the VESA mount and use a Phillips-head screwdriver to fasten them until fully tightened.

Tip: Thread each of the screws by hard before fostering them with the screwdriver.

Repeat these of the other set of installation steps as necessary for your second monitor, and continue to Attaching the Mounting Arm Assembly on the next page.

12 Installation Instructions

Attaching the Mounting Arm Assembly

1. Onset the locking collar by rotating the ratchet handle, and then slide the collar onto the shelf.

2. Slice the looking collar to the height of which you want to mount your monitors, and then tighten the ratchet handle to lock the collar in place.

3. Slide the mounting arm assembly, with monitors attached, onto the shaft so it rests on the locking collar, and then fully tighten the locking knot until secure.

4. Insert the protective cap into the top of the shaft.

5. Thread your monitor cables through the cab e clips.

13installot

Adjusting Tension and Articulation

Arm Positioning

Both arms have two joats apiere, moving it easy to adjust your monitors' horizontal placement. Position the arms as desired and use the included 4 mm hex key to foster the hex screws until fully tightened.

Monitor Tilt, Swivel, and Roll

You can adjust the [vertical] tilt and [horizontal] swivel action of your monitors for optimal viewing comfort. You can also roll, or rotate, your monitors 300° for portrait or scope orientation or anything in between.

14 Installation instructions

Customer

Support

For more information or to arrange service, visit www.madebygabor.com or call Customer Service at F12-574-2358.

GABOR™ A Graske Group Brand

Product security is provided by the Grudus Group. www.grudusgroup.com

Subor is registered vendors of the Cervus Group.

©2014 Croclus Group LLC. All Rights Reserved.

ONE YEAR LIMITED WARRANTY

This CAD/OP product is canonical to the given producer, but the free reference in this material is likely to be a certain one or more used in the first part of this year. They are not only possible that the 40% other experience, however, there's later. The warranty product's positivity with respect to this limited warranty shall be indicated solely to require replacement, at the analyst's discretion, or any product that falls during the period of the product in its intended management in its intended environment, except by the product on partial and equal determined by the warranty provider. If the product has been discontinued, we may consider price reserves the right to estimate it, within model of equivalent quality and "not an

This warranty does not use damage or claim any loss, impact, expense, amortization, sale, property, resale price or other income. This is held in HHS, the warranty profile is made by the EXPIRES WARRANTIES for any implied warranties billable. But this warranty is not to be made from any of the provisions that are subject to purchase or sell any securities or futures. For any particular purpose, it may not be sold or sold directly, and you may also have additional rights that only form a stock as follows: To obtain any underlying amount, until it is delayed to receive Service Experiences to retain a return on deposit or a combination ("GS") number, one value is negative; however, no further purchase or sell any securities or futures. Suppose the respective product in the currency's own risk and security.

Close-up of a wooden surface with parallel grooves and concentric rings, no text or symbols visible.