GR-U932SSDM - Fridge LG - Free user manual and instructions

USER MANUAL GR-U932SSDM LG

Please read this manual carefully before operating your set and retain it for future reference.

Model Name

LT20CBBVIN

LT24CBBVLN

LT24CBBWLN

GR-U932SSDM

GM-U792SSXM

GM-U552SSDM

AFN75754510

P/No. MFL67527907-12

LT24CBBVLH

LT24CBBWLH

LT20CBBWIN

TABLE OF CONTENTS

Important Safety Instructions 2-3 Refrigerator Care and Cleaning 16-17

Requirements for Ground Connection 3 Refrigerator Cleaning 16

Outside 16

Inside 16

Parts and Features 4 Door Lining & Gaskets 16

Door Lining & Gaskets 16

Plastic Parts (Covers and Panel) 16

Back Cover 16

Refrigerator Installation 5-11 Replacing Refrigerator Lights 16

Unpacking 5 Power Interruptions 16

Installation 5 When Going on Vacation 16

How to remove and Install the When Moving 17

Refrigerator Doors 6-7 Smart Functions 17

How to reverse and Install the Door Alarm 17

Refrigerator Doors 8-11

Closing and Aligning the doors 11

Troubleshooting Guide 18-22

Using your Refrigerator 12-15

Ensuring Proper Air Circulation 12 Specifications 22

Adjusting the Controls 12

Adjusting Control Settings 13

Food Storage Guide 13

Refrigerator Shelves 14

Pantry Drawer 14

Ice Tray 15

Humidity Controlled Crispers 15

Door Bins 15

Dairy Bin 15

IMPORTANT SAFETY INSTRUCTIONS

SAFETY MESSAGES

This manual contains several important safety notices. Always read and obey all of the following safety messages.

This is the safety alert symbol. This symbol is a warning to potential dangers that could cause death, injury or damage to you, others or the product. All safety messages will follow after this warning symbol and the word "DANGER", "CAUTION" or "WARNING". These words mean:

DANGER

WARNING

CAUTION

You may be killed or suffer fatal damage if you do not follow instructions.

You may be killed or seriously injured if you do not follow instructions.

Indicates a potentially hazardous situation which, if not avoided, may result in minor injury or damage to the product.

All safety messages inform you of potential danger, advise you on how to reduce the risk of injury and tell you what can occur if the instructions are not followed.

WARNING

To reduce the risk of fire, electrical shock or personal injury, the following precaution measures should be followed:

• NEVER disconnect the refrigerator by pulling the power cord, always grip the plug firmly and disconnect it directly from the outlet.
• Immediately repair or replace all faulty or damaged service cables. Do not use cords that have cracks or abrasion damage on the length of the cord or on the plug.
• When moving your refrigerator, take care not to roll over the electrical cord.
  • DO NOT store or use gasoline or other combustible liquids or vapors in proximity with this or any other electrical appliance.
• DO NOT permit children to climb, stand or swing from the doors or shelves of the refrigerator. This can cause serious injury to them and damage to the product.
• Keep your fingers away from areas in which they can become caught, such as the doors, hinges and cabinets. Be careful closing the doors when children are near.
• Unplug the refrigerator before cleaning or repairing.

NOTE: We strongly recommend that any repair services be performed by a qualified professional.

• Never store explosive substances or chemicals in your refrigerator such as benzene, alcohol, aerosolcans, etc. It is DANGEROUS!!
• This appliance is intended to be used in household and similar applications such as: staff kitchen areas in shops, offices and other working environments; farm houses and by clients in hotels, motels and other residential type environments; bed and breakfast type environments; catering and similar non-retail applications. For your safety, this product should be properly grounded. Have a qualified professional check the electrical circuit and outlet to ensure a proper ground connection.
• Do not keep bottles in the freezer compartment, they could explode after freezing and cause damage.
• Read all instructions before utilizing the product. Utilize this product only as explicitly expressed in this guide.
• Once the refrigerator is operating, avoid touching cold surfaces of the freezer with damp or wet hands; the skin could become adhered to these surfaces.
• In refrigerators with an automatic ice dispenser, avoid contact with moving parts of the ejector mechanism or with the heating mechanism that discharges the cubes. DO NOT place your fingers or hands in the ice dispenser mechanism while the refrigerator is connected.
• If the use of this unit is no longer needed, please contact local authorities to dispose of this product in a safe way due to Cyclopedia or pentane as gas for insulation and R600a as refrigerant. Insulation gases and refrigerant require a special elimination process. This product contains flam-mable insulation and refrigerant.
• DO NOT refreeze foods which have already thawed. The Department of Agriculture of the United States, in your Bulletin of Home and Gardens No. 69 establishes that:

"...You can refreeze food that has thawed if they contain ice crystals or are cold and below 40 °F (4 °C)".

"...Ground beef, perishable food or seafood that is discolored or has an unpleasant odor should not be frozen or consumed.

Consumption of melted ice cream should also be avoided. If the odor or color of food is questionable, discard it. The food may be dangerous to consume".

"Partial thawing or refreezing reduces the quality of the food, especially fruit, vegetables and prepared meals.

The quality of red meat is less affected than that of other foods. Use refrozen products as soon as possible in order to maintain their quality".

• Do not use mechanical devices or other means to accelerate the defrosting process.
• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

Risk of Fire and Flammable Materials

This symbol alerts you to flammable materials that can ignite and cause a fire if you do not take care.
*Refrigerant type is indicated in the label inside your refrigerator, this warning apply just for models with R600a refrigerant.
- This appliance contains a small amount of isobutane refrigerant (R600a), but it is also combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged.

- If a leak is detected, avoid any naked flames or potential sources of ignition and air the room in which the appliance is standing for several minutes. In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance is used should correspond to the amount of refrigerant used. The room must be 1m^2 in size for every 8g of R600a refrigerant inside the appliance.

• When positioning the appliance, ensure the supply cord is not trapped or damaged.
• Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.

KEEP THESE INSTRUCTIONS

CAUTION

This appliance is not intended for use by children, persons with physical or mental disabilities, persons with reduced sensory or mental capacity, or persons that lack experience or know-how, unless they have supervision or instruction in relation to the use of the appliance by the person responsible for their safety. Children should be supervised to assure that they do not play with the appliance.

DANGER: CHILDREN MAY BECOME TRAPPED

Children becoming trapped or suffocated is not a problem of the past. Discarded and abandoned refrigerators are a hazard, even if they remain there "for just a few days". If you would like to dispose of your old refrigerator, please follow the instructions below to prevent any accidents.

BEFORE DISPOSING YOUR REFRIGERATOR OR FREEZER WHEN NO LONGER IN USE:

• Remove the doors.
• Leave the shelves in place so that children cannot easily become stuck in them.

CFC DISPOSAL

Your old refrigerator may have a cooling system that uses CFC's (chlorofluorocarbons). CFC affects the stratospheric layer of the ozone.

If you decide to throw out your old refrigerator, ensure that CFC contaminants are properly disposed of by a qualified professional. If you intentionally remove the CFC refrigerant, you could be subject to fines or prison in accordance with environmental legislation in effect.

REQUIREMENTS FOR GROUND CONNECTION

IMPORTANT: Attentively read the following.

TO CONNECT ELECTRICITY

WARNING

ELECTRICAL SHOCK HAZARD

FOR YOUR PERSONAL SAFETY, this appliance must be properly grounded. Have a qualified electrician check your wall outlet to ensure that the plug is grounded properly.

3 prong grounding type wall receptacle 3 prong grounding plug Ensure proper ground exists before use

*Image may vary according to your national plug, reference only

RECOMMENDED GROUNDING METHOD

Your refrigerator must always be plugged to its own outlet which is adequately grounded. The energy current should only be 220-240 V \~ 50/60 Hz, AC (according to the National rating) and fused at 15 A.

This provides the best performance and prevents an overload which could cause a fire from the overheating of the cables. It is recommended that a separate circuit be used for this appliance, as well as a receptacle that cannot be disconnected with a switch.

It is your responsibility and obligation to replace two-prong outlets with that of an adequately grounded three-prong outlet.

Do not, under any circumstance, cut or extract the third prong from the plug.

NOTE: Before installation, cleaning or replacing LED lamp, you must disconnect the appliance from the power source. When finished, plug the appliance back in and adjust the thermostat to the desired position.

WARNING

EXTENSION CABLE

Do not use an extension cable.

USE OF EXTENSION CABLES

We do not recommend the use of extension cables. However, if you still choose to utilize an extension cable, it is absolutely necessary that it supports three-pronged plugs and that the electrical current support a minimum of 15 A and 220-240 V (according to the National rating).

The use of an extension cable will increase the amount of space needed behind the refrigerator.

WARNING

REPLACING ELECTRICAL CABLE

If the power cord is damaged, it must be replaced by our service center or qualified LG technician to avoid any risk.

A B C D E F G H I O J K L M N

Use this page to become more familiar with the parts and features of your refrigerator. Page references are included or your convenience.

NOTE: This guide covers several models. The refrigerator you have purchased may have some or all of the items listed below. The locations of the features shown below may not match your model.

* Optional Parts: Not included with all models

A F- Deco Duct*
B Ice Tray
C Freezer Shelf
D Freezer Temperature Control
E Refrigerator Temperature Control
F Shelves
G Refrigerator or Lights (LED)*

H Pantry Drawer*
I Crispers
J Freezer Light (LED)*
K Freezer Door Bins
Diary Bin
M Refrigerator Door Bins
N Refrigerator Door Bin
Smart Functions* Door Alarm*

WARNING

EXCESSIVE WEIGHT HAZARD

Use the assistance of two or more persons to move or install the refrigerator. Not following these instructions may cause injury to the back and other parts of the body.

UNPACKING

Before installing your refrigerator, remove any tape or temporary stickers. Do not remove any stickers that feature warnings, the model serial number or the technical label of the product located on the back of the refrigerator.

To remove adhesive tape residue, rub it well with you fingers and a little liquid detergent. Clean with warm water and let dry.

Do not use sharp instruments, rubbing alcohol, flammable liquids or abrasive cleaning products to remove the adhesive tape or glue. These products can damage the surface of your refrigerator. For more information, see the section on "Important Safety Instructions".

The shelves come already installed in their factory position. Remove the shelves and replace them according to your spacing needs.

Moving Your Refrigerator:

Your refrigerator is extremely heavy. Make sure you protect the floor when moving your refrigerator for cleaning or servicing. Always pull your refrigerator straight out when moving it. Do not shift from side to side or "walk" the refrigerator when attempting to move it as this can cause damage to the floor.

WARNING

EXPLOSION HAZARD

Keep all flammable materials and vapors (such as gasoline) away from the refrigerator. Not following these instructions may cause death, explosion or fire.

INSTALLATION

1. Avoid placing the unit near heat sources, direct sunlight, or humidity.

2. To avoid vibration, the unit should be leveled. If needed, adjust the leveling screws to compensate for an unleveled floor. The front should be slightly taller than the rear to ensure that the doors close properly. The leveling screws can easily be turned by slightly tilting the front of the refrigerator, turning the leveling screws clockwise ( ) to raise it and counter-clockwise ( ) to lower it.

3. Install the refrigerator in an area between 55 °F (13 °C) and 110 °F (43 °C). If the surrounding temperature is lower or higher than previously mentioned, it can adversely affect the unit.

CAUTION: Avoid placing the unit near heat sources, direct sunlight or humidity.

ONCE INSTALLED

1. Carefully clean your refrigerator and remove and dust accumulated during shipping.
2. Install accessories such as the ice bin, door racks, shelves, etc., in their proper places. These are already packed to prevent any possible damage during shipping.
3. Leave your refrigerator on for 2 to 3 hours before storing food inside. Verify that there is a flow of cold air in the freezer compartment to ensure proper cooling. Your refrigerator is now ready for use.

WARNING:

• Take care when working with the hinges, base cover and stops, etc. You may injure yourself.
- DO not place your hands or any tools in the air vents, the base cover or in the bottom of the refrigerator. This may cause injury or electrical shock.

Keep a Proper Distance from Adjacent Objects

Please keep the refrigerator at an adequate distance from other objects. Insufficient spacing can reduce the refrigerator's freezing efficiency and increase electricity consumption.

2" (5.08 cm) 2" (5.08 cm) 2" (5.08 cm)

REFRIGERATOR INSTALLATION

HOW TO REMOVE AND INSTALL THE REFRIGERATOR DOORS

If entrance is less than 35 inches wide, the refrigerator's door will need to be removed.

IMPORTANT: Before starting, turn off and unplug the refrigerator. Remove all food and the racks from the doors.

TOOLS YOU MIGHT NEED OR USE

Hex Socket Wrench

1/4 in (6 mm) 3/8 in (10 mm)

Phillips Screwdriver No. 2

Flat Head Screwdriver

WARNING

ELECTRICAL SHOCK HAZARD

Before you begin, either unplug the refrigerator or turn off the power at the circuit breaker or fuse box. Remove food and any door rack from the refrigerator. Failure to do so could result in death or serious injury.

1. Removing Freezer Door

• Gently pry off the Top Hinge Cover with a flat head screwdriver and remove it. See Fig. 1.

Line drawing of a hand using a screwdriver to lift a block on a mechanical component (no text or symbols)

- Using 10 mm or 3/8 inch socket wrench, remove the three bolts and lift the Top Hinge (See Fig. 2). Set parts aside.

Technical line drawing of a mechanical bracket with mounting holes and a pull-up arrow (no text or symbols)

- Lift freezer door slightly and remove it (See Fig. 3) Set parts aside.

Fig. 3 Middle Hinge Bracket Hinge Pin

2. Removing Refrigerator Door

- Loose and remove the two bolts and the screw to remove the middle hinge bracket from refrigerator housing (Figure 4). Set parts aside (Figure 5).

Fig. 4 Middle Hinge Bracket

Technical diagram of a mechanical assembly with a bracket and mounting base, labeled Fig. 5 (no text or symbols on the diagram itself)

- Lift up door slightly and remove it (See Figure 6).

REFRIGERATOR INSTALLATION

Diagram of a mechanical device with an arrow indicating upward motion, no text or symbols present

• To replace doors, begin with refrigerator door and then follow with freezer door.

3. Replacing Refrigerator Door

• Set door on Bottom Hinge Pin (See Figure 7).
• Place hinge pin of middle bracket inside the hinge pin insert on the top of the door (See Figure 8). Hold the door in place and line up the hinge with the holes in the refrigerator housing.

Fig. 7 Bottom Hinge Pin

Technical diagram of a mechanical assembly with a bracket and mounting base (no text or symbols)

- Use the two bolts and the screw to refasten the middle hinge with the refrigerator housing. See Figure 9.

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

4. Replacing Freezer Door

• Set the freezer door onto the Middle Hinge pin (Figure 10).
• Place upper hinge in the top of the freezer door and line up the hinge with the holes in top of refrigerator. Use the three bolts to fasten the hinge (See Figure 11).

Technical line drawing of a mechanical bracket with mounting holes and a downward arrow indicating force or adjustment (no text or symbols)

Technical line drawing of a mechanical bracket with bolts and a downward arrow indicating a detail (no text or symbols present)

- Carefully, force the top hinge cover back into place over hinge (See Figure 12).

Technical line drawing of a mechanical component with two clamps and a base, labeled Fig. 12 (no text or symbols on the diagram itself)

REFRIGERATOR INSTALLATION

HOW TO REVERSE AND INSTALL THE REFRIGERATOR DOORS

NOTE: Door reversal must be done by an authorized installer or service person.

You may find it more convenient to have the doors converted from the left opening type (factory installed) to the right opening type. Directions refer to the right side as the side on your right as you face the unit.

TOOLS YOU MIGHT NEED OR USE

1/4 in (6 mm) 3/8 in (10 mm)

Hex Socket Wrench

Phillips Screwdriver No. 2

Flat Head Screwdriver

WARNING

ELECTRICAL SHOCK HAZARD

Before you begin, either unplug the refrigerator or turn off the power at the circuit breaker or fuse box. Remove food and any door rack from the refrigerator. Failure to do so could result in death or serious injury.

1. Removing Freezer Door

Gently pry off the top hinge cover with a flat head screwdriver and remove.

Line drawing of a hand using a screwdriver to lift a rectangular object (no text or symbols)

Using 10mm or 3/8 inch socket wrench, remove the three bolts and lift off the top hinge. Set parts aside.

Technical line drawing of a mechanical component with bolts and a bracket, labeled Fig. 2 (no text or symbols on the diagram itself)

Slightly lift up the refrigerator door and remove it.

Middle Hinge Bracket Hinge Pin

Turn the freezer door upside down on a non-scratch surface.

Loosen the screw to remove the Door Closer/Stop and Hinge Pin Insert.

Move the Hinge Pin Insert Bracket to the other side of the door, keeping the same orientation, and move the Hinge Pin Insert into the hole on the left side of the bracket.

Hinge Pin Insert Hinge Pin Insert Bracket

Reverse the Door Closer/Stop by flipping it over. Place it on top of the Hinge Pin Insert Bracket, and tighten both down with the screw.

Mechanical component diagram showing a screw being inserted into a housing (no text or symbols)

Pry off the cover on the top left side of the refrigerator to uncover the screw holes.

Set the freezer door and top hinge parts to the side and remove the refrigerator door.

Cover (on top of refrigerator)

REFRIGERATOR INSTALLATION

2. Reversing and Reinstalling Refrigerator Door

Using a 1/4" socket wrench, loosen and remove Hinge Pin from the Middle Hinge Bracket. Remove washer underneath the middle hinge and set aside. NOTE: At this point the door will be loose. Slightly lift the door and remove it.

Technical line drawing of a mechanical assembly with mounting bracket and screw mount (no text or symbols)

Diagram of a mechanical device with an arrow indicating upward motion, showing a knob and adjustment knob (no text or symbols)

Loosen and remove the two bolts and use the Phillips head screwdriver to remove the Middle Hinge Bracket from the refrigerator housing. Set parts aside.

Technical line drawing of a mechanical hinge or latch mechanism (no text or symbols)

Remove the washer from the Bottom Hinge Pin. Using a 1/4" socket wrench, loosen and remove the Hinge Pin from the Bottom Hinge. Reattach the Hinge Pin to the opposite side of the hinge. NOTE: This is easier to do while the hinge is still attached.

Technical line drawing of a mechanical assembly with a bracket and mounting base (no text or symbols)

Technical line drawing of a mechanical assembly with a tool and mounting base (no text or symbols)

Using a 3/8" socket wrench with a 2-Inch extension and screwdriver, loosen the two bolts and one screw, and remove the Bottom Hinge from right side of the housing.

Technical diagram of a mechanical clamp or bracket assembly with screws and a central component (no text or symbols)

Remove the Decorative Caps on the bottom of the refrigerator housing. You will need these holes for the Bottom Hinge.

Technical line drawing of a mechanical bracket with screws and fasteners (no text or symbols)

Move the Bottom Hinge to the left side of the housing, keeping the same orientation, and reattach with the two bolts and one screw. The flat screw must be placed on the exterior side of the hinge. Move the Decorative Bolt to the hole on the lower right side of the housing.

Leveler

Turn the refrigerator door upside down on a non scratching surface. Loosen the three screws to remove the hinge pin bracket, the hinge pin insert and the door closer.

WARNING: If you reinstall or replace doors, move the leveler to the opposite side. NOTE: The leveler feature only applies on some models.

REFRIGERATOR INSTALLATION

Door Closer/ Stop Hinge Pin Bracket Hinge Pin Insert

Reverse the Door Closer/Stop by flipping it over. Place the hinge pin bracket, and the hinge pin insert keeping the same orientation on the opposite door side, then place the door clooser on top, and tighten the 3 philliphs screws.

Door Closer/ Stop Hinge Pin Bracket Hinge Pin Insert

With a flat-head screwdriver, carefully pry off and remove the cover over the screw holes on the left side of refrigerator housing.

Technical line drawing of a mechanical component with screwdriver and three inserted pins (no text or symbols)

Remove the outer lower Decorative Screw from the housing at the area between the freezer and refrigerator doors (You will need this hole for the Middle Hinge Bracket.)

Technical line drawing of a car door panel with mounting holes and a screwdriver (no text or symbols)

Flip the Middle Hinge Bracket, (flange will now be on top) position it on left side of the refrigerator and reattach with two bolts and a Phillips screwdriver. Place the refrigerator door down over the pin on the bottom hinge. Place the washer between the refrigerator door and middle hinge and re-attach Hinge Pin to Hinge Bracket with a 1/4" socket wrench.

NOTE: Bracket has been flipped, but Hinge Pin stays in the same orientation with its hexagonal end facing upward.

Flange Middle Hinge Bracket

Insert the Decorative Screw into the outer hole on the rightside of the housing. Attach cover on the right side. Cover is force-fitted.

Decorative Screw

REATTACHING THE DOORS

Place the freezer door down over the Hinge Pin on the Middle Hinge Pin Bracket.

Technical line drawing of a mechanical bracket with a bolt and mounting bracket (no text or symbols)

Place the Upper Hinge Pin on top of the freezer door and line up the Upper Hinge with holes on top of the refrigerator. Use the three bolts to replace the Hinge.

Technical line drawing of a mechanical bracket with mounting holes and a downward arrow indicating a detail (no text or symbols present)

Tighten the bolts. Force-fit Top Hinge Cover over Top Hinge.

Technical line drawing of a mechanical bracket or bracket with no visible text or symbols

Replace cover on the top left side of the refrigerator to the right top to cover the holes. Cover is also force-fitted.

Cover (on top of refrigerator)

After changing doors, make sure that the corners of the Door Gaskets are not folded over. To ensure a good seal, apply a small amount of silicon grease on the corners of gaskets.

Corners

CLOSING THE DOORS AND LEVELING

To avoid vibration, the unit must be leveled. If necessary, adjust the leveling legs to compensate for unevenness of the floor. The front should be slightly higher than the rear to aid in door closing.

The refrigerator has two front leveling legs, one on the right and one on the left. If your refrigerator seems unstable or if you would like the doors to close more easily, simply adjust the tilt of the refrigerator by following the instructions below:

1. Plug the refrigerator into a 3 prong grounded outlet. Move the refrigerator into its final position.
2. Use an 11/16" (18 mm) wrench or an adjustable wrench to adjust the leveling legs, turn the leveling legs to the left to raise that side of the refrigerator or to the right to lower it. It may take several turns of the leveling leg to adjust the tilt of the refrigerator.

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling legs. This will make it easier to adjust the level.

1. Open both doors again and check to make sure that they close easily. If they don't, tilt the refrigerator slightly more to the rear by turning both leveling legs to the left. It may take several more turns, and you should extend both legs the amount.

Line drawing of a refrigerator next to a mechanical device with wrench and belt components (no text or symbols)

Door Alignment

If the space between your doors is uneven, follow the instructions below to align the doors:

1. Gently pry off the Top Hinge Cover with a flat head screwdriver and remove.
2. Loosen the Top Hinge Bolts using a 10 mm or 13/32 inch socket wrench or open-end wrench.
3. Have someone hold the freezer door so the space between the two doors is even, and retighten the top hinge bolts.
4. Replace the Top Hinge Cover.

USING YOUR REFRIGERATOR

ENSURING PROPER AIR CIRCULATION

In order to obtain stable temperature, the air must flow between the freezer and refrigerator sections. As shown in the illustration below, the cold air enters through the bottom part and circulates upward. This air returns below the freezer floor and the rest of the air enters the refrigerator section through the top vent.

Diagram of an open refrigerator showing internal air circulation and battery compartments (no text or labels)

Do not block any of these vents with packages of food. This can interrupt the flow of air and cause temperature and moisture problems.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To prevent odor transfer and drying out of food, make sure you wrap or cover foods tightly (See the "Food Storage Guide" section for details).

NOTE: If you close the fresh food compartment door applying more force than necessary, freezer door may get open and close again, due internal air flow of refrigerator.

Cross-sectional diagram of a mechanical or fluidic device with directional arrows indicating flow or movement (no text or symbols)

ADJUSTING THE CONTROLS

- Your refrigerator has two controls that allow you to regulate the temperature the freezer and refrigerator compartments.

• Refrigerator Control

Initially set the Refrigerator Control on the middle setting (number 3). To do so, press the TEMPERATURE ADJUST button until it reaches the middle position (the third LED turns ON). Leave the refrigerator on this setting for 24 hours to reach the correct temperature. After 24 hours, adjust the compartment temperature as you desire. ALWAYS wait 24 hours before you adjust the temperature. If you want to set the refrigerator compartment temperature to a warmer temperature than the current, continue pressing the TEMPERATURE ADJUST button until it reaches the desired temperature.

Cold Off Coldest Temperature Adjust

• Demo Mode (For Store Use Only)

Demo Mode disables all cooling in the refrigerator and freezer sections to conserve energy while on display in a retail store. When activated, OFF will display on the control panel.

To deactivate:

Press the TEMPERATURE ADJUST button until your desired temperature setting is reached. The OFF light will turn off once the Demo Mode is deactivated.

- Freezer Control

The freezer control should come from factory on the middle setting (number 3). Wait 24 hours before adjusting the freezer compartment temperature. Roll the knob to set the freezer temperature as you desire. ALWAYS wait 24 hours after any adjustment to reach the desired temperature.

NOTE: Setting at higher number of the freezer compartment, the temperature of freezer compartment becomes colder.

Allow 24 h for adjustments Espesor 24 h para釧り cambias Coldest Mas Frio 5 4 3 2 1 Cold Frio Recommended Recommendado 3 Temperature Control Freezer / Competitor

ADJUSTING CONTROL SETTINGS

Give the refrigerator time to cool down completely before adding food. It is best to wait 24 hours before adding food to the refrigerator. The mid-settings indicated in the previous section should be correct for normal household refrigerator usage. The controls are set correctly when milk or juice is cold to your liking and ice cream is firm.
The refrigerator control functions as the thermostat for the entire appliance. The higher the number setting, the longer the compressor will run to keep the temperature colder. The freezer control adjusts the cold air flow from the freezer to the refrigerator. Setting the freezer control to a lower temperature keeps more cold air in the freezer compartment to make it colder.
If you need to adjust the temperature in the refrigerator or freezer, begin by adjusting the refrigerator first. Wait 24 hours after the refrigerator adjustment to check the freezer temperature. If it is too warm or too cold, then adjust the freezer control as well.
Use the settings listed in the table below as a guide.

CONDITION/REASON: RECOMMENDED ADJUSTMENT:
REFRIGERATOR section is too warm• Opening the door often• Adding a large amount of food• Room temperature is very warm	Adjust the REFRIGERATOR setting to the next highest number and wait 24 hours, then check.
FREEZER section is too warm/ ice is made too slowly• Opening the door often• Adding a large amount of food• Room temperature is very low (not cycling often enough)• Using ice frequently• Air vents blocked by objects	Adjust the FREEZER setting to the next highest number and wait 24 hours, then check.Remove any objects blocking air flow.
REFRIGERATOR section is too cold• Controls not set correctly for your conditions	Adjust the REFRIGERATOR setting to the next lowest number and wait 24 hours, then check.
FREEZER section is too cold• Controls not set correctly for your conditions	Adjust the FREEZER setting to the next lowest number and wait 24 hours, then check.

FOOD STORAGE GUIDE

ITEMS HOW TO STORE
Storing Fresh Food	Wrap or store food in the refrigerator in airtight and moisture-proof material unless otherwise noted. This prevents food odor and taste transfer throughout the refrigerator. For dated products, check date code to ensure freshness.
Butter or margarine	Store opened butter in a covered dish or in a closed compartment. When storing a larger quantity, wrap in freezer packing and freeze.
Cheese	Store in original packaging until you are ready to use it. Once opened, tightly rewrap with plastic wrap or aluminum foil.
Vegetables with skins (carrots, peppers)	Place in bags or plastic containers inside the crisper.
Fruit	Wash and let dry; store in plastic bags in the refrigerator. Do not wash or pit berries until you are ready to eat them. Berries should be selected and kept in their original packaging (if there is any) or in a paper bag closed halfway and set on a shelf.
Leafy Vegetables	Remove original packaging and trim any dirty or discolored parts. Wash in cold water and drain. Place in a plastic bag or plastic container and store in the crisper.
Fish	Consume fish or seafood the same day purchased.
Chef Fresh	Store any meat in original airtight, moisture-proof packaging. Rewrap if necessary.
Leftovers	Cover leftovers with plastic wrap or aluminum foil. Plastic containers with airtight lids can also be used.

Packaging Recommendations:

• Use sealed plastic containers.
- Use plastic containers with a smooth surface.
• Package with aluminum foil of high resistance.
- Wrap with paper layered with plastic.
- Use water proof plastic.
- Use recommended plastic bags to store frozen foods.

Follow these packaging or container instructions in order to reach the best freezing.

USING YOUR REFRIGERATOR

Do not use:

• Bread Wapping.
• Plastico safeinfectoring. or
• Containers seal out lids or
• Wax/wapier or ed pla
• Thin wrap/wrap roof er or n er p

Freezing

IMPORTANT: Do not take freeze in the or compa tmen, they may explore af zing and cause damage.

For the an ximuruse of your freezer do not store exces food. Dot introduce a large amount unfrozen foods that cannot be frozen within 24 hours (no more than 2 - 3 pounds or 0,91 kg - 1,36 kg of food per square inch of space in the freezer). Sufficient space must be left in order for the air to circulate properly around the packages. Leave enough space in order to close your refrigerator with out difficulty.

Storage times can vary depending on the type and quality of the food, the way its package, or packaging container used, (in comparison to air and humidity), and the temperature it being stored in. Ice crystals formed inside your package are normal it indicates the air and humidity inside your package have condensed.

NOTE: Let warm foods cool off at room temperature for approximately 30 min, then wrap accordingly with the methods mention above and freeze. By letting your warm foods cool off before you introduce them to your freezer will ray.ene

WARNING

SUFFOCATING DANGER

Adequate ventilation is required when using dry ice. Dry ice is Carbon Dioxide (CO2). When it evaporates it produces oxygen, causing dizziness, slight headaches, unconsciousness or death. Do not inhale these vapors and properly ventilate the room while in use of dry ice.

REFRIGERATOR SHELVES

The glass shelves in your refrigerator are adjustable to meet your individual storage needs.

Adjusting the shelves to fit different heights of items will make finding the exact item you want easier. Doing so will also reduce the amount of time the refrigerator door is open which will save energy.

IMPORTANT: Do not clean glass shelves with warm water while they are cold. Shelves may break if exposed to sudden temperature changes or impact.

NOTE: Glass shelves are heavy. Use special care when removing them.

Adjusting Shelves

Remove shelves from the shipping position and replace shelves in the position you want.

• To remove a shelf: Tilt up the back of the shelf in the direction of ① and lift it in the direction of ②. Pull the shelf out.

Diagram showing two labeled components (① and ②) with directional arrows indicating movement or flow between them.

• To reinstall a shelf: Slide the shelf into the guides until it stops.

Illustration of a hand pressing down on a rectangular electronic device with a black arrow indicating motion (no text or symbols)

PANTRY DRAWER (on some models)

- To remove the Pantry Drawer: Grasp the drawer handle and pull it forward to the drawer stop. Lift up and pull out.

Diagram of an open refrigerator showing internal compartments with labeled parts and directional arrows indicating storage or ventilation.

• To replace the Pantry Drawer: Slide the drawer back all the way past the drawer stop.

USING YOUR REFRIGERATOR

ICE TRAY

- Pour potable water to the indicated level in the picture. Do not overfill with water or ice cubes will be difficult to remove.

ed I zer

- For quick freezer, adjust the freezer dial to 3.

• Do not bend the ice tray, dping so may result in damage to the tray.

Line drawing of hands holding a handheld electronic device with a scroll wheel (no text or symbols)

• To remove ice cubes easily, pour water on the back of the tray soak it in water before removing ice cubes.

WARNING:

Fill with potable water only.

The crispers provide fresher tasting fruit and vegetables by letting you easily control humidity inside the drawer.

You can control the amount of humidity in the moisture sealed crispers by adjusting the control to any setting between VEGETABLES and FRUIT.

• VEGETABLES keeps moist air in the crisper for best storage of fresh, leafy vegetables.
• FRUIT lets moist air out of the crisper for best storage of fruit.

To remove and install the crisper drawers:

1. Pull the crisper drawer out to the drawer stop.
2. Lift the front of the crisper up, then pull it straight out.
3. To install, slightly tilt up the front, insert the drawer into the frame and push it back into place, past the drawer stop.

Line drawing of a hand inserting a device into a rack (no text or symbols)

To remove the crisper glass:

1. Remove the crisper drawers (as described above).
2. Reach in under the glass and lift up.
3. Gently push the glass up and out.

Line drawing of hands inserting a device into a cabinet (no text or symbols)

To remove the crisper cover:

1. Remove both crisper drawers.
2. Remove the crisper glass.
3. While holding the support and crisper cover, pull up and out.

Illustration of a hand cleaning a window with a tool, showing a curved arrow indicating direction (no text or symbols)

DOOR BINS

The door bins are removable for easy cleaning and adjustment.

1. To remove the bin, simply lift the bin up and pull straight out.

2. To replace the bin, slide it in above the desired support and push down until it snaps into place.

Technical line drawing of a mechanical or architectural component with no visible text or symbols

NOTE: Some bins may vary in appearance and will only fit in one location.

DAIRY BIN

1. To remove the Dairy Bin, simply lift up and pull out.
2. To replace the Dairy Bin, slide it in above the desired support slots and push down until it stops.

Dairy Bin

REFRIGERATOR CARE AND CLEANING

WARNING

EXPLOSION HAZARD

Do not use flammable cleaners. Not following these instructions can cause death, explosion or fire.

The refrigerator, as well as the freezer, do their own de-freezing. This process does not prevent the build up of contaminants, therefore it is suggested that you clean both parts once a month; clean spilled liquids immediately.

REFRIGERATOR CLEANING

• Unplug your refrigerator.

• Pull out all of the removable parts (such as the vegetable and dairy doors).
- Use a clean sponge (or a soft rag) and use it with lukewarm water mixed with detergent. Do not use abrasive or concentrated cleaners.
• Hand wash it, and dry it thoroughly.
• Plug the refrigerator back in.

OUTSIDE

NOTE: Avoid the usage of chemical products that contain phosphates or bleach.

INSIDE (Allow freezer to slightly warm up a small degree to prevent cloth from sticking)

In order to eliminate bad odors, clean the inside of the refrigerator with a mixture of baking powder and lukewarm water (one teaspoon of baking powder per cup of water). Ensure that the powder dissolves thoroughly, in order to prevent any sort of damage.

Use only a mild detergent (such as dish soap).

PLASTIC PARTS (Covers and Panels)

NOTE: Back Cover should only be

removed by a qualified technician.

In order to get an efficient performance of your refrigerator, clean the back cover of it at least twice a year.

REPLACING REFRIGERATOR LIGHTS

The refrigerator and freezer compartment lights are LED interior lighting, and service should be performed by a qualified technician.

POWER INTERRUPTIONS

1. In case of a black out, call your electric company and ask how long it will last.
2. In case of a 24 hour or less black out, do not open the refrigerator; this will keep the food fresh.
3. In case of a longer black out, do one of the following options:
   • Pull out all of the frozen food and keep them in an ice chest.
4. Put 2 lbs (907 g) of frozen ice (make sure you use gloves) for each square foot (28 L) inside the freezer. This task will preserve the food fro 2 to 4 days.
   • In case you do not possess neither ice chest or dry ice, consume your food as soon as possible.

REMEMBER: In a power failure, a full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be safely refrozen, although the quality and flavor may be affected. If the condition of the food is poor or if you feel it unsafe, dispose of it.

WHEN GOING ON VACATION

If you decide to leave your refrigerator on when going away, consider these steps:

1. Consume all of the perishable items and freeze the rest.

2. Empty the ice bin.

If you decide to leave your refrigerator off:

REFRIGERATOR CARE AND CLEANING

WHEN MOVING

If you decide to take your refrigerator with you when moving, consider the following:

1. Remove all of the food from it, and place the frozen food in an ice chest with dry ice.
2. Unplug your refrigerator.
3. Empty the water from its tray.
4. Clean and dry it with a rag
5. Pull out all of the removable parts, and wrap them with adhesive tape.
6. Depending on the model of the refrigerator, lift the top part of the refrigerator so it can roll with ease, or screw the levelers so it won't scratch the floor. Consult to the section "Closing and Aligning Doors".
7. Keep the doors closed with the cable glued to the refrigerator cabinet with an adhesive tape.

When your refrigerator arrives to your home, put everything back into place and read the section "Refrigerator Installation" in order to obtain installation preparation.

DOOR ALARM (On Some Models)

The Door Alarm function is designed to prevent refrigerator malfunctions that could occur if the refrigerator door remains open. If the refrigerator door remains open for longer than 1 minute, an alarm sounds at 30-second intervals. The alarm will stop when both refrigerator doors are closed properly.

NOTE: This function can not be deactivated.

Line drawing of an open refrigerator with doors open, showing internal compartments and front panel (no text or labels)

SMART FUNCTIONS

LG ThinQ Application

This feature is only available on models with the 📄 or Ⓤ logo.

The LG ThinQ application allows you to communicate with the appliance using a smartphone.

LG ThinQ Application Features Communicate with the appliance from a smartphone using the convenient smart features.

Smart Diagnosis

- If you experience a problem while using the appliance, this smart diagnosis feature will help you diagnose the problem.

NOTE

• The application is subject to change for

Smart Diagnosis

This feature is only available on models with the or 📞 logo.

Use this feature to help you diagnose and solve problems with your appliance.

NOTE

• For reasons not attributable to LGE's negligence, the service may not operate due to external factors such as, but not limited to, Wi-Fi unavailability, Wi-Fi disconnection, local appstore policy, or app unavailability.
• The feature may be subject to change without prior notice and may have a different form depending on where you are located.

Using Audible Diagnosis to Diagnose Issues Follow the instructions below to use the audible diagnosis method.

- Launch the LG ThinQ application and select the Smart Diagnosis feature in the menu. Follow the instructions for

TROUBLESHOOTING GUIDE

UNDERSTANDING SOUNDS YOU MAY HEAR

Your new refrigerator may make sounds that your old one did not make. Most of the new sounds are normal. Hard surfaces, like the floor, walls and cabinets, can make the sounds seem louder than they actually are. The following describes the kinds of sounds you may hear and what may be causing them.

Clicking:

The defrost control will click when the automatic defrost cycle begins and ends. The thermostat control (or refrigerator control, depending on the model) will also click when cycling on and off.

Rattling:

Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.

Whooshing:

- Evaporator fan motor circulating the air through the refrigerator and freezer compartments.

• Air being forced over the condenser by the condenser fan.

- Ice compartment fan in the freezer on the left side of the refrigerator when the doors are open.

Gurgling

As each cycle ends, you may hear a gurgling sound caused by the refrigerant flowing through the cooling system.

Popping:

Contraction and expansion of the inside walls.

Sizzling:

Water dripping on the defrost heater during a defrost cycle.

Vibrating Noise:

If the side or back of the refrigerator is touching a cabinet or wall, some of the normal vibrations may make an audible sound. To eliminate the noise, make sure that

the sides and back cannot vibrate against any wall or cabinet.

Dripping:

Water running into the drain pan during the defrost cycle.

Pulsating or High-Pitched Sound:

Your refrigerator is designed to run more efficiently to keep your food items at the desired temperature.

The high efficiency compressor may cause your new refrigerator to run longer than your old one, but is still more energy efficient than previous models. While the refrigerator is running, it is normal to hear a pulsating or high-pitched sound.

Problem Possible Causes Solutions
	The power supply cord is unplugged. Firmly plug the cord into a live outlet with proper voltage (see Electrical & Grounding Requirements)
	A household fuse has blown or a circuit breaker has trapped	Replace the fuse or reset the circuit breaker. If the problem persists, contact an electrician
	The refrigerator control is set to the	Refer to the Setting the Controls section.

TROUBLESHOOTING GUIDE

Problem Possible Causes Solutions
Lights do not work	The power supply cord is unplugged. Firmly	plug the cord into a live outlet with proper voltage (refer to Electrical & Grounding Requirements).
	An LED light has malfunctioned. Before proceeding to replace LED, unplug the refrigerator or turn off power at the circuit breaker or fuse box.NOTE: The refrigerator and freezer compartment lamps are LED interior lighting, and service should only be performed by a qualified technician.
Vibration or rattling noise.	The refrigerator is not resting solidly on the floor.	Floor is weak or uneven or leveling legs need adjusting. See the Installation section for leveling instructions.
Compressor seems to run too much.	The refrigerator that was replaced was an older model.	Modern refrigerators require more operating time but use less energy due to more efficient technology.
	The room temperature is warmer than normal.	The compressor will run longer under warm conditions. At normal room temperatures (70°F) expect your compressor to run about 40% to 80% of the time. Under warmer conditions, expect it to run even more often. The refrigerator should not be operated in surrounding temperatures above 110°F.
	The door is opened often or a large amount of food has just been added.	Adding food and opening the door warms the refrigerator, requiring the compressor to run longer in order to cool the refrigerator back down. In order to conserve energy, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door as soon as the food is removed. (Refer to the Food Storage Guide.)
	The refrigerator was recently plugged in and the refrigerator control was set correctly.	The refrigerator will take up to 24 hours to cool completely
	The refrigerator control is not set correctly for the surrounding conditions.	See the Adjusting Control Settings section.
	The doors are not closed completely. Firmly	push the doors shut. If they will not shut all the way, see "Doors will not close"

TROUBLESHOOTING GUIDE

Problem Possible Causes Solutions
Doors will not close completely.	The refrigerator is not level. See the Leveling and Door Alignment section.
	Food packages are blocking the door open.	Rearrange food containers to clear door and door shelves.
	The ice bin, crisper cover, pans, shelves, door bins or baskets are out of position.	Push bins all the way in and put crisper cover, pans, shelves and baskets into their correct positions. See the Using Your Refrigerator section for more information.
	The gaskets are sticking. Clean gaskets and	the surfaces that they touch. Ruo a thin coat of appliance polish or kitchen wax on the gaskets after cleaning.
	The refrigerator wobbles or seems unstable.	Level the refrigerator. Refer to the Leveling and Door Alignment for more information.
	The doors were removed during product installation and not properly replaced.	Remove and replace the doors according to the Removing and Replacing Refrigerator Handles and Doors section, or call a qualified technician.
Frost or ice crystals on frozen food.	The door is not closing properly. See "Doors will not close completely" in the Troubleshooting section.
	The door is opened often. When the door is opened, warm, humid air is allowed in the freezer, resulting in frost.
Ice has bad taste or odor.	The icemaker was recently installed. Discard the first few batches of ice to avoid discolored or bad tasting ice.
	The ice has been stored for too long. Throw away old ice and make a new supply.
	The food has not been wrapped tightly in either compartment.	Rewrap foods since odors may migrate to the ice if food is not wrapped properly.
	The water supply contains minerals such as sulfur.	A water filter may need to be installed to eliminate taste and odor problems.
	The interior of the refrigerator needs cleaning.	See Care and Cleaning section for more information.
	The ice storage bin needs cleaning. Empty and wash bin. Discard old cubes.
There is water in the defrost drain pan.	The refrigerator is defrosting. The water will evaporate. It is normal for water to drip into the defrost pan.
	It is more humid than normal. Expect that the water in the defrost pan will take longer to evaporate. This is normal when it is hot or humid.

TROUBLESHOOTING GUIDE

Problem Possible Causes Solutions
Temperature is too warm or there is interior moisture buildup.	The air vents are blocked. Cold air circulates from the freezer to the fresh food section and back again through air vents in the wall dividing the two sections.	Locate air vents by using your hand to sense airflow and move all packages that block vents and restrict airflow. (See air flow diagram below).
	The doors are opened often. Opening the door	Door warms the refrigerator, requiring the compressor to run longer in order to cool the refrigerator back down. In order to conserve energy, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door as soon as the food is removed.
	The control is not set correctly for the surrounding conditions.	If the temperature is too warm, change the setting one increment at a time. Refer to the Setting the Controls section. Wait 24 hours for temperatures to stabilize or even out.
	A large amount of food has just been added to the refrigerator or freezer.	Adding food warms the refrigerator. It can take a few hours for the refrigerator to return to normal temperature.
	The food is not packaged correctly. Wrap food	Food tightly and wipe off damp containers prior to storing in the refrigerator to avoid moisture accumulation. If necessary, repackage food according to the guidelines in the Food Storage Guide section.
	The doors are not closing completely. See "Doors will not close completely" in the Troubleshooting section.
	The weather is humid in humid weather, stopper moisture.

TROUBLESHOOTING GUIDE

Problem Possible Causes Solutions
The doors are difficult to open.	The gaskets are dirty or sticky. Clean the gaskets and the surfaces that they touch. Rub a thin coat of appliance polish or kitchen wax on the gaskets after cleaning.
	The door is reopened within a short time after having been opened.	When you open the door, warmer air enters the refrigerator. As the warm air cools, it can create a vacuum. If the door is hard to open, wait one minute to allow the air pressure to equalize, then too if it opens more easily.
Frozen food in refrigerator compartment.	The temperature control in the refrigerator compartment is set too cold.	Press the Temperature Adjust button to set the refrigerator compartment to a warmer temperature.
	Refrigerator is installed in a cold location. When room temperature is below 41°F (5°C), food can freeze. The refrigerator should not be operated in temperatures below 55°F (15°C).
	Food with a high water content was placed too close to the cold air discharge vent.	Place food with a high water content toward the front of the refrigerator.

SPECIFICATIONS

MODELS: LT24CBBVLN / LT24CBBWLH / LT24CBBVLH / LT20CBBWIN / LT20CBBWIN
EN	ENGLISH	PRODUCT FICHE
A	Trade Mark	LG Electronics
B	LT24CBBVLN LT24CBBWLH LT24CBBVLH LT24CBBWLH LT20CBBWIN LT20CBBWIN
C	Category	7 (Refrigerator, Freezer)
D	Energy efficiency class	5			C
E	Annual energy consumption *XYZ* [kWh], based on standard test results for 2-1 hours	307/3.5			3.9
		Actual energy consumption will depend on how the appliance is used and where it is located
F	Fresh Food Storage Volume [L/Cuft]	488/1.2			407/14.2
G	Frozen Food Storage Volume [L/Cuft]	137/1.4			74/14.0
		38/1.3			38/1.4
H	Other compartments Storage Volume 1 /Cu.ft*	-
I	Frozen-Free Compartments	Fresh Food, Frozen Food
J	Temperature Rise time [h]	10.3/4			20
K	Freezing Capacity [kg/24h]	7/5			5.5

LG

Life's Good

ملحاظات

Line drawing of an open refrigerator with doors open, showing internal compartments and front panel (no text or symbols)

عند Zahهات للاجازة

: L-II A III, I, II, III, IV, II, III, IV, III, IV, IV, IV

LG ThinQ تطبيق

Line drawing of a hand cleaning a window with a curved object inside (no text or symbols)

صناديق الباب

Line drawing of a hand inserting a card into a device (no text or symbols)

لازاله رف الرحاج المنموح:

Diagram of a refrigerator interior showing labeled compartments and storage areas with arrows indicating movement or flow.

Simple line drawing of a hand pressing down on a rectangular object (no text or symbols)

Diagram showing two labeled components (① and ②) with directional arrows indicating movement or flow between them.

Line drawing of an open refrigerator with internal compartments and ventilation system (no text or symbols)

Technical line drawing of a mechanical bracket with mounting holes and a downward force arrow (no text or symbols)

Pure technical line drawing of a mechanical component or bracket (no text or symbols)

Technical diagram showing a mechanical component with labeled parts and dimension indicators

تركيبesthesia

Technical line drawing of a mechanical assembly with a lever and base mount (no text or symbols)

Mechanical assembly diagram showing a bracket with bolts and a central knob (no text or symbols)

Technical line drawing of a mechanical assembly with no visible text or symbols

Technical line drawing of a mechanical bracket or clamp assembly (no text or symbols)

Pure mechanical assembly diagram without any text, numbers, or symbols

Technical line drawing of a mechanical hinge or bracket with adjustment knobs (no text or symbols)

تركبesthesia

1/4 in (6 mm) 3/8 in (10 mm)

داسی مفتاح س

2 مفک فلیسی رقم

رأس مفک مسطح

Diagram of a mechanical component with a screw and adjustment knob (no text or symbols)

تحذیر

Line drawing of a hand using a tool to lift a component (no text or symbols)

Labeled diagram of a refrigerator interior showing numbered compartments and doors