GCR1561.07F - Home Automation JUNG - Free user manual and instructions

USER MANUAL GCR1561.07F JUNG

Operating Instructions Radio push button R2.1

Plain white square with rounded corners (no text or symbols)

1. Function

The pushbutton with radio-control receiver permits radio-controlled or manual switching and dimming of lamps. The starting brightness can be stored in the device as memory brightness. The pushbutton with radio-control receiver is plugged onto one of the following inserts:

• Universal touch dimmer 1254 UDE
• Standard touch dimmer 1225 SDE
• Relay insert single-channel 1201 URE
• Relay insert two-channel 1202 URE
• Tronic switching insert 1254 TSE
• LV triac switching insert 1244 NVSE
• Touch control unit 1240 STE

After reception of a data telegram from a programmed radio-control

Important

The present instructions describe the functions of the radio-control pushbutton without lighting control. More information on light control with a presence detector or a light sensor is set out in the operating instructions for these devices.

2. Warning

Caution: The installation and assembly of electrical equipment may only be performed by a skilled electrician.

3. Fitting

The radio-control pushbutton can only be operated in conjunction with the inserts listed under 'Functions'. Connection and fitting are described in the operating instructions of the insert.

Procedure

1. Install the selected insert (1) in a flush-mounting box (deep model recommended), the connecting terminals of the insert pointing downwards.
2. Plug the radio-control pushbutton (2) together with frame (3) onto the insert while the mains voltage is disconnected.

Important

• The distance from electrical appliances (e.g. microwave oven, hi-fi and TV sets) must be at least 0.5 m.
• To prevent saturation of the radio receiver (actuator), the radiocontrol pushbutton must be at least 1 m away from the nearest transmitter.

4. Learning a Radio Transmitter

During programming of a transmitter, the sensitivity of a radiocontrol receiver is reduced to a range of approx. 5 m. The distance between the radio-control pushbutton and the transmitter to be programmed should be between 0.5 m and 5 m.

Procedure

1. Switch off the load connected to the radio-control pushbutton by a brief depression (< 0,4 s) of any of the two pushbutton rockers.

B) > 4 s

1. Depress both rockers of the radio-control pushbutton at the same time for abt. 4 seconds (fig. B: double-sided operation) to switch over to the programming mode. The programming mode is active for abt. 1 minute and confirmed by an intermittent tone (fig. C).

c) ↑

Programming a channel

Depress the channel key for more than 1 second.

Programming a lightscape key

Depress the lightscape key for more than 3 seconds.

Programming a detector

Remove the battery for about 2 minutes from the detector. Put the battery back in place and make a movement inside the detection range of the detector within the next 15 minutes.

Programming a presence detector or a light sensor

Remove the battery(ies) for about 2 minutes from the transmitter. After putting the battery back in place, the device starts transmitting programming telegrams for about 30 s.

Important:

It is not possible to program a combination consisting of presence-control detector, light sensor and detector.

1. The radio-control pushbutton confirms storage of the data transmitted by a continuous tone (Fig. E).

1 min t

Radio Management Radio push button

Ref.-no.: ...1561.07 F...

Deleting all radio-control transmitters

It is possible to delete all transmitters in the radio pushbutton. In this case, the radio pushbutton is reset to the state as delivered.

G) > 20s

Short depression of pushbutton (ε 0,4 s)

When the radio-control pushbutton is attached to an insert permitting the dimming function, the brightness of the lamps connected can be increased (upper rocker) and decreased (lower rocker) by a long depression of the pushbutton rockers.

Important

To switch on the lamps at minimum brightness, depress the lower rocker for more than 4 seconds when the lamps are off.

Illustration of a hand pointing at a light bulb above a screen, with no text or symbols present.

Memory function

The selected brightness level can be stored as memory value in the radio-control pushbutton. A brief depression of the pushbutton recalls the

Important

• In as-delivered condition, the memory value is set to maximum brightness.
• A saved memory value is not lost after a mains failure.

Lightscape

Before storing or recalling a lightscape, the lightscape key of the radio-control transmitter must be programmed into the radio-control pushbutton (see „Programming of a radio transmitter“). The data pertaining to a lightscape (brightness of lamp) can then be stored in the radio-control pushbutton. A lightscape can be changed at any time by storing it again.

Storing a lightscape

1. Select the desired brightness of the lamp.
2. Depress the lightscape key of the radio transmitter for at least 3 seconds. The old lightscape will at first be recalled (keep key depressed). The new lightscape will activated and stored only after about 3 seconds and short tone signal is heard.

6. Radio Transmission

Radio transmission takes place on a non-exclusive path. Therefore, interference cannot be excluded. This type of radio transmission is not suitable for safety applications such as emergency stops or emergency calls. The range of a radio-control system depends on transmitter power, receiver characteristics, air humidity, fitting height and building conditions.

Fig. I illustrates the penetration of building materials by radio waves

Dry material	Permeability
Timber, gypsum, gypsum-plasterboards	approx. 90 %
Brickwork, particle boards	approx. 70 %
Reinforced concrete	approx. 30 %

Radio operation

• The inter-connection of this radio system with other communication networks must comply with national legislation.
• This radio system must not be used for communication beyond property boundaries.
• If utilized in conformity with its designated use, this unit fulfils the requirements of the R&TTE Directive (1999/5/EC). The complete declaration of conformity can be found in the Internet under: www.jung.de/ce

The radio-control pushbutton may be operated in all countries of the EU and the EFTA.

7. Specifications

Power supply : from flush-mounting insert

Receive frequency : 433,42 MHz, ASK

Number of radio channels : 30

Temperature range : approx. 0 °C ... +55 °C

Technical specifications subject to change.

Please hand these instructions over to the customer after the installation.

8. Guarantee

Our products are under guarantee within the scope of the statutory provisions.

Please return the unit postage paid to our central service department