SSK-RAP4DRV2 - Audio accessory Soundskins - Free user manual and instructions

USER MANUAL SSK-RAP4DRV2 Soundskins

Truck Door Kit Instructions

Tools needed for installation:

• Screw driver
• Panel tool

• Microfiber cloth

• Acetone or cleaning solution

• Razor blade
• Roller

Woman adjusting a car interior panel, no visible text or symbols

1. Start by locating the fastening hardware on the door panel, take the appropriate screw driver and remove.

Back view of a person in a car seat, viewed from behind, with hands adjusting the back (no visible text or symbols)

1. Once all the screws are removed you can take off the door panel using a panel tool. Be sure to not break any of the clips or mounting hardware. Pull panel away slowly and unplug any electrical connections.

Interior view of a white car door frame with visible mechanical components and wiring (no text or symbols)

1. Now you are ready to prep the metal surface using a microfiber cloth, Acetone (use a breathing mask), and wipe away any moisture, oil, debris or etc. Then let air dry for an appropriate time. The point is to get the surface clean to ensure material glue contact.

Woman adjusting a car interior panel with a digital display (no visible text or symbols)

1. When the surface is dry and clean, locate the piece of the kit with the label on the back that coincides with the door you're working on. Make sure it lines up correctly before you pull the backing off. After you confirm the right piece, pull off the backing paper and apply the material at the top and working your way down with a roller. Make sure the material is pushed down completely and that no air is trapped. Use a razor blade point or household needle to release air. Repeat these steps for all door panels.

soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins soundkins woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings woodings

1. Press down firmly onto the area where your car speaker hole is, and feel for the speaker wire. Use a razor blade to cut around the speaker hole, being careful to not cut the wire harness. Take the piece you just cut out and stick it behind the speaker hole on the outer door skin to act as a backwave. Score the area where the wire harness is with your blade and tuck the harness between the two flaps. Plug in your speaker.

Person in a dark T-shirt with 'thinkoutside' logo, interacting with a black vehicle interior (no visible text or symbols on the vehicle itself)

1. Now you are ready to place the door panel back on your door. All necessary openings will be available after you have applied the SoundSkins material. Secure door panel with all screws and you are now ready to hit the road!

Soundskins USA 13452 Alondra Blvd, Cerritos, Ca 90703 Phone: [phone] Email: [e-mail] www.SoundSkinsGlobal.com

SKU: SSK-RAP4DRV2

soundskins

RAPTOR

2021+

4 Piece Custom Cut PRO KIT

INSTALLATION VIDEO

Scan code for "how to" video!

Recommended Installation Instructions

A. Prepping the Surface

After removing interior door panels, you are ready to clean the metal areas that will be insulated. If the metal has “new” look without imperfections, then take a microfiber cloth and wipe away any dust and debris. If the metal is showing signs of age like rust, we recommend using Acetone with a breathing mask to wipe off debris and loose particles. A shop vacuum might be needed to remove loose debris on the floorboard.

B. Installing Panels

Now that you have a clean surface, you are ready to start applying the sheets. We recommend using a roller to release air pockets that might be lingering from trapped air. You want to make sure that you have rolled those out to the edge and all the material has a good seal to the metal surface. Make sure all pieces are installed and inspected before reinstalling the interior.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100

2

Top-down line drawing of a car viewed from the side, showing front and rear views with no text or symbols.

3

Diagram of a car's front view with labeled sound source icons and a central '4' symbol

1) Driver Front Door Panel

2) Driver Rear Door Panel

3) Passenger Front Door Panel

4) Passenger Rear Door Panel