V-CD201HTVQ - Vacuum Cleaner LG - Free user manual and instructions

USER MANUAL V-CD201HTVQ LG

Model	CK3
Language	ENGLISH
Page	1 6 PAGE	Color(cover/body)	2 / 2
Material Size	Weight 1 0 0 G		1 9 0 * 2 6 0
Date	2 0 0 6 . 0 9.04	Designer	Wangzhenzhong
Part No.	MFL32930801	Description	M A N U A L , 0

W N

Chage Record

No.	Date	Change content	ECO No.		Designer	Confirm
1		drawing realization	ACTT702608 2	2007.04.1	4 SONG1	CUIYT
2		drawing realization	ACTT703604 2	2007.06.0	1 SONG1	CUIYT
3
4
5
6
7
8
9

OWNER'S MANUAL

V-CD201H*

V-CD201N*

V-CD281H*

V-CD281N*

V-CD261H*

V-CD261N*

V-CD241H*

V-CD241N*

V-CD211H*

V-CD211N*

Bagless vacuum cleaner

Abstract black and white circular logo with stylized 'G' and dot (no text or symbols)

LG

Table of contents

Safety Information....3

How to Use....4

Assembling cleaner ....4

Using the cleaning head and Accessory Nozzles....6

Emptying the Dust Chamber 8

Operating the cleaner....9

Cleaning the Filter ....10

Cleaning the Exhaust Filter....11

Troubleshooting....12

Safety Information

Please read the following information, which contains important instructions for

the use and maintenance of the appliance.

This appliance complies with the following EC Directives: -73/23/EEC,

93/68/EEC-Low Voltage Directive-89/336EEC -EMC Directive.

☐ The appliance is not intended for use by young children or infirm persons without supervision.

☐ Young Children should be supervised to ensure that they do not play with appliance.

☐ If the appliance is supplied from a cord extension set or an electrical portable outlet device, the cord extension set on electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture.

☐ Do not use the appliance if the power cord is damaged or faulty.

□ If the power cord is damaged, it must be replaced by an approved LG Electronics Service Centre.

□Always switch the vacuum cleaner off before:

• Emptying the dust chamber.

- Cleaning or changing the filters.

☐ Do not vacuum flammable or explosive substances(liquids or gases).

☐ Do not vacuum hot ash, embers etc. nor sharp objects.

□ Do not vacuum water or other liquids.

☐ Do not unplug by pulling on cord.

□ Use only LG's recommended filters.

□When you vacuum with an attachment appliance that has a rotating brush roller:

- Do not reach into the running brush roller.

☐ The application is not intended for use by young children or infirm persons without supervision.

Thermal protector: This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly shuts off, turn off the switch and unplug the cleaner. Check the cleaner for a possible source of overheating such as a full dust chamber, a blocked hose or clogged filter. If blockage or obstruction is located, remove and wait at least 30 minutes before attempting to use the cleaner. After the 30 minutes period, plug the cleaner back in and turn on the switch. If the cleaner still does not run, please contact your approved LG service centre.

How to Use Assembling Cleaner Fit the large cleaning head into the end of the tube. Spring latch NT** NE** Elbow Telescopic tube HT** HE**

1 The 2 position head (depending on model)

Push telescopic tube into nozzle outlet.

② Telescopic tube (depending on model)

• Press the spring latch to release.
• Pull out the tube to the desired length.
• Release spring latch to lock the tube in position.
• Push telescopic tube into hose handle firmly.

Head Flexible Hose Button Attachment Point HT** HE** NT** NE**

③ Connecting the flexible hose

• Push the end of the head on the flexible hose into the attachment point on the vacuum cleaner.
  • To remove the flexible hose from the vacuum cleaner, press on the button situated on the head, then pull the head out of the vacuum cleaner.

CAUTION

• Suction power may be weakened when insignificant dusts are sucked. In this case, clean the filter.
• Make the dust box empty if dusts are filled to the maximum degree and then clean the filter when it becomes 5 times.

How to Use Using the cleaning head and Accessory Nozzles

Tear the vinyl bag and pull out accessories. Attach the accessory holder onto the telescopic tube. And then, fit the Dusting Brush, Crevice Tool or Upholstery Nozzle onto the accessory holder. Fit the accessory onto the end of the tube.

Illustration of a hand holding a cup and another cup with a downward arrow, enclosed in a dashed circle (no text or symbols)

Illustration of a hand using a vacuum cleaner to clean a car seat (no text or symbols visible)

Upholstery nozzle Dusting brush Crevice tool ② ③

② Dusting Brush
③ Crevice Tool
① Upholstery Nozzle

Upholstery Nozzle is for vacuuming upholstery, mattresses, etc. The thread collectors help to pick up the threads and fluff.

Dusting Brush is for vacuuming picture frames, furniture frames, books and other irregular surfaces. Dusting Brush is also used for cleaning Filters.

Crevice Tool is for vacuuming in those normally hard-to-reach places such as reaching cobwebs, or between the cushions of a sofa.

① ② ③ ④ ⑤ (depending on model)

4 Pedal

Diagram illustrating a mechanical assembly with labeled components and directional arrows, including a dashed circular annotation.

6 Spring latch (depending on model) Spring latch C K

④ The 2 position head (Depending on model)
⑤ When performing usual cleaning. (Depending on model)
⑥ Elbow tube (depending on model)

• The 2 position cleaning head equipped with a pedal which allows you to alter its position according to the type of floor to be cleaned.
- Hard floor position (tiles, parquets floor) Press the pedal to lower brush.
- Carpet or rug position Press the pedal to lift the brush up.

- You can perform cleaning at any place such as corner or narrow crack by utilizing the structure that both sides of the suction hole are leaned back.

Elbow tube is for cleaning under the sofa, table and bed easily.

• Connect the elbow tube to the flexible hose and, connect the telescopic tube to the elbow tube. (You can also connect the telescopic tube to the flexible hose without the elbow tube.)
• If you pull the spring latch, the elbow tube is bended.
• If you stretch the elbow tube, it is returned to its position.

How to Use Emptying the dust chamber

Pleat-shaped internal filter Circle-shaped external filter Dust chamber cap Dust chamber Dust chamber cap Button Dust chamber Plate

Suction power may be weakened when insignificant dusts are sucked. In this case, clean the filter.

• Turn off the vacuum cleaner and unplug it.
• Your vacuum cleaner is equipped with both a dust chamber and a motor filters.
  Press the button and pull the dust chamber forward.
  Remove the dust chamber cap.
  Clean the pleat-shaped and the circle-shaped filters.

• To reinstall the dust chamber, replace the dust chamber cap and push the dust chamber into the tank mount as far as it will go.

• Open the dust chamber cap.

• Remove two plates from the dust chamber.
• Wash both parts with softcloth. Gently rinse both parts under cold running water.

How to Use Operating the cleaner.

Switch button Cord reel button Plug

Suction control switch ② MAX MIN POWER CONTROL FLOOR CARPET SOFA CURTAIN OFF Regulator Open Close

Mechanical assembly diagram showing a hand operating a lever mechanism (no text or symbols present)

① How to Plug in and Use

② Adjusting the Suction level(depending on model)

③ Park System

• Pull out the power cord to the desired length and plug into the socket.
• Push the suction control switch of the hose handle in the direction of the position what you want. (depending on model)
• To stop it, push down the suction control switch in the direction of OFF. (depending on model)
• Press switch button to start the vacuum cleaner. (depending on model)
• To stop it, press the switch button again. (depending on model)

• Press the cord reel button to retract the power cord after use.

• Adjust suction with the suction control switch in the hose handle. (depending on model)
  • The flexible hose handle has
  a manual air flow regulator which allows you to adjust the suction level briefly. (depending on model)

• To store after vacuuming and pause while vacuuming.
- For deposit after vacuuming, for example to move a small piece of furniture or a rug, use the Park system to support the flexible hose and cleaning head.
- Slide the hook on the large cleaning head into the slot on the rear of the dust chamber.

How to Use Cleaning the Filter

graph TD
    A["Button"] --> B["Brush cleaning"]
    B --> C["Close-up of brush cleaning"]
    C --> D["Close-up of brush cleaning"]
    D --> E["Close-up of brush cleaning"]
    E --> F["Close-up of brush cleaning"]
    F --> G["Close-up of brush cleaning"]
    G --> H["Close-up of brush cleaning"]
    H --> I["Close-up of brush cleaning"]
    I --> J["Close-up of brush cleaning"]
    J --> K["Close-up of brush cleaning"]
    K --> L["Close-up of brush cleaning"]
    L --> M["Close-up of brush cleaning"]
    M --> N["Close-up of brush cleaning"]
    N --> O["Close-up of brush cleaning"]
    O --> P["Close-up of brush cleaning"]
    P --> Q["Close-up of brush cleaning"]
    Q --> R["Close-up of brush cleaning"]
    R --> S["Close-up of brush cleaning"]
    S --> T["Close-up of brush cleaning"]
    T --> U["Close-up of brush cleaning"]

The reusable filters are situated under the dust chamber cap and you can use it permanently.

• Press the button and pull the dust chamber forward.
• Open the dust chamber cap.
• Remove the filters by rotating it counter-clockwise.
• Clean the filters with the dusting brush under cold running water.
• Allow the filters to dry in a shaded location for a day.
• Make the dust chamber empty if dusts are filled to the maximum degree and then clean the filter.

WARNING!

Gently rinse both parts separately under a cold running water until the water runs clear. Do not use detergent or a washing machine or dishwasher. Shake off excess water from the filter.

Do not tumble/spindry, microwave or place in oven or on direct heat. Ensure the filter is completely dry.

Re-assemble and place it back in your machine, filter frame. If the filter is damaged, do not place them in the machine.

Please call the Helpline.

Do not use the net-shaped filter separately.

Do not use the wet filter to avoid clogging.

How to Use Cleaning the Exhaust Filter

graph TD
    A["Filter cover"] --> B["Initial state"]
    B --> C["Close-up of wheel, hand, fan, and blade"]
    C --> D["Reinjection of wheel, blade, and blade"]
    D --> E["Discharge into rear wheel"]
    E --> F["Heat dissipation after cooling"]
    F --> G["Final state: Heat dissipation with visible heat dissipation"]

• The exhaust filter is a washable and reusable HEPA filter.
- To change the exhaust filter, remove the filter cover on the body by release hook.
• Pull out the exhaust filter.
- Clean it with cold, running water.
Do Not use the brush
- Using the brush will cause permanent damage and allow dust to bypass the filter.
- Allow exhaust filter to dry in a shaded location for a dry.
• The exhaust filter should be cleaned at least once a year.

User's Guide for Sani Punch Vacuum Nozzle (Option)

Features

This nozzle picks up even dust inside through beating.

The bottom part can be separated to be cleaned.

Since the bottom does not stick to the surface, vacuuming is easy.

How to use

Follow the directions below for proper use.

Assembly

Connect the nozzle to the telescopic tube.

Illustration of a hand holding a tool to press or adjust a device, showing two sequential steps (no text or symbols present)

Use

Set the suction power control switch to MAX POWER before vacuuming.

Depending on the type of bedding, handling may be awkward or it may cause a lot of noise.

If this is the case, adjust the suction power control switch to a lower setting.

If the punch bar does not move, lift the nozzle slightly off the surface.

If it does not move, even after doing this, check if the suction power is too

low or if the nozzle base is clogged with a foreign object.

This Sani Punch nozzle is for effective cleaning of beds and blankets to remove mites and dust.

Effective cleaning

Bed & bla

Bed & blanket

Bulky & heavy blanket
Light blanket & sheet

Diagram showing two mechanical components with directional arrows indicating movement or force (no text or symbols present)

When using on the bed

Lay out the blanket and vacuum it on the bed.

When using on the floor

It is easier to clean a light blanket or sheet by pushing the nozzle in the direction of the arrow. To increase cleaning efficiency for light blankets, lay on top of a bulky blanket and then clean.

User's Guide for Sani Punch Vacuum Nozzle

Cleaning Vacuum Nozzle for Bedding (Option)

For simple cleaning of the vacuum nozzle, detach the Sani Punch nozzle from the telescopic tube and attach the crevice tool to vacuum dust.

Top Bottom

Line drawing of a hand holding a device with a tool, no text or symbols present

Line drawing of a hand using a tool to adjust or install a mechanical component (no text or symbols visible)

Since the vibrator inside is composed of precision parts, never disassemble the body.

Be careful not to let foreign objects clog the air suction part on top of the vacuum nozzle.

Since removal of the punch bar may cause performance problems, do not warp or remove it.

Attach the bottom plate properly before using. Without this bottom plate, it may not function.

Since this vacuum nozzle has been made exclusively for cleaning beds, blankets and upholstery, use it only for these cleaning purposes.

(Using it to clean the floor may result soiling it or a drop in performance, do not use it for such purposes.)

Follow the instruction below for through washing.

(Do not soak the entire body of the vacuum nozzle in water, it may cause the vibrator to malfunction)

graph TD
    A["1: Press the button on the rear side of the vacuum nozzle to separate the bottom plate."] --> B["2: Wipe all the soiled parts of the vacuum nozzle body with a cloth."]
    B --> C["3: Wash the removed bottom plate with water and dry it."]
    C --> D["4: Straighten the punch bar on the lower section."]
    D --> E["5: Insert the attachment projections on bottom plate to the vacuum nozzle grooves."]
    E --> F["6: Push down the tabs to secure."]

Troubleshooting

What to Do If Your Vacuum Cleaner Does Not Work

- Check that the vacuum cleaner is correctly plugged in correctly and that the electrical socket is working.

What to Do When Suction Performance Decreases

• Turn off the vacuum cleaner and unplug it.
• Check the telecsopic tube, flexible hose and cleaning tool for blockages or obstructions.
• Check that the dust chamber is not full. Empty if necessary.
• Check that the motor filter light is not on. Clean the motor filter, if necessary.
• Check that the exhaust filter is not blocked. Clean the exhaust filter, if necessary.
• If you are still experiencing problems, please contact your local service centre.
  To locate your nearest service centre you can visit our web site www.lge.com.au

Notes

Decorative border frame with leaf motifs and dotted lines, no text or symbols present

Notes

Decorative border frame with leaf motifs and dotted lines, no text or symbols present

LG Electronics Inc.