99-5810 - Car accessory Metra - Free user manual and instructions
Find the device manual for free 99-5810 Metra in PDF.
User questions about 99-5810 Metra
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Car accessory in PDF format for free! Find your manual 99-5810 - Metra and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. 99-5810 by Metra.
USER MANUAL 99-5810 Metra
INSTALLATION INSTRUCTIONS FOR PART 99-5810
APPLICATIONS
LINCOLN Town Car 2003-2011
99-5810
KIT FEATURES
• DIN Head Unit Provision with Pocket
• ISO DIN Head Unit Provision with Pocket
KIT COMPONENTS
natural_image
Interior view of a car air conditioning unit with digital display and control buttons (no readable text or symbols)A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate
natural_image
Technical line drawing of a metal enclosure or housing frame with mounting brackets (no text or symbols)B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
- Wiring Harness:
• 70-5520 - Ford harness 2003-up
•70-5521 - Ford amplified harness 2003-up
• Antenna Adapter: Not required
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
- Socket Wrench Set
natural_image
Three different types of mechanical tools or fasteners shown in line drawings (no text or symbols visible)
1-800-221-0932
www.metraonline.com
© COPYRIGHT 2007-2011 METRA ELECTRONICS CORPORATION
TABLE OF CONTENTS
Dash Disassembly
- LINCOLN Town Car 2003-2011 ..... 1
Kit Assembly
- DIN Head Unit Provision with Pocket 2
- ISO DIN Head Unit Provision with Pocket 3
Final Assembly 4
*Note:
Refer also to the instructions included with the aftermarket radio.
text_image
INSTALLER INSTITUTEKNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
LINCOLN TOWN CAR 2003-2011
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
2 Remove (2) 7mm bolts facing upward above instrument cluster/gauges. (Figure A)
3 Carefully unsnap and remove dash panel surrounding radio and instrument cluster/gauges. (Figure B)
text_image
A 0.0 MIL2.9 50 40 30 20 10 8 6 4 2 0 N P R NO 2 T
natural_image
Technical line drawing of a car interior showing dashboard, steering wheel, and dashboard frame (no text or symbols)4 Remove (2) 7mm bolts above clock panel and remove panel). (Figure C)
5 Remove (4) 7mm bolts securing radio.
Continue to kit assembly.
text_image
CDIN HEAD UNIT PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A)
2 Slide the after-market head unit into the cage and secure. (Figure B) Continue to final assembly.
natural_image
Line drawing of a hand using a tool to adjust or install electronic components on a device casing (no text or symbols visible)
natural_image
Technical line drawing of a mechanical device with mounting brackets and control panel (no text or symbols)ISO DIN HEAD UNIT PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
1 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A)
2 Slide the head unit into the radio opening until the side clips engage. (Figure B)
3 Snap the Trim plate into the Radio Housing. (Figure B)
Continue to final assembly.
natural_image
Line drawing of a hand using a screwdriver to adjust or install an electronic device (no text or symbols present)
text_image
B RIGHT SIDE CLIPFINAL ASSEMBLY
text_image
A B C D(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc ....Red
12V Batt / Memory.....Yellow
Ground. .... Black*
Power Antenna. . . . . . . . Blue
Amp Turn-On .... Blue / White
Amp Ground..... Black / White
Illumination ..... Orange
Dimmer ..... Orange / White
Right Front (+) ..... Gray
Right Front (-)..... Gray/ Black
Left Front (+) ..... White
Left Front (-)..... White / Black
Right Rear (+)....Violet
Right Rear (-) ..... Violet / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer's specifications.
99-5810 INSTRUCTIONS