GB-580F - Smartwatch GLOBALSAT - Free user manual and instructions

USER MANUAL GB-580F GLOBALSAT

GPS Cycle Computer Device

GB-580

User Manual

Version 2.0

BioPORT TIME ALTITUDE 00:00:15 21 m HR SPEED 172 bpm 25.00 kph DISTANCE 100 m SBOP BIOS COMPUTER GPS

Table of Content

1. Introduction and Features......4

1.1 Introduction ...... 4
1.2 Features....4
1.3 Heart Rate Sensor Installation Procedure (Only for GB-580P) 4
1.4 Speed Sensor Installation Procedure (Only for GB-580P) 6
1.5 Cadence Sensor Installation Procedure 9

2. Specifications.... 11

3. Main Menu 14

4. Symbol Explanation.... 16

5. Antenna Introduction.... 17

6. Getting Started....17

6.1 Starting Up Your GB-580 17
6.2 Battery Charging Description.... 18

7. Change The Page.... 19

7.1 Switch different modes 19
7.2 Setting Modes....20

8. Activity 20

8.1 Activity Info....20
8.2 Setting....21
8.3 Trainer....24

9 Navigation 28

9.1 ADD MAP MODE / REMOVE MAP MODE....28
9.2 Remove Compass 28
9.3 Routes....28
9.4 Save Waypoint....30
9.5 Find Waypoint....30
9.6 Back To Start /Stop GOTO....31

10. Connect To PC 32

11. Configuration....32

11.1 User Profile 32
11.2 Page Setting....32
11.3 Set System....33
11.4 Accessories....35

11.5 GPS Settings....38
11.6 Factory Reset....39
11.7 System Upgrade 39
11.8 About Product 39

12. Troubleshooting....39

Thank you for purchasing GB-580. We sincerely hope you to enjoy using this high technology GPS device. For fully understand the functions and features of GB-580, please read the user manual before you get started.

1. Introduction and Features

1.1 Introduction

GPS cycling computer for cyclist usage will provide more analysis ability in this platform. Use barometer to support GPS on virtual statistics and atmosphere changes. Cycling enthusiast can monitor the slope changes with map trace and altitude reading on the analysis application. For enthusiast, GB-580 will also provide accurate training information like pressure, slope, heart rate, cadence, more advanced features, etc. Enthusiast will have more fun while in training with this device. Indeed, for GB-580P model, it embedded pressure sensor, 2.4GHz ANT protocol and electrical compass. Enthusiast can upon personal preference to configure device to achieve their target of training performance.

1.2 Features

The main features of GB-580:

• Slim type compact and watch design
  ● Built-in SiRF Star III LPx high performance GPS chipset.
  ● High resolution display embedded, which performs distinct display at outdoor without backlight.
• Auto Zoom in/ out and auto orientation in guiding mode for easy operation.
  ● Auto calibration algorithm of altitude by GPS without any complicated process.
  ● Trainer mode: To provide different challenge modes to train themselves to improve performance.
  ● Smart Tack Back to guide enthusiast without getting lost.
  ● PC software to provide professional statistic analysis to improve performance.
  ● Support clock mode and alarm function as TOD application.
  ● Built in rechargeable Li-ion poly battery
  ● Over 18 hours in operation
  ● Support self training, route navigation and smart track back.
• Embedded ANT 2.4GHz protocol which supports heart rate belt, cadence and speed sensor. (GB-580P)
• Embedded electrical compass and high accuracy pressure sensor. (GB-580P)

1.3 Heart Rate Sensor Installation Procedure (Only for GB-580P)

Wear the Heart Rate Monitor

Cross-sectional view of a cylindrical object with internal oval and rectangular features (no text or symbols)

Outer side

Heart rate sensor Transmitter Heart rate sensor

Inner side

Moisten this side to your skin. You can wet the sensor to obtain a better reception of your pulse.

1. Put one end of the strap through the slot of the heart rate monitor first.
2. Wrap the heart rate monitor and strap around your chest. Adjust the heart rate monitor to be at the center of your chest.
3. Adjust the strap to fit your chest and make it tight enough to prevent dropping while you are jogging.
4. Put another end of the strap through the slot of the heart rate monitor to finish the wearing.

3D rendered mechanical component with curved and circular features (no text or symbols)

3D rendered mechanical component with a central oval feature and two rectangular ends (no text or symbols)

Illustration of a person's torso wearing a black-and-white chest belt, hands adjusting the belt (no text or symbols)

1. Remember to select "scan" to paring heart rate monitor with your GB-580.

[MAIN MENU] > [CONFIGURATION] > [ACCESSORIES]

[SENSORS] > [HEART RATE] > SCAN.

It will show HR instead of SCAN once paring was finished.

SENSORS HEART RATE SPEED CADENCE SPEED/CADENCE NO NO SCAN NO 15:15

1.4 Speed Sensor Installation Procedure (Only for GB-580P)

1. Parts content list
   

Diagram showing a door handle and two vertical bars with square end caps, plus a plus sign (no text or symbols)

1. 

Illustration of hands using a tool to adjust or install a plug into a socket (no text or symbols present)

1. 

Line drawing of hands adjusting a mechanical component with red clamps (no text or symbols)

1. 

Silicon Rubber

1. The edge of magnet should be on the arrow

Diagram showing a mechanical or electrical component with labeled parts and directional arrows, including a red circular symbol with a plus sign.

In order to achieve the necessary 12mm or less install the transmitter and the magnet closer to the wheel hub

Max. 12mm

1. The image of sensor mount on the wheel

Diagram of a bicycle wheel with a red arrow indicating rotational motion (no text or symbols)

7.

Max.30 Max.150cm

1. Press button

Hand inserting a red triangular component into a device (no text or symbols visible)

Green LED turn on 2 sec and also the LED will blinking for the first 10 times after sensor detect magnetic

Simple line drawing of a door with a triangular head and red warning symbol (no text or labels)

1. Remember to select "scan" to paring speed sensor with your GB-580. It will show SP instead of SCAN once paring was finished.

[MAIN MENU] > [CONFIGURATION] > [ACCESSORIES]

[SENSORS] > [SPEED] > SCAN.

SENSORS HEART RATE SPEED CADENCE SPEED/CADENCE NO NO SCAN 15:21

Replace and change battery

Replace a new Battery

1.5 Cadence Sensor Installation Procedure (Only for GB-580P)

1. Parts content list
   

Simple line drawing of a computer monitor with an upward arrow and plus signs, next to two vertical bars (no text or symbols)

1. 

Diagram showing two hand positions with red arrows indicating movement or force, possibly illustrating a mechanical or electrical process.

1. 

Move

1. 

Diagram showing a mechanical device with two components and a red arrow indicating motion (no text or symbols)

1. 

Illustration of a hand using a tool to adjust a mechanical component (no text or symbols present)

1. The edge of magnet should be on the arrow
   

Umax. 1.2mm

1. 

Max.150cm Max.30

1. Press button

CARDIOSPORT

Green LED turn on 2 sec and also the LED will blinking for the first 10 times after sensor detect magnetic

CARDIOSPORT

1. Remember to select "scan" to paring speed sensor with your GB-580. It will show CA instead of SCAN once paring was finished.

[MAIN MENU] > [CONFIGURATION] > [ACCESSORIES]

[SENSORS] > [CADENCE] > SCAN.

SENSORS HEART RATE NO SPEED NO CADENCE NO SPEED/CADENCE NO SCAN 15:24

Replace and change battery

Diagram illustrating the step-by-step installation of a mechanical component, showing tool application and rotation direction.

Replace a new Battery

1. Specifications

Electrical and Mechanical Parameters General
Number of Waypoint 100	100
LAP	6000
Number of Track point 60000	60000
Display Size	Active Area : 29.94 * 32.75View Area : 32.34 * 34.85(H x W in mm.)	Active Area : 29.94 * 32.75View Area : 32.34 * 34.85(H x W in mm.)
Display type 4 Grayscales colors 4 Grayscales colors
Resolution 128x128 Pixels 128x128 Pixels
Waterproof Standard IPX7		IPX7
Unit Size	70 x 49 x 18 (L x W x H in mm.)	70 x 49 x 18 (L x W x H in mm.)
Backlight Display	Single level	Single level
Operating temperature	-10°C to 60 °C	-10°C to 60 °C
Humidity	5% to 95% Non-condensing	5% to 95% Non-condensing
Voltage	3.7V for a rechargeable battery	3.7V for a rechargeable battery
Battery	Rechargeable 760mAhLithium ion battery	Rechargeable 760mAhLithium ion battery
Battery life	GPS 3D fix, Backlight off - 18 hoursGPS 3D fix, Backlight on - 14 hrs	GPS 3D fix, Backlight off - 18 hoursGPS 3D fix, Backlight on - 14 hrs
Barometer	N/A	+/-1.5mbar
E-Compass	N/A	2 Axis +/-5 degree
2.4G RF	N/A	ANT+ Sport Protocol, 3m transmission distance
Interface	Mini USB	Mini USB
GPS Parameters General
GPS Chipset:	20 Channel
Frequency:	L1, 1575.42 MHz
Code:	C/A code
Channels:	48 Acquisition and 12 Tracking
Antenna Type:	Built-in patch antenna
Position:	2.2m CEP without DGPS
Velocity:	0.1 m/s
Time:	1 us synchronized to GPS time
Default datum:	WGS-84
Reacquisition:	0.1 sec., average

6000

Hot start:	1.5 sec., average
Warm start:	32 sec., average
Cold start:	34 sec., average
Altitude:	18,000 meters (60,000 feet) max.
Velocity:	515 meters/ second (1000 knots) max.
Acceleration:	Less than 4g

Power / Light/ Esc Up/ Start/ Stop ISPORT TIME ALTITUDE 00:00:15 21 m HR SPEED 172 bpm 25.00 kph DISTANCE 100 m SBOP SAVE COMPUTER GPS Page/ Enter Down/Lap/Save

Button Description
Power/ESC Press 2 seconds to turn on/off GB-580.When GB-580 is on, quickly press this button will turn on/off the backlight.Press and hold this button for 14 seconds to do hardware reset if the system is halted.In Menu mode, press ESC button shortly to escape from the current page and go back to the previous page.
PG /ENTER Switch between the screens of Speedometer mode.Press 2 seconds to enter between Main Menu page Speedometer Page alternatively.In Main Menu page, press this button shortly as ENTER function.Switch between the screens of “Menu mode”, “Location mode”, “Speedometer mode” and “Map mode”.
Up /Start/Stop	To press UP to up scrolling as highlighting an item in Main Menu page.In Speedometer mode, press START button to start timer to get training.In Speedometer mode, press STOP button to stop timer in training.In Map mode, press for zoom in.
Down/Lap/Save	To press Down to down scrolling as highlighting an item in Main Menu page.In Speedometer mode, when timer is counting for training, press Lap button to create a lap.If timer is stop while in training, press SAVE button to save training.

3. Main Menu

This diagram presents all the available menu options for your quick look up.

ACTIVITY	ACTIVITY INFO	TRAINING INFO
		DELETE ALL
	SETTING	AUTO HOLD
		ALERTS	TIME/DIST ALERT
			SPEED/PACE ALERT
			HEART RATE ALERT
			CADENCE
			SETTING
		CALORIES	SPORT TYPE
			TRANING LEVEL
			EXTRA WEIGHT
		LAP SETTING
		DATA RECORDING
	TRAINER	DIST / TIME
		DIST / SPEED
		SPEED / TIME
		RACE/ DIST
		YOURSELF
	MEMORY STATUS
NAVIGATION	ADD MAP MODE / REMOVE MAP MODE
	REMOVE COMPAS / ADD E-COMPASS
	ROUTES	CREATE NEW
		LIST ALL
		DELETE ALL
	SAVE WAYPOINT
	FIND WAYPOINT	LIST ALL
		DELETE ALL
	BACK TO START / STOP GOTO
CONNECT TO PC

CONFIGURATION
CONFIGURATION	USER PROFILE
	PAGE SETTING	SET PAGE 1
		SET PAGE 2
		SET PAGE 3
		SET PAGE 4
		SET LAP PAGE
	SET SYSTEM	BEEPER
		TOD MODE
		DISPLAY	BACKLIGHT
			LANGUAGE
			ORIENTATION
			UNITS
		TIME SETTINGS TIME FORMAT
			TIME ZONE
			DAYLIGHT
		ALARM	FREQUENCY
			TIME
	ACCESSORIES	SENSORS*	HEART RATE*
			SPEED*
			CADENCE*
			SPEED/CADENCE*
		CARDIO SETTING*
		BIKE SETTING*	BIKE*
			WEIGHT*
			WHEEL SIZE*
		BARO SETTING*	CALBRATION*
			SEA LEVEL PRESSURE*
			CURRENT ALTITUDE*
		SET COMPASS*	CALIBRATION*
			DECLINATION*
			FOLLOW BEARING*
	GPS SETTINGS	WAAS / EGNOS
		GPS
		GPS INFO
	MAP MODE SET	BIRD EYE VIEW/ DIRECT TO NORTH
		ZOOM IN / OUT
	FACTORY RESET

	SYSTEM UPGRADE
	ABOUT PRODUCT

Note: * is only available for P model

4. Symbol Explanation

MENU ACTIVITY NAVIGATION CONNECT TO PC CONFIGURATION

Icon picture Description Indication
	GPS status	GPS status indicator■ Flash: No signal■ Solid: 3D fix■ Solid with 1 bar: 3D fix with poor signal■ Solid with 2 bar: 3D fix with good signal■ Solid with 3 bar: 3D fix with strong signal
	timer icon	When training is active, the icon will appear. When you stop the timer, the icon will be flashing.
[CAT0]	Cadence sensor	This icon will show up when device scanning the cadence / speed sensor
[IOHH]	Clock alert	This icon will show up when you set the alarm clock for WEEKEND, WEEKDAY, DAILY...or OFF
[2DKC]	Heart rate monitor indication	This icon will show up when device scanning the heart rate monitor
	Battery capacity indication	The remaining battery power

5. Antenna Introduction

600 TIME ALTITUDE 00:00:15 21 m HR SPEED 172 bpm 25.00 mph DISTANCE 100 m SBOP BAG COMPETION GPS

The GPS antenna is located in the lower part of the device. Let it face to the sky for a better reception.

6. Getting Started

6.1 Starting Up Your GB-580

Press the Power button for 2 seconds to turn on the device. You will see the welcome screen displayed. Allow the GB-580 a short time to track satellites for the first time you use it. Take your GB-580 to the outdoor open space with a clear view to the sky and it will be easy to acquire satellite signal with a few seconds. If the device can't get 3D fixed, you can still press PG button to exit the Locating screen. System will pop up "RESET GPS" to ask you perform cold start if can't get 3D fix for 3 minutes. To turn off your GB-580, press the Power button for 2 seconds. If the system frozen, press power button for 10 seconds to do hardware reset.

SPORT GB-580P COPYRIGHT BY GLOBALSAT

Locating Satellites... 00/4 FIXED

6.2 Battery Charging Description

GB-580 operates by a built-in Li-ion rechargeable battery.

A battery icon shown on the left bottom corner of screen indicates the remaining battery power.

To charge the battery:

Connect one end of USB clip with your GB-580 and the other end with the AC adapter or USB port on PC.

TIME OF DAY 2011/03/03 11:06:53PM THU 11:06PM

7. Change the Page

7.1 Switch different modes

Short press "Page/OK" to switch different modes

graph TD
    A["Locating Satellites... 00/4 FIXED"] --> B["TIME 00:00:00 HR ALTITUDE 0 m"]
    B --> C["Custom Page1"]
    C --> D["TIME 00:00:014 HR START ALTITUDE 3 m"]
    D --> E["In Speedometer mode, press to Start or Pause timer"]
    E --> F["SPEED 00.00 kph DISTANCE 0 m TIME 00:00:00"]
    F --> G["Custom Page2"]
    G --> H["TIME OF DAY 2011/03/03 11:06:53P THU 11:06PM"]
    H --> I["CUMULATE+ Asc SPEED --.--m 0mph CUMULATE- ALTITUDE --.--m 0 m DISTANCE 0 m"]
    I --> J["Custom Page 4"]
    J --> K["CALORIES PACE 0.00Cal --:--/km SPEED 00.00 kph SLOPE 0 %"]

7.2 Setting Modes

Long press "PG/OK" around 2 seconds to enter setting modes and "ESC" to back to Speedometer mode or TOD mode.

TIME OF DAY 2011/03/03 11:06:53PM THU 11:06PM

PG/OK 2seconds ESC

MENU ACTIVITY NAVIGATION CONNECT TO PC CONFIGURATION T 01:53AM

8. Activity

8.1 Activity Info

8.1.1 Training Info

[[ACTIVITY] > [ACTIVITY INFO] > [TRAINING INFO]

1. Use Up and Down button to scroll to the item you wish to display and press "OK" button then all training data information will display:
2. Use Up and Down to select the file you wish to check and press 'OK' button, the training data information is shown on the screen.

Information items are displayed:

• Date and Time.
  ● Total distance of this training.
  ● Total calories you have burned.
  ● Total time of this training.
  ● Average speed of this training.
• Fastest speed of this training.
  ● VIEW? Display this training data on the screen.
• TRACK BACK? You can track back to the BEGIN point or END point of this training route.
  ● LAPS? View the LAP details on map mode.
• DELETE? You can delete this training data.

DAYS 03-MAR 11:58:59PM 1 03-MAR 11:41:29PM 1 03-MAR 11:24:38PM 1 03-MAR 05:59:25AM 3 19-FEB 05:52:05AM 1 00:00:54 160 m 10.63k/h 05:38/km DCa1 Dbpm T 02:09AM

19-FEB-09 05:52:05AM TOTAL: 0 m 0Cal 00:00:04 AVERAGE: 0.00kph --: /km □ bpm □ rpm FASTEST: 0.00kph --: /km □ bpm □ rpm VIEW? TRACK BACK? LAPS? DELETE? T 02:10AM

8.1.2 Delete All

[MAIN MENU] > [ACTIVITY] > [DELETE ALL]

You can delete all the training data stored in the device.

ACTIVITY INFO DELETE ALL TRAINING DATA? YES NO 02:11AM

8.2 Setting

8.2.1 Auto Hold

[MAIN MENU] > [ACTIVITY > [SETTING] > [AUTO HOLD]

1. The Auto Hold function allows you to pause the timer automatically when you stop moving or your speed falls below a certain value.
2. When in the stationary or within the specific speed, the data is not recorded. Thus the average speed and calories calculation could be more accurate.

AUTO TIMER PAUSE OFF OFF WHEN STOPPED CUSTOM SPEED 02:14AM

8.2.2-1 Alerts - Time / Distance

[MAIN MENU] > [ACTIVITY > [ACTIVITY SETTING] > [ALERTS] > [TIME/DIST]

1. Use Up and Down button to select the item and press OK to modify it.
2. You can set the alarm to sound once when the specified time is reached, or repeat to sound on every specified time, or turn it off.
3. You can set the alarm to sound once when you reached the specified distance, or repeat to sound on every specified distance, or turn it off.

TIME ALERT OFF ALERT AT: 00:01:00 DISTANCE ALERT OFF ALERT AT: 0.05 km I 02:16AM

8.2.2-2 Alerts - Speed / Pace

[MAIN MENU] > [ACTIVITY > [ACTIVITY SETTING] > [ALERTS] > [SPEED / PACE]

1. Use Up and Down button to select the item and press OK to modify it.
2. You can set the alarm to sound when your speed or pace is above or below a specified value.

ALERTS SPEED FAST SPEED ALERT OFF ABOVE: 12.87 kph SLOW SPEED ALERT OFF BELOW: 4.83 kph 02:17AM

8.2.2-3 Alerts - Heart Rate (GB-580P only)

[MAIN MENU] > [ACTIVITY > [ACTIVITY SETTING] > [ALERTS] > [HEART RATE]

1. Use Up and Down button to select the item and press OK to modify it.
2. You can set the alarm to sound when your HR ZONE / CUSTOM setting is above or below a specified value or OFF alarm.

ALERT MAX HR AL ON ABOVE: CUSTOM OFF CUSTOM HR ZONE TOJ bpm MIN HR ALERT ON BELOW: 75 bpm *04:08AM ♥

8.2.2-4 Alerts – Cadence (GB-580P only)

[MAIN MENU] > [ACTIVITY > [ACTIVITY SETTING] > [ALERTS] > [CADENCE]

1. Use Up and Down button to select the item and press OK to modify it.
2. You can set the alarm to sound on or off when your cadence is above or below a specified value.

HIGH CAD ALERT OFF ABOVE: 120 rpm LOW CAD ALERT OFF BELOW: 70 rpm T 02:20AM

8.2.2-5 Setting

You can choose the alerts methods as message/beeper or symbol/beeper

ALERTS MESSAGE/BEEPER MESSAGE/BEEPER SYMBOL/BEEPER 02:21AM

8.2.3 Calories

[MAIN MENU] > [ACTIVITY] > [SETTING] > [CALORIES]

- Sport Type

Select sport type from "Walking", "Hiking", "Running",

"Biking" or "By Time" by press UP and Down button.

To set the type in order to come out more accurate result.

- Training Level

Select training level depend on your personal condition and exercise strength, the default setting is Middle. To set the level in order to come out more accurate result.

- Extra Weight

Confirm the extra weight you carry and then input to EXTRA WEIGHT item. To set the value in order to come out more accurate result.

System will calculate the calories consumption depending on the specified sport type.

SPORT TYPE BIKING TRAINING LEVEL MIDDLE EXTRA WEIGHT 0 kg I 02:23AM

SPORT TYPE BIKING TRAINING LE MIDDLE EXTRA WEIGHT kg 02:23AM

SPORT TYPE BIKING TRAINING LE MIDDLE EXTRA WEIGH kg 04:16AM ♥

8.2.4 Lap Setting

AIN MENU] > [ACTIVITY] > [SETTING] > [LAP SETTING]

You can select LAP trigger "by Distance" or "by Time"

AUTO LAP TRIGGER OFF OFF DISTANCE BY TIME 02:25AM

8.2.5 Data Recording

[MAIN MENU] > [ACTIVITY] > [ACTIVITY SETTING] > [DATA RECORDING]

- Record Data Points

System is default to record one point for every second. This will create the most accurate record for your training activity. However, you can set a different interval to record the points.

RECORD DATA POINTS CUSTOM TIME R I EVERY SECOND CUSTOM TIME INDOOR TRAINING R points: 60006 TIME: 33hr20min12s ALTITUDE SET BAROMETER 02:29AM

● Recording Interval Setting

You may base on different sport and strength to set the interval. In this way, you may get more accurate information for analysis and more stable to control Auto Zoom In and Out while in Track Back. The recommended values is:

- Walking and Running: 1s

- Cycling: 2s

● Altitude Set (GB-580P only)

Choose the information of altitude form GPS or Barometer sensor. It is recommended using barometer to get much reliable altitude information. Be aware of calibrating the pressure sensor before training.

RECORD DATA POINTS CUSTOM TIME RECORD EVERY Remain sec points: 6000 TIME: 33hr20 ALTITUDE SE BAROMETER 02:27AM

RECORD DATA POINTS CUSTOM TIME RECORD EVERY Remain 2 sec points: 60006 T FROM GPS A1 BAROMETER BAROMETER 02:20AM

8.3 Trainer

8.3.1 Dist / Time

[MAIN MENU] > [ACTIVITY] > [TRAINER] > [DIST/TIME]

Set distance for 3 km and time for 15 minutes which means the virtual trainer will finish 3km within 15 minutes to compete with you.

1. You could change DIST / TIME to set up your goal.

2. Finished setting, press "Up or Down button" to select "Start" and then press "Enter button" to start.

3. ENABLE ALERT ? you can select YES or NO to give you a alert.

4. DO YOU RECORD RUNNING DATE ? If select YES the chronograph will start to record your training.

5. When you reach your goal or have superior or poor performance to trainer, it will show good job / do harder next time

6. If you have superior or poor performance to trainer, it will show ahead or behind distance to you.

DIST/TIME REST DIST 10.000km REST TIME 00:05:00 START T 02:36AM

DIST/TIME ENABLE ALERT? YES NO 00:05:00 START 02:42AM

DIST/TIME DO YOU RECORD RUNNING DATA? YES NO 00:05:00 START

DIST/TIME BEST DIST BEHIND 2.674km 00:03:18

DIST/TIME BEST DIST AHEAD 414 m NEXT TIME 01:03:02 *16:27

8.3.2 Dist / Speed

[MAIN MENU] > [ACTIVITY] > [TRAINER] > [DIST/SPEED]

Set distance for 10 km and speed for 10 km/hr which means trainer will keep 10km/hr running for 10km to race with you.

1. You could change DIST / SPEED to set up your goal.
2. Finished setting, press "Up or Down button" to select "Start" and then press "Enter button" to start.
3. ENABLE ALERT ? you can select YES or NO to give you a alert.
4. DO YOU RECORD RUNNING DATE ? If select YES the chronograph will start to record your training.
5. When you reach your goal or have superior or poor performance to trainer, it will show ahead or behind distance to you.

DIST/SPEED REST DIST 10.000km SPEED 10.00kph START 02:46AM

DIST/SPEED ENABLE ALERT? YES NO 10.00 kph START 02:45AM

DIST/SPEED DO YOU RECORD RUNNING DATA? YES NO 10.00 kph START 03:16AM

DIST/SPEED BEST DIST BEHIND 243 m 10.00 kph

DIST/SPEED BEST DIST AHEAD 274 m 10.00 kph START I 16:29 ♥

8.3.3 Speed / Time

[MAIN MENU] > [ACTIVITY] > [TRAINER] > [SPEED /TIME]

Set speed 10km/hr and time 00:05:00 means trainer will keep 10km/hr running for 5mins to race with you.

1. You could change SPEED / TIME to set up your goal.
2. Finished setting, press "Up or Down button" to select "Start" and then press "Enter button" to start.
3. ENABLE ALERT ? you can select YES or NO to give you a alert.
4. DO YOU RECORD RUNNING DATE ? If select YES the chronograph will start to record your training.
5. When you reach your goal or have superior or poor performance to trainer, it will show ahead or behind distance to you.

SPEED/TIME REST TIME 00:05:00 SPEED 10.00 kph START 02:52AM

SPEED/TIME ENABLE ALERT? YES NO 10.00 kph START 02:53AM

SPEED/TIME DO YOU RECORD RUNNING DATA? YES NO 10.00 kph START 03:18AM

SPEED/TIME BEST TIME BEHIND 3.221km SPEED 15.00 kph

SPEED/TIME BEST TIME AHEAD 2.572km 15.00 kph

8.3.4 Pace / Dist.

[MAIN MENU] > [ACTIVITY] > [TRAINER] > [PACE/DIST]

Set dist 10m/hr and pace 00:01:00/km means trainer will keep the specific pace to run 10km to race with you.

1. Yu could change PACE/ DIST to set up your goal.

2. Finished setting, press "Up or Down button" to select "Start" and then press "Enter button" to start.

3. ENABLE ALERT ? you can select YES or NO to give you a alert.

4. DO YOU RECORD RUNNING DATE ? If select YES the chronograph will start to record your training.

When you reach your goal or have superior or poor performance to trainer, it will show ahead or behind distance to you.

PACE/DIST REST DIST 10.000 km PACE 00:01:00 /km START 03:19AM

PACE/DIST ENABLE ALERT? YES NO 00:01:00 / km START I * 03:19AM

PACE/DIST DO YOU RECORD RUNNING DATA? YES NO 00:01:00 / km START

PACE/DIST BEST DIST BEHIND 605 m TIME 00:01:00 /km 16:10

DIST/TIME BEST DIST AHEAD 22 m 00:59:21

8.3.5 Yourself

[MAIN MENU] > [ACTIVITY] > [TRAINER] > [YOURSELF]

Select the previous performance training as workout. Trainer will base on your previous performance to race with you.

List all training information. And select the training as workout to go for training.

DAYS 03-MAR 11:58:59PM 1 03-MAR 11:41:29PM 1 03-MAR 11:24:38PM 1 03-MAR 05:59:25AM 3 19-FEB 05:52:05AM 1 00:00:54 160 m 10.63k/h 05:38/km DCa.l Dbpm T 03:00AM

YOURSELF REST DIST 0.034 km REST TIME 00:00:06 START T 03:08AM

8.3.6 Memory Status

[MAIN MENU] > [ACTIVITY] > [TRAINER] > [MEMORY STATUS]

You will see how many points left and the remaining time you can use. The remaining time depends on the period of your record setting.

ACTIVITY Remain Points are 60006 points Can Record About 33hr20min12sec TRAINER MEMORY STATUS 03:02AM

9 Navigation

9.1 ADD MAP MODE / REMOVE MAP MODE

[MAIN MENU] > [NAVIGATION] > [ADD/REMOVE MAP MODE]

You can use this feature to display or not display the map mode. However, while the Map Mode is off, and you execute "Add map code" or "Remove map" a waypoint, the Map Mode will be turn on again.

NAVIGATION ADD MAP MODE REMOVE COMPAS ROUTES SAVE WAYPOINT

NAVIGATION REMOVE MAP REMOVE COMPAS ROUTES SAVE WAYPOINT

9.2 Remove Compass

[MAIN MENU] > [NAVIGATION] > [ADD/REMOVE COMPASS]

You can use this feature to enable or disable compass page. It will show the direction and remain distance to target point and you can follow up to back.

NAVIGATION ADD MAP MODE ADD E-COMPASS ROUTES SAVE WAYPOINT

NAVIGATION ADD MAP MODE REMOVE COMPAS ROUTES SAVE WAYPOINT

9.3 Routes

9.3.1 Create New

[MAIN MENU] > [NAVIGATION] > [ROUTES] > [CREATE NEW]

1. You can add the waypoints to create your own route. Press OK button to insert a waypoint.

2. Highlight a waypoint and press OK button for deleting this waypoint or insert another waypoint in above.

3. In the first line of the screen, you can edit the name of

EMPTY ---- : ---- km DELETE? FOLLOW? 10:55PM

this route. When you are done with editing the route, press ESC button to save and exit.

1. Select "FOLLOW" to get training. It will guide you automatically. You may press "ENTER" or "ESC" to go next or last waypoint

WAYPOINTS A-2 001 002 003 004 005 006 007 11:20PM

006-009 006 _:_ 0 m 007 _:_ 306 m 008 _:_6.840km 009 _:_8.252km : __ km DELETE? FOLLOW? 11:22PM

NE PT102 PT102 50m PT102 55 m 11:25AM ♥

TO BEGIN TO 001 00:03:18 04:18:45 43 m 3.448km

9.3.2 List All

[MAIN MENU] > [NAVIGATION] > [ROUTES] > [LIST ALL]

1. Select the route you want to navigate, and select "FOLLOW?". You will be asked which point (start point or end point) to navigate. You will see your current position and destination point on the screen, and those nearby waypoints are also displayed. Press Up and Down button to zoom out and zoom in the map view. To press" ENTER" or "ESC" will go next or last waypoint.

2. Press PG button display the distance and time for you to reach destination on the right part of screen. The direction of destination waypoint is shown by the arrow sign of the compass.

3. If you want to stop the navigation, press [MAIN MENU] > [NAVIGATION] > [STOP ROUTE]. Select the route you want to delete, and select "DELETE?". This route will be deleted immediately.

ROUTES 001-001 002-002 表 006-009 11:SSPM

50m 001 3.442km 11:21AM

9.3.3 Delete All

[MAIN MENU] > [NAVIGATION] > [ROUTES] > [DELETE ALL]

1. A confirmation dialog box will appear.
2. Use Up and Down button to highlight "YES" and press OK.
3. All routes data in memory will be deleted.

ROUTES DELETE ALL ROUTES DATA? YES NO DELETE ALL 12:02AM

9.4 Save Waypoint

[MAIN MENU] > [NAVIGATION] > [SAVE WAYPOINT]

1. You can save the current position. If the GPS position is fixed, it shows the longitude, latitude and elevation on the screen.
2. Use Up and Down button to scroll to the item you wish to modify and then use the "Enter button" to select and confirm.
3. When you finish the modification, input a "enter sign" character or press the "Esc /Lap button" to exit.
4. Move highlight to "CONFIRM?" and press "Enter button". The location data will be stored in the memory

011 N 24°59.7916' E 121°29.2637' ELEV: 19 m CONFIRM? T: 12:03AM

011 N 24°59.7' E 121°29.2637' ELEV: 19 m CONFIRM? 12:04AM

9.5 Find Waypoint

9.5.1 List All

[MAIN MENU] > [NAVIGATION] > [FIND WAYPOINT] > [LIST ALL]

1. Use Up and Down button to scroll to the Waypoint you wish to go to and press "Enter button".

2. Highlight "GOTO?" item and press "Enter button".

3. You will see your current position and destination

WAYPOINTS A-Z 001 002 003 004 005 006 007 12:07AM

point on the screen, and those nearby waypoints are also displayed.

1. Press "Page button" display the distance and time for you to reach destination on the right part of screen. The direction of destination waypoint is shown by the arrow sign of the compass.

002 N 25°01.2938' E 121°29.9288' ELEV: 31 m GOTO? DELETE? T 12:07AM

50m 001 3.442km 11:21AM ♥

TO BEGIN TO 001 00:03:18 04:18:45 43 m 3.448km

9.5.2 Delete All

[MAIN MENU] > [NAVIGATION] > [FIND WAYPOINT] > [DELETE ALL]

1. A confirmation dialog box will appear.
2. Use Up and Down button to highlight "YES" and press OK.
3. All waypoints in memory will be deleted.

FIND WAYPOINT DELETE ALL WAYPOINT DATA? YES NO 12:09AM

9.6 Back To Start /Stop GOTO

[MAIN MENU] > [NAVIGATION] > [RETURN TO START / STOP GOTO]

1. You can use this feature to navigate you back to the start point of the latest saved training data.
2. The navigation screen is shown and you can follow the direction of arrow to go back to the start point. If you want to stop the navigation, press[MAIN MENU] > [NAVIGATION] > [RETURN TO START / STOP GOTO]

NAVIGATION ROUTES SAVE WAYPOINT FIND WAYPOINT BACK TO START 12:10AM

NAVIGATION ROUTES SAVE WAYPOINT FIND WAYPOINT STOP GOTO 12:10AM

10. Connect To PC

[MAIN MENU] > [CONNECT TO PC]

If wonder to communicate to PC, you may follow the ways:

1. System will pop up message to ask you "Want to connect to PC?" while cable is plugging.
2. Select Connect To PC in Menu Mode for communicating.

You can transfer the training data from GB-580 to your PC.

CONNECT TO PC Waiting for PC to connect...

11 Configuration

11.1 User Profile

[MAIN MENU] > [CONFIGURATION] > [USER PROFILE]

1. You can input your personal information in the user profile for getting more accurate information before training.
2. The data fields include "username", "gender", "birth date", "weight" and "height".
3. The system will do the calories calculation base on the information you provide. Please input the correct value.

USER PROFILE USER NAME USER NAME GENDER MALE BIRTH DATE 1981 / JAN / 1 HEIGHT 68 kg HEIGHT 178 cm Til 12:15AM

11.2 Page Setting

[MAIN MENU] > [CONFIGURATION] > [PAGE SETTING]

1. There are four custom pages and one Lap screen to show training information. You may set your preference for person training.
2. There have five types of screen field could be choose for every page.
3. Select the function coefficient you want then

PAGE SETTING SET PAGE 1 SET PAGE 2 SET PAGE 3 SET PAGE 4 Tel 12:15AM

press 'Enter button" to save setting.

1. To select what information you want to show on the display for your training record.

CHOOSE FIELD NO. SET PAGE 4 T: 12:16AM CUMULATE+ Asc SPEED -- . -- m 24mph CUMULATE - ALTITUDE -- . -- m 20m DISTANCE 0 m CAL RATE CALORIES CUMULATE+ CUMULATE- DISTANCE 0 24mph CUMULATE- DISTANCE 0 24mph DISTANCE 0 m

11.3 Set System

11.3.1 Beeper

[MAIN MENU] > [CONFIGURATION] > [SET SYSTEM] > [BEEPER]

You can set beeper on or off and accompany message only or both of KEY sound and Message.

SET SYSTEM BEEPER KEY AND MESSAGE TO OFF MESSAGE ONLY DI KEY AND MESSAGE TIME SETTINGS ALARM 12:19AM

11.3.2 TOD Mode

[MAIN MENU] > [CONFIGURATION] > [SET SYSTEM] > [TOD MODE]

You can choose OFF, 5 minutes, 10 minutes. System will enter to TOD mode as clock while standby over the specific time.

In TOD mode, you may press UP for 2 seconds to escape to normal operation mode.

TOD MODE STAND BY OFF 12:20AM

11.3.3 Display

[MAIN MENU] > [CONFIGURATION] > [SET SYSTEM] > [DISPLAY]

- Backlight

Set the backlight to stay on or automatically turn off after a period of time once you press Power button to activate the backlight.

DISPLAY BACKLIGHT 15 SECONDS LAN STAYS ON 15 SECONDS 30 SECONDS ORII 1 MINUTE 2 MINUTES UNITS 12:21AM

- Language

There are 5 different languages of User Interface, including "English", "Spanish", "Italian", "French" and "Germany".

ENGLISH ESPAÇOL ITALIANO FRANÇAIS BACI LAN ENGLISH ORIENTATION VERTICAL UNITS 12:22AM

- Orientation

Choose orientation with vertical or horizontal. This feature is upon personal preference for easy reading while in activity. You also may follow the combination key "PG+DOWN" to rotate screen.

DISPLAY BACKLIGHT 15 SECONDS LANGUAGE ORI VERTICAL HORIZONTAL VERTICAL UNITS 12:22AM

- Units

1. The measurement unit can be set as "statute" or "metric".
2. The speed unit can be set as Pace (min/m, min/K) or Speed (mph, kph).

UNIT SETTINGS UNIT METRIC ( m,kph ) COORDINATION DEFAULT(Deg"Min") UNIT DEFAULT(Deg"Min") GOOGLE(D"M'S") UTM(X"Y") DEFAULT(Deg"Min") 12:23AM 12:25AM

11.3.4 Time Settings

[MAIN MENU] > [CONFIGURATION] > [SET SYSTEM] > [TIME SETTINGS]

- Time Format

1. Use Up and Down button to scroll to the item and press OK to modify it.
2. You can set the time to display in the 12 Hour or 24 hour format.

TIME SETTINGS TIME FORMAT 12 HOUR TIME 12 HOUR 24 HOUR DAYLIGHT SAVING OFF 12:26AM

- Time Zone

1. Use Up and Down button to scroll to the item and press OK to modify it.
2. You can select your local time zone.

Tehran Tokyo US-Alaska US-Arizona US-Atlantic US-Atlantic DAYLIGHT SAVING OFF 12:26AM

- Daylight Saving

1. Use Up and Down button to scroll to the item and press OK to modify it.
2. You can select the daylight saving if necessary, and then system will display the correct time for you.

TIME SETTINGS TIME FORMAT 12 HOUR TIME ZONE OFF ANIC DAY ON SAVING OFF 12:27AM

11.3.5 Alarm

[MAIN MENU] > [CONFIGURATION] > [SET SYSTEM] > [ALARM]

You can set the alarm clock for WEEKEND, WEEKDAY, DAILY...or OFF. And then set up the time you want clock to ring you.

ALARM FREQUENCY OFF THU FRI SAT WEEKDAY WEEKEND DAILY OFF TIME 12:28AM

ALARM FREQUENCY OFF AM TIME PM 12:00 AM T 12:29AM

11.4 Accessories (GB-580P only)

11.4.1 Sensors

[MAIN MENU] > [CONFIGURATION] > [ACCESSORIES] > [SENSORS]

1. Use Up and Down button to scroll to the accessory intend to pair and use.

2. To perform scanning these four 2.4GHz sensors of training equipments.

3. Once device is well paring, the display will show "OK" information.
4. Followed up, system will show HR/SP/CA/SC word regarding the well pairing equipment.

SENSORS HEART RATE HR SPEED NO CADENCE NO SPEED/CADENCE NO T 12:34AM ♥

11.4.2 Cardio Setting

[MAIN MENU] > [CONFIGURATION] > [ACCESSORIES] > [CARDIO SETTING]

You can select By AGE or CUSTOM to set up your heart rate zone or guiding Max heart is calculated by 220-age. The setting will be used for HR alarm.

You may input them according MAX HR or Percentage format.

HEART RT SETTING HR MAX BY AGE 192 ZONES USE CUSTOM BY AGE 1 96 b 2 115 bpm - 133 bpm 3 134 bpm - 153 bpm 4 154 bpm - 172 bpm 5 173 bpm - 192 bpm 02:01AM ♥

HEART RT SETTING HR MAX BY AGE 192 ZONES USE MAX VIEW bpm 1 9 CUSTOM H bpm 2 11 USE MAX B bpm 3 134 bpm - 153 bpm 4 154 bpm - 172 bpm 5 173 bpm - 192 bpm 02:02AM

11.4.3 Bike Setting

[MAIN MENU] > [CONFIGURATION] > [ACCESSORIES] > [BIKE SETTING]

You can set the bike weight and wheel size on this page. The setting will be used for cadence and speed sensor while be active. There are five wheels for setting.

BIKE SETTING BIKE BIKE 1 HEIGHT 11 kg WHEEL SIZE 1596 mm 02:02AM ♥

11.4.4 Baro Setting

[MAIN MENU] > [CONFIGURATION] > [ACCESSORIES] > [BARO SETTING]

Before getting training, it is recommended to calibrate the barometer in order to come out reliable value of altitude. There are two way to calibrate:

1. Auto Calibration: It is recommended to use. System will calibrate sensor upon GPS signal when the signal is reliable. It always calibrate one times after power on.
2. Manually calibration; you may go on government weather bureau to get your local Sea Level Pressure and then put in. System will accord to the value to come out the current altitude.

CALIBRATION AUTO S.L. PRESSU 019.30 mb ar CURRENT ALTITUDE 37 m 02:04AM ♥

11.4.5 Set Compass

[MAIN MENU] > [CONFIGURATION] > [ACCESSORIES] > [SET COMPASS]

- Calibration

Electronics compass can assist GPS and improve the unreliable problem from stationary. You have to calibrate before use that. You may follow instruction to calibrate.

Please Rotate 360° 02:05AM ♥

120 S E 210 60 240 30 W 300 N 330

- Declination

The practical magnet pole of Earth is ellipsoid, not ideal circus. You may manual input the declination value or set as auto calibration. It is recommended as AUTO.

DECLINATION OFF OFF MANUAL AUTO 02:06AM

- Follow Bearing

The bearing angle means the included angle between North and target point. You may perform as a real compass without GPS to reduce power consumption.

B N 02:08AM ♥

11.5 GPS Settings

[MAIN MENU] > [CONFIGURATION] > [USER SETTINGS] > [GPS SETTINGS]

- WAAS/EGNOS

You can turn on/off the "WAAS/EGNOS" feature.

GPS SETTING WAAS/EGNOS OFF GPS OFF GPS INFO ON

• GPS

The GPS function can be turned off for saving battery power. If the battery power is pretty low, the system will also ask you if you want to turn off the GPS function.

GPS SETTING WAAS/EGNOS OFF GPS ON GPS INFO OFF ON 02:10AM ♥

- GPS Info

Here you can see the positioning status of how many satellite signals are obtained and the signal strength.

MAP MODE SET BIRD EYE VIEW DIRECT TO NORTH BIRD EYE VIEW

MAP MODE SET BIRD EYE VIEW 200M IN/OUT AUTO AUTO MANUAL 02:20AM

11.6 Factory Reset

[MAIN MENU] > [CONFIGURATION] > [FACTORY RESET]

This feature allows you to restore the GB-580 back to factory default status. In another words, the training data, waypoint, and user profile will be erased.

CONFIGURATION RESTORE FACTORY SETTINGS? YES NO MAP MODE SET FACTORY RESET 02:21AM ♥

11.7 System Upgrade

[MAIN MENU] > [CONFIGURATION] > [SYSTEM UPGRADE]

1. Allow you to upgrade the firmware of GB-580.
2. If you want to cancel the upgrade process, press
   Power + ESC button at the same time.

CONFIGURATION DO YOU REALLY WANT TO UPDATE? YES NO FACTORY RESET SYSTEM UPGRAD 02:22AM ♥

11.8 About Product

[MAIN MENU] > [CONFIGURATION] > [ABOUT PRODUCT]

Display the firmware version information.

GS-Sport GB-580P Version: 1.01 F-GGH-2C-110304P SYSTEM OF GRAND ABOUT PRODUCT 02:22AM ♥

12. Troubleshooting

1.) Q: What should I do if the watch would not power on? A: Press the UP, OK, and Power buttons at the same time. You will be able to turn it on in the firmware upgrade mode. Please follow the regular firmware update procedure.
2.) Q: What should I do if the firmware upgrade fails?

Note: Do not power down your GB-580.

A: (1) Please go over the process again.

(2) Choose the proper firmware file.

3.) Q: After installing the software and opening it, a pop-up window shows up stating "The service is not ready." What should I do to resolve that?

A: Please close the program. Open it back again. The database will reset automatically.

4.) Q: How can I uninstall the GS-Sport Training Gym Pro software?

A: (1) Utilize the uninstall function from the Windows Menu:

Start > Programs > Globalsat GS-Sport Training Gym Pro > Uninstall

(2) Use Add or Remove Programs from Windows Control Panel:

Go to Start > Control Panel > Add or Remove Programs. Search for GS-Sport Training Gym Pro, click on it to highlight, and press the Change/Remove button.

5.) Q: Where can I download the files if I lost the CD-ROM?

A: Please go to this website:

http://www.gs-sport.com/pro_dl.php?en_product_id=10&en_product_cnt_id=33

6.) Q: How do I keep my current training records before upgrading the software version?

A: (1) Backup the database from this location: C:\Program Files\GlobalSat Technology\GS-Sport Training Gym Pro\Data\User. You can go ahead and uninstall the software.

(2) Copy and overwrite the database back to the corresponding folder.

7.) Q: Why am I unable to upgrade the watch with the new firmware?

A: (1) Please check if the firmware file is correct.

(2) Verify it the watch is set to System Upgrade mode.

8.) Q: Why does it show "PC COM PORT Error" when I tried to download the data from the device?

A: (1) Please check if the USB driver is installed or not.

(2) Connect the watch to your PC with the USB cable.

(3) Double click the GS-Sport Training GYM Pro' icon from the Desktop to start the application.

(4) In the Menu Bar, go to Settings > Configuration. Click the can COM Port" button. The COM Port would be automatically scanned.

9.) Q: Why is the device unable to receive a heart rate signal?

A: (1) Check if you are properly wearing the heart rate monitor. Also, spray some water on it before use.

(2) Turn on the Heart Rate Alert function.

(3) If it is still not working, check the battery of the Heart Rate Monitor.

10.) Q: How to edit and upload waypoints through the software?

A: To Edit Waypoints, see steps below:

(1) From Track Records, select the training file that you want to browse.
(2) Click Waypoints in the function bar and you will see all the waypoints. Right-click on one of the waypoints to edit its contents.
(3) Press the Save button when you're done.

To Upload Waypoints, refer to the procedures below:

(1) Select the waypoints that you want to transfer to the device.
(2) To upload, you can do this by going to Data Transmission > Way Points > Upload to Device.
(3) In the watch, please enter CONFIGURATION > CONNECT TO PC.
(4) Afterwards, it should show that you successfully uploaded the waypoint into the device.

11.) Q: What formats of the training file do the software supports?

A: It can save or open a training record as or from the following formats: .kml, .nmea, .gpx, csv, and .txt.

To open a file, go to File > Open. Choose a certain file you want to open.

To save a file, select one training file you want to save. Go to File > Save. Choose a certain file type you want to save it as.

12.) Q: How to import or export the training records from or to an activity file?

A: To import the training records from a specific file (.ACT):

Go to Main > Import Activity. Choose the file you want to import.

To export the training records to a specific file (.ACT):

Choose one training file you want to export. Go to Main > Export Activity > Activity Details. Input additional note. Click OK.

13.) Q: Why does it always show "Application database not ready" whenever I execute the software?

A: Please try the following:

(1) Navigate to the Services Setting by going to START > Control Panel > System & Maintenance > Administrative Tools > Services.

(2) Find out service name MySQL1.

(3) Select MySQL1 and click Start to connect it.

(4) Please try to open up the program again.

14.) Q: How do I check the firmware version of my watch?

A: You can do this by going to Main Menu > Configuration > About Product. The last line should indicate the firmware version of your watch, in this format: F-XXX-XX-XXXXXXX.

15.) Q: What languages are currently supported by my watch?

A: The languages currently supported by the watch are as follows: English, Spanish, Italian, France, German, Chinese, and Russian.

FCC Notices

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC RF Exposure requirements:

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.