CDP620GBXG-07 - Washing machine CANDY - Free user manual and instructions

USER MANUAL CDP620GBXG-07 CANDY

Technical line drawing of a mechanical assembly with mounting base and internal components (no text or symbols)

Рис. 2

Technical line drawing of a mechanical assembly with mounting base and internal components (no text or symbols)

Рис. 3-II

Technical line drawing of a mechanical assembly with mounting base and internal components (no text or symbols)

Замена лампы

Technical line drawing of a mechanical assembly with mounting base and internal components (no text or symbols)

Technical line drawing of a mechanical assembly with mounting brackets and circular components (no text or symbols)

Technical line drawing of a mechanical device with a handle and circular components (no text or symbols)

Technical line drawing of a mechanical device with mounting base and two hanging components (no text or symbols)

"Qingdao Xingbang Electronic Appliances Co., Ltd." No.417 Huaihe West Road, Huangdao District, Qingdao, 266510, Shandong, Kitai

Grid of grayscale rectangular blocks with varying shades of gray, no text or symbols present

УСТАНОВКА

Grid of grayscale rectangular blocks with varying shades of gray, no text or symbols present

3x Ø 8 x 40MM 2x Ø 4 x 35MM Рис. 7

10MM Рис.8

2 x 8 2x Ø 8x40MM 2x Ø 4x35MM Рис. 9

OK! Рис. 10

Grid of grayscale rectangular blocks with varying shades of gray, no text or symbols present

OK! 3x Ø 8x40 MM 3x Ø 4x35 MM Рис. 15

Technical line drawing of a mechanical device with a magnified inset showing internal components (no text or symbols)

Technical line drawing of a mechanical device with a cylindrical component and open lid, labeled 'Рис.. 17' (no text or symbols on the diagram itself)

Technical line drawing of a mechanical device with a cylindrical component and an arrow indicating motion (no text or symbols)

Ø 4x10 4x MM Рис.. 18

CANDY

MB60E-L16K BK

MB60E-L16K WH

MB60E-L11K-G1

Extractors

Manual for Installation, Use and Maintenance

Information and advice

CAUTION: Accessible parts may become hot when used with cooking appliances.

In certain circumstances electrical appliance may be a danger hazard.

A) There must be adequate ventilation of the room when the cooker hood is used at the same time as appliances burning gas or other fuels.

B) Do not check the status of the filters while the cooker hood is operating

C) Do not touch the light bulb within half an hour after appliance has been use.

D) Do not light a flame under the cooker hood.

E) Avoid opening gasometer when there is no pan on the stove, as it is damaging for the filters and a fire hazard.

F) Constantly check food frying to avoid overheated oil splashing and becoming a fire hazard.

G) Disconnect the electrical plug prior to any maintenance.

H) Regulations concerning the discharge of air have to be fulfilled.

I) When the range hood and appliances supplied with energy Other than electricity are simultaneously in operation. The negative pressure in the room must not exceed 4 Pa (4x10 ^-5 bar).

J) If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

K) This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised.

L) the range hood is inteded to be installed over a hob having no more than four hob elements.

M) Indoor use and household use only.

N) When the appliance is not in use and before cleaning, unplug the appliance from the outlet.

O) Attention! Observe the warning in the instruction sheet concerning the operation of the appliance when air is discharged from the room.

P) There is a fire risk if cleaning is not carried out in accordance with the instructions.

Using Your Extractor

For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking.

Remote receiver

Add key

Reduce key

illumination

power on/off

Power-on: When the power is turned on, the buzzer will sound a high pitch and enter the shutdown state.

Power off state: As long as the power button is off (the power indicator is off), it is defined as Power off state. Pressing the wind speed button at this time is invalid.

Power on state: In the Power off state, press the power button, the power indicator lights, and is defined as the power on state. Pressing all the keys at this time is valid

1) Power on/off button (delay button)

The power on state and the power off state are mutually converted. When the fan is running, press the power button to enter the delay state. The default delay is 15 minutes. The delay time is up and the power is turned off. When the wind speed switches to each other in the delay state, the delay automatically stops, press the power button to enter the shutdown state.

2) Add key Reduce key

After the power button is activated, press the add key button for 3 2 1 0 3 2 1... Press the reduce key for 1 2 3 0 1 2 3 0...

3) illumination

As long as the lighting button is pressed, the illumination indicator lights up and the illumination lamp works; when the button is pressed again, the illumination indicator is off and the illumination lamp stops working. Note that the illumination key is on or off and is not controlled by the power button.

Care and Maintenance

IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY.

Cleaning

You should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings.

You can clean your extractor effectively by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth.

Cleaning the Grease Filters

The grease filters should be kept clean to minimise the risk of fire.

At least once a month you should remove and clean the grease filters with hot soapy water. You can also wash the grease filters in a dishwasher, ensuring that you place them in an upright position to prevent damage from other items in the dishwasher. After rinsing and drying, replace the filters.

To remove the grease filters, push in the button on the handle and then pull down on the filters at the front. When you have released it at the front, then you can pull out the filter. To replace the grease filters, repeat the steps in reverse.

Please note:

Cleaning the grease filters in the dishwasher may lead to discolouration. This is normal and does not constitute a fault with the appliance.

Technical line drawing of a mechanical assembly with mounting base and internal components (no text or symbols)

Fig. 1

Diagram showing a solar panel being placed into a washing machine with water flowing out, illustrating the process of cleaning or cooling.

Fig. 2

Charcoal filter installation

IMPORTANT: DO NOT ATTEMPT TO MAINTAIN OR CLEAN THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY.

In re-circulating mode, air is vented back into the kitchen through the opening in the cooker hood.

This method is advised if you are not using your hob intensively. Re-circulated air requires the use of charcoal filters to remove odours.

To ensure the best performance from your cooker hood, the charcoal filter should be replaced every 3-6 months, dependent on use. Check with your local retailer or dealer for information on how to obtain replacement charcoal filters.

Note: This charcoal filter is non-washable and must be replaced as required.

To install a new charcoal filter, first remove the grease filter, as shown in Fig. 3-I. Then install a new charcoal filter as shown in Fig. 3-II and replace the grease filter (Fig. 3-III).

Technical line drawing of a mechanical assembly with mounting base and internal components (no text or symbols)

as 1 2 Fig. 3-II

Technical line drawing of a mechanical assembly with mounting base and internal components (no text or symbols)

Changing the Light

NOTE: Replacement of the LED lamp must be carried out by a qualified electrician.

IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY.

Please note that the LED lamp is not covered by the guarantee. Take out the grease filter.

Remove the lamp using a flat-head screwdriver.

Pull out the lamp and unplug the lamp wire connector. Replace the lamp and plug the wire connector into the new lamp.

Place the new lamp in the lamp holder. Push it into position until it clicks into place.

The light is designed for use during cooking and not for general room illumination. Extended use of the light can reduce the life span of the lamp.

2X1W LED MAX

Technical line drawing of a mechanical assembly with mounting base and internal components (no text or symbols)

Fig. 4-1

Technical line drawing of a mechanical assembly with two circular components and mounting brackets (no text or symbols)

Fig. 4-II

Technical line drawing of a mechanical assembly with no visible text or symbols

Fig. 4-III

Technical line drawing of a mechanical device with two hanging components and a central square component (no text or symbols)

Fig. 4-IV

Mains Electricity Connection

THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE.

Warning! This appliance must be earthed.

We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.T. and local regulations.

The wires in the mains lead of this appliance are coloured in accordance with the following code:

Green & Yellow = Earth, Blue = Neutral, Brown = Live.

As the colours of the wires in the mains lead for the appliance may not correspond with the coloured markings identifying the terminals connecting to the fuse spur, proceed as follows:

• The wire which is coloured green and yellow must be connected to the terminal marked E (Earth) or coloured green.
• The wire which is coloured blue must be connected to the terminal marked N (Neutral) or coloured black.
• The wire which is coloured brown must be connected to the terminal marked L (Live) or coloured red.

Note: Use a 3A Fuse

Assembly and electrical connection should be carried out by specialised personnel.

When installing this product we recommend you seek the help of another individual.

Do not mount the isolation switch behind the chimney section. It is a requirement that you must be able to isolate the extractor from the mains electrical supply after installation.

This appliance is intended to be connected to the mains electrical supply by means of an isolation switch and fused spur and is intended to be protected by a 3A fuse. The use of a 13A fuse can cause damage to the internal wiring in the event of a fault and will invalidate the warranty.

DOUBLE POLE SWITCHED FUSE SPUR OUTLET

FUSE ON

USE A 3 AMP FUSE

Electrical Information

Mains electrical voltage: 220-240V\~50Hz

Total rated power consumption:

162W

Troubleshooting

If your extractor is not working:

1. Check that the mains supply has not been switched off.
2. Check that the fuse in the spur has not blown.

INSTALLATION

MIN350mm MIN350mm 320 192 100 62 Ceramic-glass rings/hotplates 65 cm Gas cooker 75 cm Coal / oil / stove wood firing 85 cm

Fig. 5

3xø8

Fig. 6

IMPORTANT SAFETY WARNING: ONLY USE THE SCREWS PROVIDED WITH THE EXTRACTOR TO MOUNT THE DUCTING ADAPTOR. THE USE OF LONGER SCREWS MAY CAUSE DAMAGE TO THE INTERNAL WIRING WHICH WILL NOT BE COVERED BY THE WARRANTY.

3x Ø 8 x 40mm 2x Ø 4 x 35mm

Fig. 7

10mm

Fig. 8

Technical diagram showing mechanical assembly with dimension annotations and tool path

Fig. 9

OK! Fig. 10

Technical line drawing of a mechanical assembly with an inset showing a magnified view of a component (no text or symbols present)

Fig. 16

Technical line drawing of a mechanical device with a cylindrical component and a red arrow indicating direction (no text or symbols)

Technical line drawing of a mechanical device with a cylindrical component and an open base (no text or symbols)

Ø 4x10 mm 4x Fig. 18