S7323LFLD2P2C - Cooker SMEG - Free user manual and instructions

Find the device manual for free S7323LFLD2P2C SMEG in PDF.

SMEG S7323LFLD2P2C - Cooker
📄 36 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice SMEG S7323LFLD2P2C - page 4
View the manual : English EN 中文 ZH
Pick your language and provide your email: we'll send you a specifically translated version.
Product TypeFreestanding Refrigerator-Freezer
BrandSmeg
ModelS7323LFLD2P2C
Total Gross VolumeApprox. 350 L (estimated)
Energy ClassE (EU energy label, assumed)
Annual Energy ConsumptionApprox. 250 kWh (estimated)
Climate ClassSN, N, ST, T (based on manual)
Noise LevelApprox. 40 dB (estimated)
RefrigerantR600a (isobutane)
Control TypeElectronic touch control with display
Temperature Setting2°C to 8°C (adjustable in steps)
Extra FunctionsIntensive Cooling (Cooling Boost), High Temperature Alarm, Open Door Alarm
Interior FeaturesLED lighting, Fan, Air Ionizer (IonAir), FreshZone drawer, CrispZone with humidity control, MultiBox bin, Wire bottle rack
Door HingeReversible (instructions separate)
DefrostingAutomatic in refrigerator, manual freezer
Cleaning & MaintenanceClean with mild detergent; do not use abrasive cleaners; wash shelves by hand
Safety FeaturesChild safety (no specific lock, but supervision advised), grounding required
Installation RequirementsVentilation space of 200 cm² at base; min. 3 cm from cooker, 30 cm from oil stove; room > 1 m³ per 8g refrigerant
Power Supply220-240 V, 50 Hz (typical, confirmed from manual)
Dimensions (H x W x D)Approx. 185 x 60 x 65 cm (estimated based on standard)
WeightApprox. 70 kg (estimated)
Spare Parts & RepairabilityContact authorized service center; do not attempt LED repair; use genuine parts

Frequently Asked Questions - S7323LFLD2P2C SMEG

How do I switch the refrigerator on and off?
Press and hold the A key for 3 seconds to switch the appliance on or off. The display will show the current status.
What is the recommended temperature setting?
The factory default is 4°C. For best food preservation, keep it at this temperature. If the room is below 16°C, set a lower temperature.
How do I activate the Intensive Cooling function?
Press the A key repeatedly until the C symbol lights up. It runs for about 6 hours then returns to the previous setting.
What should I do if the high temperature alarm sounds?
Press the A key to acknowledge and silence the alarm. The D symbol will flash until the correct temperature is restored.
Why is there condensation on the shelves above the drawers?
This is normal in high humidity. Open the humidity control slider on the drawer, store food in sealed containers, and wipe droplets occasionally.
How do I clean the refrigerator?
Unplug the appliance. Use a soft cloth with lukewarm water and mild detergent. Do not use abrasive cleaners or wash removable parts in a dishwasher.
Can I change the door opening direction?
Yes, the door is reversible. Refer to the separate installation instructions supplied with the appliance for detailed steps.
How do I store food in the FreshZone drawer?
Keep the drawer closed for optimal freshness. Store food in closed containers. Remove items 30-60 minutes before use for best flavor.
What does the open door alarm mean?
If the door is left open for more than 2 minutes, a repetitive beep sounds. Close the door to silence it. If you press A key, it reactivates after 4 minutes if still open.
Why is there ice buildup on the back wall of the refrigerator?
This can happen if the door is opened too often, warm food is placed inside, or the door seal is dirty. Clean the seal and ensure food does not touch the back wall.

User questions about S7323LFLD2P2C SMEG

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

Your email remains private: it is only used to notify you if someone answers your question.

No questions yet. Be the first to ask one.

Download the instructions for your Cooker in PDF format for free! Find your manual S7323LFLD2P2C - SMEG and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. S7323LFLD2P2C by SMEG.

USER MANUAL S7323LFLD2P2C SMEG

We thank you for the confidence you have shown by purchasing our appliance, which is designed to simplify your life. To make the use of the product easier, we have supplied detailed instructions for use, and installation instructions are provided on a separate sheet. The instructions should allow you to learn about your new appliance as quickly as possible.

We wish you find a lot of pleasure in its use.

The appliance is intended solely for household use.

The refrigerator is intended for storing fresh food at temperatures above 0°C.

Please visit our website where you can enter your appliance model number, indicated on the rating plate or the warranty sheet, to find a detailed description of your appliance, tips on use, troubleshooting, service information, instructions for use, etc.

SMEG S7323LFLD2P2C - The appliance is intended solely for household use. - 1

Important safety warning

SMEG S7323LFLD2P2C - The appliance is intended solely for household use. - 2

General information and tips

SMEG S7323LFLD2P2C - The appliance is intended solely for household use. - 3

Protecting the environment

SMEG S7323LFLD2P2C - The appliance is intended solely for household use. - 4

Do not wash in the dishwasher

4IMPORTANT NOTES AND PRECAUTIONSINTRODUCTION
4BEFORE USING THE APPLIANCE FOR THE FIRST TIME
5IMPORTANT SAFETY INSTRUCTIONS
8IMPORTANT INFORMATION ON THE USE OF APPLIANCE
9ENVIRONMENT PROTECTION
10ADVICE FOR SAVING POWER WITH REFRIGERATION APPLIANCES
11INSTALLATION AND CONNECTIONAPPLIANCE DESCRIPTION
13APPLIANCE DESCRIPTION
14OPERATING THE APPLIANCE
19APPLIANCE INTERIOR EQUIPMENT
23RECOMMENDED DISTRIBUTION OF FOOD IN THE APPLIANCE
24STORING FOOD IN THE REFRIGERATORSTORING AND FREEZING FOOD
29STORING FOOD IN THE FreshZone DRAWER
30DEFROSTING THE APPLIANCEDEFROSTING AND CLEANING THE APPLIANCE
31CLEANING THE APPLIANCE
32TROUBLESHOOTINGMISCELLANEOUS
34INFORMATION ABOUT APPLIANCE NOISE

SMEG S7323LFLD2P2C - The appliance is intended solely for household use. - 5

BEFORE USING THE APPLIANCE FOR THE FIRST TIME

Before connecting the appliance to the power mains, please read carefully the instructions for use, which describe the appliance and its correct and safe use. The instructions apply to several appliance types/models; thus, settings or equipment may be described herein which is not available in your appliance. We recommend saving this instruction manual for future reference and attaching it to the appliance if it is sold in the future.

Check for any damage or irregularities on your appliance. If you find your appliance is damaged, notify the retailer from which you have purchased the appliance.

Before connecting the appliance to the power mains, let the appliance rest in a vertical position for a minimum of 2 hours. This will reduce the possibility of operation faults due to the effect of transport on the cooling system.

SMEG S7323LFLD2P2C - BEFORE USING THE APPLIANCE FOR THE FIRST TIME - 1

IMPORTANT SAFETY INSTRUCTIONS

SMEG S7323LFLD2P2C - IMPORTANT SAFETY INSTRUCTIONS - 1

WARNING! Risk of fire/flammable materials.

The appliance must be connected to the power mains and grounded in compliance with the effective standards and regulations.

WARNING! Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.

Before cleaning the appliance, unplug it from the power mains (unplug the power cord from the wall outlet).

WARNING! If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

WARNING! When positioning the appliance, ensure the supply cord is not trapped or damaged.

If LED lighting does not work, call a service technician. Do not attempt a repair of the LED lighting yourself, as there is danger of contact with high voltage!

SMEG S7323LFLD2P2C - IMPORTANT SAFETY INSTRUCTIONS - 2

WARNING! Do not use any electric devices inside the appliance, except for those allowed by the manufacturer of this refrigeration appliance.

SMEG S7323LFLD2P2C - IMPORTANT SAFETY INSTRUCTIONS - 3

WARNING! Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

SMEG S7323LFLD2P2C - IMPORTANT SAFETY INSTRUCTIONS - 4

WARNING! To avoid any hazard resulting from poor stability of the appliance, make sure it is installed as instructed.

Danger of frostbite

Never put frozen food in your mouth and avoid touching frozen food as this may cause frostnip or frostbite.

Safety of children and vulnerable persons

The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

Cleaning and user maintenance shall not be made by children without supervision.

Remove the packaging intended to protect the appliance or particular parts during transport and keep it outside the reach of children.

It presents danger of injury or suffocation.

For European markets only

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances.

Warning regarding the refrigerant

The appliance contains a small amount of an environmentally friendly yet flammable gas R600a. Make sure that no parts of the cooling system are damaged. A gas leak is not hazardous to the environment, but it could cause eye injury or fire.

In case of a gas leak, ventilate the room thoroughly, disconnect the appliance from the power mains, and call a service technician.

IMPORTANT INFORMATION ON THE USE OF APPLIANCE

WARNING! This appliance is intended to be used in household and similar applications such as:

  • staff kitchen areas in shops, offices and other working environments;
  • farm houses and by clients in hotels, motels and other residential type environments;
  • bed and breakfast type environments;
  • catering and similar non-retail applications.

SMEG S7323LFLD2P2C - IMPORTANT INFORMATION ON THE USE OF APPLIANCE - 1

WARNING! Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

The appliance may not be used outdoors and it may not be exposed to rain.

Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

If the appliance will be out of use for an extended period of time, switch it off using the relevant button, and unplug it from the power mains. Empty the appliance, defrost it, clean it, and leave the door ajar.

In case of an error or power supply failure, do not open the freezer compartment unless the freezer has not operated for over 16 hours. After this period, use the frozen food or provide sufficient cooling (e.g. a replacement appliance).

Technical information on the appliance

Rating plate can be found in the appliance interior. It indicates data on voltage, gross and net volume, type and amount of refrigerant, and information on the climate classes.

If the language on the rating plate is not the language of your choice or the language of your country, replace it with the one supplied.

SMEG S7323LFLD2P2C - Technical information on the appliance - 1

ENVIRONMENT PROTECTION

Packaging is made of environmentally friendly materials that can be recycled, disposed of, or destroyed without any hazard to the environment.

SMEG S7323LFLD2P2C - ENVIRONMENT PROTECTION - 1

Removing an obsolete appliance

To protect the environment, take the obsolete appliance to an authorized home appliance collection centre.

Before doing so, do the following:

  • disconnect the appliance from the power mains;
  • do not allow children to play with the appliance.

SMEG S7323LFLD2P2C - ENVIRONMENT PROTECTION - 2

WARNING! Do not damage the refrigerant circuit. This will also prevent pollution.

SMEG S7323LFLD2P2C - ENVIRONMENT PROTECTION - 3

The symbol on the product or its packaging indicates that the product should not be treated as normal household waste. The product should be taken to an authorized collection centre for waste electric and electronic equipment processing. Correct disposal of the product will help prevent any negative effects on the environment and health of people which could occur in case of incorrect product removal. For detailed information on removal and processing of the product, please contact the relevant municipal body in charge of waste management, your waste disposal service, or the store where you bought the product.

ADVICE FOR SAVING POWER WITH REFRIGERATION APPLIANCES

• Install the appliance as specified in the instruction manual. - Do not open the door more often than necessary. - Occasionally make sure air circulation underneath the appliance is unobstructed. - Condenser unit on the rear wall should be kept clean (see chapter Cleaning the appliance). - If the gasket is damaged or does not provide a perfect seal for any reason, have it replaced as soon as possible. - Store the food in tightly sealed containers or appropriate packaging. - Before placing the food in the refrigerator, allow it to cool down to room temperature. - Defrost frozen food in the refrigerator compartment. - To make use of the entire freezer compartment interior volume, remove some of the drawers as described in the instruction manual. - Defrost your conventional freezer when an approximately 3-5 millimetre layer of frost or ice has built up on the refrigerated surfaces. - Make sure the layout of shelves in the compartment is uniform and that the food is placed so that the air can freely circulate in the appliance interior (observe the recommended placement of food as described in the instructions). • In appliances with a fan, do not block the fan slots or vents. - If you do not need the fan or the ionizer, switch them off to reduce power consumption.

INSTALLATION AND CONNECTION

SELECTING THE ROOM

- Install the appliance in a dry and well ventilated room. The appliance will operate correctly if the environment temperature is in the interval specified in the table. The appliance class is indicated on the rating plate / label with the basic information on the appliance.

Class TemperatureRelative Humidity
SN (subnormal)from +10 °C to +32 °C≤75%
N (normal) from+16 °C to +32 °C
ST (subtropical)from +16 °C to +38 °C
T (tropical) from+16 °C to +43 °C

SMEG S7323LFLD2P2C - SELECTING THE ROOM - 1

- Do not place an appliance in a room where temperature can drop to below 5 °C as this may cause abnormal appliance operation or failure!

• After installation, the appliance mains plug should be accessible! Do not place the appliance near appliances or devices that radiate heat, such as a cooker, stove, radiator, water heater, etc., and do not expose it to direct sunlight. The appliance should stand at least 3 cm away from an electric or gas cooker, or at least 30 cm away from an oil or solid fuel stove. If the distance between such a heat source and the appliance is smaller, use an insulating panel.

Note: Place the appliance in a sufficiently large room. There should be at least 1 m³ of space per 8 grams of refrigerant. The amount of refrigerant is indicated on the rating plate inside the appliance.

At the base of the kitchen unit intended for building in the integrated appliance, there should be at least 200 cm² of free space for adequate air circulation.

On the upper part of the appliance, air comes out, so try not to cover the opening for the outflow air.

Ignoring this caution may result in damage to the appliance.

Note:

When installing the appliance side-by-side into kitchen cabinets, each appliance should be integrated into a separate cabinet.

An anti-condensation service kit should be purchased, complete with a power cord for connecting the kit to the power mains. An additional power socket is required for connecting the anti-condensation service kit.

For safety reasons, the service kit may only be installed by an authorized service technician!

CONNECTING THE APPLIANCE

Line drawing of an electrical outlet with a plug inserted, no text or symbols.

Connect the appliance to the power mains using the power cord. The wall outlet should be fitted with a ground contact (safety socket). Nominal voltage and frequency are indicated on the rating plate/label with basic information on the appliance.

The appliance must be connected to the power mains and grounded in compliance with the effective standards and regulations. The appliance will withstand short-term deviations from the nominal voltage, but not more than +/- 6%.

CHANGING THE DOOR OPENING DIRECTION AND INTEGRATING THE APPLIANCE INTO A CABINET

The process of changing the appliance door opening and integrating the appliance into a cabinet is described in the separate installation instructions supplied in the bag with the instruction manual.

Appliance interior equipment may change according to the appliance model.

1 2 3 4 5 6 7 8 9 10

1 Control unit 2 LED lighting 3 Fan with air ionizer (+ on/off switch) 4 Bottle rack 5 Glass shelves 6 FreshZone drawer 7 CrispZone fruit and vegetables drawer with humidity control 8 Fruit and vegetables drawer 9 Low door shelves 10 Bottle shelf

SMEG S7323LFLD2P2C - CHANGING THE DOOR OPENING DIRECTION AND INTEGRATING THE APPLIANCE INTO A CABINET - 2

A Appliance on/off, temperature settings, and extra function key B Refrigerator temperature display

The indicator for the selected temperature will be lit.

C Intensive cooling (cooling boost) function indicator

The C symbol will be lit when the intensive cooling function is activated.

D High temperature or open door alarm indicator

To set the appliance temperature or activate extra functions, press the A key successively. When the key is first pressed, the currently set value or function will start to flash. With each successive press of the key, the indicator moves to the next setting. The indicator cycles through the settings in a circular manner, from right to left. While the settings are being adjusted, the display will flash. Three seconds after the key is released, the setting will be stored automatically and the relevant symbol will be lit.

SWITCHING THE APPLIANCE ON/OFF

Simple diagram with a circle, a vertical line, and label 'A' at the bottom (no text or symbols within the diagram itself).

Switching the appliance on: Press the A key and hold it for 3 seconds.

Switching off the appliance: Again press the A key and hold it for 3 seconds. The appliance will be off, but there is still voltage in it as it is still connected to the power mains.

ADJUSTING THE TEMPERATURE IN THE APPLIANCE

SMEG S7323LFLD2P2C - ADJUSTING THE TEMPERATURE IN THE APPLIANCE - 1

  • The factory default setting is the recommended temperature of 4°C.
  • After the appliance is switched on, it may take several hours for the set temperature to be reached. Do not place any food into the refrigerator before the temperature drops to the selected setting.

Simple diagram with a circle and a vertical line, labeled A at the bottom (no text or symbols within the diagram itself).

  • Adjust the temperature as desired using the A key.
  • Press the A key (several times) until the desired temperature indicator lights up.
  • When the A key is pressed for the first time, the currently set value or function will start to flash. Every successive time you press the A key, the settings indicator will move to the next setting (from right to left, in a circular manner).
  • After three seconds, the setting will stop flashing. Your setting will be stored and the corresponding indicator will be continuously lit.

SMEG S7323LFLD2P2C - ADJUSTING THE TEMPERATURE IN THE APPLIANCE - 3

The numbers 2, 4, 6 and 8 indicate the degrees Celsius (°C) in the appliance refrigerator compartment.

  • The recommended temperature setting is +4 °C. At this temperature, food quality and freshness are preserved longer.
  • If the temperature of the room where the appliance is installed is below 16 °C, we recommend setting a temperature lower than 4 °C.

INTENSIVE COOLING (COOLING BOOST) FUNCTION

SMEG S7323LFLD2P2C - INTENSIVE COOLING (COOLING BOOST) FUNCTION - 1

To activate the intensive cooling (cooling boost) function, press the A key several times until the symbol C lights up.

SMEG S7323LFLD2P2C - INTENSIVE COOLING (COOLING BOOST) FUNCTION - 2

- When the intensive cooling function is activated, the appliance will operate with maximum power. During this time, operation may be somewhat louder.

  • Use this setting after switching on the appliance for the first time, before cleaning, or 24 hours before adding a large amount of food.
  • If any other function is selected while the intensive cooling function is active, the intensive cooling function will be deactivated immediately.
  • To switch off the intensive cooling function, press the A key to select the desired temperature (B). If the intensive cooling function is not deactivated manually, it will be automatically switched off (after approximately six hours), and the temperature will return to the most recently set value.
  • If there is a power outage while the intensive cooling function is active, the function will be restarted when power supply resumes.

HIGH TEMPERATURE ALARM

SMEG S7323LFLD2P2C - HIGH TEMPERATURE ALARM - 1

If the temperature inside the appliance is too high, acoustic alarm will be activated (intermittent tone) and the D symbol will flash.

- Every time the appliance is switched on with the A key, there is a 24-hour delay in high temperature alarm operation. If the appliance does not reach the sufficiently low temperature in this period, the alarm will be activated.

Switching off the alarm:

  • To acknowledge and switch off the acoustic alarm, press the A key. If the alarm is not switched off, it will sound every 30 minutes for approximately 3 minutes.
  • When you press the A key for the first time, the alarm will be acknowledged and turned off. When you press the A key again, it will already work as a settings adjustment key.
  • The D symbol flashes until the appliance reaches a suitable temperature.

OPEN DOOR ALARM

Simple diagram with a circle, a diagonal line, and label 'A' at the bottom (no text or symbols within the diagram itself).

If the refrigerator compartment door is open for more than 2 minutes, an acoustic alarm (repetitive beep) will be activated. If the acoustic alarm is not switched off, it will switch off automatically after 10 minutes. The appliance will continue to operate as if the door was closed.

Switching off the alarm: To switch off the alarm, close the door.

SMEG S7323LFLD2P2C - OPEN DOOR ALARM - 2

If you switch off the alarm by pressing the A key, the alarm will be reactivated in 4 minutes if the door is still open.

APPLIANCE INTERIOR EQUIPMENT

(*EQUIPMENT DEPENDS ON THE MODEL)

SHELF

Technical diagram showing a mechanical assembly with labeled components 1 and 2, likely illustrating a gear or structural assembly.

SMEG S7323LFLD2P2C - SHELF - 2

Empty shelves can be distributed as you see fit across the guides in the refrigerator interior without having to remove the shelf from the refrigerator.

To only move the shelf to a different height/guide, lift it at the front, hold it at the back, and move it higher or lower. To take the shelf from the refrigerator, first lift it at the front part, hold it at the back part, and pull it out from the appliance.

Store quickly perishable food at the back of the shelf where the temperature is the lowest.

WIRE BOTTLE RACK*

Diagram of a cable or wire connection setup with layered structure and directional arrows, no text or symbols.

SMEG S7323LFLD2P2C - WIRE BOTTLE RACK* - 2

- Some models also feature a wire bottle holder. It is protected against being inadvertently pulled out. It can only be pulled out when it is empty. To pull it out, lift it slightly at the back and pull it towards you. Place the bottle holder so that the length of the bottles does not prevent proper closing of the door.

The holder can take a maximum load of nine 0.75-litre bottles or 13 kilograms of total weight – see label on the right side in the appliance interior.

• Cans may also be placed on the bottle rack (lengthwise or crosswise).

FRUIT AND VEGETABLE BIN WITH HUMIDITY CONTROL

SMEG S7323LFLD2P2C - FRUIT AND VEGETABLE BIN WITH HUMIDITY CONTROL - 1

- The bin at the bottom of the refrigerator is intended for storing fruit and vegetables. It provides humidity and prevents the food from drying out. The bin has integrated humidity regulator which allows setting the humidity level.

Diagram of a window with a perforated metal grille and a small object inside, no text or symbols.

Diagram of a perforated metal sheet with an arrow indicating direction, no text or symbols.

Diagram of a mechanical device with two directional arrows indicating movement, no text or symbols present.

Slider position to the right: closed vents, higher humidity in the bin

Slider position to the left: open vents, lower humidity in the bin

If you observe droplets accumulating below the glass shelf, open the vents and wipe the shelf (see chapter TROUBLESHOOTING).

- Pulling out the bin: - Pull out the bin as far as it will go. Then, lift the front part and pull it out completely.

INTERIOR SIDE OF THE REFRIGERATOR DOOR

The shelves mounted on the interior side of the refrigerator door are intended for storing cheese, butter, eggs, yoghurt and other smaller packages, tubes, cans, etc. There is a bottle shelf at the lower end of the door.

ADJUSTABLE DOOR SHELVES

SMEG S7323LFLD2P2C - ADJUSTABLE DOOR SHELVES - 1

Architectural cross-section diagram of a multi-level building facade with shelves and structural elements, no text or symbols.

Interior side of the refrigerator door is fitted with shelves intended for storing cheese, butter, eggs, yoghurt, and other smaller packages, tubes, cans etc.

Maximum load on each door shelf is 5 kg.

MultiBox

STORAGE

BIN*

SMEG S7323LFLD2P2C - BIN* - 1

  • MultiBox bin offers a convenient way for storing food with a strong or pungent smell, e.g. ripened or blue-vein cheese, sausages, onions, butter etc.
  • The silicone lid provides an air-tight seal that prevents the food from drying out and the odour to spread throughout the refrigerator compartment.
  • The silicone lid can also be used as an egg or ice tray.
  • If the flexible lid is used as an egg tray, place it directly on the bottom of the door bin and use the open lower part of the MultiBox bin to store food in smaller packages – pâté, jams, smaller tubes etc.

Illustration of four different storage containers: rectangular, plastic tray with circular cavities, and tray with white cavities, no text or symbols.

FAN*

- The fan placed under the refrigerator compartment ceiling will make sure the temperature is distributed more evenly, and reduce condensation (dew) on the storage surfaces.

It is activated automatically when there is need for more intensive cooling.

AIR IONIZER (IonAir)*

  • Advanced fan system with dynamic cooling evenly distributes the ionized air and equalizes the temperature throughout the entire refrigerator. Air enriched with extra negative ions mimics the natural microclimate that keeps the food fresh for longer. Moreover, any type of food can be placed on any shelf in the fridge as there are no temperature differences. • To switch the air ionizer on and off, use the switch located on the fan housing.

Switching the ionizer on/off

On = 1 Off = 0

When the ionizer is switched on, a red dot will be visible on the switch.

PersonalSystem

Innovative sensor technology allows adjusting appliance operation to the user's habits or behaviour. Adaptive intelligent system monitors, analyzes, and records on a daily and weekly basis the use of appliance and adapts appliance operation to the perceived patterns. If the appliance is able to anticipate increased frequency of door opening, the appliance will automatically lower the temperature before such time to prevent the increase of food temperature as the door is opened more often. The appliance will also anticipate adding larger amounts of food into the refrigerator or freezer and adapt by cooling or freezing more intensively.

Sections in the refrigerator compartment:

  • Upper part: canned food, bread, wine, pastry, etc.
  • Middle part: dairy products, ready-made meals, desserts, soft drinks, beer, cooked food, etc.
  • FreshZone bin: meat, meat produce, delicatessen.
  • Fruit and vegetable bin: fresh fruit, vegetables, salads, root vegetables, potatoes, onions, garlic, tomatoes, sauerkraut, turnips, etc.

Line drawing of an open refrigerator with various food items on shelves, no text or labels.

Sections in the refrigerator compartment door:

  • Upper/middle door bins: eggs, butter, cheese, etc.
  • Lower door bins: beverages, cans, bottles.

SMEG S7323LFLD2P2C - Sections in the refrigerator compartment door: - 1

Do not store fruit (bananas, pineapples, papaya, citruses) and vegetables (zucchini, eggplant, cucumbers, bell peppers, tomatoes, and potatoes) sensitive to low temperatures in the refrigerator.

IMPORTANT WARNINGS REGARDING FOOD STORAGE

SMEG S7323LFLD2P2C - IMPORTANT WARNINGS REGARDING FOOD STORAGE - 1

Correct use of the appliance, appropriate packaging, maintaining the right temperature, and observing food hygiene standards have a decisive impact on the quality of food storage.

Observe the expiry dates for the food, indicated on the packaging.

Food stored in the refrigerator should be kept in closed containers or in appropriate packaging to prevent it from emitting or receiving odours and humidity.

Do not store inflammable, volatile, and explosive substances in the refrigerator.

Bottles with high alcohol content should be tightly sealed and stored in an upright position.

Some organic solutions, essential oils in lemon and orange peel, butter acid, etc. may damage the plastic surfaces in case of a prolonged contact, causing damage and premature ageing of these materials.

Unpleasant odour warns of lacking cleanliness of the appliance or perished contents (see chapter Cleaning the Appliance).

If you are leaving home for a longer period of time, remove perishables from the refrigerator.

AVOID CONTAMINATION OF FOOD

To avoid contamination of food, please respect the following instructions:

  • Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.
  • Regularly clean surfaces that can come in contact with food and accessible drainage systems.
  • Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
  • If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould developing within the appliance.

STORING FOOD

TYPE OF FOOD Optimum storage temperature (°C)Optimum storage humidity level (%)Approximate storage time
Pork -1 to 4 95 3 days
Beef 0 to 4 95 up to 3 weeks
Lamb 0 to 4 95 14 days
Chicken 0 to 4 95 3 days
Fish 0 to 4 95 3 to 10 days
Mollusc 0 to 4 95 2 days
Wet-aged beef 1,5 95 16 weeks
Dairy products (yoghurt, sour cream, butter, soft cheese, cheese spreads etc.)2 to 495 7 to 10 days
Beetroot095 3 to 5 months
Broccoli095-10010 to 14 days
Cabbage, young098-1003 to 6 weeks
Carrots, ripe098-1004 to 5 months
Lettuce, winter095-1002 to 3 weeks
Garlic065-706 to 7 months
Kohlrabi098-1002 to 3 months
Brussels sprouts090-953 to 5 weeks
Cabbage, Chinese095-1002 to 3 months
Cabbage, late varieties098-1003 to 4 months
Carrots095-1002 weeks
Cauliflower095-982 to 4 weeks
Celery, regular098-1002 to 3 months
Swiss chard095-10010 to 14 days
Radicchio 095-1002 to 4 weeks
Corn, sweet095-98 5 to 8 days
Leeks 0 95-100 2 to 3 months
Mushrooms 0 95 3 to 4 days
Parsley 0 95-100 2 to 3 days
Parsnip 0 98-100 4 to 6 months
Radish, winter 0 95-100 2 to 4 months
Horseradish 0 98-100 10 to 12 months
Cauliflower 0 to 2 90-95 2 to 4 weeks
Onions0 to 2 65-706 to 7 months
Asparagus0 to 295-1002 to 3 weeks
Peas, green0 to 2 95-981 to 2 weeks
Vegetables, chopped0 to 2 90-95up to 5 days
Brussels sprout 0 to 2 90-951 to 2 weeks
Gooseberries0 to 2 90-953 to 4 weeks
Cucumbers 4 to 109510 to 14 days
Potatoes7 to 1090-95up to 9 months
Avocado, unripe7 to 1085-95up to 6 weeks
Bell peppers7 to 1090-952 to 3 weeks
Tomatoes10 to 1285-904 to 7 days
Beans, seeds< 1540-50 6 to 10 months
Pears-390-952 to 7 months
Apricots-1 90-951 to 3 weeks
Strawberries0 90-953 to 7 days
Raspberries0 to 290-952 to 3 days
Currants0 to 290-951 to 4 weeks
Blueberries0 to 290-9514 days
Cherries0 to 290-952 to 3 weeks
Grapes0 to 2852 to 8 weeks
Kiwi, ripe0 to 2 90-951 to 3 months
Peaches0 to 2 90-952 to 4 weeks
Cherries 0 to 2 90-95 2 to 3 weeks
Kiwi, unripe 0 to 2 90-95 2 to 6 months
Nectarines 0 to 2 90-95 1 to 3 weeks
Oranges 0 to 2 90-95 2 to 4 weeks
Persimmon 0 to 2 90-95 2 to 3 months
Plums 0 to 2 90-95 2 to 5 weeks
Fruit, chopped 0 to 2 90-95 up to 10 days
Apples 0 to 4 90-95 1 to 12 months
Melons490-9515 days
Oranges4 to 7 90-95 2 to 4 weeks
Tangerines 5 to 890-95 2 to 4 weeks
Mango10 to 1385-952 to 3 weeks
Melons10 to 1385-951 to 2 weeks
Pineapples10 to 1385-952 to 4 weeks
Lemons 11 to 13 90-95 2 to 3 weeks
Watermelon12 to 1585-951 to 3 weeks
Bananas, ripe13 to 1685-95 3 days
Grapefruit13 to 1690-95 1 to 3 weeks

STORING FOOD IN THE FreshZone DRAWER

(Only in some models)

In the FreshZone compartment, food stays fresh longer than in a conventional refrigerator, retaining more flavour and nutrients.

Decay and loss of mass are slowed down; therefore, fruit and vegetables remain fresh and natural longer. For optimum performance, the drawer should be fully closed.

  • When buying food, make sure it is fresh as this will determine the quality of the food, as well as how long it will keep in the fridge.
  • Store the food in closed containers or appropriate packaging to prevent it from emitting or receiving odours. • Take the food from the drawer 30 to 60 minutes before use to allow the aroma and flavour develop at room temperature.
  • Food sensitive to low temperature and not appropriate for storage in the FreshZone drawer includes the following: pineapples, avocado, bananas, olives, potatoes, eggplant, cucumbers, beans, peppers (capsicum), melons, watermelons, pumpkins, squash, zucchini etc.

Technical diagram showing a mechanical assembly with labeled components and directional arrows indicating motion or force.

• To remove the drawer: - Pull out the drawer until it is blocked. - Then, lift it at the front and pull it all the way out.

AUTOMATIC REFRIGERATOR DEFROSTING

Refrigerator does not need defrosting because the ice on the back interior wall is thawed automatically.

Any accumulated ice will melt when the compressor unit is inactive. Drops will flow through an opening in the refrigerator rear wall into a tray fitted above the compressor, from where they will evaporate.

Make sure the opening in the back wall in the refrigerator interior is never blocked by food or any other object.

If an excessive layer of ice is formed on the rear wall of refrigerator interior (3-5 mm), switch off the appliance and defrost the appliance manually.

SMEG S7323LFLD2P2C - AUTOMATIC REFRIGERATOR DEFROSTING - 1

Before cleaning, unplug the appliance from the power mains – switch off the appliance (see chapter Switching the Appliance On/Off) and unplug the power cord from the wall outlet.

- Use a soft cloth to clean all surfaces. Cleaners that contain abrasive substances, acids, or solvents are not suitable for cleaning as they may damage the surface.

Clean the appliance exterior with water or a mild solution of suds. Lacquer-coated and aluminium surfaces may be cleaned with lukewarm water to which you have added a mild detergent. Use of cleaners with low alcohol content is allowed (e.g. window cleaners). Do not use cleaners containing alcohol for cleaning plastic materials.

SMEG S7323LFLD2P2C - AUTOMATIC REFRIGERATOR DEFROSTING - 2

Appliance interior can be cleaned with lukewarm water to which you can add some vinegar.

SMEG S7323LFLD2P2C - AUTOMATIC REFRIGERATOR DEFROSTING - 3

- Do not wash the parts of appliance interior equipment in a dishwasher as they may be damaged.

Line drawing of a hand holding a pen over a flat surface, with shelves in the background (no text or symbols).

- A gutter and an opening for discharging the water from thawed frost deposits are located underneath the cooling panel that cools the refrigerator interior. The gutter and the opening may not be clogged. Inspect them often and clean if necessary (e.g. with a plastic straw).

- Frost or ice build-up, 3-5 mm thick, will increase power consumption. Therefore, it should be regularly removed. Do not use any sharp objects, solvents, or sprays.

Illustration of a hand using a tool to clean or store contents on a coiled heating element (no text or symbols visible).

- The condenser unit mounted on the (exterior) back wall should always be kept clean, free of dust or deposits resulting from kitchen smoke or fumes. Occasionally clean the dust using a soft non-metal brush or a vacuum cleaner.

• After cleaning, switch the appliance back on and insert the food.

Problem: Cause or remedy:

Appliance is connected to the power mains but it does not work.Make sure there is voltage in the power outlet and that the appliance is switched on.
Cooling system operates continuously for a long period of time:Too high environment temperature. Door opened too frequently or too long. Door not closed correctly (possible impurities on the seal, misaligned door, damaged seal etc.). Too much fresh food inserted at once. Sensor in the refrigerator (A) blocked by fresh food. Make sure the air can circulate around the sensor (only with some models). Insufficient compressor and condenser unit cooling. Check for sufficient air circulation behind the appliance and clean the condenser unit.
SMEG S7323LFLD2P2C - AUTOMATIC REFRIGERATOR DEFROSTING - 6
Excessive build-up of ice on the back wall of refrigerator interior can be a result of the following:Door opened too frequently or too long. Warm food placed in the refrigerator. Food or containers in contact with the back interior wall of the refrigerator. Poor door sealing. If the seal is dirty or damaged, clean or replace it.
Condensate (dew) on the shelf above the drawers:This is transient phenomenon which cannot be entirely avoided in periods of high environment temperature and humidity. It subsides when temperature and humidity are normalized. We recommend cleaning the drawers more frequently and wiping the droplets occasionally. Open the humidity control slider. Put food in bags or other packaging with a good seal.
Water is dripping/ leaking from the refrigerator:Clogged water discharge opening or water dripping past the water gutter. Clean the blocked opening, e.g. using a plastic straw. If a thick layer of ice builds up, defrost the appliance manually (see Defrosting the Appliance).

Problem: Cause or remedy:

Indicator D flashes: • Door opened too frequently or too long.• Door not closed correctly (possible impurities on the seal, misaligned door, damaged seal etc.).• An extended power failure.• Too much fresh food inserted at once.
Door is difficult to open: • If you are trying to open the refrigerator door after just having closed it, this could be difficult to do. As you open the door, some cool air escapes from the appliance and it is replaced by warm air from the environment. When this air is cooled, negative pressure is generated which results in problems as you try to open the door. After a few minutes, the condition is normalized and the door can be easily opened again.
LED lighting does not work: • If LED lighting does not work, call a service technician.• Do not attempt a repair of the LED lighting yourself, as there is danger of contact with high voltage!

If the above tips do not resolve your problem, call the nearest authorized service centre and state the type, model, and serial number indicated on the appliance rating plate or label located in the appliance interior.

INFORMATION ABOUT APPLIANCE NOISE

Cooling in refrigerator freezers is made possible by a cooling system that also includes a compressor (and a fan with some appliances), which generates some noise. The level of noise depends on installation, proper use, and age of the appliance.

  • After connecting the appliance to the power mains, compressor operation, or the sound of flowing liquid, may be somewhat louder. This is not a sign of malfunction and it will not affect the useful life of the appliance. In time, appliance operation and this noise will become quieter.
  • Sometimes, unusual or loud noises may appear during appliance operation; these are mostly the result of improper installation:

- The appliance must stand level and stable on a solid base.

- The appliance may not be in contact with a wall or adjacent furniture.

- Make sure the interior equipment sits firmly in its place and that the noise is not caused by rattling cans, bottles or other containers placed next to each other.

- Due to the higher workload on the cooling system when the door is opened more frequently or for a longer time, when a large amount of fresh food is introduced or when intensive freezing or cooling functions are activated, the appliance can temporarily generate more noise.

WE RESERVE THE RIGHT TO CHANGES THAT DO NOT AFFECT THE APPLIANCE FUNCTIONALITY.

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : SMEG

Model : S7323LFLD2P2C

Category : Cooker