ADHC 2.0 - Camera BLAUPUNKT - Free user manual and instructions

Product Type	AHD Reverse/Front Camera
Model	ADHC 2.0
Image Sensor	CMOS
TV System	PAL
Effective Pixels	1280 (H) x 720 (V)
Image Resolution	750 TVL
Frame Rate	25 fps
Exposure & Gain Control	Yes
Electronic Shutter	1/60 ~ 1/100000 sec
Auto White Balance	Yes
Minimum Illumination	0.1 Lux / F
Horizontal Viewing Angle	145°
Vertical Viewing Angle	125°
Diagonal Viewing Angle	170°
Operating Voltage	DC 9-16V
Current Draw	160-180 mA
Operating Temperature	-20 ~ +70 °C
Storage Temperature	-30 ~ +75 °C
Protection Grade	IP68
Connector Type	RCA / 4-pin DIN
Lens Construction	4 glass elements
Application	Front or Reverse AHD camera
Parking Line Support	Yes (removable via wire cutting)
Display Mirroring	Selectable via wire cutting (front/reverse)
Safety Notes	Install without obstructing driver; avoid high-pressure water; consult authorized dealer

Frequently Asked Questions - ADHC 2.0 BLAUPUNKT

How do I install the Blaupunkt ADHC 2.0 camera?

Connect the camera's black wire to ground, red wire to the reverse light positive, and video output to a compatible AHD display monitor. Ensure the mounting location does not obstruct the driver's view. Refer to the installation flowchart in the manual for detailed wiring.

Can I use ADHC 2.0 as a front camera?

Yes. For front camera use, cut the designated wire to flip the viewing display and remove parking lines. See the instructions under 'FRONT/REAR VIEW DISPLAY & PARKING LINE' in the manual.

Why is my display not showing the camera image when reversing?

First, confirm your monitor supports AHD input. Then check the reverse light power connection and the camera's red wire. If still no image, restart the monitor. If the problem persists, inspect the power cables for damage.

What is the resolution of the ADHC 2.0 camera?

The camera has 1280x720 effective pixels and an image resolution of 750 TVL.

Is the camera water resistant?

Yes, it has an IP68 protection grade, meaning it is dust-tight and can withstand immersion in water up to 1.5 meters depth for 30 minutes.

What power supply does the camera need?

It operates on DC 9-16V (typically 12V) and draws 160-180 mA. The red wire should be connected to a 12V reverse light or power source.

Can I use this camera with any car radio?

No, it requires a monitor or car radio that supports AHD camera input. Check your device's specifications before installation.

How do I clean the camera lens?

Remove the protective film before first use. For cleaning, use a soft, dry cloth. Avoid automatic car washes or high-pressure water jets as they may damage the camera.

What should I do if the image is mirrored?

The camera can be set for front or rear view. For front view, cut the wire to flip the image horizontally. For rear view, leave the wire intact. See the 'FRONT CAMERA / REVERSE CAMERA' section in the manual.

Does the camera record video?

No, the ADHC 2.0 is a camera only for live viewing; it does not record video or have built-in storage.

USER MANUAL ADHC 2.0 BLAUPUNKT

Enjoy it.

Safety Notes

This vehicle security system has been manufactured according to established safety guidelines. However, dangers may still occur if the safety notes in this manual is not observed. This manual is intended to familiarize the user with the reverse camera important functions. Read this carefully, prior to using the reverse camera. Keep this manual in an easily accessible location. In addition, do observe the instructions of the devices used in conjunction with this reverse camera.

Attentions

• Assign a mounting location that will not obstruct driver in any circumstances. Or cause injuries to drives and passengers in case of emergency brake or accidents.
• Ensure all wires are connected properly, and that the unit is functioning well before fitting the unit into the mount.
• Any unauthorized installation, disassembly or modification may cause malfunction to the unit and void warranty of the unit.
• Always use only the parts that are included with the units only.
• Do not damage vehicle components when drilling holes for the mount.
• Vehicle may differ from the description provided here. Consult an authorized Blaupunkt dealer or vehicle's manufacturer if the information provided here does not fit your specific installation requirement.

• This unit is applicable for front and reverse AHD camera use. Consult an authorized Blaupunkt dealer during installation.

• Unit does not record video.

• Avoid automatic car wash or high-pressure water to prevent water and pressure from damaging the camera or causing it to fall off.
• Do not install this unit near heater outlet.

This manual may be updated from time to time without any notice.

Disclaimer

In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products.

USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada.

Features	AHDC-2.0	AHDC-3.0
CMOS Image Sensor	√	√
PAL TV System	√	√
Effective Pixels	1280 (H) x 720 (V)	1280 (H) x 720 (V)
750TVL Image Resolution	√	√
25 Frame Per Second	√	√
Exposure & Gain Control	√	√
1/60~1/100000sec Electronic Shutter	√	√
Auto White Balance	√	√
Illumination Min.	0.1 Lux/F	0.1 Lux/F
Horizontal View	145°H	160°H
Vertical View	125°V	140°V
Diagonal View	170°D	170°D
DC12V Voltage	√	√
Current	160mA-180mA	160mA-180mA
DC9-16V Operating Voltage Range	√	√
Operating Temperature	-20~+70 °C	-20~+70 °C
Storage Temperature	-30~+75°C	-30~+75°C
Protection Grade	IP68	IP68
RCA/4 PIN DIN	√	√
Lens	4 glasses	5 glasses

graph TD
    A["AHD Display Monitor/Car Radio (AHD Supported)"] --> B["Black Wire (Ground)"]
    B --> C["AHD Reverse Camera"]
    B --> D["Red Wire"]
    D --> E["Reverse Light"]
    E --> F["P"]
    E --> G["R"]
    E --> H["N"]
    E --> I["D"]
    E --> J["L"]
    E --> K["L2"]

Ground the wire through the exterior body of the vehicle and keep connection intact.

Attention

• Remove protective film from camera lens before use.
  • Take extra precautions when setting up the connection near petrol tank and wires.
• Connect Red Wire ⊕ with reverse light.

FRONT/ REAR VIEW DISPLAY & PARKING LINE

Applicable for AHDC-2.0

graph LR
    A["GND Rear Power"] --> B["AHD Display Monitor/Car Radio (AHD Supported)"]
    B --> C["AHD Camera"]
    C --> D["Video"]
    D --> E["White"]
    D --> F["Blue"]

Black and white photo of a white car driving on a road at dusk with cloudy sky and distant mountains (no visible text or symbols)

Black and white photo of a white SUV driving on a cloudy road under a cloudy sky, with a blue arrow pointing to the left side (no text or symbols visible)

Reverse Camera

Do not cut this wire when using as reverse camera.

Front Camera

Cut this wire when using as front camera to flip viewing display.

Black and white photo of a winding road with a visible crack, captured in an outdoor setting (no text or symbols)

Reverse Camera

Do not cut this wire when using as reverse camera.

Front Camera

Cut this wire when using as front camera to remove parking line.

Applicable for AHDC-3.0

AHD Display Monitor/ Car Radio (AHD Supported)

graph LR
    A["AHD Camera Video"] --> B["White"]
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333

Not applicable for AHDC 3.0 with serial number:

200202AHDC3000001 to 200202AHDC3000500

White SUV driving on a desert road under cloudy sky, with a blue arrow pointing to the left (no text or symbols visible)

For Reverse Camera

Front Camera

Reconnect this wire when using as front camera to flip viewing display and remove parking line.

Remarks :
1. Pictures are for illustration purpose only, see actual vehicle for accurate installation location.
2. Ensure diameter of hole size is correct before drilling.
3. Ensure drilling process does not harm the component of the vehicle.
4. Assign mounting location that will not obstruct camera view.

If any of the following problem occur, please resort to Troubleshooting for the possible solutions. Consult Blaupunkt authorized dealer if problem persist.

Problem	Solution
Display monitor / car radio does not show reverse view when reversing.	Examine the car player to confirm whether AHD camera input is supported or not.
	Restart the display monitor / car radio.
Reverse view does not show even after restarting the display monitor/ car radio.	Examine if the power supplies of the reverse light or the rear car plate light is properly connected.
Reverse view does not show even though power supplies of the reverse light or the rear car plate light is properly connected.	Examine if the power supply cables of the reverse light or the rear car plate light is damaged. Repair/replace if the cables are damaged.

Designed and engineered by Blaupunkt Competence Centre

AHDC-2.0

1 331 20 008 32 01

AHDC-3.0

1 331 20 009 32 01