GRM1018 - Pressure washer Ferm - Free user manual and instructions

Brand	Ferm
Model	GRM1018
Product Type	High Pressure Cleaner (Pressure Washer)
Voltage	230 V~ / 50 Hz
Input Power	1800 W
Max. Water Supply Pressure	4 bar (0.4 MPa)
Max. Working Pressure	165 bar
Max. Water Temperature	50°C
Max. Flow Rate	7.2 L/min
Hose Length	6 m
Weight	20 kg
IP Rating	IPX5
Sound Pressure Level	78 dB(A)
Sound Power Level	96 dB(A)
Vibration Level	<2.5 m/s²
Water Connection	Not for potable water; use backflow preventer if connecting to mains
Safety Features	Thermal cutout, trigger lock, grounded plug
Detergent System	Integrated detergent bottle with low-pressure application
Adjustable Nozzle	Yes, linear and fan spray, high/low pressure adjustment
Contents	High pressure cleaner, hose, trigger gun, lance holder, lance extension, adjustable nozzle, detergent bottle, manual, warranty card

Frequently Asked Questions - GRM1018 Ferm

How do I start the pressure washer?

Ensure water supply is connected and turned on. Depress the trigger to expel air, then lock the trigger. Plug in the machine and turn the power switch on. Unlock the trigger to start spraying.

What type of water can I use?

Use only clean cold water. Do not use corrosive chemicals or unfiltered water, as they can damage the pump. Maximum water temperature is 50°C.

How do I adjust the pressure?

Make sure the trigger is released. To increase pressure, turn the rear part of the spray nozzle counterclockwise. To decrease pressure, turn it clockwise. The nozzle also adjusts spray pattern from linear to fan.

How do I use detergent?

Fill the detergent bottle. Set the adjustable spray wand to low pressure position. Squeeze the trigger to spray detergent. For best results, apply from bottom to top on vertical surfaces.

What should I do if the motor stops suddenly?

This may be due to the thermal cutout tripping from overheating. Wait 2-3 minutes for the motor to cool. Check that the extension cord is heavy enough and fully unrolled. If the problem persists, consult a qualified technician.

How do I store the pressure washer in winter?

Protect the unit from freezing. Operate the cleaner with non-corrosive antifreeze before storage. Store in a dry, well-ventilated place with temperature above +5°C.

Can I connect the pressure washer to a potable water supply?

The machine is not intended to be connected directly to the potable water mains. If you must connect to a potable water supply, install a backflow preventer (EN 60335-2-79 ANNEX AA).

How do I clean the water inlet filter?

The water inlet filter should be inspected regularly. To clean, remove the filter and rinse it with clean water. Ensure it is free of debris before reinstalling. Perform this every 50 hours of operation.

What safety precautions are essential?

Never direct the jet at people, animals, live electrical equipment, or the machine itself. Wear ear protection. Keep children away. Use a RCD (residual current device) with leakage current <30 mA. Always lock the trigger when not in use.

How can I achieve the best cleaning results?

For stubborn dirt, use detergent at low pressure. Let it sit for a few minutes. Rinse with high pressure from bottom to top to avoid streaks. Keep the nozzle at least 30 cm from painted surfaces to prevent damage.

USER MANUAL GRM1018 Ferm

Exterior view of a FERM water heater with blue and gray casing (no visible text or symbols)

GRM1018

EN

Original instructions 04

Illustration of two hand gestures with arrows indicating motion (no text or symbols)

Diagram of a mechanical component with an arrow indicating rotation or force direction (no text or symbols)

Diagram of a cable or connector being twisted with an arrow indicating rotation (no text or symbols present)

Fig. 3

Fig. 4

Close-up of a mechanical component with a central knob and multiple side grooves (no visible text or symbols)

Close-up of a metallic surface with a circular hole and evenly spaced rectangular slots (no text or symbols visible)

Fig. 5

HIGH PRESSURE CLEANER

The numbers in the text refer to the diagrams on pages 2-3.

For your own safety and that of others, we recommend that you read this instruction manual carefully before using this machine. Keep this instruction manual and the documentation provided with the machine for future reference.

Introduction

The high pressure cleaner GRM1018 is quick and efficient for cleaning vehicles, machines, boats, buildings, etc., by the removal of stubborn dirt using clean water and chemical detergents. When using chemical detergents, only use biodegradable types. Only clean vehicle engines in areas in which suitable oil traps are installed.

Contents

1. Machine information
2. Safety instructions
3. Assembly
4. Use
5. Service & maintenance

1. MACHINE INFORMATION

Technical specifications

Voltage 230 V\~ /50Hz

Input power 1800 W

Max. pressure water supply 4 bar

Allowable pressure 165 bar

Max. water temperature 50°C

Max. working flow rate 7.2 l/min

Hose length 6 m

Weight 20 kg

IP class IPX5

LPA(sound pressure) 78 dB(A), K=3 dB(A)

LWA(acoustic power) 96 dB(A)

Vibration value

<2.5m/s2

Contents of packing

1 High pressure cleaner
1 Hose
1 Trigger
1 Lance holder

1 Hose handle + screws
1 Lance extension
1 Lance adjustable nozzle
1 Detergent bottle (built in)
1 Safety and operating instructions
1 Warranty card

Check the appliance, any loose parts and accessories for damage caused during transport.

Product information

Fig. 1

1. High pressure washer
2. On/off switch
3. Water inlet
4. Wheel
5. Water outlet
6. Gun holder
7. Handle
8. Hose reel
9. Spray gun
10. Adjustable Spray Wand

2. SAFETY INSTRUCTIONS

Explanation of the symbols

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Indicates electrical shock hazard.

DO NOT direct the water jet towards people or animals. DO NOT direct the water jet towards the unit itself, electrical parts or towards other electrical

The machine is not intended to be connected to the potable water mains.

Safety instructions

When using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and

also the enclosed safety instructions.

Electrical safety

• Always check if your mains voltage corresponds with the value on the type plate.
• When replacing old cables or plugs:
• Throw away old cables or plugs immediately as soon as new ones have replaced these. It is dangerous to put the plug of a loose cable into the socket outlet.
• When using extension cables:
• Only use an approved extension cable that is suitable for the machine's power. The cores must have a diameter of at least 1.5 mm^2 . When the extension cable is on a reel, unroll the cable in its entirety.
• All electrical connections e.g. extension cable, must be of an approved waterproof type for outdoor use and marked accordingly. Extension cables must be threecore, one of which is EARTH.

Immediately switch off the machine when:

• Interruption of the mains plug, mains lead or mains lead damage.
• Defectswitch
• Smoke or stench of scorched isolation

Specific safety rules

The USE and MAINTENANCE manual constitutes an essential part of the cleaner equipment and should be kept in a safe place for future reference. If you sell the cleaner, the manual should be handed on to the new owner.

• Before starting the cleaner, make sure that it is receiving water correctly. Operating the cleaner without water could damage the seals.
• Do not disconnect the plug by pulling on the electrical cable.
• If you are too far from the object you wish to clean, do not move the cleaner nearer by pulling on the high pressure hose; use the handle provided.
• In versions not equipped with TSS device, do not operate the cleaner for more than 1-2 minutes with the gun closed as this could damage the seals.
• Protect the cleaner from freezing during the winter.
• Do not obstruct the ventilation grilles during

operation.

• The cross-section of any extension cables used must be proportional to their length, i.e. the longer the extension cable, the greater the cross-section; cables with a protection level of "IPX5" must be used.
• Position the cleaner AS NEAR POSSIBLE to the water supply.
• The packaging is easily recyclable, and must be disposed of in compliance with the regulations in force in the country of installation.
• Use the cleaner only with accessories and replacement parts authorized by the manufacturer. The use of original accessories and replacement parts will ensure safe, trouble-free operation.
• The cleaner must be used standing on a secure, stable surface.
• Avoid unintentional firing of the trigger. Do not carry the lance/ trigger assembly with your hand over the trigger. Always use the trigger lock mechanism.
• Ensure that the safety lock on the trigger is used, when you have stopped using the pressure washer to prevent accidental operation. (fig 5)
• Read all the instructions before using the machine.
• Machines shall not be used by children. Children should be supervised to ensure that they do not play with the machine. This machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge
• The electrical supply connection shall be made by a qualified person and comply with IEC 60364-1. The electric supply to this machine should include either a residual current device that will interrupt the supply if the leakage current to earth exceeds 30 mA for 30 ms or a device that will prove the earth circuit.
• The machine is intended to be used at a temperature above o degree. (Only for machine with power cord of H05VV-F).
• The operating method to be followed in the event of accident (e.g. contact with detergents: rinse with an abundance of clean water) or breakdown to prevent unsafe situations.
  • This machine has been designed for use with

the cleaning agent supplied or recommended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the machine.

• Recommend the operator to wear ear protectors.
• Do not use the machine within range of persons unless they wear protective clothing.
• Do not direct the jet against yourself or others in order to clean clothes or foot-wear.

- Risk of explosion-Do not spray flammable liquids.

- High pressure hoses, fittings and couplings are important for the safety of the machine. Use only hosed, fittings and couplings recommended by the manufacturer.

- To ensure machine safety, use only original spare parts from the manufacturer or approved by the manufacturer.

- Water that has flown through backflow preventers is considered to the non-potable.

- The machine shall be disconnected from its power source by removing the plug from the socket-outlet during cleaning or maintenance and when replacing the machine to another function.

- Observe a distance of at least 30cm when using the jet to clean painted surfaces to avoid damaging paintwork.

- Do not use the machine if a supply cord or important parts of the machine are damaged, e.g. safety devices, high pressure hoses, trigger gun.

- If an extension cord is used, the plug and socket must be of watertight construction.

- Inadequate extension cords can be dangerous. If an extension cord is used, it shall be suitable for outdoor use, and the connection has to be kept dry and off the ground. It is recommended that this is accomplished by means of a cord reel which keeps the socket at least 60mm above the ground.

- In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

- To ensure the machine safety, please only use original spare parts (including nozzle) from the manufacturer or approved by the

manufacturer. Do not use the machine before you changed them if they are damaged.

- Be care of the danger of the kickback force on the spray assembly when opening the trigger gun and grasp the gun with hands firmly.

- To reduce the risk of injury, close supervision is necessary when a machine is used near children. High-pressure cleaner shall not be used by children or untrained person.

- Know how to stop the machine and bleed pressures quickly. Be thoroughly familiar with the controls.

- Stay alert and watch what you are doing.

- Do not operate the machine when fatigued or under the influence of alcohol or drugs.

- Keep operating area clear of all persons.

- Do not overreach or stand on unstable support. Keep good footing and balance at all times.

- Follow the maintenance instructions specified in the manual.

- This machine must be grounded. If it has malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. The rating voltage (V/Hz) of the machine has to be in compliance with the local power supplying voltage.

- Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the machine. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use any type of adapter with this machine.

- Use only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole cord connectors that accept the plug from the machine. Use only extension cords that are intended for outdoor use and the socket must be of watertight construction. These extension cords are identified by a marking "Acceptable for use with outdoor machines; store indoors while not in use." Use only extension cords having an electrical rating not less than the rating of the machine. Do not use damaged extension cords. Examine extension cord before using and replace if

damaged. Inadequate extension cords can be dangerous. Do not abuse extension cord and do not yank on any cord to disconnect. Keep cord away from heat and sharp edges. Always disconnect the extension cord from the receptacle before disconnecting the machine from the extension cord.

• To reduce the risk of electrocution, don't start and run the machine in the rain or storm. Keep all connections dry and off the ground. Do not touch plug with wet hands. It is strictly prohibited to let water leak into the machine.
• When the machine is turned on, the interior pumps start and continue to run even if the pressure wand trigger has not been depressed. Running the machine for more than 3 minutes without depressing the pressure wand trigger could cause heat damage to the motor and pumps, Please do not leave the machine running unattended or unused for more than 3 minutes.
• When the machine is running, please maintain a constant water supply. Without water circulation will damage the sealing rings of the machine.
• It is necessary to turn on the spray lance within one or two minutes after the machine has been started. Otherwise, the temperature of the circulating water within the machine will soon rise to a critical point, which will cause damage to the sealing rings inside the machine.
• Don't start and run the machine in a place excessively cold so as to prevent the machine from the freezing current.
• This machine has been designed for only using cleaning water, do not use corrosive chemicals.
• Use cleaning agent supplied or recommend by the manufacturer.
• High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, animals, live electrical equipment or the machine itself. Pressure washers should not be pointed at tire walls, as it may be possible to damage them.
• Do not direct the jet against yourself or others in order to clean clothes or footwear.
• Disconnect from the electrical power supply before carrying out user maintenance.
• If the mains cable is damaged it must be replaced by the manufacturer, or its service

agent or similarly qualified person to avoid a hazard.

• Do not use the machine if a supply cord or important parts are damaged, e.g. safety devices, high pressure hoses, trigger gun.
• Be aware of the recoil caused by the water jet when the machine is switched on.
• When the machine is moving and installing, the machine must be in flat. When moving the machine, pulling the handle to move it.
• Connect to the water supply. The machines are not suitable for connection to portable water mains. Connect the machine to the water supply. (It can be a water container).
• Make sure the inlet water pressure keeps between 0.01MPa and 0.4MPa. The inlet pipe should at least 5 M long. Do not use the pipe if the pipe is damaged. If you want connect this machine to portable water mains, you must install a backflow preventer in the water pipe to prevent dirty water flow back to the drinking water system. The backflow preventer shall comply with EN 60335-2-79 ANNEX AA.

3. ASSEMBLY AND USE

The motor of this pressure washer will NOT run. It will only operate when the trigger is squeezed.

• Connect the outlet hose to the washer and connect the spray gun to the outlet hose.
• Connect nozzle and nozzle extension.
• Check gauze filter is clear of any blockage.
• Connect the water supply hose.
• Check that the hose has no kinks in it.
• Turn on water and check for leaks.
• Depress trigger to allow air to be expelled though the pump and hoses, lock trigger.
• Plug in machine and turn on switch.
• Unlock trigger and use the pressure washer.

Shut down

1. Turn off the motor(push switch to the off position).
2. Unplug the unit from the power source.
3. Turn off the water supply.
4. Press the trigger of the gun to depressurize the system.
5. Disconnect the garden hose from the pressure

washer.

1. Wipe all surfaces of the unit with a damp clean cloth.
2. Engage the gun safety lock.

CAUTION: ALWAYS turn off the unit's motor BEFORE turning off the unit's water supply. Serious damage could occur to the motor if the unit is run without water.

CAUTION: NEVER disconnect the high-pressure discharge hose from the machine while the system is still pressurized. To depressurize the unit, turn off the motor, turn off the water supply and squeeze the trigger 2-3 times

Water supply

• Ensure that you have a suitable water supply to feed the pressure washer. Check that all connections are tight and there are no leaks in the hose.
• The supply tap should be fully open (do not turn on the pressure washer yet).
• Now depress the trigger (unlock trigger lock first) to let water pass through the unit and expel any air.

Warning! This unit is to be used with a cold-water source only!

- Turn on the pressure washer, once all the air has been expelled and water has reached the end of the lance.

Electrical Cables

- Ensure that all cables are damage free before connecting to the power supply.

Plug in the pressure washer and turn the unit on with the main switch (2).

4. USE

CAUTION! The cleaner must only be used with clean water; use of unfiltered water or corrosive chemicals will damage the cleaner.

• Turn the motor switch to the "0" position.
• Check that the electrical supply voltage and frequency (Volts/Hz) correspond to those specified on the cleaner data plate.
• If the power supply is correct, you may now plug in the cleaner.
• The electric supply connection shall be made by a qualified electrician. It is recommended that the electric supply to this appliance should include either a residual current device that will interrupt the supply if the leakage current to earth exceeds 30 mA for 30 ms or a device which will prove the earth circuit.

CAUTION! The machine may cause electrical disturbances when starting.

- If the motor stops and fails to restart, wait 2-3 minutes before restarting. THERMAL CUTOUT TRIPPED

Adjusting the nozzle

Fig. 2

- Water may be sprayed out of the nozzle either linearly or in a fan shape. Turn on the pressure first, and then adjust the nozzle.

Adjusting pressure

Fig. 3

Using High Pressure:

- Please make sure the trigger released and there is not any water spraying. then turn the rear part of spray nozzle counterclockwise. Squeeze the trigger, the gun will spray water with high pressure.

Using Low Pressure:

- Please make sure the trigger released and there is not any water spraying. then turn the rear part of spray nozzle clockwise. Squeeze the trigger, the gun will spray water with low pressure.

CAUTION: Selection of high or low pressure by turning action. The selection of the pressure must be carried out with the gun in closed position.

Water inlet filter

Fig. 4

- The water inlet filter must be inspected regularly, so as to avoid blockage and restriction of the water supply to the pump. (fig 4)

Using the detergent bottle

Fig. 5

• Add detergent to the container.
• Set the Adjustable Spray Wand at low pressure position.
• Trigger gun to spray detergent.

The use of detergents can dramatically reduce cleaning time and assist in the removal of difficult stains. Some detergents have been customized for pressure washer use on specific cleaning tasks. These detergents are approximately as thick as water. The use of thicker detergents, such as dish soap, will clog the chemical injection system and prevent the application of the detergent. The cleaning power of detergents comes from applying them to a surface and giving the chemicals time to break down the dirt and grime. Detergents work best when applied at low pressure. The combination of chemical action and high pressure rinsing is very effective. On vertical surfaces, apply the detergent starting at the bottom and work your way upward. This will prevent the detergent from sliding down and causing streaks. High pressure rinsing should also progress from the bottom to top. On particularly tough stains, it may be necessary to use a brush in combination with detergents and high pressure rinsing.

CAUTION! Never disconnect the high-pressure hose from the machine while the system is still pressurized.

Follow the correct procedure:

1. Turn off the pressure washer by using the switch on the machine.
2. Unplug the unit from the power source.
3. Turn off the water supply at the tap.
4. Press the trigger of the gun to depressurize the system.
5. Disconnect the supply hose to the machine
6. Wipe all surfaces of the unit with a damp clean cloth.
7. Engage the safety lock.

5. SERVICE & MAINTENANCE

Warning! Unplug the electric cable (power source) prior to any maintenance or preparatory storage operations.

• Make sure that the machine is not live when carrying out maintenance work on the motor.
• To ensure good performance, check and clean the suction and detergent filters after every 50 hours of operation.

Malfunction

Should the machine fail to function correctly, a number of possible causes and the appropriate solutions are given below:

1. When switched on, the machine will not start working.

• Plug is not well connected or electric socket is faulty.
• Check plug, socket and fuse.
• The mains voltage is lower than the minimum requirement for start up.
• Check that the mains voltage is adequate.
• The pump is stuck.
• Refer to after storage instructions. Switch off the unit and let the motor cool.
  • Thermal safety has tripped.
• Leave the lance open with water coming through.

2. Fluctuating pressure

• Pump sucking air
• Check that hoses and connections are airtight
• Valves dirty, worn out or stuck. Pump seals worn.
• Clean and replace or refer to dealer.

3. Water leaking from the pump

• Seals worn out
• Check and replace, or refer to dealer

4. The motor stops suddenly

• Thermal safety switch has tripped due to overheating.
• Check that the mains voltage corresponds to specifications. An extension cable, which is too thin, and tool long can cause a voltage drop and cause the motor to

overheat. Leave to cool down. Use heavy duty extension cables.

5. The pump does not reach the necessary pressure.

• Water inlet, filter is clogged
- Clean the water inlet filter
- Pump sucking air from connections or hoses
- Check that all supply connections are tight
- Suction/ delivery valves are clogged or worn out.
- Check that the water feeding hose is not leaking.
- Unloader valve is stuck
• Clear or respire valves
- Lance nozzle incorrect or worn out
- Loosen and re-tighten regulation screw Check and/or replace.

Repairs and servicing should only be carried out by a qualified technician or service firm.

Cleaning

Keep the ventilation slots of the machine clean to prevent overheating of the engine.

Clean the housing regularly with a soft cloth, preferably every time it is used.

Keep the air vents free f dust and dirt. Remove stubborn dirt with a soft rag moistened in soapy water. Do not use any solvents such as petrol, alcohol, ammonia, etc. as such substances can damage the plastic parts.

Lubrication

The appliance does not need any extra lubrication.

Storage and transportation

Keep the high pressure washer in well-ventilated dry premises with temperature not going below +5°C. Operate the cleaner with non-corrosive/non-toxic antifreeze before storing for the winter.

Faults

If a fault arises through wear in an element, please contact the service address shown on the warranty card. A drawing of the spare parts that may be obtained is included at the end of these operating instructions.

ENVIRONMENT

To prevent damage during transport, the appliance is delivered in a solid packaging which consists largely of reusable material. Therefore please make use of options for recycling the packaging.

Damaged and/or disposed of electrical or electronic devices must be dropped off at recycling stations intended for that purpose.

WARRANTY

Read the terms of warranty on the separate warranty card which is enclosed.

Spare parts list

GRM1018

No. Description Position
501094 Filter B 18
502096 Valve set B 34 - 37
800795 Capacitor B 47
501097 Main switch B 50
501230 Hose A 45
502095 Wheel A 22 - 25
503011 Detergent spray	attachment A 17 & 19
502099 Trigger A 42
521220 Lance rear A 43
521233 Lance front A 44

Exploded view B

CE

DECLARATION OF CONFORMITY GRM1018 - HIGH PRESSURE CLEANER

(EN) We declare under our sole responsibility that this product is in conformity with directive 2011/65/EU of the European parliament and of the council of 9 June on the restriction of the use of certain hazardous substances in electrical and electronic equipment is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt der Direktive 2011/65/EU des Europäischen Parlaments und des Rats vom 8. Juni 2011 über die Einschränkung der Anwendung von bestimmten gefährlichen Stoffen in elektrischen und elektronischen Geräten entspricht, den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijkheid dat dit product voldoet aan de conform Richtlijn 2011/65/EU van het Europees Parlement en de Raad van 8 juni 2011 betreffende beperking van het gebruik van bepaalde gevaarlijke stoffen in elektrische en elektronische apparatuur en in overeenstem ming is met de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants: est conforme à la Directive 2011/65/EU du Parlement Européen et du Conseil du 8 juin 2011 concernant la limitation d'usage de certaines substances dangereuses dans l'équipement électrique et électronique.
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento: se encuentra conforme con la Directiva 2011/65/UE del Parlamento Europeo y del Consejo de 8 de junio de 2011 sobre la restricción del uso de determinadas sustancias peligrosas en los equipos eléctricos y electrónicos.
(PT) Declaramos por nossa total responsabilidade-de que este produto está em conformidade e cumpre as normas e regulamentações que se seguem: está em conformidade com a Directiva 2011/65/EU do Parlamento Europeu e com o Conselho de 8 de Junho de 2011 no que respeita à restrição de utilização de determinadas substâncias perigosas existentes em equipamento eléctrico e electrónico.
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti: è conforme alla Direttiva 2011/65/UE del Parlamento Europeo e del Consiglio dell'8 giugno 2011 sulla limitazione dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche.
(SV) Vi garanterar på eget ansvar att denna produkt uppfyller och följer följande standarder och bestämmelser: uppfyller direktiv 2011/65/EU från Europeiska parlamentet och EG-rådet från den 8 juni 2011 om begränsningen av användning av farliga substanser i elektrisk och elektronisk utrustning.
(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat standardit ja säädökset: täyttää Euroopan parlamentin ja neuvoston 8. kesäkuuta 2011 päivätyn direktiivin 2011/65/EU vaatimukset koskien vaarallisten aineiden käytön rajoitusta sähkö- ja elektronisissa laitteissa.
(NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende standarder og regler: er i samsvar med EU-direktivet 2011/65/EU fra Europa-parlamentet og Europa-rådet, pr. 8 juni 2011, om begrensning i bruken av visse farlige stoffer i elektrisk og elektronisk utstyr.
(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser: er i overensstemmelse med direktiv 2011/65/EU fra Europa-Parlamentet og Rådet af 8. juni 2011 om begrænsning af anvendelsen af visse farlige stoffer i elektrisk og elektronisk udstyr.
(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előírásoknak: je v souladu se směrnící 2011/65/EU Evropského parlamentu a Rady EU ze dne 8. června 2011, která se týká omezení použití určitých nebezpečných látek v elektrických a elektronických zařízeních.
(CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami: Je v súlade s normou 2011/65/EÚ Európskeho parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých nebezpečných látok v elektrickom a elektronickom vybavení.

(SK) Výhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcímí normami a predpísmí: Je v súlade s normou 2011/65/EÚ Európske hov parlamentu a Rady z 8. júna 2011 týkajúcej sa obmedzenia používania určitých nebezpečných látok v elektrickom a elektronickom vybavení.
(SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom terpredpisom: je v skladu z direktivo 2011/65/EU Evropskega parlamenta in Sveta z dne 8. junij 2011 o omejevanju uporabe določenih nevarnih snovi v električni in elektronski opremi.
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach: jest zgodny z Dyrektywą 2001/65/UE Parlamentu Europejskiego i Rady z dnia 8 czerwca 2011 r. w sprawie ograniczenia stosowania niektórych niebezpiecznych substancji w sprzęcie elektrycznym i elektronicznym.
(LT) Prisiimdami visą atsakomybę deklaruojame, kad śis gaminys atitinka żemiau paminėtus standartus arba nuostatus: atitinka 2011 m. birželio 8 d. Europos Parlamento ir Tarybos direktyvą 2011/65/EB dėl tam tikrų pavojingu medžiagų naudojimo elektros ir elektroninėje jrangoje apribojimo.
(LV) Ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8. jūnija Direktīvai 2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu elektriskās un elektroniskās iekārtās.
(ET) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem: ir atbilstoša Eiropas Parlamenta un Padomes 2011. gada 8. jūnija Direktīvai 2011/65/ES par dažu bīstamu vielu izmantošanas ierobežošanu elektriskās un elektroniskās iekārtās.
(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive: este în conformitate cu Directiva 2011/65/UE a Parlamentului European și a Consiliului din 8 iunie 2011 cu privire la interzicerea utilizării anumitor substanțe periculoase la echipamentele electrice și electronice.
(HR) Izjavljujemo pod vlastitom odgovornošu da je strojem ukladan sa slijedešim standardima ili standardiziranim dokumentima i u skladu sa odredbama: usklađeno s Direktivom 2011/65/EU europskog parlamenta i vijeća izdanom 8. lipnja 2011. o ograničenju korištenja određenih opasnih tvari u električnoj i elektroničkoj opremi.
(SRL) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili normama: usaglašen sa direktivom 2011/65/EU Evropskog parlamenta i Saveta od 8.juna.2011. godine za restrikciju upotrebe određenih opasnih materija u električnoj i elektronskoj opremi.
(RU) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам: соответствует требованиям Директивы 2011/65/EU Европейского парламента и совета от 8 июня 2011 г. по ограничению использования определенных опасных веществ в электрическом и электронном оборудовании
(UK) На свою власну відповідальність заявляємо, що дане обладнання відповідає наступним стандартам і нормативам: задовольняє вимоги Директиви 2011/65/ЄС Європейського Парламенту та Ради від 8 червня 2011 року на обмеження використання деяких небезпечних речовин в електричному та електронному обладнанні.
(EL) Δηλώνουμε υπεύθυνα ότι το προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω κανονισμούς και πρότυπα: συμμοφρώνεται με την Οδηγία 2011/65/ΕΕ του Ευρωπαϊκού Κοινοβουλίου και του Συμβουλίου της 8ης Ιουνίου 2011 για τον περιορισμό της χρήσης ορισμένων επικύδυνων υσιών σε ηλεκτρικό και ηλεκτρονικό εξοπλισμό.
(AR) تيكلاتىشاميچوكتاو روياعىلە عم قغابوئي جىتنىلىا الله نأ ازنەج وانستكيلوىسەر عىلەن نذەن
(TR) Tek sorumlusu biz olarak bu ürünün aşağıdaki standart ve yönergelere uygun olduğunu beyan ederiz.

EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-11, EN 60335-1, EN 60335-2-79, EN 62233

2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU

Zwolle, 01-06-2016

H.G.FRosberg

CEO FERM B.V.

FERM B.V. - Lingenstraat 6 - 8028 PM - Zwolle - The Netherlands