CC91EP250 - Range hood Coldex - Free user manual and instructions

Product Type	Canopy Range Hood
Installation	Wall-mounted or under cabinet
Operating Modes	Extraction (ducted) and Recirculation (with charcoal filter)
Minimum Installation Height	650 mm above cooktop (check gas hob instructions for greater distance)
Air Discharge	Top or rear outlet, 100 mm diameter (120 mm on some models)
Motor Speeds	3 speeds (Low, Medium, High)
Lighting	1 x 28-40W incandescent bulb
Grease Filters	Metal self-supporting, washable in dishwasher; clean every 2 months
Charcoal Filter	Replace every 6 months (or more frequently with heavy use)
Power Supply	220-240V, 50Hz (as per rating plate)
Electrical Connection	Double pole switch with 3 mm contact gap; earth connection required for Class I
Controls	Mechanical slider switches for light and motor speeds
Safety Features	Automatic shut-off not specified; fire hazard warning; child safety; flambé cooking prohibited
Maintenance	Disconnect power before cleaning; use damp cloth and neutral detergent
Certification	CE marked

Frequently Asked Questions - CC91EP250 Coldex

What is the minimum installation height for the CC91EP250 range hood?

The minimum safety distance between the cooktop and the hood is 650 mm. However, if the gas hob instructions specify a greater distance, that must be followed.

Can I use the hood in recirculation mode?

Yes, the hood can be used in recirculation mode by fitting a charcoal filter and setting the conversion lever to the RECYCLING position. No ducting to the outside is required.

How often should I clean the grease filters?

The metal grease filters should be cleaned every 2 months of operation, or more frequently with heavy use. They are dishwasher safe.

How often should I replace the charcoal filter?

The charcoal filter cannot be cleaned and should be replaced at least every 6 months, or more often if the hood is used intensively.

What type of light bulb does the hood use?

The hood uses a 28W-40W incandescent bulb. To replace, remove the grease filters, unscrew the old bulb, and fit a new one with the same specifications.

How do I install the hood under a wall cabinet?

For predrilled cabinets, fix the hood using four 4.2 x 45 mm screws. For non-predrilled cabinets, position the hood and pilot drill 3.5 x 16 mm screws. Use the provided paper template if available.

Is it safe to use the hood with a gas hob?

Yes, but ensure the room has adequate ventilation to prevent backflow of exhaust gases. The negative pressure must not exceed 0.04 mbar. Also, maintain the minimum installation height.

What should I do if the power cord is damaged?

The power cord must be replaced by the manufacturer or its service agent to avoid hazard. Do not use the hood until repaired.

Can I connect the hood to an existing duct?

Yes, in extraction mode, connect the hood to the exhaust flue using a pipe of minimum 120 mm diameter. Do not connect to ducts carrying combustion fumes.

How do I switch between extraction and recirculation modes?

Open the metal grille panel and locate the conversion lever or knob on the centrifugal unit. Set it to DUCTING for extraction or RECYCLING for recirculation. For recirculation, also install the charcoal filter.

USER MANUAL CC91EP250 Coldex

Line drawing of a front-end air purifier with ventilation grilles and a circular vent (no text or symbols)

Instructions Manual

RECOMMENDATIONS AND SUGGESTIONS .... 3

GENERAL INFORMATION - SAFETY WARNINGS 4

INSTALLATION....5

USE 6

MAINTENANCE 7

INDICE

ES

RECOMMENDATIONS AND SUGGESTIONS

The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).
• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
• For Class I appliances, check that the domestic power supply guarantees adequate earthing. Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. The route of the flue must be as short as possible.
• Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.
• In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks.
• If the instructions for installation for the gas hob specify a greater distance specified above, this has to be taken into account. Regulations concerning the discharge of air have to be fulfilled.

USE

• The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
• Do not flambè under the range hood; risk of fire
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• “CAUTION: Accessible parts may become hot when used with cooking appliances.”

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
• Clean and/or replace the Filters after the specified time period (Fire hazard).
• Clean the hood using a damp cloth and a neutral liquid detergent.

Illustration of a kitchen appliance with a green X-shaped mark and a steaming pot (no text or symbols)

Illustration of a laboratory setup with a beaker and two flasks, intersected by a green ribbon (no text or symbols)

The symbol 📄 on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product,

GENERAL INFORMATION

This canopy hood is designed to be fixed to any rigid vertical surface, over a gas or electric hotplate and can be used either in the extraction mode (ducted to the outside) or in the recirculation mode (internal recycling). All cookers hood perform better when used in extraction mode. During winter time it may be convenient to use the hood in the recycling mode to avoid heat loss from the kitchen.

Before starting the installation, consideration should be given to the difficulties that can be found during installation. The installation work must be undertaken by a qualified and competent person in conformity to the rules concerning the evacuation of contaminated air.

The manufacturer disclaims all liability for any damage or injury caused as a result of not following the instructions for installation contained in the following text.

1 - SAFETY WARNINGS

1.1 - When used in the extraction mode, the cooker hood ducting must not be connected to a flue which is used for exhausting fumes from appliances supplied with energy other than electric, such as a central heating flue or water heating flue.
1.2 - Before connecting to the mains supply ensure that the mains voltage corresponds with the voltage on the rating plate inside the hood.
1.3 - Connect the cookerhood to the mains via a double poled switch which has 3mm clearance between the contacts.
1.4 - For cooker hoods featuring an earth cable, make sure the electric plant of your house is correctly earthed.
1.5 - Appliance in class II are provided with a double insulation; therefore do not connect them through earthed plugs but through a double poled plugs.
1.6 - When installed, the hood must be positioned at least 70cm above the hotplate.
1.7 - Never do flambé cooking under this cooker hood.
1.8 - Never leave frying pans unattended during use as overheated fat and oil may catch fire.
1.9 - Before carrying out any kind of maintenance or cleaning, disconnect the hood from the mains supply.
1.10- If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler then this must be of the room sealed or balanced flue type. If other types of flue or appliance are fitted, ensure that there is an adequate supply of air into the room. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.
1.11- The appliance must be positioned so that the plug is accessible.
1.12- If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
1.13- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
1.14- Children should be supervised to ensure that they do not play with the appliance.

2 - INSTALLATION INSTRUCTIONS

Some installation systems require the opening and removal of the metal grille panel.

2.1 - Instructions for opening and removing the metal grille panel

To open the grille panel, press inwardly on the two slider catches at each side of the grille panel and the grille will pivot down.

To remove the metal grille, pull forward on the right hand side so that the hinge pin on the back of the grille will be released from the slot in the side of the casing.

2.2 - Wall cabinet fixing

a - Predrilled wall cabinet: fix the hood onto the wall cabinet base panel using the four screws 4.2 x 45 mm (supplied with the fixing kit).

It is not necessary to open the metal grille.

b - No predrilled wall cabinet:

b.1 - If the hood is provided with a paper fixing template, follow the instructions.

b.2 - If the hood is not provided with a paper fixing template, position the hood on the wall cabinet base panel and pilot drill the 3.5 x 16 mm screws (not supplied with the fixing kit) from the inside onto the wood.

2.3 - Wall mounting

a - Drill two ∅ 8 mm holes on the wall using the paper template, insert two rawl plugs and two 4.2 x 44,4 mm screws leaving 5 mm untightened. Open the metal grille panel, hook the hood on and fully tighten the screws.

b - If the hood is not provided with a paper fixing template, drill two ∅ 8 mm holes (see draw.), insert the plugs and screws, proceeding as directed under paragraph a.

c - For wall mounting using wallbrackets (optional), follow the instructions of the fixing template.

d - Pay attention to the safety regulation of point 1.6.

2.4 - Choice of operating mode

a - Evacuation mode

To check that the hood is set up for evacuation, open the grille panel and make sure that the conversion lever or the change-over knob on the centrifugal unit is in the DUCTING position. The charcoal filter is not required.

For ducting to the outside, the hood is supplied with a rear and top outlet. A flange spigot of 100 mm diameter (120 mm in certain models) is usually fitted on the top outlet and a blanking plug on the rear outlet. If you choose to duct the hood from the rear of the casing, you should invert the position of the flange and of the blanking plug. Pay attention to the safety regulation 1.1.

b - Internal recirculation mode

To check that the hood is set up for recycling, open the grille panel and make sure that the conversion lever or the change-over knob on the centrifugal unit is in the RECYCLING position.

The charcoal filter is to be fitted. To fit the charcoal filter, support the filter with one hand and turn the thumb screw through the centre of the charcoal filter. If the filter is of the interlocking type, turn the filter clockwise. The hood can remain connected to the outside.

2.5 - Electrical connection and working test

1 - The safety measures 1.2, 1.3, 1.4 and 1.5 of paragraph 1 are to be strictly observed.

2- Once the electrical connection has been completed, check that the worktop illumination, motor and speeds work properly.

L Light Switches the lighting system on and off.

S	Led	Motor running led.
V1	Motor Switches the extractor motor on and off at low speed. Used to provide a continuous and silent air change in the presence of light cooking vapours.
V2	Speed	Medium speed, suitable for most operating conditions given the optimum treated air flow/noise level ratio.
V3	Speed	Maximum speed, used for eliminating the highest cooking vapour emission, including long periods.

Grease filters

CLEANING METAL SELF- SUPPORTING GREASE FILTERS

• The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.
• Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time.
• Wash the filters, taking care not to bend them. Allow them to dry before refitting.
• When refitting the filters, make sure that the handle is visible on the outside.

Hand holding a smartphone with a green arrow indicating left touch (no text or symbols)

CHARCOAL FILTER

In the recycling mode the charcoal filter absorbs smells and odours. The charcoal filter cannot be cleaned and should be replaced at least every six months or more frequently if the hood is used consistently.

To replace the charcoal filter, support the filter with one hand, remove the round disk through the centre of the charcoal filter and rotate it till the filter will come away.

Replace by reversing the operation.

Illustration of a hand holding a circular object with radial segments, enclosed in a circular frame (no text or symbols)

WARNING! It is a possible fire hazard if the filters are not cleaned and replaced as recommended.

Lighting

LIGHT REPLACEMENT

28W-40W light.

• Remove the metal grease filters.
• Unscrew the bulbs and replace them with new ones having the same characteristics.
• Replace the metal grease filters.

Line drawing of a hand holding a tool, no text or symbols present

Illustration of a kitchen appliance with a green X-shaped mark and a steaming dish, no text or symbols present.

Illustration of a laboratory setup with a pot and two inverted test tubes, intersected by a green X-shaped line (no text or symbols)

Illustration of a hand pressing a device with a green arrow indicating left motion (no text or symbols)

FILTRO AL CABON VEGETAL ACTIVO

Illustration of a hand holding a circular object with radial segments, enclosed in a circular frame (no text or symbols)

Line drawing of a hand holding a tool with a circular background (no text or symbols)

CE