50DR-5 - Power outlet Karlik - Free user manual and instructions

Product Type	Antenna Outlet Socket (RTV/RTV-SAT)
Brand	Karlik
Model	50DR-5
Compatible Box	60mm installation box
Cable Type	Coaxial antenna cable
Connection Type	Clamping bolt with blade
Pass-Through	Yes (input and output identical procedure)
Mounting Method	Spikes or fastening screws (box type dependent)
Installation	Qualified personnel only; deactivated voltage
Safety Standards	National safety standards compliant
Components Included	Socket, frame with cap, clamping bolt, mounting hardware
Application	RTV and RTV-SAT signal distribution
Assembly	Step-by-step instructions provided

Frequently Asked Questions - 50DR-5 Karlik

How do I prepare the coaxial cable for installation?

Strip the coaxial cable by cutting the external insulation, over-wrap, and center conductor at the same height. Refer to picture no. 1 in the manual for a visual guide.

How do I insert the cable into the socket?

Unscrew the clamping bolt, insert the cable so that the socket blade enters between the over-wrap and external insulation. Ensure the center conductor is correctly positioned in the input clamp (see picture no. 4).

What is the correct way to tighten the clamping bolt?

After inserting the cable, tighten the clamping bolt securely to hold the cable in place. Do not overtighten to avoid damage (picture no. 5).

How do I install the socket into a 60mm box?

Insert the socket into the 60mm installation box and use either the provided spikes or fastening screws depending on the box type to secure it.

Can I use this socket for pass-through wiring?

Yes, for pass-through sockets, the procedure for the socket output is the same as for the input. The socket supports both input and output connections.

What safety precautions should I take during installation?

Installation must be performed with deactivated voltage and by a suitably qualified person. All national safety standards must be met.

Who should perform the installation?

The installation must be carried out by a suitably qualified person with experience in electrical and antenna systems.

What tools are needed for installation?

You will need a wire stripper for coaxial cable, a screwdriver for the clamping bolt, and possibly a screwdriver or drill for mounting the socket into the box.

Does this socket work with all coaxial cables?

It is designed for standard coaxial antenna cables commonly used for RTV and RTV-SAT signals. Ensure the cable diameter is compatible with the clamping bolt.

How do I attach the frame and cap?

After mounting the socket, place the frame with the cap onto the main body of the outlet socket. It should snap or screw into place depending on the design.

USER MANUAL 50DR-5 Karlik

ASSEMBLY MANUAL OF RTV AND RTV-SAT OUTLET SOCKETS

1. Prepare end of the antenna cable for installation, i.e. strip the wire of the coaxial cable by cutting at the same height the external insulation, over-wrap and the centre of the cable. (picture no. 1)
2. Unscrew the clamping bolt in the antenna outlet socket (picture no. 2).
3. Insert the antenna cable so as blade of the socket enters between the over-wrap and the external insulation. Check if the wires of the cable are inserted into the input clamp in a correct way (picture no. 4).
4. Tighten the clamping bolt in the antenna outlet socket (picture no. 5).
5. For pass-through sockets - procedure for socket output is the same as for socket input.
6. Insert the socket into the 60mm installation box and according to the type of box assembly the socket with either the spikes or the fastening screws.
7. Place the frame with the cap on the main body of the outlet socket..

PICTURE NO.1

Mechanical assembly diagram showing a clamp holding a component (no text or symbols visible)

PICTURE NO.2

Mechanical component diagram showing a lever mechanism with no visible text or symbols

PICTURE NO.3

Mechanical assembly diagram showing a motor or gear mechanism with no visible text or symbols

PICTURE NO.4

Mechanical assembly diagram showing a lever mechanism with no visible text or symbols

PICTURE NO.5

NOTE!

Assembly shall be held by a suitably qualified person with deactivated voltage and shall meet the national safety standards.