LAN PCI Network Card 10/100 Mbps - Network card SWEEX - Free user manual and instructions

Product Type	Network Interface Card (NIC)
Interface	PCI (32-bit)
Network Speed	10/100 Mbps
Standards	IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX
Connector	RJ-45
Bus Standard	PCI 2.2
Data Transfer Rate	Up to 100 Mbps (half-duplex), 200 Mbps (full-duplex)
Dimensions	120 x 45 x 10 mm
Weight	50 g
Power Consumption	Less than 2 W
Operating Temperature	0°C to 50°C
Storage Temperature	-20°C to 70°C
Operating Humidity	10% to 90% (non-condensing)
LED Indicators	Link/Activity
Supported Operating Systems	Windows 98/ME/2000/XP/Vista/7, Linux, FreeBSD
Plug and Play	Yes
Compliance	FCC, CE
Warranty	2 years

Frequently Asked Questions - LAN PCI Network Card 10/100 Mbps SWEEX

How do I install the Sweex LAN PCI Network Card?

Turn off your computer, open the case, insert the card into an available PCI slot, close the case, and power on. Install the drivers from the included CD or download from the Sweex website.

Is this card compatible with Windows 10?

Sweex LAN PCI Network Card is designed for older Windows versions (98 to 7). For Windows 10, you may need to manually install drivers or use compatibility mode. Check the Sweex website for updated drivers.

What is the maximum speed of this network card?

The card supports 10/100 Mbps, but the actual speed depends on your network infrastructure (cables, switch, router). It does not support Gigabit (1000 Mbps).

Can I use this card with a Linux system?

Yes, the card uses a Realtek chipset (typically RTL8139) which has built-in Linux kernel support. It should work without additional drivers on most distributions.

How do I know if the card is properly recognized?

After installation, check Device Manager (Windows) or lspci (Linux). You should see a network controller listed. Also, the Link LED on the card should light up when connected to a network.

What should I do if my computer does not detect the card?

Ensure the card is firmly seated in the PCI slot. Try a different PCI slot. Check if the card is disabled in BIOS. Also, verify that you have installed the correct drivers.

Can I use this card in a PCI Express slot?

No, this card is designed for standard PCI slots (32-bit). PCI Express slots are different and physically incompatible. You would need a PCIe network card for those slots.

Does the card support Wake-On-LAN?

Yes, the Sweex LAN PCI Network Card supports Wake-On-LAN (WOL) if your motherboard and power supply also support it. You may need to connect the WOL cable (if included) to the motherboard.

How do I clean the network card?

Turn off the computer and unplug it. Use a soft, dry cloth to gently wipe the card. Avoid using liquids or abrasive materials. Ensure the gold contacts are clean by gently rubbing with a pencil eraser if needed.

What is the warranty period for this card?

Sweex offers a standard 2-year warranty for this LAN PCI Network Card. Keep your purchase receipt for warranty service.

USER MANUAL LAN PCI Network Card 10/100 Mbps SWEEX

First of all, many thanks for purchasing this Sweex LAN PCI Card. To ensure this product operates correctly, we advise you to carefully read this manual first. If despite this manual you still experience problems during installation or operation of this product, go to www.sweex.com and look under the heading service & support.

We advise you to ensure that the PC operating system is up-to-date before starting the installation. This is easy to check by starting up "Internet Explorer" and selecting the option "Windows Update" in the "Extra" menu. This Sweex LAN PCI Card is fully supported by Windows Microsoft®, Windows® XP, Windows Vista®, Windows® 7.

Package Contents

Prior to installation, check if all required parts are present. The following parts must be present in the box:

• 10/100 Network card PCI
- Quick installation guide
• CD with software, drivers, manual

If one of the above parts is missing, please contact the supplier.

Specifications

• Single-chip controller for PCI local bus revision 2.2
• Supports: 'Wake On LAN'(WOL) at PCI revision 2.2
• In accordance with 802.3 10BASE-T and IEEE802.3u 100 BASE-TX standard
• Realtek 8139 chipset
• Single shielded RJ-45 connector for use at 10 or 100 Mbps
• High performance bus master structure for low CPU and bus usage
• Supports: ACPI and PCI power management
• 1 diagnosis LED for link status and data transfer
• Supports: Windows Microsoft®, Windows® XP, Windows Vista®, Windows® 7

Installation of hardware

Take the following precautionary measures prior to installing the hardware:

• Ensure the PC is switched off and not connected to the mains or any other power supply.
• Also, disconnect the printer and monitor cables (they have their own power supply) to make absolutely sure that the PC is not live.
  • Now unscrew the computer casing.
• Subsequently, remove any static electricity you may carry on your body. Do this by touching a (neutral) pipe of the central heating system or an unpainted water pipe, among other things. Please note that you must not use a magnetic screwdriver for this. Before you proceed any further, shortly touch the iron frame of the PC casing. Make sure that you minimise contact with any contact points of the PC Card or the memory.
• Find a vacant PCI slot and remove the metal guard plate part of the computer casing in front of the relevant slot. On occasion the card does not allow to be inserted in the PCI slot smoothly. Should this be the case, do not force anything, but try another available slot.
• Once the card has been successfully installed, check whether all other cards are still properly inserted in the PCI slots. It is possible that the other PCI cards are lifted up slightly when installing a new PCI card; as a result, the relevant cards or even the entire PC may no longer operate correctly.
• Replace the casing on the computer base and correctly reconnect all cables.
• Switch on the PC again.

Installation Windows Microsoft®, Windows® XP, Windows Vista®, Windows® 7

Start the PC once the hardware installation has been completed. Windows will automatically detect the Sweex LAN PCI Card 10/100 Mbps. No drivers are required for installation under Microsoft® Windows® XP, Windows Vista®, Windows® 7 as they are all present within the operating system, provided it is up-to-date. If Windows nevertheless indicates that the hardware must be installed, follow the following procedure:

Click 'Next' in the corresponding screen which will appear automatically. Now select the option 'Search for the best driver' and click 'Next'. In the next screen, select the CD-ROM Driver as the location for the search to be carried out. Windows will locate the driver on the CD-ROM (if not, it can also be found on the CD-ROM — Drivers via 'Specify a location'. Subsequently, select 'Use the updated driver' and click 'Next'. The hardware has been installed successfully and is ready to be used.

If you experience an issue that is not listed in this manual, please consult the frequently asked questions section of your product on the sweex.com website.

Sweex warranty conditions

2-year standard warranty within the EU

In a standard manner a warranty period of 2 years as from the purchase date is available for this Sweex product within the EU.

Should you wish to invoke this warranty within the first 2 years after the purchase then you can directly apply to the point of sale where you purchased the product for the conditions and procedures.

10-year manufacturer's warranty

However, in addition to the statutory 2-year standard warranty Sweex offers you an extended quality warranty of no less than 10 years, if you purchased your product within the EU.

For more information, conditions and the registration form go to www.sweex.com/12yearswarranty and register within 30 days after the purchase of your product for the extended warranty period of in total 12 years.

Matters that are excluded from the warranty

The warranty of Sweex only covers manufacturing defects. Excluded from the warranty are accessories like batteries, rechargeable batteries and also supplied software, where applicable.

The liability of Sweex is limited to the costs of repair and/or replacement of the product covered by the warranty.

The standard warranty is null and void if the product has been opened, changes have been made, physical damage was caused to the product and if the product is used for another purpose than for which it is originally meant.

All brand names and associated rights mentioned in this manual are and remain the sole property of the rightful claimant.