CD-8MLAN - CD Player YAMAHA - Free user manual and instructions

USER MANUAL CD-8MLAN YAMAHA

This product, when installed as indicated in the instructions con- tained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instuctions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class " digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in à residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instruc- tions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC

FCC INFORMATION (U.S.A.) regulations does not guarantee that interference will not occur in allinstallations. If this product is found to be the source of inter- ference, which can be determined by tuming the unit "OFF" and “ON”, please ty to eliminate the problem by using one of the following measures Relocate either this product or the device that is being affected by the interference Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s In the case of radio or TV interference, relocate/reorient the an- tenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable. Ifthese corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Divi- Sion, 6600 Orangethorpe Ave, Buena Park, CA90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

& SP) CDB(E).book Page3 Friday, October 6, 2000 3:22PM À WARNING À CAUTION Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: + Do not attempt to disassemble or modify the card. Do not apply excessive force to card connectors or other card compo- nents. Mishandling of the card may lead to shock, fire hazard, or equipment failure. + Be sure to disconnect the power cable of the main unit before installing this card (in Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following: + The card is sensitive to static electricity. Before handling the card, you should briefly touch the metal casing of the main unit with your bare hand to discharge any static charge from your body. Failure to do so may damage the card. + Do not touch the metallic leads (pins) of the

English order to eliminate shock hazard). circuit board when handling the card. The pins are sharp and may cause hand cuts. Yamaha cannot be held responsible for data loss or equipment damage caused by inappropriate handling or use. INSTALLATION Please refer to the owners manual of the main unit for information about how to install the card. (If information is not provided, please consult your Yamaha dealer.) NOTE) You will need to setthe DIP switches according to your application. Before you install the card, refer to “DIP switch settings” (p.10) CD8-mLAN Installation Precautions + Before beginning installation, switch off the power to the main unit and any connected periph- erals, and unplug them from the power outlet. Then remove all cables connecting the main unit to other devices. (Leaving the power cord connected while working can result in electric shock. Leaving other cables connected can interfere with the installation procedure.) + _Itis recommended that you wear gloves to protect your hands from sharp or pointed projec- tions on the equipment. + Board components may be damaged by electrostatic discharge. Be sure to drain any electro- static charge from body and clothes before starting work. Keep hands clear of board compo- nents, board circuitry, and metallic leads while carrying out the installation. + Handle the plug-in boards with care. Dropping or subjecting the card to any kind of shock may cause damage or result in a malfunction. + Do not touch the exposed metal parts in the circuit board. Touching these parts may result in a faulty contact. + Take care to avoid dropping screws into the main unit. If a screw does fall in, be sure to remove it before you reassemble and power up the unit. Starting the unit with a loose screw inside may lead to improper operation or to equipment failure. (If you are unable to retrieve a dropped screw, consult your Yamaha dealer for advice.)

& SP) CDB(E).bock Page4 Friday, October 6, 2000 3:22PM @7 (2 Introduction Thank you for purchasing the Yamaha CD8-mLAN. The CD8-mLAN is an interface card that provides mLAN interfacing. mLAN is a digital network designed for music and based on the IEEE 1394 high performance serial bus. MLAN makes it easy to construct sophisticated networks for audio and MIDI signals that can be re-configured without changing the physical cabling (as was necessary with previous systems). The CD8-mLAN adds two mLAN connectors to the Yamaha 02R or 03D digital recording consoles. For details on installing the interface card, refer to the owner’s manual of the device in which the card is being installed. English Package Contents + CD8-mLAN + _mLAN Tools (CD-ROM) + IEEE 1394 cable (4.5 m) + _Owner’s manual (this document) MLAN guidebook r + mLAN Tools installation guide

About the included CD-ROM The included CD-ROM contains software that is useful when used in conjunction with the CD8-mLAN. The software includes “mLAN Patchbay” which allows audio /MIDI signal routing between electronic musical instruments connected to the CD8-mLAN to be con- trolled from your computer. For details refer to the separate “mLAN Tools Installation Guide.” Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed. The illustrations shown in this Owner's Manual are for instructional purposes only, and may appear somewhat different from those on your device. The company names and product names in this Owner's Manual are the trademarks or registered trademarks of their respective companies.

@ T Names and Functions @) © D £ nf = O O En) f D] U L— "+ LI ä CS rQe| (ÉÈ KLY 2 1 ==, —©O co ACTIVE @YAMAHA mMLAN Interface Card MODEL CD8-mLAN EEE1394 MADE IN JAPAN @ SERIAL 1/0 jack This jack is used to connect the CD8-mLAN directly to a personal computer via a serial cable. Use this jack to connect the CD8-mLAN and the computer when you are using the mLAN Patchbay and mLAN Mixer on Windows. This is not used to input or output MIDI and audio signals. Refer to page 7 for more information on the connections. | O) © > mLAN (IEEE1394) jacks @ These jacks are used to connect mLAN devices or IEEE1394-compatible devices via IEEE1394 stan- Î dard (6-pin) cables. Each jack has an LED in the upper left corner to indicate the following statuses. green: The CD8-mLAN or connected device is a “leaf” node. off : Not connected. red : Ifthe cable is disconnected, the sound will be interrupted on a connected device or other device.

This LED indicates the following statuses. green: The CD8-mLAN is a “root.” orange : An error has occurred. (IEEE1 394 bus-related) red : An error has occurred. (Other errors) off : Status other than above. NOTE) Refer to “LED Messages” on page 11 for information on the error indication. ACTIVE LED This LED indicates the following statuses. blue : The relay function is active. off : The relay function is disabled.

NOTE) Since the CD8-mLAN will stop functioning as a bus relay when the power of the main unit is turned off, this LED will also correspond to the power on {lit blue) or off (dark) status.