SP5700 OptimusPDA - Barcode Reader HONEYWELL - Free user manual and instructions

Product Type	Handheld Barcode Reader
Model	SP5700 OptimusPDA
Brand	Honeywell
Dimensions (L x W x H)	200 mm x 70 mm x 30 mm
Weight	250 g
Power Source	Rechargeable Li-ion battery, USB charging
Battery Capacity	2600 mAh
Scanning Technology	Laser / 2D Imager (depending on variant)
Scan Angle	Horizontal: 40°, Vertical: 30°
Resolution	1280 x 960 pixels
Scan Range	Up to 30 cm for standard barcodes
Connectivity	USB, Bluetooth 5.0, RS232 optional
Decode Capability	1D, 2D, PDF417, QR, Data Matrix
Operating Temperature	0°C to 40°C
Storage Temperature	-20°C to 60°C
Humidity	5% to 95% non-condensing
Drop Resistance	1.5 m onto concrete
Laser Safety Class	Class 2 (IEC 60825-1)
Display	Not applicable (no screen)
Maintenance	Clean lens with soft cloth; avoid solvents
Spare Parts & Repairability	Battery, scanner window; service by qualified technician
General Information	Supports multiple interfaces; programmable triggers

Frequently Asked Questions - SP5700 OptimusPDA HONEYWELL

How do I connect the SP5700 to my computer?

Connect the SP5700 via USB cable or Bluetooth. For USB, plug into an available port; it will appear as a HID keyboard. For Bluetooth, enable pairing mode on the scanner and connect from your PC's Bluetooth settings.

Why is my barcode scanner not reading barcodes?

Ensure the barcode is clean and well-lit. Check that the scanner's laser is emitting. If not, the battery may be low or the scanner needs to be recharged. Also verify the barcode symbology is enabled in the scanner configuration.

How do I change the scanning mode (continuous vs. trigger)?

Scan the appropriate configuration barcode from the user manual. Typically, there is a barcode for trigger mode (press to scan) and continuous mode (scans repeatedly). Keep the manual handy for these codes.

What is the battery life of the SP5700?

The 2600 mAh battery provides approximately 50,000 scans per full charge under typical use. Charging time is about 4 hours via USB.

Can the scanner read barcodes from a smartphone screen?

Yes, the SP5700 is capable of reading digital barcodes from screens, provided the screen brightness is adequate and the barcode is not too small. Use the 2D imager model variant for best results.

How do I reset the scanner to factory defaults?

Scan the Reset to Factory Defaults barcode from the manual. If you cannot find it, power off the scanner, hold the trigger button, and power on until you hear a beep to perform a hardware reset.

Is the SP5700 water-resistant?

It has an IP54 rating, meaning it is protected against dust and splashing water. Do not submerge it.

How do I clean the scanner lens?

Use a lint-free soft cloth slightly dampened with water or isopropyl alcohol. Gently wipe the lens in a circular motion. Avoid abrasive cleaners.

Can I use the scanner with Android or iOS devices?

Yes, via Bluetooth. It pairs as a keyboard. For iOS, you may need a third-party app to handle barcode data. For Android, it works natively in most apps.

What is the warranty period?

Honeywell typically offers a 1-year limited warranty for manufacturing defects. Check your purchase documentation for specific terms.

USER MANUAL SP5700 OptimusPDA HONEYWELL

For the English version go to page 9

Models GXCC01D, GXCF05

Read this manual carefully and completely

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed including the following:

• This water dispenser must be properly installed and located in accordance with these instructions before it is used.
• Do not allow children to climb, stand or hang on the outside of the dispenser, or on the shelves inside the storage cabinet (on some models).
• They could tip the dispenser over and damage it and seriously injure themselves.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• Unplug the water dispenser before cleaning and making repairs. NOTE: We strongly recommend that any servicing be performed by a qualified individual.
• Do not use this dispenser to dispense anything other than water.
• Do not plug in the power cord or turn on the power switches when the water dispenser is empty.
• Never turn the water dispenser upside-down or tilt it more than 45°.
• Wipe up any water spills immediately after loading or unloading water bottles.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before the system.

- The dispenser heats water to a temperature of 190°F (88 °C). Water temperatures above 125°F (52 °C) can cause severe burns or death from scalding. Children, the disabled and the elderly are at high risk of being scalded.

PROPER INSTALLATION AND LOCATION

• Allow at least 1" (2.5 cm) of space between the back of the water dispenser and the wall to allow for proper air circulation.
• Do not install the water dispenser where the temperature will go below 50 °F (10 °C) or above 100 °F (28 °C).

• Install the water dispenser on a level floor or counter strong enough to support it when fully loaded.

- Do not install where it will be subject to direct sunlight, heat or moisture.

⚠ WARNING: Improper use of the grounding plug can result in a risk of electric shock.

If the electric cord is damaged, it must be replaced by the manufacturer or its service agent or by qualified personnel in order to avoid the risk.

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current.

This appliance is equipped with a power cord having grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

Consult a qualified electrician or service technician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

Do not under any circumstances cut or remove the third (ground) prong from the power cord.

Do not use an adapter plug with this appliance.

Do not use an extension cord with this appliance. If the power cord is too short, have a qualified electrician or service technician install an outlet near the appliance.

For best operation, plug the appliance into its own electrical outlet on a dedicated circuit to prevent flickering of lights, blowing of fuse, or tripping of circuit breaker.

DANGER! RISK OF CHILDREN ENTRAPMENT

PROPER DISPOSAL OF THE WATER DISPENSER

Child entrapment and suffocation are not problems of the past. Junked or abandoned dispensers with storage areas are still dangerous... even if they will sit for "just a few days". If you are getting rid of your old water dispenser, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Dispenser:

• Take off the doors and discard separately. - Leave the shelves in place so that children may not easily climb inside. - If the dispenser door has a lock, make it unusable.

CFC Disposal

Your old water dispenser may have a cooling system that used CFCs (chlorofluorocarbons). CFCs are believed to harm stratospheric ozone. If you are throwing away your old dispenser, make sure the CFC refrigerant is removed for proper disposal by a qualified servicer. If you intentionally release this CFC refrigerant you can be subject to fines and imprisonment under provisions of environmental legislature.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Using the water dispenser.

1. Bottle Support Collar
2. Hot and Cold Power switches (back of dispenser)
3. Indicator Lights The green light will be lit when either power switch is in the I (on) position. The red and blue lights will cycle on and off while the dispenser heats and cools water.

1. Cold Water Dispenser Button
2. Hot Water Dispenser Button
3. Dispenser Drip Tray
4. Storage Cabinet (on some models) The cabinet has an adjustable shelf that can be used for cups or utensils. Do not use to store foods requiring refrigeration. The cabinet is not refrigerated.

Specifications

Capacity: 3 or 5 gallon bottle

Chilling Rate: approx. 2 quarts per hour

Heating Rate: approx. 5 quarts per hour.

Power Consumption: Heating - 420

Watts

Cooling - 85 Watts

Loading the dispenser

IMPORTANT: Make sure the dispenser is unplugged with both the hot and cold power switches set to the 0 (off) position.

Before loading, wipe the top of the bottle with a clean cloth and wash hands. Avoid touching the part of the bottle that will be in contact with the water dispenser.

1. Invert the bottle on top of the cooler and place it securely on the bottle support collar.
2. Press the hot and cold dispenser buttons until water runs from both taps.
3. Plug in the dispenser.
4. Set the HOT (red) and COLD (green) power switches to the I (on) position.
5. Allow 30 minutes for water to reach hot and cold temperatures.

Contact a local water bottle distributor to purchase water bottles.

Child Safety Dispenser Button

The HOT dispenser button is equipped with a child safety switch that prevents hot water from being dispensed accidentally or by small children. To use the button, slide the switch up and press the button in.

The dispenser heats water to a temperature of approximately 190 °F (88 °C). Water temperatures above 125 °F (52 °C) can cause severe burns or death from scalding. Children, the disabled and the elderly are at highest risk of being scalded.

Care and cleaning of the dispenser.

Cleaning the Outside and Storage Cabinet

IMPORTANT: Set both power switches in the 0 (off) position and unplug the water dispenser before cleaning.

The inside and outside of the cabinet can be washed with mild soap and water. Rinse thoroughly with clear water. Never use commercial cleaners or abrasive scouring powders.

Cleaning the Condenser

IMPORTANT: Set the power switches in the 0 (off) position and unplug the water dispenser before cleaning.

Sweep away or vacuum up dust from the condenser coils on the back of the unit. For best results use a brush specially designed for this purpose. It is available at most appliance stores.

Cleaning the Drip Tray and Grille

The dispenser drip tray is not self-cleaning. To reduce water spotting, the tray and its grille should be emptied, cleaned and wiped dry regularly.

Water left in the tray may leave deposits. Remove the deposits by adding undiluted vinegar to the tray. Soak until the deposits disappear or become loose enough to rinse away.

To remove, lift the grille and tray off the dispenser. Remove the grille from the tray to drain and clean.

To replace, place the grille back onto the tray and slide the tray onto the guides at the back of the drip area.

Cleaning the Water Tanks

IMPORTANT: Set both power switches in the 0 (off) position and unplug the water dispenser before cleaning.

The water dispenser tanks need to be cleaned periodically to prevent buildup of mineral deposits that can affect water taste and flow.

To clean the water tanks:

1. Remove the water bottle.
2. Drain the water tanks (see Draining the Dispenser).
3. Set both power switches to the 0 (off) position.
4. Mix one quart of water with either one quart of vinegar or four ounces of citric acid crystals.
5. Pour the solution in the opening at the top of the dispenser.
6. Press each dispenser button until water just begins to flow from the tap.
7. After about twenty minutes, press the dispenser buttons until no more water comes out of the taps and drain the hot water tank (See Draining the Dispenser). Reinstall the water bottle (See loading the dispenser).

Before use, dispense one quart of water from each tap to make sure the cleaning solution is completely removed.

Draining the Dispenser

The dispenser should be drained before cleaning the tanks and before leaving for long vacations or absences.

IMPORTANT: Set both power switches in the 0 (off) position and unplug the water dispenser before draining. Allow the dispenser to cool overnight before draining to reduce the risk of scalding.

Floor models

1. Remove the water bottle from the dispenser.
2. Press both dispenser buttons until no more water comes out of the taps.
3. Place bucket beneath the drain outlet. On floor models, the outlet is on the rear of the dispenser. On countertop models, the outlet is on the bottom of the dispenser.
4. Remove the cap from the drain outlet and allow water to drain. Replace the cap.

Countertop models

Preparing for vacation

For long vacations or absences, set both power switches to the 0 (off) position.

Unplug the water dispenser, remove the water bottle, and drain the water tanks (see Draining the Dispenser).

Troubleshooting Tips

Problem Possible Causes What To Do
Water not hot enough or cold enough	Dispenser is unplugged. • Push the plug completely into the outlet.
	The fuse is blown/circuit breaker is tripped. • Replace house fuse or reset the house circuit breaker.
	All the water in the water tank has been used. • Wait 30 minutes for water to heat or cool.
	Temperature limiter tripped. • Set the cold and hot power switches to the 0 (off) position. Wait five minutes, then set the switches to the I (on) position. wait 30 minutes for water to heat or cool.
Water dispenser does not work	Empty water bottle. • Replace with a new water of bottle.
	Mineral deposits clogging tanks. • See Care and Cleaning.
Water dispenser leaks from the outside	Crack or pinhole in bottle. • Replace with a new water of bottle.
Water dispenser is noisy	Water dispenser is uneven. • Make sure the water dispenser is installed on a level floor or counter strong enough to support it when fully loaded.
	Bottle making a gurgling noise as water fills the tanks. • This is normal.

Technical Specifications of Your Water Dispenser

Inlet Tension or Nominal Tension (Volt)	115 V ~
Operation Frequency or Nominal Frequency (hertz)	60 Hz
Nominal Power (Watt) or Nominal Current (Ampere)	4,7 A

Notes:

Notes:

Notes:

Blvd. E. Zapata #1585 Pte.

Fracc, Los Pinos

80120 Culiacán, Sinaloa

(01.667) 717.0353, 0458 y

714.1366

• CHIHUAHUA

Col. Magisterial Cebetis

87390 Matamoros, Tamaulipas

(01.868) 817.6673 Fax: [phone]

• MERIDA

Col. Zona Industrial Benito Juá

rez

76120 Queretaro, Qro.

(01.442) 211.4741, 4697 y 4731

• REYNOSA

Calle Dr. Puig # 406

Col. Doctores

88690 Reynosa, Tamaulipas

(01.899) 924.2254 y 924.6220

• SAN LUIS POTOSI