S1 - Microphone RODE - Free user manual and instructions

Product Type	Live condenser microphone
Brand	RØDE
Model	S1
Acoustic Principle	Pressure gradient
Polar Pattern	Supercardioid
Frequency Range	20 Hz - 20 kHz
Sensitivity	-46 dB re 1 Volt/Pascal (5 mV @ 94 dB SPL) ± 2 dB @ 1 kHz
Output Impedance	50 Ω
Equivalent Noise	18 dB SPL (A-weighted per IEC651)
Maximum SPL	151 dB SPL (@ 1kHz, 0.7% THD into 1kΩ load)
Dynamic Range	132 dB (per IEC651, IEC268-15)
Signal/Noise Ratio	75 dB SPL (A-weighted per IEC651)
Power Requirement	P48 (48V) phantom supply
Output Connection	3-pin XLR
Weight	308 g
Construction	Rugged all-metal with satin nickel/black finish
Head	Heat-treated high strength mesh with internal plosives screen
Accessories Included	RM1 stand mount, ZP1 zip pouch
Warranty	1 year standard; 10 years with online registration
Country of Origin	Australia
Maintenance	Wipe with soft dry cloth; mesh head washable with soap and water
Storage	Store in protective case with moisture-absorbent crystals (reusable by drying)

Frequently Asked Questions - S1 RODE

What type of power does the RØDE S1 require?

The RØDE S1 requires 48V phantom power (P48) from a mixing console, PA head, or other source.

What is the polar pattern of the S1?

The S1 has a supercardioid polar pattern, which provides excellent rejection of off-axis sound and feedback.

How do I clean the mesh head of the S1?

The mesh head can be unscrewed and washed in soap and water. Ensure it is fully dried before reassembly.

Can I use the S1 without phantom power?

No, the S1 is a condenser microphone and requires 48V phantom power to operate. It will not work without it.

How can I reduce feedback when using the S1?

Avoid covering the ball head with your hands, and do not point the front of the mic at speakers. Position stage monitors as shown in the manual to direct sound to the least sensitive area of the polar pattern.

What is the warranty period for the RØDE S1?

The S1 comes with a 1-year warranty that can be extended to 10 years by registering the product online at www.rodemic.com.

How should I store the S1 when not in use?

Wipe the microphone with a dry soft cloth and place it in its protective case. Include the moisture-absorbent crystals at the head of the mic. Dry the crystals in an oven at 100-150°C for about 10 minutes when they turn pink.

What accessories are included with the S1?

The S1 includes an RM1 stand mount and a ZP1 zip pouch for storage.

What is the sensitivity of the S1?

The sensitivity is -46 dB re 1 Volt/Pascal (5 mV @ 94 dB SPL) ± 2 dB @ 1 kHz.

Is the RØDE S1 made in Australia?

Yes, the S1 is made in Australia by RØDE Microphones.

USER MANUAL S1 RODE

Close-up of a gray audio recording device with mesh grille and label 'RODE S1 100' (no additional text or symbols visible)

www.rodemic.com

Introduction

The S1 is the result of over 30 years experience in stage sound technology.

The design brief was simple- build the best vocal mic in the world! How do you achieve that? Well, you need to have a sound quality that is equal to the fi nest studio microphones, and certainly RODE has the experience to make this happen!

The studio quality is a great start, but for live use the microphone must not suffer from feedback, handling or plosive noise. It must also have a tailored response that takes into consideration the proximity effect. What else? It must be able to take the knocks and bumps of the road! The S1 does it all, and in my opinion, is the best looking vocal mic around.

While using the S1 is quite simple, and there are not many things you need to learn, please take a moment to read through this user manual, and then visit www.rodemic.com and register your microphone for a full ten year warranty.

While there you can view studio tips and techniques, as well as browse the comprehensive range of accessories for RODE microphones. Thank you for investing in your S1 live condenser microphone.

Peter Freedman

R∅DE Microphones

Sydney Australia

Specifications

Acoustic Pressure gradient

Principle:

Directional Super Cardioid

Pattern: (See graph)

Frequency 20 Hz - 20 kHz

Range: (see graph)

Output 50Ω

Impedence:

Sensitivity: -46 dB re 1 Volt/Pascal (5 mV @

94 dB SPL) +/- 2 dB @ 1kHz

Equivalent Noise: 18 dB SPL

(A - weighted per IEC651)

Maximum +12.5dBu (@ 1kHz, 0.7% THD

Output: into 1KΩ load)

Dynamic Range: 132 dB

(per IEC651, IEC268-15)

Maximum SPL: 151dB SPL (@ 1kHz, 0.7% THD

into 1KΩ load)

Signal/Noise: 75 dB SPL

(A - weighted per IEC651)

Power P48 (48V) phantom supply

Requirement:

Output 3-Pin XLR

Connection:

Net Weight: 308gm

Specifications

Frequency Response

Polar Response

Accessories

Black leather pouch with embossed logo (no readable text or symbols)

RM1 Stand mount ZP1 Zip pouch

Features

• Studio recording-quality specification
• Supercardioid polar pattern
• Rugged all-metal construction
- Attractive satin nickel/black fi nish.
• Heat treated high strength mesh head
- Custom designed internal plosives screen
- Low handling noise
• Made in Australia
• 10 Year warranty*

Black RODE 51 audio recording device with mesh grille and microphone (no visible text or symbols on body)

*Online product registration required.

Using the S1

- The S1 is a phantom powered microphone. To operate correctly it requires a 48V phantom supply from the mixing console, PA head or other source.

- It is recommended that you use a high-quality microphone lead, and keep it as short as practical for your stage set up. This will ensure the highest quality sound reproduction.

- When using stage monitors, set them up as shown below. This will direct the sound to your ears and towards the least responsive part of the S1's pick up pattern.

Black-and-white photo of a microphone setup with a tripod stand and a small mechanical component, no visible text or symbols.

While PA set up is well beyond this manual, if you want to get the best sound possible with the least problems, we recommend a book by Australian audio legend Duncan Fry, titled "Live Sound Mixing".

A quick tip to reduce feedback - never put your hands over the ball head. This can signifi cantly change the pick-up area of the mic, and can cause feedback. And of course, never point the front of mic at the speakers!

- The ball head of the S1 is an engineering marvel. Made up of fi ve separate mesh screens the outer is heat-treated steel, which has been bead-blasted and nickel-plated. Internally we have stainless steel meshes as well as a fi nal nylon mesh. These fi lters are design to remove vocal plosives, while not affecting the frequency response. The mesh head can be unscrewed and washed in soap and water. Please fully dry the head before re-assembly and be sure to take care with the mic once the head has been removed.

Storage

• After use the S1 should be wiped with a dry, soft cloth and placed in its protective case.
• Be sure to place the moisture-absorbent crystals (supplied) at the head of the microphone, so as to absorb any moisture present.
• Eventually this pack of crystals will need to be dried. This is indicated by the crystals turning pink in colour.
• They can easily be re-used by placing them in an oven at 100 - 150 degrees celsius for approximately ten minutes. The crystals will operate effectively again once they have turned blue.

Warranty

All RODE phones are warranted for one year from date of purchase. You can extend that to a full ten years if you register online at www.rodemic.com.

The warranty covers parts and labour that may be required to repair the microphone during the warranty period. The warranty excludes defects caused by normal wear and tear, modification, shipping damage, or failure to use the microphone as per the instruction guide.

If you experience any problem, or have any questions regarding your RODE microphone, first contact the dealer who sold it to you. If the microphone requires a factory authorised service, return will be organised by that dealer.

We have an extensive distributor/dealer network, but if you have difficulty getting the advice or assistance you require, do not hesitate to contact us directly.

R∅DE Microphones

International

PO Box 6685

Silverwater NSW 2128 Australia

Ph: [phone]

Fax: [phone]

USA

P.O. Box 4189

Santa Barbara, CA 93140-4189

Ph: 805 566 7777

Fax: [phone]

Technical Support

For information and technical support questions contact:

[e-mail]

In the United States and Puerto Rico, contact

[e-mail] or call 425 398-1910

In Australia, contact [e-mail] or call [phone]

Anywhere except Australia, the United States and Puerto Rico,

contact [e-mail] or call [phone]