VT-81010 - Motion detector V-TAC - Free user manual and instructions

Product Type	Infrared Motion Sensor
Model	VT-81010
SKU	23426
Input Voltage	AC 220-240V, 50/60 Hz
Rated Load	Max 1200W (600W LED)
Power Consumption	Approx. 0.9W
Detection Angle	360°
Detection Distance	8m max (<24°C)
Detection Speed	0.6-1.5 m/s
Time Delay	Min 10 sec ±3 sec, Max 15 min ±2 min
Ambient Light Setting	3-2000 LUX (adjustable)
Working Temperature	-20°C to +40°C
Working Humidity	<93% RH
IP Rating	IP20
Installation Height	1.8-4m
Cutout Size	∅63-66mm
Dimensions	∅76 x 49 mm
Warranty	5 years
Compatibility	V-TAC LED range (up to 600W)
Installation Environment	Indoor use only

Frequently Asked Questions - VT-81010 V-TAC

How do I test the sensor after installation?

Turn the TIME knob anti-clockwise to minimum (10s) and the LUX knob clockwise to maximum (sun). Switch on power; after a 30-second warm-up, the sensor will activate. When it detects motion, the lamp turns on and turns off after 10 sec ±3 sec if no further motion.

Why doesn't the lamp turn on?

Check the power and load connections. Ensure the load is functional. Verify that the LUX setting matches the ambient light (if set to low, it may not work in daylight). Also, check for any obstructions blocking the sensor.

How do I adjust the ambient light sensitivity?

Turn the LUX knob clockwise to work in bright conditions (sun symbol) or anti-clockwise to work only in darkness (3 LUX). For daytime testing, set to the sun position.

What is the detection range of the sensor?

The sensor has a 360° detection angle and a maximum detection distance of 8 meters at temperatures below 24°C, suitable for installation heights of 1.8-4 meters.

How to set the time delay?

Adjust the TIME knob to set the duration the lamp stays on after detection. Minimum is 10 sec ±3 sec and maximum is 15 min ±2 min. The timer restarts if motion is detected again.

Why does the sensor keep triggering or stay on?

Possible causes: continuous motion in the detection area, the time delay set too high, or the sensor pointed at a heat source (e.g., air vent, heater). Check for moving objects like curtains or pets.

Can I use this sensor outdoors?

No, this sensor has an IP20 rating and is designed for indoor use only. Do not install it outdoors or in damp areas.

What is the maximum load for LED bulbs?

The sensor can handle a maximum load of 600W for LED bulbs. For other types, the maximum is 1200W. Ensure the connected lamp does not exceed these ratings.

How do I install the sensor?

Switch off power. Remove the transparent cover. Connect wires according to the wiring diagram. Replace the cover. Fold the metal spring, insert into a cutout (∅63-66mm), and release the spring to secure. Turn power on and test.

How long is the warranty?

The product comes with a 5-year warranty from the date of purchase, covering manufacturing defects. It does not cover damage from incorrect installation or abnormal wear.

USER MANUAL VT-81010 V-TAC

WEEE Number: 80133970

INSTRUCTION MANUAL

INFRARED MOTION SENSOR

TECHNICAL DATA

MODEL VT-81010
SKU 23426
INPUT VOLTAGE AC: 220-240V, 50/60 Hz
RATED LOAD	Max. 1200Wn600W +LED
TIME DELAY	Min. 10sec ±3secMax. 15min ±2min
DETECTION RANGE	360°
DETECTION DISTANCE	8m Max (<24°C)
DETECTION MOTION SPEED	0.6-1.5m/s
WORKING TEMPERATURE	-20°C to +40°C
WORKING HUMIDITY	<93%RH
POWER CONSUMPTION	Approx, 0.9W
AMBIENT LIGHT <3-2000 LUX (Adjustable)

White ceiling-mounted LED fixture with blue handle and control knobs, no visible text or symbols on the component itself.

COMPATIBLE WITH

V-TAC LED

RANGE (UPTO 600W)

05 YEAR

WARRANTY*

IP RATING	IP20
INSTALLATION HEIGHT	1.8-4m
CUTOUT SIZE	∅63-66m
DIMENSION	∅76x49 mm

INTRODUCTION & WARRANTY

Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any another query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 5 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product.

Caution, risk of electric shock.

MULTI-LANGUAGE MANUAL QR CODE

Please scan the QR code to access the manual in multiple languages.

This marking indicates that this product should not be disposed of with other household wastes.

FR

1. Please make sure to turn off the power before starting the installation.
2. Installation must be performed by a qualified electrician.
3. Cover or shied any adjacent live components.
4. For indoor use only.

FUNCTION

1. Can identify day and night: The consumer can adjust working state in different ambient light. It can work in the daytime and at night when it is adjusted on the "sun" position (max). It can work in the ambient light less than 3LUX when it is adjusted on the "3" position (min). As for the adjustment pattern, please refer to the testing pattern.
2. Time-Delay is added continually: When it receives the second induction signals within the first induction, it will restart to time from the moment.

Diagram of a showerhead emitting red light rays, with no text or symbols present.

Good Sensitivity Poor Sensitivity

Diagram of a spray gun emitting red light rays, with an arrow indicating direction (no text or symbols)

INSTALLATION ADVICE

As the detector responds to changes in temperature, avoid the following situations:

• Avoid pointing the detector towards objects with highly reflective surfaces, like mirrors etc.
• Avoid mounting the detector near heat sources as heating vents, air conditioners, light etc.
• Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants etc.

Diagram of a room with two monitors and a ceiling-mounted device, showing light rays from the screen (no text or symbols)

Diagram showing a light bulb inside a 3D cube with diagonal lines, no text or symbols present

Diagram showing a potted plant under sunlight with a window and a roof, intersected by diagonal lines (no text or symbols)

INSTALLATION

• Switch off the power.
• Unload the transparent cover.
• Connect the power to connection terminal of sensor according to connection-wire diagram.
  • Install back the transparent cover into the original location.
• Fold the metal spring of the sensor upwards and then put the sensor into the suitable hole or installation box. Releasing the spring, the sensor will be set in this installation position.
  • After finishing installing, turn on the power and then test it.

WIRING DIAGRAM

SENSOR INFORMATION

Height of Installation: 1.8-4m DETECTION DISTANCE: Max. 8m

TEST

• Turn the TIME knob anti-clockwise on the minimum (IOS). Turn the LUX knob clockwise on the maximum (sun).
• Switch on the power; the sensor and its connected lamp will have no signal at the beginning. After Warm-up 30sec, the sensor can start work. If the sensor receives the

induction signal, the lamp will turn on. While there is no another induction signal any more, the load should stop working within 10 sec ± 3 sec and the lamp would turn off.

- Turn LUX knob anti-clockwise on the minimum (3). If the ambient light is more than 3LUX, the sensor would not work and the lamp stop working too. If the ambient light is less than 3LUX (darkness), the sensor would work. Under no induction signal condition, the sensor should stop working within 10sec±3sec.

Note: when testing in daylight, please turn LUX knob to ⚙ (SUN) position, Otherwise the sensor lamp will not work.

TROUBLESHOOTING

• The load does not work:

a. Please check if the connection of power source and load is correct.
b. Please check if the load is good.
c. Please check if the settings of working light correspond to ambient light.

• The sensitivity is poor:

a. Please check if there is any hindrance in front of the detector to affect it to receive the signals.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection field.
d. Please check if the installation height corresponds to the height required in the instruction.
e. Please check if the moving orientation is correct.

- The sensor can not shut off the load automatically:

a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is set to the maximum position.

RoHS