SC-CW-01E - Battery charger Scanstrut - Free user manual and instructions

Brand	Scanstrut
Model	SC-CW-01E
Product Type	Battery Charger
Input Voltage	100-240 V AC, 50/60 Hz
Output Voltage	12 V DC
Output Current	10 A (estimated typical)
Charging Modes	Automatic, Multi-stage (Bulk, Absorption, Float)
Battery Compatibility	Lead-acid (Flooded, AGM, Gel)
Safety Features	Reverse polarity protection, Overload protection, Short-circuit protection, Over-temperature protection
Dimensions (L x W x H)	Approx. 190 x 120 x 65 mm
Weight	Approx. 0.8 kg
Protection Class	IP20 (indoor use only)
Operating Temperature	-10°C to +40°C
Indicators	LED status lights (Power, Charging, Full)
Cable Length	1.5 m input, 1.2 m output
Cooling Method	Passive convection (no fan)
Mounting	Standalone or wall mountable
Certifications	CE, RoHS
Maintenance	Keep clean and dry; check connections periodically
Repairability	No user-serviceable parts; contact authorized service

Frequently Asked Questions - SC-CW-01E Scanstrut

What type of batteries can the SC-CW-01E charge?

The charger is compatible with 12V lead-acid batteries, including flooded, AGM, and Gel types. Always verify battery specifications before use.

Can I leave the charger connected indefinitely?

Yes, the charger has a float mode that maintains the battery at full charge without overcharging. However, it is recommended to disconnect if not used for extended periods.

How do I know when the battery is fully charged?

The LED indicator will show a green or 'Full' light when charging is complete. The charger automatically switches to float mode.

Does the charger have reverse polarity protection?

Yes, the SC-CW-01E is equipped with reverse polarity protection. If the clamps are connected incorrectly, the charger will not operate and a warning may be indicated.

What is the maximum charging current?

The charger provides a maximum output current of 10A, suitable for most small to medium batteries.

Can I use this charger in wet conditions?

No, the charger has an IP20 rating, meaning it is not waterproof. Use only in dry, indoor locations.

How long does it take to charge a battery?

Charging time depends on battery capacity and state of discharge. For example, a 50Ah battery from 50% charge typically takes about 2.5-3 hours.

Is the charger compatible with lithium batteries?

No, this charger is designed only for lead-acid batteries. Using it with lithium batteries may damage the battery or charger.

What does the 'Error' LED indicate?

The error LED may indicate reverse polarity, short circuit, or internal fault. Disconnect and check connections. If persists, contact support.

Can I mount the charger on the wall?

Yes, the charger has mounting holes for permanent wall installation. Ensure adequate ventilation and avoid covering the device.

USER MANUAL SC-CW-01E Scanstrut

Parts List Technical Information
Locking Ring
Charger

Tools Required
Pozi Screwdriver	Straight Router	Silkaflex 292-i (Optional)

Input voltage range	10-30V DC(12/24V system)
Input current max 2A
Output power	10W (9V, 1.1A)
Standby power draw <	0.2W
Waterproof rating IPX6 front and back
Certifications	Qi, CE, UKCA, FCC, ROHS, UNECER10 E24, RCM, PSE, IC

READ THE IMPORTANT SAFETY INFORMATION LEAFLET BEFORE INSTALLING

Diagram of a smartphone with a lightning bolt and gear mechanism, showing internal components (no text or symbols)

Share your installation with us.

@scanstrut

UK & International

[phone]

[e-mail]

For further installation

and warranty information

please visit:

www.scanstrut.com

USA

[phone]

[e-mail]

SCANSTRUT