MCH100SS - Range hood MATSUI - Free user manual and instructions

Product Type	Range Hood
Brand	Matsui
Model	MCH100SS
Width	100 cm
Depth	50 cm
Height (min-max)	62 - 110 cm
Weight	15 kg
Power Supply	220-240 V ~ 50 Hz
Motor Power	200 W
Extraction Rate (Max)	650 m³/h
Noise Level (Max)	65 dB(A)
Number of Speeds	3
Controls	Push buttons with LED indicators
Lighting	2 x 40 W halogen lamps
Filter Type	Aluminum grease filter, washable
Ducting	150 mm diameter, vertical or horizontal
Installation	Wall-mounted, fixed with screws (included)
Maintenance	Clean grease filter monthly in warm soapy water
Safety Features	Motor thermal cut-out, anti-return valve
Spare Parts Availability	Filters, lamps, motor available through authorized service
Energy Class	B

Frequently Asked Questions - MCH100SS MATSUI

How do I clean the grease filter?

Remove the filter by releasing the clips. Wash it in warm soapy water or in a dishwasher at low temperature. Dry thoroughly before reinstalling.

Can I use charcoal filters for recirculation?

Yes, optional charcoal filters (model CCF100) are available. Replace every 3-6 months for effective odor removal.

What is the recommended installation height?

For gas hobs, install at least 75 cm above the cooking surface; for electric hobs, at least 65 cm.

Why is my range hood noisy?

Check if the filter is clean and properly installed. A dirty or loose filter can cause rattling. Also ensure the ductwork is not blocked.

How do I replace the light bulbs?

Switch off power. Remove the bulb cover (turn or unclip). Replace with a 40W halogen bulb (G9 base). Do not touch the new bulb with bare hands.

What should I do if the motor stops running?

Check if the thermal cut-out has tripped due to overheating. Allow the motor to cool for 30 minutes, then reset by switching off and on. If problem persists, contact service.

Is ducting required?

The hood can be used in extraction mode (duct outside) or recirculation mode with charcoal filters. Ducting is recommended for best performance.

How often should I clean the filters?

Clean the grease filter every 1-2 months depending on usage. Replace charcoal filters every 3-6 months.

Can I install this hood myself?

Installation requires basic DIY skills and following the manual. Ensure proper electrical disconnection and secure mounting. If unsure, hire a professional.

What does the LED indicator mean?

The red LED flashes when the filter needs cleaning (after 40 hours of use). Reset by holding the speed button for 3 seconds.

USER MANUAL MCH100SS MATSUI

Line drawing of a kitchen range hood with chimney and base (no text or symbols)

Instruction Book

Cod:0103071745

Safety

• The appliance must be installed according to the manufacturer's instructions. Improper installation may result in injury or damage, for which the manufacturer cannot be held responsible.
• The electrical safety of this appliance is guaranteed only if it is connected to a properly earthed system which complies with the electrical safety standards in force. If you cannot verify that this fundamental safety requirement is in place, consult a qualified electrician. The manufacturer cannot be held responsible for an appliance which has not been correctly earthed.
• Check that the voltage (230 Volts AC) printed on the rating label inside the Cooker Hood corresponds to the mains voltage in your home. If in doubt call a qualified electrician.

• Never replace the power supply cable yourself. Damaged cables must only be replaced by an authorised service centre.

• Adaptors, multiple sockets and/or extension leads must not be used.
  • To avoid electrical shock, never touch the Cooker Hood or plug with wet hands.

• Ventilation outlets on the Cooker Hood should never be covered, as obstructions may cause overheating or fire.
  • Always disconnect the plug from the mains supply before cleaning the Cooker Hood or carrying out maintenance work.
• Do not flambé under the Cooker Hood as this may cause a fire hazard.
• Avoid leaving a gas hob on when there is no pan on the stove.
• There should be adequate ventilation of the room when the Cooker Hood is used at the same time as appliances burning gas or fuel.

WARNING!

It is hazardous for anyone other than authorised service personnel to carry out Servicing or repairs which involves the removal of covers.

To avoid the risk of an electric shock do not attempt to repair this appliance yourself.

Disposal

Old appliances still have some residual value. An environmentally friendly method of disposal will ensure that valuable raw materials can be recovered and used again. Up to date information concerning options for disposing of your old appliance and packaging from the new one can be obtained from your local council office.

Introducing Your New Cooker Hood

Before use

Please read these instructions carefully before using your new Matsui Cooker hood. The Cooker hood is for indoor, domestic use only. WARNING- Please be careful when unpacking and installing this appliance as sheet metal can cause injury if not handled with care.

Install Your New Cooker Hood

Installation and electrical wiring must be carried out by a qualified engineer to ensure all applicable codes and standards are followed. Before installing check that the voltage indicated on the rating plate is suitable for your home.

Location

The Cooker hood is designed to be a permanent fixture in the home, therefore needs to be located in a place that the lowest part of the hood will be set at least 70cm above the hob. The Cooker hood will need to be positioned with adequate ventilation directly over the cooker. The air that is discharged from the Cooker hood should NOT be filtered into a flue that is used for other appliances that use gas or other fuels. Regulations concerning the discharge of air MUST be fulfilled.

IMPORTANT: The Cooker hood flue MUST not be connected to a previously installed appliance i.e. water heaters, boilers or cooker. The Cooker hood MUST have a separate flue and MUST NOT be installed above a cooker with eye-level grills.

IMPORTANT: Easy access to the electrical socket must be maintained to ensure that you can carry out simple maintenance.

Before plugging in YOU MUST Check that you have a socket, which is compatible with the Cooker hood. If not see the section called ELECTRICAL CONNECTIONS on page 6.

Installation

Before beginning any installation work ensure the mains power has been turned off.

Extracted Air Installation

1 Using a Phillips screwdriver fix the ducting hose connector onto the air outlet of the hood

2 Connect the hose (not supplied) to the air duct. Use the adaptor provided to connect to a 125mm hose (not supplied). (refer to fig.1)

3 The ducting can pass through your wall to the outside.

4 If you operated the cooker hood in recirculation mode, fit the metal plate in the chimney to prevent the exhaust air from reaching the ceiling.(refer to fig.2)

Stencil

Use the stencil provided to help position the hood onto the wall directly below the ducting. NOTE: Take extreme care when drilling holes into your wall to avoid hidden electrical wiring.

1 With the stencil positioned on the wall, drill 4 holes onto the back wall. Push 4 raw plugs into the drill holes and partially screw in the top 2 screws.

2 Fix the hood onto the wall by positioning the upper 2 screws through the key holes on the back of the hood.

3 Attach the lower part of the hood by removing the filter panels to gain access to the lower safety screw holes.

Attaching the Chimney flue wall bracket

1 Using the wall bracket as a template, drill 2 holes into the wall and push raw plugs into the drill holes.
2 Place the wall bracket over the raw plugs and screw into position.

Technical line drawing of a mechanical assembly with no visible text or symbols

3 Screw the inner chimney flue section to the wall bracket.

Adjusting the telescopic hood

The telescopic chimney flue can be adjusted in height to fit your ceiling once fully attached to the wall.

Installation

Re-Circulation using Carbon filters

Two carbon filters (not supplied) can also be added to your Cooker Hood, when air is to be re-circulated instead of external ducting.

Attach to either side of the motor.

Please see the Partmaster Direct details on the back cover to order them.

(2 carbon filters required)

In Use

Control panel

0

1

2

3

0 = Switches the Cooker Hood off.

1 = Low speed. Is suitable when low levels of steam are created whilst cooking.
2 = Medium speed.
3 = High speed. Is suitable when high levels of steam are created whilst cooking.
☀ = Switches the overhead light on.

The Cooker Hood should be left on for at least 15 minutes after cooking has finished to ensure efficient filtering of the air.

Cleaning

Regular cleaning will help to maintain the effectiveness of your Cooker Hood.

1 Switch off and unplug the Cooker Hood before cleaning.
2 Clean the inside and outside of the Cooker Hood with a damp cloth and a mild detergent.

NOTE: Do not use solvents or abrasives as this may damage the Cooker Hood.

Warning: Your Cooker Hood can become a fire risk if it is not cleaned correctly

Cleaning the filters

To ensure the filters do not become a fire hazard we recommend they are washed every 3 months. Do not check the filter panels whilst the Cooker Hood is in use.

1 Before cleaning the filters always switch off and disconnect the electrical supply.
2 Remove the filter panels by holding down the buttons on each panel and lifting towards you. They can then be taken out of the cooker hood.

3 Wash each filter in warm water and a mild detergent, leave to soak and drain. Ensure it is completely dry before replacing into the Cooker Hood.
4 Place the bottom of each panel into the back of the Cooker Hood and raise the top to click into position.

NOTE: The filter panels are also dishwasher proof. The filter panels may alter in colour slightly after several washes, this is not a fault.

Maintenance and Troubleshooting

Changing the internal light

Allow the Cooker Hood to cool for at least 30 minutes after use before changing the light bulb.

1 Before carrying out the bulb replacement always switch off and disconnect the electrical supply.
2 To remove filters hold down buttons on each panel and lift towards you.
3 Remove the lamp rim by unscrewing the two screws.

Technical line drawing of a mechanical assembly with mounting holes and internal components (no text or symbols)

Warning: Hold the bulb as it will drop downwards as it's released.

4 Uncap the bulb and replace with a new one.
5 Screw the fixed lamp rim tightly in a clockwise direction.

6 Replace the filters.

The Cooker Hood is not working

• Check it is plugged in and switched on.
• Check that the fuse in the plug has not blown.
• Plug in another appliance, such as a lamp, to see if the socket is working.

Servicing

Only an authorised, qualified technician should perform repairs and maintenance of the appliance.

Technical specifications

Electrical information

Model MCH100SS

MCH100BLK

Rated Voltage 220-240

(V)

Rated Frequency 50

(Hz)

Rated Power 140

(W)

Weight 14

(kg)

Product Dimension

h/w/d 28x100x50

(cm)

Bulbs 2x20W max

Weight and Dimensions are approximate. Because we continually strive to improve our products we may change specifications and designs without prior notice.

THIS APPLIANCE MUST BE EARTHED.

This appliance is fitted with a fused three pin plug to BS 1363 which will be suitable for use in all houses fitted with sockets to current specifications.

If the fitted plug is not suitable for your socket outlets, it should be cut off and carefully disposed of. To avoid a possible shock hazard, do not insert the discarded plug into a socket.

Fitting a new plug

If for any reason you need to fit a new plug, the flexible mains lead must be connected as shown here. The wires in the mains lead fitted to this appliance are coloured in accordance with the following code

CONNECT GREEN AND YELLOW TO EARTH (E)

CONNECT

BLUE TO

NEUTRAL [N]

CONNECT

BROWN TO

LIVE (L)

13 AMP FUSE

MAKE SURE THE OUTER

SHEATH OF THE MAINS

LEAD IS SECURELY HELD

BY THE CLAMP

CE

If the colours of the wires in the mains lead of this appliance do not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured Green and Yellow MUST be connected to the terminal which is marked with the letter E (Earth) or symbol 12 or coloured Green. The wire which is coloured Blue MUST be connected to the terminal which is marked with the letter N or coloured Black. The wire which is coloured Brown MUST be connected to the terminal which is marked with the letter L or coloured Red.

Before refitting the plug cover, check that there are no cut or stray strands of wire inside the plug. Use a 13 Amp BS1362 fuse, only BSI or ASTA approved fuses should be used. If you are in any way unsure which plug or fuse to use, always refer to a qualified electrician.

Note: After replacing or changing a fuse on a moulded plug which has a fuse cover, the cover must be refitted to the plug, the appliance must not be used without a fuse cover. If lost, replacement fuse covers can be obtained from an electrical shop.

This appliance complies with the following EEC Directives:

73 / 23 EEC (Low Voltage Directive)

89 / 336 EEC (EMC Directive).

Partmaster co.uk

Visit Partmaster.co.uk today for the easiest way to buy electrical spares and accessories.

With over 1 million spares and accessories available we can deliver direct to your door the very next day.

Visit www.partmaster.co.uk

or call

0870 6001 338

(UK customers only)

Calls charged at National Rate.

This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU.

For more information, please contact the local authority or your retailer where you purchased the product.