DL-ILFO-H2 - Audio/video converter Digitalinx - Free user manual and instructions

Product Type	HDMI 2.0 Fiber Optic Extender Set (Transmitter + Receiver)
Dimensions (W x H x D)	26 mm x 15 mm x 72 mm (1 in x 0.6 in x 2.8 in) per unit
Weight	175 g (0.4 lbs) per unit
Power Supply Input	AC 100-240V, 50/60 Hz
Power Supply Output	DC +5V, 1A
Power Consumption	5 watts
Maximum Distance	200 m (660 ft) over duplex OM3 fiber
Required Fiber Cable	Duplex LC-LC OM3 (not single mode)
Bandwidth	18 Gbps
Video Compliance	HDMI 2.0b, HDCP 2.2, CEC
Supported Resolutions	Up to 4096x2160 @ 60Hz, 4:4:4, 8-bit
HDR Support	HDR10, HDR10+, Dolby Vision
Audio Support	LPCM, Dolby Digital/Plus/EX, Dolby TrueHD, DTS, DTS-EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD
Operating Temperature	0 to +50°C (32 to +122°F)
Storage Temperature	-30 to +70°C (-22 to +158°F)
Operating Humidity	10% to 85%, non-condensing
Included Items	1 Transmitter, 1 Receiver, 2 Power Supplies (with US, AU, EU, UK adapters), 2 Micro USB to USB cables, Installation Guide
Warranty	5 years
Care and Cleaning	Clean fiber optic connectors with lint-free cloth. Keep away from dust and moisture.
Safety	Use only supplied power adapters. Do not expose to water or excessive heat. Ensure proper ventilation.

Frequently Asked Questions - DL-ILFO-H2 Digitalinx

What is the maximum transmission distance of the DL-ILFO-H2?

The DL-ILFO-H2 can extend HDMI signals up to 200 meters (660 feet) using duplex OM3 fiber cable.

Does the DL-ILFO-H2 support 4K resolution?

Yes, it supports resolutions up to 4096x2160 @ 60Hz with 4:4:4 chroma subsampling and 8-bit color.

What type of fiber cable is required?

It requires duplex LC-LC OM3 fiber cable. Single mode fiber is not supported.

Can I power the receiver from the TV's USB port?

You can, but it is recommended to use the provided power supplies. The receiver requires a stable 5V/1A power source. If the TV's USB port cannot provide sufficient power, use the included adapter.

Does this extender support HDR and Dolby Vision?

Yes, it supports HDR10, HDR10+, and Dolby Vision.

What audio formats are supported?

It supports LPCM, Dolby Digital/Plus/EX, Dolby TrueHD, DTS, DTS-EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, and DSD.

Is the transmitter compatible with other receivers?

No, the DL-ILFO-H2 is sold as a set and the transmitter and receiver are only compatible with each other unless specifically noted otherwise.

What is included in the package?

The package includes: 1 Transmitter, 1 Receiver, 2 Power Supplies (with US, AU, EU, UK adapters), 2 Micro USB to USB cables, and an Installation Guide.

What is the warranty period?

The DL-ILFO-H2 comes with a 5-year standard warranty.

Can I use cable pass-throughs or keystone plates in the fiber run?

Digitalinx does not recommend using cable interrupts or pass-throughs as they may cause performance issues. Keep the fiber cable uninterrupted for best results.

USER MANUAL DL-ILFO-H2 Digitalinx

Two black USB devices with visible internal components, one labeled 'DL-ILFO-H2' and the other 'Digital INX', both connected to a port and connector port (no readable text beyond branding)

Product Overview

The DigitaLinx DL-ILFO-H2 HDMI 2.0 extender set extends uncompressed HDMI audio and video up to 200m / 660' using a duplex multi-mode OM3 fiber cable. The DL-ILFO-H2 Supports HDMI 2.0b up to 18Gbps, CEC, HDR10, HDR10+ Dolby Vision and HDCP 2.2 as well as High Definition Dolby and DTS audio formats.

The DL-ILFO-H2 is sold only as a set. The individual transmitter and receiver are not compatible with other fiber extender offerings unless specifically noted otherwise.

Package Contents

• (1) Transmitter (Tx) and One (1) Receiver (Rx)
• (2) Micro USB to USB power cables
• (1) Installation Guide
• (2) 5V 1A power supply with US, AU, EU and UK adapters

Installation Instructions

Connect Fiber Cables to Extenders

Connect a duplex LC OM3 optical fiber cable between the transmitter and the receiver, note that each fiber channel should be connected as (A) to (A) and (B) to (B) respectively.

The maximum length for the OM3 fiber cable is 200m / 660'. This extender will not work with single mode fiber cable for longer distances.

NOTE: Digitalinx does not recommend or support cable interrupts or pass-throughs in the fiber cable such as keystone plates or patch panels, this may cause undesired interruptions in system performance.

Connect Power

Connect the DL-ILFO-H2 transmitter and receivers USB port to the supplied power supplies and connect to a local power source. The DL-ILFO-H2 transmitter can be powered by 5V from pin #18 of the HDMI interface however the receiver must receive a constant power supply @ 5V/1A, some TV's and projectors may be able to supply this power via a USB A port but if the power supplied by the TV is not stable or sufficient enough, it is recommended to use the provided power supplies on each extender device. Always the check the available USB power on a TV to be sure the receiver will receive the correct amount of voltage and amperage if using this method.

NOTE: Digitalinx recommends using both USB power supplies connected to both transmitter and receiver for a stable power connection and supply.

When power is supplied the power LED will turn ON.

Connect Fiber Extender to Devices

Connect the DL-ILFO-H2 transmitter to the HDMI source, connect the receiver to the TV display.

NOTE: Be sure the extender device labeled TRANSMITTER is connected to the HDMI source, and the device labeled RECEIVER is connected to the TV display.

When a successful audio and video link has been established between the HDMI source / transmitter and TV display / receiver the STATUS light on the extender devices will blink.

graph TD
    A["HDMI SOURCE"] --> B["DL-ILFO-H2 TRANSMITTER"]
    B --> C["USB Power"]
    C --> D["OM3 Fiber up to 200m / 660'"]
    D --> E["USB Power"]
    E --> F["DL-ILFO-H2 RECEIVER"]
    F --> G["DISPLAY"]

Technical Specifications

Supported Audio and Video
Video Compliance HDMI 2.0b, HDCP 2.2, and CEC (Consumer Electronics Control)
Input / Output Resolution Support All resolutions are supported up to 4096x2160 / 60Hz; 4:4:4; 8 bit deep color
Maximum Pixel Clock 600MHz
Embedded Audio LPCM, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-EX, DTS-96/24, DTS High Res, DTS-HD Master Audio, DSD
Fiber Optic Signal Characteristics
Maximum Distance 200 meters / 660' feet
Required Cable Type Duplex LC-LC OM3
Bandwidth 18Gbps
Chassis and Environmental
Dimensions (W*H*D) 26 mm (1 in) x 15 mm (0.6 in) x 72 mm (2.8 in)
Operating Temperature (Environment) 0 to +50°C (32 to +122 °F)
Operating Temperature (Storage) -30 to +70°C (-22 to +158 °F)
Operating Humidity (Environment) 10% to 85%, Non-condensing
Product Weight 175g / .4 lbs
Power
Maximum Power Consumption	5 watts
Power Supply Input Voltage	AC 100-240V, 50/60Hz.
Power Supply Output Voltage	DC +5 V, 1A
Regulatory	CE, FCC, RoHS
Other
Standard Warranty	5 Years
Included Items	(1) Transmitter, (1) Receiver, (1) Install Guide, (2) DC 5V Power Supply with US, UK, EU and AU power adapters (2) USB Micro to A power cables

Thank you for your purchase.

For Technical Support please call our toll free number at 800-530-8998 or email us at [e-mail]

www.libav.com

Digitalinx is a brand of:

LIBERTY

AV SOLUTIONS

11675 Ridgeline Drive

Colorado Springs, Colorado

80921 USA

Phone: [phone]

Fax: [phone]

Toll-Free: 800-530-8998