P406U - Power strip CyberPower - Free user manual and instructions

Product Type	Surge Protector Power Strip
Model Number	P406U
Outlets	4 Standard Grounded Outlets
USB Charging Ports	2 USB-A Ports (Shared 2.4 A)
Surge Protection Rating	500 Joules
Circuit Breaker	Resettable 15 Amp
Electrical Rating	125 V / 15 A / 60 Hz / 1875 W
Power Cord Length	6 ft (1.8 m) Braided Cord
Switch Control	ON/OFF Reset Control Switch with Circuit Breaker
Indoor Use Only	Yes
Daisy Chain Prohibited	Do not plug into another relocatable power tap or daisy chain surge protectors
Aquarium Equipment	Not for use with aquarium equipment
Medical/Life Support	Not for medical or life support equipment
Safety Compliance	FCC Part 15 Class B
California Prop 65 Warning	Contains Styrene and Bisphenol A (BPA)
Protection Disconnection	Internal protection disconnects surge component at end of life; maintains unprotected power
Technical Support	1-877-297-6937, Mon-Fri 7am-6pm CST
Warranty Information	Visit CyberPowerSystems.com
Manual Download	Free PDF available at notice-facile.com

Frequently Asked Questions - P406U CyberPower

How do I reset the surge protector after an overload?

Switch the ON/OFF control to OFF. Then remove the device causing the overload. Finally, turn the switch back to RESET. The circuit breaker will reset automatically when the overload is cleared.

Can I plug multiple surge protectors together?

No, do not daisy chain surge protectors or plug this unit into another relocatable power tap. This can cause overloading and fire hazard.

Can I use this surge protector outdoors?

No, use only in dry locations and indoors. Exposure to moisture increases risk of electric shock.

What is the surge protection rating?

The surge protection rating is 500 Joules. This absorbs voltage spikes to protect connected equipment.

How many USB devices can I charge simultaneously?

You can charge up to two USB-A devices simultaneously. The total output is 2.4 A shared, so charging speed may decrease if both ports are used.

What is the maximum power draw?

The maximum power draw is 1875 W at 125 V and 15 A. Exceeding this will trip the circuit breaker.

Is this surge protector suitable for medical equipment?

No, do not use for medical or life support equipment. The unit may provide unprotected power after surge protection fails.

How do I know if the surge protection is still working?

The unit does not have an indicator light. However, if the device stops providing protection, it will still pass power but without surge suppression. Refer to the manual for more details.

What is the warranty coverage?

Warranty details are available at CyberPowerSystems.com. It covers defects and connected equipment under specified conditions.

Where can I find technical support?

Contact technical support toll-free at 1-877-297-6937, Monday-Friday 7:00am-6:00pm CST, or visit CyberPowerSystems.com/support.

USER MANUAL P406U CyberPower

Cyber Power Systems (USA), Inc.

4241 12th Avenue East, Suite 400 | Shakopee, MN 55379

CyberPowerSystems.com

FEATURES

1. ON/OFF Reset Control Switch and Circuit Breaker

Controls power to all outlets. The switch is also a 15 A breaker. When an overload occurs, it will automatically switch off. To resume operation, ensure the overload condition is removed and reset the surge protector by switching the unit ON.

2. Standard Grounded Outlets (4)

3. USB-A Charging Ports (2)

4. Braided Power Cord

SPECIFICATIONS

Model Number: P406U

Outlets: Standard Grounded Outlets (4).

USB Charging Ports (2)

Power Cord Length: 6 ft

Surge Protection: 500 Joules

USB-A Charging Output: 2.4 A Shared

Electrical Rating: 125 V/15 A/60 Hz/1875 W

Circuit Breaker: Resettable 15 Amp

i WARNING: This product can expose you to chemicals including Styrene, which are known to the State of California to cause cancer, and Bisphenol A (BPA), which are known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P6SWarnings.ca.gov.

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK:

Use only in dry locations and only indoors.

DO NOT plug into another relocatable power tap.

DO NOT "daisy chain" surge protectors.

DO NOT use with any aquarium equipment

DO NOT use if properly grounded outlets are not available.

DO NOT install this device if there is less than 10 meters (30 feet) or more of wire

between the electrical outlet and electrical service panel.

DO NOT use for medical or life support equipment. This device features an internal protection that will disconnect the surge protective component at the end of its useful life, but it will maintain unprotected power to the load.

TROUBLESHOOTING

If the ON/OFF is switched OFF, the 15 Amp circuit breaker may have tripped. Examine your connected equipment and remove the device that is overloading the circuit. Then, turn the ON/OFF switch back to RESET.

FOR MORE INFORMATION

Visit CyberPowerSystems.com for more information regarding:

• Product information and certifications

- Product warranty

• Connected equipment guarantee

TECHNICAL SUPPORT

Visit: CyberPowerSystems.com/support

Toll-Free: 1-877-297-6937

Hours of Operation: Monday - Friday: 7:00am - 6:00pm CST

© 2021 Cyber Power Systems (USA), Inc. All rights reserved.

All other trademarks are the property of their respective owners.

CONFORMANCE APPROVALS This device complies with Part

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired cessation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates taxes, and can radiate radio frequency energy and, if not related and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver. - General the equipment into an pellet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

11.6.2019(2): Expenses as modifications and expressivity granted by the

The internal target of investment is not explicitly approved by the party responsible for compliance could void the user's authority to operate the equipment.

KOI-0000926-00