MGDR-200 - Home Automation Nexa - Free user manual and instructions

Product Type	Wireless Remote Control
Brand	Nexa
Model	MGDR-200
Category	Home Automation
Dimensions	60 x 60 x 20 mm
Weight	50 g
Power Supply	1 x CR2032 battery (included)
Wireless Protocol	RF 433 MHz
Operating Range	Up to 30 m indoors
Functions	Turn on/off lighting and appliances, dimming control (compatible)
Number of Channels	1 channel
Suitable for	Nexa receivers, plugs, dimmers
Mounting	Handheld or wall-mounted (bracket included)
Maintenance & Cleaning	Wipe with a dry, soft cloth; do not use liquids
Safety	Keep away from water and high temperatures; avoid dropping
Spare Parts & Repairability	Battery replaceable; no user-serviceable parts inside
Included Accessories	Battery, mounting bracket, user manual
Compliance	CE, RoHS
Warranty	2 years

Frequently Asked Questions - MGDR-200 Nexa

How do I pair the MGDR-200 with a Nexa receiver?

Press and hold the learning button on your Nexa receiver until the LED flashes. Then press the button on your MGDR-200 remote. The LED will stop flashing to confirm pairing. Repeat for other receivers.

What battery does the MGDR-200 use and how do I replace it?

The remote uses a CR2032 lithium coin cell battery. To replace, slide open the battery compartment on the back, remove the old battery, insert a new one with the positive (+) side facing up, and close the compartment.

What is the operating range of the MGDR-200?

The operating range is up to 30 meters indoors, depending on walls and obstructions. For best performance, avoid metal barriers.

Can I use the MGDR-200 to control lights and other appliances?

Yes, when paired with compatible Nexa receivers such as the KF-10 plug or in-wall switches, you can turn on/off lighting and appliances. Some receivers also support dimming if the remote is configured accordingly.

How many MGDR-200 remotes can I use with one receiver?

Nexa receivers typically support pairing with multiple remotes (up to 8). Follow the pairing procedure for each remote.

Does the MGDR-200 require a line of sight?

No, it uses RF (radio frequency) at 433 MHz, so it can work through walls and furniture, though range may be reduced.

How do I reset the MGDR-200 to factory settings?

The remote does not have a factory reset function. To unpair, simply delete the remote from the receiver’s memory (refer to receiver manual) or replace the battery.

Is the MGDR-200 weatherproof? Can I use it outdoors?

No, the MGDR-200 is designed for indoor use only. Keep it away from moisture and extreme temperatures.

My MGDR-200 seems unresponsive. What should I do?

First, check the battery: if the LED is dim or absent, replace the battery. Ensure you are within range of the receiver. Re-pair the remote if needed.

Where can I find the user manual for the MGDR-200?

The user manual is available for free download on notice-facile.com in PDF format. You can also request a translated version via email on the same site.

USER MANUAL MGDR-200 Nexa

Close-up of a black plastic electrical plug with a handle and terminal socket (no visible text or symbols)

NEXA

MGDR-200

DENNA PRODUKT HAR STÖD FÖR SMART MODE.

Close-up of a black plastic electrical plug with a metal pin, no visible text or symbols

NEXA

MGDR-200

Plug-in Dimmer for outdoor use

TECHNICAL DATA
MGDR-200

Power supply 220-240 V~50 Hz
Max. load 200 W
Max. load LED 3-24 W LED
Protocol System Nexa (433,92 MHz)
Range up to 30 m
Memory slots 32
Own consumption < 1 W
IP classification IP44
Dimensions 53 x 70mm

A declaration of conformity is available online at www.nexa.se

NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN

[e-mail] | www.nexa.se

THIS PRODUCT FEATURES SUPPORT FOR SMART MODE.

In units that support Smart Mode, up to 3 different favourite scenarios can be saved and then activated easily using a Nexa Smart Mode transmitter.

Plug-in receiver with dimmer function for earthed sockets. Works with System Nexa remote controls, transmitters and Nexa Bridge. The system is “self-learning”, which ensures extremely simple and flexible installation.

INSTALLATION

Connect power to the receiver; make sure that the output does not exceed the output stated in the table under "Technical Data".

PROGRAMMING

1. Connect the receiver (plug-in) to an electrical socket. The receiver will switch to programming mode as soon as current is applied.
2. Press the "ON" button for the chosen channel on any System Nexa remote control within 6 seconds.

CONFIRMATION OF PROGRAMMING

The connected light will dim up and down two times.

DELETE MEMORY

1. To delete a memory slot, remove the receiver (plug-in) from the wall socket.
2. Wait for at least 6 seconds.
3. Replace the receiver in a wall socket.
4. Press the "OFF" button for the selected channel on a System Nexa remote control within 6 seconds.

To delete all memory slots, repeat steps 1–3 above and then press the "ALL OFF" button on the System Nexa remote control within 6 seconds.

CONFIRMATION OF DELETION

The connected light will dim up and down two times.

MEMORY

Each MGDR-200 plug-in receiver has 32 memory slots. When all 32 slots are full, slot 1 will be overwritten on new programming.

CONTROL

The plug-in receive can be controlled in several ways.
1. With a System Nexa Remote Control
2. With other programmed System Nexa transmitters
3. With Nexa Smart Hub
4. With Nexa Bridge

DIMMER SETTINGS

The MGDR-200 is supplied set up for trailing edge phase dimming.

SETTING THE LOWEST DIMMER LEVEL

1. Remove the (plug-in) receiver from the wall socket.
2. Wait for at least 6 seconds.
3. Replace the receiver in a wall socket.
4. Press the ON button on a programmed System Nexa remote control for 3 seconds within 6 seconds.
5. The connected light will dim up and down two times.
6. Use the programmed remote control to adjust the lowest dimmer level. ON increases the level one step, OFF reduces the level one step. (Four steps in all)
7. Press the ON button on a programmed System Nexa remote control for 3 seconds to confirm the lowest dimmer level.
8. The connected light will dim up and down two times, and then dim down to the lowest level set to confirm the new setting.

SAFETY AND INFORMATION

Range indoors: up to 30 m (optimal conditions). The range is heavily dependent on local conditions – such as if there are any metals nearby. For example, the heavy metal coating in low-emission energy glass has a negative impact on the range of the radio signals. There may be limitations on the use of the unit outside the EU. If appropriate, check that the unit complies with the local regulations.

Max. load: Never connect lights or equipment that exceeds the maximum load of the receiver. This can result in faults, short circuit or fire.

Life-support equipment : Never use Nexa products for life support equipment or other devices where faults or disruptions can have life-threatening consequences.

Disruptions: All wireless units can be affected by disruptions that may have an impact on performance and range. The minimum

distance between two receivers should therefore be at least 50 cm. Repairs: Do not attempt to repair the product. It does not contain any serviceable parts.

Waterproofing: The product is in a flush-proof design (IP44). For proper outdoor function, the connected plug must be of an approved design for outdoor use (IP44).

Cleaning: Clean the product with a dry cloth. Do not use chemicals, solvents or potent cleaning agents.

Environment: Do not expose the product to extreme heat or cold, as this may damage the electronic circuits or shorten their service life.

NORSK

Close-up of a black plastic electrical plug with a handle and terminal pin (no visible text or symbols)

NEXA

MGDR-200

DETTE PRODUKTET HAR ST∅TTE FOR SMART MODE.

MGDR-200 leveres innstilt for bakkantstyrt fasedimming.

INNSTILLING AV LAVESTE DIMMERNIVÅ

1. Ta mottakeren (pluggen) ut av stikkontakten.
2. Vent i minst 6 sekunder.
3. Sett mottakeren i en stikkontakt igjen.
4. Trykk på «PÅ»-knappen på en registrert System Nexa-fjemkontroll innen 6 sekunder og hold den inne i 3 sekunder.
5. Tilkoblet lampe dimmes opp og ned to ganger.
6. Bruk den registrerte fjernkontrollen til å justere laveste dimmemivå. «PÅ» hever nivået med ett trinn, mens «AV» reduserer nivået med ett trinn. (Det er 4 trinn.)
7. Trykk på «PÅ»-knappen på en registrert System Nexafjemkontroll og hold den inne i 3 sekunder for å bekrefte laveste dimmernivå.
8. Tilkoblet lampe dimmes opp og ned to ganger og dimmes deretter til innstilt laveste nivå for å bekrefte den nye innstillingen.

SIKKERHET OG ANNEN INFORMASJON

Close-up of a black plastic electrical plug with a metal pin and handle (no visible text or symbols)

NEXA

MGDR-200

TEKNISET TIEDOT
MGDR-200