EWYD580BZSS - Water pump DAIKIN - Free user manual and instructions
Find the device manual for free EWYD580BZSS DAIKIN in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Water Pump |
| Brand | Daikin |
| Model | EWYD580BZSS |
| Pump Type | Centrifugal |
| Rated Power | 5.8 kW |
| Max Flow Rate | 580 L/min |
| Max Head | 50 m |
| Inlet Diameter | 80 mm |
| Outlet Diameter | 80 mm |
| Voltage | 400V 3Ph |
| Frequency | 50/60 Hz |
| Protection Class | IP55 |
| Insulation Class | F |
| Weight | 120 kg |
| Dimensions (LxWxH) | 800 x 600 x 700 mm |
| Noise Level | 75 dB(A) |
| Max Operating Pressure | 10 bar |
| Fluid Temperature | -10°C to +60°C |
| Ambient Temperature | -20°C to +40°C |
| Material | Cast Iron |
| Shaft Seal | Mechanical |
| Bearings | Sealed |
| Electrical Connection | Terminal Box |
| Certifications | CE, ISO 9001 |
| Maintenance | Regularly inspect seals and bearings; clean strainer monthly |
| Safety | Disconnect power before servicing; use lockout/tagout |
Frequently Asked Questions - EWYD580BZSS DAIKIN
How do I install the Daikin EWYD580BZSS water pump?
Ensure a solid foundation, align the pump with piping, use flexible connectors to reduce vibration, and wire the motor according to the terminal box diagram. Prime the pump before startup.
What type of fluid can be used with this pump?
Clean water or non-aggressive liquids compatible with cast iron and mechanical seal. Maximum fluid temperature is 60°C. Avoid abrasive or corrosive fluids.
How do I prime the pump?
Fill the suction line and pump casing completely with liquid to remove air. Open the vent plug on the pump housing until liquid flows out steadily, then close it. Never run the pump dry.
What should I do if the pump is noisy?
Check for cavitation (insufficient suction pressure), misalignment, or worn bearings. Ensure the pump is securely mounted and piping is properly supported. Air in the system can also cause noise.
How often should I perform maintenance?
Monthly: check for leaks, noise, and vibration. Quarterly: inspect strainer and clean if needed. Annually: replace mechanical seal and lubricate bearings if required. Refer to the manual for detailed intervals.
What is the correct rotation direction?
Looking at the motor fan end, the shaft should rotate clockwise. Verify by momentarily energizing the motor; if incorrect, swap any two phase wires on three-phase models.
Can I use a variable frequency drive (VFD) with this pump?
Yes, but ensure the VFD is rated for the motor power and does not cause overheating at low speeds. Minimum frequency typically 25-30 Hz to maintain cooling. Consult Daikin for specific settings.
What are the electrical requirements?
The pump requires a 400V 3-phase supply at 50/60 Hz. Use a suitable circuit breaker and cable sized per local code. Include thermal overload protection.
How do I replace the mechanical seal?
Disconnect power, isolate the pump, drain fluid, remove the motor and coupling, then access the seal. Note the orientation of the rotating and stationary faces. Use genuine Daikin seal kit for replacement.
Where can I find spare parts?
Contact an authorized Daikin distributor or service center. Provide the model EWYD580BZSS for accurate parts. Common spares include mechanical seal, bearings, and impeller.
User questions about EWYD580BZSS DAIKIN
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Water pump in PDF format for free! Find your manual EWYD580BZSS - DAIKIN and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. EWYD580BZSS by DAIKIN.
