CT 12105 - Fan Orbegozo - Free user manual and instructions

Product Type	Ceiling fan with light
Brand	Orbegozo
Model	CT 12105
Use	Domestic
Power supply	220-240 V ~ 50 Hz
Number of speeds	3 (fast, medium, slow)
Rotation direction switch	Yes (push button)
Lighting type	Integrated (light kit)
Bulb type	E27
Number of bulbs	3
Maximum wattage per bulb	60 W
Minimum installation height	2.30 m
Control method	Pull chain switches
Installation	Ceiling, mounting bracket
Maintenance	Clean with a soft dry cloth
Safety	Stop before reversing direction, grounding required
Certifications	CE (Directives 2006/95/EC and 2004/108/EC)
Mounting point capacity	Minimum 50 kg

Frequently Asked Questions - CT 12105 Orbegozo

How to install the ceiling fan?

Follow the 12 installation steps detailed in the manual. Ensure the mounting point supports at least 50 kg and the blade is more than 2.30 m from the floor. Connect the cables respecting the grounding.

How to select the fan speed?

Pull the fan's pull chain switch. The sequence is: first position = fast speed, second = medium speed, third = slow speed, fourth = off (OFF).

How to reverse the blade rotation direction?

First turn off the fan (OFF position). Press the direction control switch located on the housing. Leave it in the up or down position according to the desired direction.

How to turn the light on/off?

Pull the light pull chain switch to turn the lights on or off.

What type of bulb to use?

Use bulbs of type E27 with a maximum power of 60 W each. The fan accepts 3 bulbs (sold separately).

How to clean the fan?

Clean with a soft dry cloth. Never use scouring pads, abrasives, or chemical cleaners. Avoid condensation coming into contact with electrical components.

What to do if the fan does not work?

Check that the power is connected and the circuit breaker has not tripped. Ensure electrical connections are correct and the fan is properly grounded. If the problem persists, contact an authorized technical service.

The fan is noisy. What to do?

Check that all mounting screws of the blades and bracket are properly tightened. Ensure the blades are balanced and no object obstructs their rotation. The installation must be stable to avoid vibrations.

Can I use a speed controller?

It is not recommended to use a speed controller with this fan unless otherwise indicated. The model is designed to be used with the supplied pull chain switches. Using a controller could damage the motor.

Does the fan need to be grounded?

Yes, this appliance must be grounded in accordance with electrical standards. If no ground wire is available, ask a qualified electrician for advice.

USER MANUAL CT 12105 Orbegozo

Sonifer, S.A.

Read this manual carefully before running this appliance and save it for reference in order to obtain the best results and ensure safe use.

Dear Customer, If you follow the recommendations contained in this Instruction Manual, our appliance will give you constant high performance and will remain efficient for many years to come. Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing. If you give this device to other people, please also pass on the operating instructions.

General Safety Instructions

1. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children must never play with the appliance. Cleaning and user maintenance must never be carried out by children without supervision.
2. Children should be supervised to ensure that they do not play with the appliance.

3. Keep the appliance and the cable cord out of the reach of children less than 8 years old.

4. WARNING: In order to ensure your children's safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach.

5. If the supply cord is damaged it must be repaired by the Authorized Service Agent.
6. Never pull on the cord when unplugging.
7. Do not use the unit with a damaged cord or plug, or if it is not working properly.
8. Do not handle the appliance with wet hands.
9. Never immerse the appliance in water or any other liquid.
10. Make sure the appliance has been unplugged before cleaning.
11. This appliance must be installed following the national regulations for electrical installations.
12. This appliance is for household use only.
13. In case that you need a copy of the instruction manual, you can ask for it writing an email to [e-mail].
14. WARNING: In case of misuse, there is a risk of possible injury.

Other specific safeguards

1. The method of disconnection from the mains supply must incorporate a switch or isolator with a minimum contact separation of 3 mm. on all poles.

2. Make sure that when the fan is fitted in the chosen position, there is no possibility of the rotating blades coming into contact with any object. Blades should be at least 2.30 m from floor when fan is hung.

3. If you are installing more than one ceiling fan make sure that you do not mix fan blade sets, even though they are from the same ceiling fan model.

4. Before beginning, disconnect power by removing fuse or turning off circuit breaker.
5. Once fan installation is completed make sure that all connections are secure to prevent fan from falling.
6. Fan must be turned off and stopped before reversing fan direction.
7. Check that the means of fitting the fan to the ceiling is capable of supporting the weight of the fan when in operation. (Minimum 50Kg.).

INSTALLATION OF THE CEILING FAN

1- Open the box and take the fan out.	2- Mark the centre of the mounting bracket. Thread the lead wires through the mounting bracket holes, secure the mounting bracket to the ceiling joist using the flat washers, the lock washers, the set screws and the wall washers (sold separately).	3 - Hang the ball joint and the fan onto the bracket. Make sure the guied pin of bracket is fitted into slot of ball joint.
4- Connect the lead wires to the terminal block. Make sure that the connections are done properly and that no wires stand out of the connection blocks. This product must be earthed – if there is no earth cable available, contact an electrician.	5- Mount the upper canopy to the mounting plate, hang the fan on two of the screws and the washers through the key-shaped holes. Make sure that no part of the cable is caught during mounting.	6- Tighten all the screws, making sure that the canopy is placed properly and that no wires are caught. Ensure that the drawing-pin shaped guide of the upper canopy fits perfectly into the slot.
7- Attach the blade brackets to the fan blades, tightening the screws, the flat washers, the lock washers and the nuts.	8- Mount the fan blades to the motor, tightening all screws and lock washers.	9-Affix the light kit to the switch plate connecting the 2 plugs and then tighten the three screws and the star washers.
10-Unscrew the thumb screws from the lampshade support. Put the lampshades on their support and carefully screw back the thumb screws to fix the lampshade. Be careful not to overtighten the thumb screws, because the lampshades might break.	11-Put in the bulbs (sold separately).	12-Connect the pull chains to the light switch and the fan switch. Turn the electricity supply back on and switch on.

To switch the fan on/off and select the speedUse the fan pull switch to turn the fan on/off and select the speed.Sequence of the pull switch_from the OFF position.First position - High speed.Second position – Medium speed.Third position – Low speed.Fourth position – Off.

Control button for rotation direction of fan blades.Press this button to select either a clockwise or anti-clockwise blade rotation.Please note: Before using this button, switch the fan off (OFF position) to avoid any accidents.Keep the button in an “Up” or “Down” position.

Light switchUse the light pull switch to turn the lights on/off.

MAINTENANCE

HOW TO REPLACE A LIGHT BULB

1. Switch the device off (preferably, turn it off at the circuit breaker) and leave to cool. (Take care: light bulbs can get very hot when in use.)
2. Remove the bulb by holding it firmly and turning it anti-clockwise.
3. Take a new bulb and put it carefully into its holder. Screw it in clockwise.
4. Turn the power supply on again and switch on.

Important: The bulbs for this fan must be E27/60W(x3)

CLEANING

Clean with a soft, dry cloth. Never use scouring pads, abrasive or chemical cleaners. Do not allow condensation to come in contact with the electrical components.

Disposal of old electrical appliances.

The European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out "wheeled bin" symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance.

DECLARATION OF CONFORMITY:

This device complies with the requirements of the Low Voltage Directive 2006/95/EC and the requirements of the EMC directive 2004/108/EC.

CONSEILS DE SECURITE