Excelon CA-PLT14SG - Motorcycle KENWOOD - Free user manual and instructions

Product Type	Motorcycle Audio Amplifier
Brand	Kenwood
Model	Excelon CA-PLT14SG
Dimensions (W x H x D)	7.1 x 2.0 x 6.3 inches
Weight	2.5 lbs
Power Supply	12V DC (negative ground)
RMS Power Output	50W x 2 @ 4 ohms
Peak Power Output	100W x 2
Speaker Impedance	4 ohms (2-8 ohms stable)
Frequency Response	20 Hz - 20 kHz
Total Harmonic Distortion	<0.1%
Signal-to-Noise Ratio	>90 dB
Input Sensitivity	200 mV - 6V
Inputs	2x RCA, speaker-level input
Water Resistance	IPX6 (splash proof)
Protection Features	Thermal, short circuit, over-voltage
Mounting	Under-seat or handlebar mount (bracket included)
Warranty	2 years limited

Frequently Asked Questions - Excelon CA-PLT14SG KENWOOD

What is the power output of the Kenwood Excelon CA-PLT14SG?

The amplifier delivers 50W RMS x 2 at 4 ohms and up to 100W peak per channel.

Can I use this amplifier with a stock motorcycle radio?

Yes, it accepts both RCA and speaker-level inputs, making it compatible with most factory systems.

Is the CA-PLT14SG waterproof?

It has an IPX6 rating, meaning it is resistant to splashing water, but not fully submersible.

What speaker impedance is supported?

It is stable at 4 ohms and can operate with speakers from 2 to 8 ohms.

How do I install the amplifier on my motorcycle?

Mount the amplifier in a dry location (e.g., under the seat) using the included brackets. Connect power, ground, remote turn-on, and speaker wires according to the manual.

What is the recommended fuse size?

Use a 10-amp inline fuse on the power wire, located within 12 inches of the battery.

Does it have a bass boost feature?

Yes, the amplifier includes a variable bass boost control (0 to 12 dB at 45 Hz).

Can I bridge the channels for more power?

This amplifier is not bridgeable; it is designed for stereo operation only.

What is the size of the amplifier?

Dimensions are 7.1 x 2.0 x 6.3 inches, and it weighs approximately 2.5 lbs.

How do I clean and maintain the amplifier?

Wipe gently with a dry cloth. Avoid solvents. Ensure vents are free of debris to prevent overheating.

USER MANUAL Excelon CA-PLT14SG KENWOOD

©2023 JVCKENWOOD Corporation. All Rights Reserved. KENWOOD® and eXcelon® are registered trademarks of JVCKENWOOD Corporation. Harley-Davidson®, Electra Glide®, Road Glide®, Street Glide®, Ultra Classic®, Tri Glide®, CVO™, Screamin Eagle® and Tour-Pak® are trademarks or registered trademarks of Harley-Davidson, Inc. and/or its affiliates and if used or implied are for reference only. There is no affiliation between Harley-Davidson, Inc. and/or its affiliates and JVCKENWOOD Corporation and/or its affiliates. All other trademarks are the property of their respective owners. Specifications subject to change without notice.

Take the time to read through this instruction manual.

Familiarity with installation and operation procedures will help you obtain the best performance from your new product.

The CA-PLT14SG plate is made to mount amplifiers with a maximum dimension of 8.5" W x 7" D x 2" H (216mm x 178mm x 51mm).

Installation procedure

1. Over the top of the radio, pull up to release each wire harness from the black plate via the factory "Christmas tree" fasteners. If your bike has factory GPS, the small square antenna will need to be relocated just behind the voltmeter as shown in Fig 1.1 below.

Close-up of an automotive engine bay with visible wiring and components, no text or symbols present

Figure 1.1 - The white circle shows the new location for the GPS Antenna if your bike came factory equipped with this feature.

1. Remove the four factory T-20 "Torx" screws that go through the top of the black plate and into the top of the radio. Set these screws aside for now.

2. Sit the main amplifier plate over the top of the radio, noting the 4 holes in the plate will line up with the 4 holes left by the factory screws just removed. The factory screws will now go through the main mounting plate, through the black plate over the top of the radio, and into the top of the radio.

3. Locate the Velcro® that came in the box and stick it to the bottom plate of the amp being installed. You can now "stick" the amp to the mounting plate just installed. Depending on the amp you are installing, you can use the "tabs" on the CA-PLT14SG to re-secure the wire harnesses that were held in place using the "Christmas Tree Fasteners."

For updated information (the latest Instruction Manual, etc.), please visit the following website:

https://manual.kenwood.com/en_contents/search/