R2S - Dishwasher REX - Free user manual and instructions

Product Type	Freestanding Dishwasher
Brand	Rex
Model	R2S
Dimensions (H x W x D)	85 x 60 x 60 cm
Weight	45 kg
Power Supply	220-240 V, 50 Hz, 10 A
Energy Efficiency Class	E
Number of Place Settings	12
Wash Programs	Eco, Intensive, Normal, Quick, Rinse
Noise Level	49 dB(A)
Water Consumption per Cycle	9.5 L
Annual Energy Consumption	295 kWh/annum
Drying System	Condensation drying
Control Type	Electronic push buttons with LED display
Installation Type	Freestanding
Salt and Rinse Aid Indicator	Yes
Delay Start	Yes, up to 24 hours
Safety Features	Child lock, anti-flood system, overfill protection
Spare Parts Availability	Racks, filters, spray arms, detergent dispenser
Maintenance	Clean filters regularly, check spray arms, descale periodically

Frequently Asked Questions - R2S REX

How do I install the Rex R2S dishwasher?

Ensure the dishwasher is placed on a level surface. Connect the water inlet hose to a cold water supply (3/4 inch thread) and the drain hose to a suitable drain. Plug into a grounded outlet (220-240V). Adjust the feet to level the appliance.

What detergent should I use?

Use a dishwasher detergent (powder, gel, or tablets) specifically designed for automatic dishwashers. For best results, use a multi-function tablet with salt and rinse aid included. Adjust the dosage according to water hardness.

Why is my dishwasher not cleaning properly?

Check that the spray arms are not blocked and can rotate freely. Clean the filters and ensure the detergent dispenser is working. Use a rinse aid to improve drying. Also verify that the water inlet pressure is adequate (0.04-1.0 MPa).

How do I clean the filters?

Turn off the dishwasher and remove the lower rack. Unscrew the filter assembly (cylindrical and flat mesh) and rinse under running water. Use a soft brush if needed. Reassemble securely. Clean every 2-3 months.

What does the error code E1 mean?

Error code E1 usually indicates a water inlet problem. Check that the water tap is open and the inlet hose is not kinked or frozen. Also inspect the water inlet valve filter for blockages. If persists, contact service.

Can I pause the dishwasher during a cycle?

Yes, press the Start/Pause button to pause. Wait a few seconds before opening the door (to avoid hot steam). Close the door and press Start/Pause again to resume. Note: some cycles may restart after a delay.

How do I adjust the water softener?

Refer to the manual for the water hardness level in your area. Usually, adjust the setting via the control panel (press and hold a specific button combination). Set it to match your water hardness (e.g., level 3 for medium).

The dishwasher is leaking water. What should I do?

Check the door seal for damage or debris. Ensure the dishwasher is level. Inspect the hose connections for tightness. If the leak persists, examine the internal hoses and the water inlet valve. Turn off water supply and contact technician.

How do I use the delay start function?

Load the dishes and add detergent. Press the Delay Start button repeatedly to select the desired delay (e.g., 3h, 6h, up to 24h). Then press Start/Pause. The dishwasher will start after the set delay. The display shows remaining time.

Where can I find spare parts for my Rex R2S?

Spare parts such as racks, filters, spray arms, and detergent dispensers are available from authorized Rex service centers or online retailers. Use the model number R2S to ensure compatibility. For warranty parts, contact Rex support.

USER MANUAL R2S REX

Technical line drawing of a mechanical component with a circular housing and mounting bracket (no text or symbols)

Diagram of a mechanical device with a circular inset showing internal components (no text or symbols)

Technical line drawing of a rectangular industrial or laboratory device with internal components and labeled parts (no readable text or symbols)

Technical line drawing of a kitchen sink with faucet and valves (no text or symbols)

Technical line drawing of a mechanical assembly with a rotating component and coiled tubing (no text or symbols)

Technical illustration of a mechanical component with two views: one showing a flange labeled 'SALE' and the other showing a threaded bolt with a starburst symbol (no text or symbols present)

Line drawing of a basket filled with various kitchen utensils (no text or symbols)

Line drawing of a woven basket filled with leafy greens and fruits (no text or symbols)

Technical line drawing of a mechanical assembly with coiled components and a central shaft (no text or symbols)

Line drawing of a multi-tiered mechanical or electrical component with no visible text or symbols

Attenzione

Technical line drawing of a mechanical assembly with a cylindrical component mounted on a platform (no text or symbols visible)

Technical line drawing of a mechanical assembly with multiple components and no visible text or symbols

Uso del detersivo

6) Date il via

Diagram of a hand using a tool to lift a small device inside a circular frame, with no visible text or symbols.