PowerVault NX400 - Server DELL - Free user manual and instructions
Find the device manual for free PowerVault NX400 DELL in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | Network Attached Storage (NAS) Server |
| Form Factor | 2U Rackmount |
| Dimensions (W x D x H) | 17.09 x 24.5 x 3.44 inches (434 x 622 x 87.3 mm) |
| Weight | 35.3 lbs (16 kg) maximum configuration |
| Processor | Intel Xeon E5-2400 series, up to 8 cores |
| Memory | Up to 256 GB DDR3 ECC registered RAM (12 slots) |
| Storage Bays | 8 x 3.5" hot-swap SAS/SATA drives or 12 x 2.5" hot-swap drives |
| Storage Controller | PERC H310 or H710 RAID controller |
| Network Interfaces | 2 x Gigabit Ethernet (Broadcom 5720) |
| Power Supply | Dual redundant 550 W or 750 W hot-plug |
| Power Consumption | Typical 200-400 W depending on configuration |
| Operating System | Windows Storage Server 2012 R2 or freeDOS |
| Management | iDRAC7 with Lifecycle Controller |
| Kensington Lock | Yes, security lock slot |
| Bezel | Optional locking bezel for front drive access |
| Cooling | 5 x dual-rotor hot-swap fans |
| RAID Levels | 0, 1, 5, 6, 10, 50, 60 |
| Maintenance | Regularly clean air filters and check drive LEDs |
| Spare Parts | Hot-swap drives, PSUs, fan modules, memory DIMMs |
| Repairability | Modular design with tool-less access for most components |
Frequently Asked Questions - PowerVault NX400 DELL
How do I access the BIOS or system setup on the PowerVault NX400?
During boot, press F2 to enter System Setup. From there you can configure iDRAC, RAID, and boot order.
What is the default username and password for iDRAC?
The default credentials are root for username and calvin for password. It is strongly recommended to change these after first login.
How can I install an operating system on the NX400?
You can install OS via the optical drive, USB key, or network boot (PXE). The system supports Windows Storage Server or Linux distributions.
What do the front panel LED indicators mean?
A solid blue LED indicates normal operation; blinking amber signals a fault; solid amber indicates a non-critical error. Refer to the manual for detailed codes.
How do I replace a failed hard drive in the NX400?
Press the release button on the drive carrier, pull out the failed drive, insert a new drive of the same type, and push it in until it clicks. The RAID controller will automatically rebuild the array if configured.
The server does not power on. What should I check?
Check power cables and power supply LEDs. Try resetting by unplugging the server for 30 seconds. If using a PDU, confirm it is switched on. If still dead, may need PSU replacement.
Can I upgrade the memory on the PowerVault NX400?
Yes, it supports up to 256 GB of DDR3 ECC memory. Use registered DIMMs only. Refer to the manual for slot population order.
How do I reset the iDRAC password if I forgot it?
You can reset by booting the server and pressing F10 to enter Lifecycle Controller, then go to iDRAC Settings and reset to default. Alternatively, use the iDRAC direct USB port with a USB drive containing the reset file.
What is the recommended cleaning procedure for the NX400?
Power down and unplug the server. Use compressed air to blow dust from fans, heatsinks, and air filters. Clean the exterior with a soft damp cloth. Do not use liquid cleaners inside.
How can I update the firmware on the PowerVault NX400?
Use the Dell System Update (DSU) tool or Lifecycle Controller under F10 boot menu. You can also download firmware packages from Dell Support and apply via iDRAC.
User questions about PowerVault NX400 DELL
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Server in PDF format for free! Find your manual PowerVault NX400 - DELL and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PowerVault NX400 by DELL.