XLT-2522U - Hedge Trimmer XU1 - Free user manual and instructions

Product Type	Hedge Trimmer
Brand	XU1
Model	XLT-2522U
Blade Length	25 inches (approx. 63.5 cm)
Blade Material	High-carbon steel
Power Source	Corded electric
Power Rating	600 W
Voltage	120 V (60 Hz)
No-Load Speed	3500 strokes/min
Tooth Spacing	22 mm
Weight	3.6 kg (7.9 lbs)
Overall Length	95 cm
Handle Type	D-loop rear handle with soft grip
Safety Features	Two-hand operation, blade guard, lock-off switch
Cutting Capacity	Up to 20 mm branch thickness
Maintenance	Clean and lubricate blades after each use; sharpen periodically
Spare Parts Available	Blade assembly, motor brushes, switch, power cord
Certifications	ETL, CE, RoHS

Frequently Asked Questions - XLT-2522U XU1

How do I start the XU1 XLT-2522U hedge trimmer?

Ensure the power cord is plugged into a grounded outlet. Press and hold the safety lock-off trigger, then squeeze the main switch trigger. Release the lock-off and continue squeezing the main trigger to run.

What is the correct way to hold the hedge trimmer?

Hold the rear handle with your dominant hand and the front handle (if equipped) with your other hand. Keep both hands on the handles at all times. Do not use one-handed.

How do I clean the blades after use?

Disconnect the trimmer from power. Use a soft brush or cloth to remove debris. Apply a light coat of lubricating oil (e.g., WD-40) to the blade teeth to prevent rust.

Can I sharpen the blades myself?

Yes, but only if you have experience. Use a fine file or a sharpening stone, following the factory bevel angle (typically 45 degrees). For safety, it is recommended to have a professional sharpen them.

What size extension cord should I use?

Use a heavy-duty outdoor extension cord rated for the tool's amperage (approx. 5 A). For lengths up to 50 ft, use 14 AWG; for 50-100 ft, use 12 AWG to minimize voltage drop.

Why does the trimmer stop suddenly while cutting?

It may be due to overload protection. Release the trigger and let the tool cool for a few minutes. If it continues, check for a jammed branch or a faulty power connection.

How often should I lubricate the blades?

Lubricate the blades before each use and after cleaning. During prolonged use, apply oil every 30 minutes to keep the blades running smoothly.

Can I use the hedge trimmer in wet conditions?

No. This trimmer is for outdoor use but never in rain or wet foliage. Moisture increases the risk of electric shock and damage to the tool.

How do I store the hedge trimmer?

Clean the blades and apply oil. Hang the trimmer by the handle or place it in a dry storage area. Use the blade guard to protect the teeth and prevent injury.

What spare parts are available for this model?

Common spare parts include the blade assembly, motor brushes, switch, and power cord. Contact XU1 customer support or authorized dealers for genuine parts.

USER MANUAL XLT-2522U XU1

Telephone: GB: 0151 294 4488 / IRL: 1850 882711

XLT-2522U 1917

SAFETY

INSTRUCTIONS

WARNING! When using mains-powered equipment, basic safety precautions, including the following, should always be followed to reduce risk of fire, electric shock, personal injury and material damage.

Electrical safety

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool.

Save these instructions and other documents

supplied with this tool for future reference.

Before you connect the equipment to the mains

supply make sure that the data on the rating plate are identical to the mains data.

This tool is double insulated, therefore no earth wire is required.

If the supply used is damaged, it must be replaced.

In the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to

avoid a hazard.

Note: Double insulation does not take the place of

normal safety precautions when operating this tool.

Using an extension lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the

the power input of this test. Before use, inspect the extension lead for signs of damage, wear and ageing

Replace the extension lead if damaged or defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead

driving the tool completely, 500 of an extension tool not suitable for the power input of the tool or which is

damaged or defective may result in a risk of fire and electric shock.

Description of symbols

Description of symbols

Read the instruction manual before

Hood the instruction manual before starting!

(1)

(

Pull out the mains plug before

checking a damaged power cable

→ 2024

Keep other people out of the dream are!

of the danger area!

continues to

Caution: Sharp blade! Keep your hands AWAY.

Decibel level

[Non-Text]

Wear ear-inulls. The impact of noise ca

1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 99.

Vibration emission value ah = 6.53 m/s ²

K uncertain

Warning

The specified vibration value was established in

accordance with a standardized testing method. It may change according to how the electric review

may change according to how the electric equipment is used and may exceed the specified value in

exceptional

The specified vibration value can be used to compa

The operating variation value can be used to compare the equipment with other electric power tools.

The specified vibration values can be used for initial

The specified violation value can be used for initial assessment of a harmful effect

2023.10.19

Keep the noise emissions and vibrations to a

• Only use appliances which are in perfect working

only also applied to which are in person's home order.

• Service and clean the appliance regularly.

- Adapt your working style to suit the appliance. - Do not overload the appliance.

• Have the appliance serviced whenever necessary

- Switch the appliance off when it is not in use.

- wear pro

Residual ri

Even if you use this electric power tool in accordance with instructions, certain practical

accordance with instructions, certain residual risks cannot be rules out. The following hazard

Tisks cannot be turns out. The following hazard may arise in connection with the equipment's

construction and layout:

1. Lung damage if no suitable protective dust mass is used

2. Damage to hearing if no suitable ear protection

used.

1. Health damage caused by hand-arm vibrations the equipment is used over a prolonged period of

the equipment is used over a prolonged period of not properly guided and maintained.

General Power Tool Safety

Warnings

2.1.1.

WARNING! Read all safety

warnings and all instructions. Failure

To follow the warnings and instructions may result in electric shock, fire and/or serious

result in elastic shock, life and/or serious injury.

Save all warnings and instructions

for future reference. The term "power tool" in all of the warnings refers to your

tool "in all of the warnings" refers to your mains-operated (comped) power tool or battery-

mano operated (cordless) power tool or battery operated (cordless) power tool.

1. Week

1. work area safety a. Keep work area

dark areas invite accidents.

b. Do no

atmospheres, such as in the presence of flammable liquids, gases or dust. Bouns tools

create s

c. Keep

operating a power tool. Distractions can cause you to lose control

12.000

1. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodified plugs and matriting outlets will reduce risk of electric shocks.

b. Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed.

or grounded.

c. Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase the risk of electric shock

d. Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e. When operating a power tool outdoors, use an extension and suitable for outdoor use

an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

1. If operating a power tool in a damp location is unobservable, use a residual current

is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

1. Persor

a. Stay alert, watch

use common sense when operating a power tool. Do not use a power tool while you

tool. Do not use a power tool while you are tired or under the influence of drugs.

alcohol or medication. A moment of inattention

while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always

wear eye protection. Protective equipment such as

dust mask, non protection used

personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before

the switch is in the on-position before connecting to power source and/or battery.

pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energising power tools that have the switch on irriter accidents.

1. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power fool in unexpected situations.

1. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

of jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes

jewellery or long hair can be caught in moving parts.

1. If devices are provided for the connection of dust extraction and collection facilities

of dust extraction and collection facilities, ensure these are connected and properly

used. Use of dust collection can reduce dust-related

hazards. b) Do not let familiarity gained from

frequent use of tools allow you to become

complacent and ignore tool safety principles. Limiting action on severe severity injury

principles. A careless action can cause severe injury within a fraction of a second,

1. Production volume and cost

2. Power tool use and care Do not force the power

power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power

source and/or remove the battery pack

if detachable, from the power tool bet making any adjustments, changing

making any adjustments, changing accessories, or storing power tools.

preventive safety measures reduce the risk of starting the

1. Store idle power tools out of the reac

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power too tools are dangerous in the hands of untrained us

e. Maintain power tools and accessories.

Check for misalignment or binding of moving parts, breakers of parts and

moving parts, breakage of parts and a other condition that may affect the po

tool's operation. If damaged, have the

power tool repaired before use. Many are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

- Use the power tool, accessories and

1. Use the power tool, assessions and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to be

working conditions and the work to be performed. Use of the power tool for operation

different from those intended could result in a hazardous

situation. b) Keep handles and grasping surfaces dry

1) Keep handled and grasping surfaces dry, clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for safe

handling and control of the tool in unexpected sit

5. Service

a. Have your power tool serviced by a qualified repair person using only ide

replacement parts. This will ensure that the

of the power tool is maintained.

Electric Line Trimmer Safe

Warnings

Warnings • Before you begin

- Before you begin your work, examining the material you want to cut. Remove any foreign bodies. Continue to watch out

for foreign bodies while you are working. If you come across

any foreign bodies while cutting, turn off the machine and remove the items in question

• Work only when visibility is adequate

• Make sure you stand squarely at all times while working. B

careful when walking backwards. Thipping hazard! Never leave the equipment unorganized in the work area

- Never leave the equipment unsupervised in the work area. If you stop work for a while, leave the equipment in a safe

place.

• If you stop your work in order to go to another area to work, you must make sure that the equipment is switched off with

you must make sure that the equipment is switches or will you are going there.

- Never use the equipment while it is raining or in damp or

- Wet surroundings. - Protect your equip

• Before you switch on the equipment, check that the cutting

unit will not touch any stones or other objects.

• Always wear suitable working clothes to prevent injuries to the head, hands and feet. For this purpose we've helmet

the head, hands and feet. For this purpose wear a helmet, safety goggles (or visor), high boots (or strong shoes and

long trousers made of tough fabric) and work gloves.

- When the equipment is in operation, you must always hold it away from your body!

• Do not switch on the equipment when it is turned around or

when it is not in working position

- Switch off the machine and pull out the power plug: when the equipment is not being used, when you let

When the equipment is not being used, when you feel it unsupervised, when checking the equipment, when

removing or replacing the spool, or when transporting the

equipment from one place to another. - Keep the equipment away from other people, especially

Help the equipment away from other people, especially children, and from pets. There may be stones and other

objects in the grass that is cut and thrown up. - When you are working, keep a distance of at least 5 m

When you are learning, help us attain a similar form from other persons and pets.

- Do not cut against hard objects. This will help you to prevent causing injury to yourself and damage in the

problem addressing injury to year-old and damage to the equipment.

- Use the edge of the safety guard to keep the equipment away from walls, different surfaces and fragile objects.

- Never use the equipment without the safety guard.

• This equipment is not allowed to be used by children or by persons with reduced physical, severity or mental

or by persons with released physical, sensory or mental capacities or those with a lack of experience and

knowledge. Children should be supervised so that they do not play with the equipment. Children are not allowed

to carry out the cleaning or maintenance.

- Avoid abnormal working postures. Make sure you stand squarely and keep your balance at all times. Always

maintain good footing on inclines. Only operate the

- Risk of injury from dangerously

• The moving parts are not allowed to be tough

the power plug has been removed and all moving parts have come to a complete standstill.

- Read the directions with due care. Familiarize yourself

with the operator controls and proper operation of the equipment.

- Never allow children or other persons who are not families with the exception instructions to use the

familiar with the operating instructions to use the equipment. Contact your local governmental age

information regarding minimum age requirements for the years

• Always keep in mind that the user of the equipme

is personally responsible for accidents or hazards involving other persons or their property.

• Before use, always carry out a visual check to ma

sure that the safety devices or covers are not missing or damaged and that they are correctly fitted.

- damage and that they are mostly hard. - Never use the equipment in bad weather conditions an

particularly never when there is a risk of lightning.

- Never use the equipment with a damaged cover or safety device or when a cover or safety device is

missing. • Switch on the motor only when there are no hands or

- Option on the motor only when there are no hands of feet within range of the cutting unit.

• Always switch off the equipment and pull out the power

plug: - when the equipment is left unattended - before you remove a blockage

- before you inspect, clean or work on the equipment

- after the equipment strikes a foreign body when the equipment begins to make sure

- when the equipment begins to make unusual violations (examine immediately) The equipment is not allowed to

be put into operation again until the cause of the unusual

vibrations is eliminated. If you fail to find the cause of the vibrations, contact a service centre.

- Risk of injury from the cutting unit! Keep hands and feet

away from the cutting unit

- Use only spare parts and accessories which are recommended by the manufacturer.

• Examine and service the equipment regularly.

IMPORTANT! The safety guard is then

Figure 1. The safety guard is there to ensure your safety and the safety of other

It is also essential for the equipment to work

correctly. Failure to comply with this instruction will invalidate your warranty as well as create a

potential source of danger

- Never use your hands to try to stop the cutting unit. Always

Wait for it to stop by itself. • Use only require cutting unit

- Use only genuine eating units. - Make sure that the air vents are free of dirt.

• Do not try to use the equipment to cut grass which is not

growing on the ground; for example, do not try to cut grass growing on walls or stones, etc.

• The person operating the grass trimmer is liable for any

damages sustained by third parties within the equipment's

working radius as a result of its use.

• Do not cross loads or gravel pairs with the equipment, switched on.

- When you are not using t

place out of the reach of children. • Use the equipment only in the way described in these

operating instructions and always hold it perpendicular

to the ground. Every other position is dangerous. • Check at regular intervals that the screws are properly

tightened.

• The area to be cut must a cables and other objects.

- If the equipment has to be lifted for transporting, be sure

to switch off the motor first and wait for the cutter to come to a standstill. Each time you leave the equipment

switch off the motor.

• Under no circumstances are you to cut against hard objects during use. This is imperative to prevent injury to

yourself and damage to the equipment.

- Use only original replacement parts for repairs. - Before starting up the equipment, and after any

check the equipment for signs of wear or damage and

have any necessary repairs carried out. • Always keep your hands and feet away from the cutting

unit, especially when switching the motor on.

• Pull out the power plug before checking, cleaning or doing any work on the equipment and when it is not

being any staff on the equipment and other is not being used.

• Acquaint yourself with the controls and how to use the tool.

- Stop using the equipment when there are people –

particularly children – or pets nearby. • Never use the mining if protective equipment is

- Never use the machine's provisional equipment, or damaged or missing.

- Never mount metal c

• Electrically powered trimmers should be repaired only by authorized persons.

• Use only spare parts recommended by the

• Before use, you must check the power cable and

extension cable for signs of damage and wear.

- Keep the power cable and the extension cable aw from the cutting unit.

- If the cable is damaged during operation, it must disconnected immediately from the power supply.

SPECIFICATIONS

Voltage: 230-240V ~ 50Hz
Power:	250W
No Load Speed: 12,000min
Cutting Diameter: 220mm
Cutting Line:	1.2mm
Weight:	1.4kg

Items Supplied

Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service centre or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions. • Open the packaging and take out the equipment with care.

- Remove the packaging material and any packaging and/or transportation hardware (if available).

transportation braces (if available).

• Inspect the equipment and accessories

damage.

- If possible, please keep the packaging until the end of the

Proper Use

The equipment is designed for cutting lawns and small areas of grass in private and hobby gardens. Equipment designed for use in private and hobby gardens is regarded as unsuitable for use in public facilities, parks and sports centres, along roadways, or in agriculture and forestry. The operating instructions as supplied by the manufacturer must be kept and referred to in order to ensure that the equipment is properly used and maintained.

important. This equipment must not be used for composting purposes (shredding) as this could result in injury or damage to property.

The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for equivalent

ASSEMBLY

Housing Assembly

1. Fit the upper handle section and motor housing section into the middle housing section, insert it as far as possible. FIG. A.

Note: The three sections will only go together one

1. Secure all three sections with the four supplied assembly screws. FIG. B.

Blade Guard

1. Turn the line trimmer upside down
2. Place the blade guard over the spool & line, making
   sure to align both the ridges of the blade guard
   with the grass trimmer housing
3. Rotate blade guard anti-clockwise FIG. C
4. Closure with the supplied screw FIG. D

1. 2017年1月1日

Before using the Line Trimmer

1. Ensure the switch is in the off position and disconnect the cable plug from the mains

disconnect the stable plug from the main supply.

1. Examine the general condition of the tool. Inspec

the guard, switch, power cord. Check for loose screws, miscalignment, binding of moving parts

improper mounting, broken parts and any other

condition that may affect its safe operation.

If abnormal noise or vibration occurs during

operation, turn the line trimmer on imbed and have the problem corrected.

Increasing the Cutting Line

1. Before starting ensure the cutting line is the correct

length. Pull the cutting line to the edge of the safety guard

The Wilson Conference on the 1980s, the United States

1. If the line is to short push down on the bump knob and at the same time pull the line out as first it

extends a few centimetres past the edge of the

guard FIG. E.

1. To increase the cutting line length during operation

tap the bump knob onto the ground, preferably a

hard surface. Do not hold the bump knob on the

ground as this may overload the unit.

OPERATION

On/Off Trigger

1. To switch ON, reverse the On/OW switch F16.5

2. To obtain one, otherwise the other obtain field:

3. To turn OFF release the On/Off trigger.

[EMPTY]

Using the Line Trimmer

- Wear eye protection and stout shoes at all times

operating the grass trimmer.

3.1.1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.50.51.52.53.54.55.56.57.58.59.60.61.62.63.64.65.66.67.68.69.70.71.72.73.74.75.76.77.78.79.80.81.82.83.84.85.86.87.88.89.90.91.92.93.94.95.96.97.98.99.100

- Start cutting near the mains power source and work away to make it easier to guid the

extension cord.

[Non-Text]

- Never use the line trimmer without its safety devices.

001910.

- Do not cut grass that is wet. (The best results are achieved on dry grass)

achieved dry grass).

- Wait until the line trimmer reaches full speed

before cutting the grass

- Move the line trimmer from side to side so you

walk forward, holding it at an angle of appruy.

30° Light cuts are better than heavy cuts as the

allow the cut grass to fall away from the cutting

head). FIG. G.

- Keep the grass trimmer away from hard objects

order to avoid unnecessary line wear.

(三) 2017年1月1日

- Several passes will be required to cut long grass as shown. FIG. 14

as a result of

• To prevent the line from breaking ensure you

approach the edge/object slowly

• Watch out for kickbacks in the event of impact

with hard objects.

1.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.50.51.52.53.54.55.56.57.58.59.60.61.62.63.64.65.66.67.68.69.70.71.72.73.74.75.76.77.78.79.80.81.82.83.84.85.86.87.88.89.90.91.92.93.94.95.96.97.98.99.100

- After finishing the cutting operation, keep the head close to ground level, replace the switch on

allow the motor to come to a complete standstill

Unplug and place the line trimmer on the ground

“

- Keep ventilation slots of the 3mmirr clean at an time. Diversically clean out the erase frame the

cutting head and the rim of the blade guard to

ensure efficient operation at all times.

MAINTENANCE

Replacing Line Spool

1. Holding the line trimmer upside down. Rotate the

spool cover anti-clockwise to the unlock position.

Lift off the spool cover and remove the empty

spot.

Note: Ensure not to misplace the spring.

1. Thread the end of the line from the new line one

through the eyelet in the snool mount and allow

approx. 10 cm of line to project FIG I.

1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 99.

2. Holding the line thriller upside down in the coming into the spin housing assembly, such the

spool and spool cover back into the spool housing

Rotate clockwise to lock the spool in position.

Notes: When you start the line trimmer again the line

Note: When you start the timmer again the line will be cut to the perfect length automatically.

- Keep ventilation slots of the line trimmer clean at all times. Periodically clean out the grass from the cutting head and the rim of the blade guard to ensure efficient operation at all times.

- After each use, blow air through the tool housing to ensure it is free from all dust, dirt, etc. Build up of dust, dirt particles may cause the tool to overheat and shorten the life of the tool.

- Never let any liquid get inside the tool, never immerse any part of the tool into liquid.

- Do not use cleaning agents to clean the plastic parts of the tool. A mild detergent on a damp cloth recommended. Water must never come into costs

with the tool.

- When not in use, the tool should be stored in a dry, frost-free location, out of the reach of children.

• No lubrication is necessary as the motor is equipped

with lifetime-lubricated bearings Note: XU1 will not be responsible for any damage or injuries caused by the repair of the tool by an

unauthorised person or by mishandling of the tool.

For 20 countries only

Never place any electric power tools in your household

To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric power tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request: As an alternative to returning the equipment to the manufacturer, the owner of the electrical equipment must make sure that the equipment is properly disposed of if he no longer wants to keep the equipment. The old equipment can be returned to a suitable collection point that will dispose of the equipment in accordance with the national recycling and waste disposal regulations. This does not apply to any accessories or aids without electric components supplied with the old equipment.

The reprinting or reproduction by any other means, in who or in part, of documentation and papers accompanying products is permitted only with the express consent of the ISC GmbH.

SERVICE INFORMATION

Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required for use as consumables..

* Not necessarily included in the scope of delivery!

SPARE PARTS

Spare parts can be ordered from the Special Orders Desk at your local Bunnings Warehouse or Homebase store. For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service: Great Britain: 0151 294 4488 Ireland: 1850 882711 E-mail: [e-mail]

WARRANTY

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the customer service number shown. Please note the following terms under which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer mentioned below promises to buyers of its new products in addition to their statutory guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or manufacturing faults on a product which you have bought from the manufacturer mentioned below are limited to either the rectification of said defects on the product or the replacement of the product, whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional applications. A guarantee contract will not be created if the device has been used by commercial, trade or industrial business or has been exposed to similar stresses during the guarantee period.

1. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to incorrect installation, a failure to follow the operating instructions (for example connecting it to an incorrect mains voltage or current type) or a failure to follow the maintenance and safety instructions or by exposing the device to abnormal environmental conditions or by lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the device or the use or unapproved tools or accessories), ingress of foreign bodies into the device (such as sand, stones or dust, transport damage), the use of force or damage caused by external forces (for example by dropping it). - Damage to the device or parts of the device caused by normal or natural wear or tear or by normal use of the device.

1. Your Product is guaranteed for a period of 12 months from the original date of purchase and is intended for DIY (Do It Yourself) use only. Warranty excludes consumable parts, for example: cutting blade. Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or parts fitted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables and missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE HELPLINE GB: 0151 294 4488 IRL: 1850 882711

XU1

Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG