Gorilla GLW-10 - Subwoofer SPL - Free user manual and instructions
Find the device manual for free Gorilla GLW-10 SPL in PDF.
User questions about Gorilla GLW-10 SPL
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Subwoofer in PDF format for free! Find your manual Gorilla GLW-10 - SPL and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. Gorilla GLW-10 by SPL.
USER MANUAL Gorilla GLW-10 SPL
Thank you for choosing SPL woofers. Designed and engineered in the USA, this product combines innovative technology with the finest materials to consistently deliver Absolutely State of the Art performance, sound quality, reliability, and value. This SPL product reflects our commitment to offer you unparalleled performance and quality for years of dependable service and listening enjoyment.
Features, Parameters, & Dimensions
Polypropylene Cone
Rubber Surround
2.5" 4-layer VC on Aluminum Former Nickel Plated 8ga. Compression Terminals
Vented T-Yoke Back-plate
Polpropylene Molded Dust Cap
Textured Basket with Voice Coil Cooling
Poly-Cotton Suspension Spider
GLW-10 GLW-12 GLW-15
| IMPEDANCE | |||
| RE | |||
| Fs | |||
| QES | |||
| QMS | |||
| QTS | |||
| LE | |||
| DIAMETER | |||
| SD | |||
| VAS | |||
| BL | |||
| MMS | |||
| CMS | |||
| SEN | |||
| RMS/MAX | |||
| CUTOUT DIAM. | |||
| MOUNTING DEPTH |
Enclosure Dimensions
Included in this manual are a number of different enclosure suggestions. These are by no means the only enclosures to use, but the provide a starting point to determine the correct enclosure for your needs many factors must be addressed (amount of power, vehicle, placement, crossovers, etc) Therefore, as always, SPL recommends that your subwoofer be installed by an authorized SPL dealer.
Enclosure Construction
All enclosures should be made of .75" (3/4") material only. When possible, make the baffle 1.5" (1 12 ) thick and add .75" (3/4") to the depth of the enclosure to compensate. All volumes INCLUDE vent/port and subwoofer displacements. DO NOT change the volume unless you plan on adding a substantial amount of bracing. For added performance, applying a coat of fiberglass resin to the interior walls will greatly improve sealing the enclosure. Adding a thin layer of poly-fill will improve response by smoothing out reflections within the enclosure.
Enclosure Recommendations
GLW-10 GLW-12 GLW-15
| SEALED | |||
| MIN | .75 CU FT. | 1.0 CU FT. | 1.5 CU FT. |
| OPT | 1.0 CU FT. | 1.5 CU FT. | 2.75 CU FT. |
| PORTED | |||
| MIN | 1.0 CU FT. | 1.5 CU FT. | 1.75 CU FT. |
| PORT WxL | 3INCH x 5.5INCH | 4INCH x 5INCH | 5INCH x 7.8INCH |
| F3 Hz | 34 | 38 | 30 |
| OPT | 1.5 CU FT | 2.25 CU FT. | 2.75 CU FT. |
| PORT WxL | 4INCH x 6INCH | 6INCH x 7INCH | 6INCH x 7INCH |
| F3 Hz | 32 | 34 | 28 |
