Ferm

FTHT-12V - Hedge Trimmer Ferm - Free user manual and instructions

Find the device manual for free FTHT-12V Ferm in PDF.

📄 22 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice Ferm FTHT-12V - page 1
Pick your language and provide your email: we'll send you a specifically translated version.
Product Type Telescopic Hedge Trimmer
Brand Ferm
Model FTHT-12V
Battery Voltage 12 V
Battery Capacity 3 Ah
Charger Input 230-240 V~, 50 Hz
Charge Time 12 hours (first charge: 16 hours)
No-Load Speed 1500/min
Weight 1.4 kg
Sound Power Level 95.0 dB(A)
Vibration Value 0.6 m/s²
Adjustable Head Angle Yes, via button on side
Telescopic Handle Yes, adjustable length with lever
Blade Guard Included for transport and storage
Unlock Button Prevents accidental starting
Carrying Belt Included for battery pack
Contents of Packing Hedge trimmer, battery, charger, belt, blade guard, instructions, warranty card
Maintenance No lubrication required; clean with charger unplugged and battery removed
Storage Dry, frost-free place; recharge battery every 1-2 months
Disposal Battery contains toxic materials; dispose at environmentally safe centre

Frequently Asked Questions - FTHT-12V Ferm

How long does it take to fully charge the battery?
The battery needs 12 hours to fully charge from flat. For the first use, charge it for 16 hours.
Can I adjust the cutting head angle?
Yes, press and hold the button on the side of the head, adjust to the desired angle, then release the button to lock it.
How do I extend the handle?
Grip the head firmly, lift the lever on the upper handle, adjust the length, then press the lever down to lock.
How do I start and stop the hedge trimmer?
Press and hold the unlock button, then squeeze the main switch to start. Release the main switch to stop.
Is it safe to use in rain?
No, do not use the hedge trimmer in rain or wet conditions. It is not waterproof.
What should I do if the battery leaks?
If liquid contacts skin or clothes, wash with warm soapy water. If it gets in eyes, rinse with clean water for 10 minutes and seek medical attention.
How should I store the hedge trimmer for long periods?
Fully discharge the battery, then recharge for 12 hours. Store in a dry, frost-free place. Recharge every 1-2 months during winter.
Does the trimmer require lubrication?
No, the machine requires no additional lubrication.
How do I dispose of the battery?
The battery contains toxic materials. Dispose of it at an environmentally safe waste disposal centre.
What is covered under warranty?
Warranty conditions are on the enclosed card. Wear of the hedge trimmer is not covered.

User questions about FTHT-12V Ferm

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

The email remains private: it is only used to notify you if someone responds to your question.

No questions yet. Be the first to ask one.

Download the instructions for your Hedge Trimmer in PDF format for free! Find your manual FTHT-12V - Ferm and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. FTHT-12V by Ferm.

USER MANUAL FTHT-12V Ferm

UK Subject to change

Fig.2
Ferm FTHT-12V - 1

natural_image Simple line drawing of a mechanical device with no text or symbols

Fig.4

Ferm FTHT-12V - 2

natural_image Pure mechanical diagram showing a tool interacting with a bracket (no text or symbols)

Fig.3

2 Ferm

EXPLODED VIEW SPARE PARTS LIST FTHT-12V FERM NR DESCRIPTION REF NR 501487 POWER CORD 1 501488 SWITCH 9 HGA1002 BATTERY 7 501489 CUTTING BLADE 45 501490 BLADE COVER 47 501491 GUARD 48 501492 TELESCOP LOCKING 21 TILL 23 501493 CHARGER -

Ferm 43

uk English

TELESCOPIC HEDGE TRIMMER

THE NUMBERS IN THE FOLLOWING TEXT CORRESPOND WITH THE PICTURES AT PAGE 2

SAFETY AND OPERATING INSTRUCTIONS For your own safety and for the safety of others, please read these instructions carefully before using this appliance. Keep in a safe place for future reference.

Warning! Always read the instruction for electrical products carefully before use. It will help you understand your product more easily and avoid unnecessary risks. Keep this instruction manual in a safe place for future use.

CONTENTS:

  1. Machine data
  2. Safety instructions
  3. Assembly
  4. Use
  5. Service & maintenance

I. MACHINE DATA

INTRODUCTION

The machine is intended for cutting and trimming hedges and bushes in domestic use. Adjusting the head angle of the machine allows comfortable cutting at a variety of angles. The extension tube adjustment allows reaching difficult places without the use of a ladder.

TECHNICALSPECIFICATION

Adaptor charger | 230-240 V-, 50 Hz
Battery pack | 12 V=,3 Ah
Charge time | 12 hr
No-load speed | 1500/min
Weight | 1.4kg
Sound power level | 95.0dB (A)
Vibration value | 0.6 m/s,

FEATURES

Fig.1

  1. Main unit
  2. Main switch
  3. Unlock button
  4. Guard plate
  5. Cutting blade
  6. Blade guard
  7. Headanglelock
  8. Release lever
    9 Plugpowercord
  9. Battery pack
  10. Battery/pack/rocker
  11. Charger plus
  12. charge, plug
  13. Battery charger

CONTENTS OF PACKING

I Telescopic hedge trimmer

1 Battery

I Battery charger

1 Carrying belt

1 Protection guard

  1. Information

1 Safety instructions

1 Instruction manual

I Warranty card

2. SAFETY INSTRUCTIONS

EXPLANATION OF SYMBOLS

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 1

Read the instructions.

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 2

In accordance with essential applicable safety standards of European directives

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 3

Class II machine - Double insulation - You don't need any earthed plug.

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 4

Risk of damaging material and/or physical injuries

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 5

Keep bystanders at a distance

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 6

Always recycle batteries

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 7

Indoor use only

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 8

Thermic protector

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 9

Do not use in rain.

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 10

Wear eye and ear protectors

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 11

Sound power level

Ferm FTHT-12V - EXPLANATION OF SYMBOLS - 12

Faulty and/or discarded electrical or electronic apparatus have to be collected at the appropriate recycling locations.

GENERAL SAFETY INSTRUCTIONS

  • Never touch the blade of this appliance with any part of your body unless the battery has been removed first.
  • Dispose of plastic bags safely - they are a suffocation hazard for young children.
  • Never use this appliance without the blade guard fitted. It must always remain fitted.
    • Do not expose tools to rain
  • Keep the area you are working in clean and tidy.
  • If you are using a means of support to raise yourself off the ground, ensure that it is stable and cannot topple over - do not overreach at any time.

  • Do not use power tools in the rain or wet environments.

  • Do not use power tools where there is a risk of fire or explosion - i.e. near flammable liquids or gases.
  • Do not allow children into the area where you are working.
  • Do not let children or other people touch power tools.
  • Do not leave the power tool unattended and always remove the battery from the appliance after use.
  • Store in a dry place well out of reach of children.
    • Always use safety glasses and a dust mask when cutting or drilling through materials. We also recommend the use of ear protectors and glo
  • Wear the right clothes - not loose fitting or jewellery and ensure garments cannot come into contact with moving parts.
  • Wear non-slip shoes, especially when working outdoors. Do not wear sandals or open-toed shoes.
    • If you have long hair, tie it back safely to avoid tangling it in moving parts.
  • Before using any power tool, check first for damaged parts and if found do not use them before the part or parts have been replaced with new ones.
  • Do not use power tools when you are tired or have been drinking alcohol.
  • Ensure the power switch is in the OFF position before inserting the battery.
  • Never carry the tool / charger by the cord or yank it to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges.
  • Keep the cutting tools sharp (regular maintenance, replacement, sharpening) and clean for better performance.
  • Do not force the appliance - let it work at the rate for which it was intended.
  • Do not overreach while working - you may lose your balance.
  • You must switch off your tool at the tool's on/off switch.
  • Never change a blade or any other attachment without first removing the battery from the appliance.
    • Always fit the blade cover when the tool is in transit or in storage.
  • Only use spare parts and attachments supplied by Ferm. Use of attachments other than those supplied or recommended by Ferm will invalidate your guarantee and could be dangerous.
  • Only use this appliance for its intended purpose - trimming hedges and bushes

Ferm FTHT-12V - GENERAL SAFETY INSTRUCTIONS - 1

Above all - be careful!

• Always ensure all handles and guards are fitted when using the tool.

- Never attempt to use an incomplete machine or one fitted with an unauthorised modification.

• Before cleaning the hedge trimmer remove disconnect the battery from the machine.

- Check cutting blades regularly for damage, and if damaged repair immediately.

• Never allow children to use the tool
• After use the tool should be stored so that the blade is not exposed (always use the transport protection)

ADDITIONAL SPECIAL SAFETY WARNING FOR THE BATTERY CHARGER

- The charger is specifically designed for use from a standard domestic electricity supply 230 - 240 volts. Do not attempt to connect it to any other power supply.

- Please read and follow the instructions printed on the charger and battery

• The battery must be charged indoors only - in a clean dry place.

- Use the charger only for the battery type which is included.

Warning: If the battery is cracked or damaged or has received a heavy knock you must not insert it into the charger. There is a risk of electric shock or electrocution. The battery must be replaced and the damaged battery disposed of safely.

Ferm FTHT-12V - ADDITIONAL SPECIAL SAFETY WARNING FOR THE BATTERY CHARGER - 1

Ensure the charger and the charger lead is not placed where it can be tripped over or stepped upon.

Warning: Do not allow liquid of any kind to come into contact with the charger. There is a risk of electric shock. The battery must be completely dry before being inserted into the charger.

- Allow the battery to cool down after use by leaving it in a safe, cool well-ventilated place out of reach of children.

- Do not attempt to charge the battery with any other charger than the one supplied with this product.

- Do not attempt to dismantle the charger - if it is not working take it to your nearest authorised service centre for repair.

- Always store the charger, battery and appliance in a safe, dry place where the temperature cannot exceed 40^ (104F) e.g. in the open exposed to direct sunlight under glass or alongside metal fabrications.

- Keep out of reach of children.

• If the battery leaks very slightly this may not indicate that the battery is faulty and may only be temporary. However, if the liquid comes into contact with your skin or clothes, wash the affected area quickly in warm, soapy water.

- If the liquid gets in your eyes, wash your eyes with clean cool water for a minimum of 10 minutes and seek medical attention immediately afterwards.

• Never throw your battery on a fire

3. ASSEMBLY

MOUNTING THE GUARD PLATE

Fig. 1

- Place the guard (4) on the machine as shown in the picture

- Mount the guard with help of the screw

GARANTI

98/37/EOF, 73/23/EOF, 89/336/EOF,

01-10-2004 ZWOLLENL W. Kamphof Quality department

Ferm FTHT-12V - 98/37/EOF, 73/23/EOF, 89/336/EOF, - 1

The head of the trimmer can be adjusted up or down.

This allows comfortable cutting at a variety of angles.

- Grip the head of the trimmer and press and hold the button on the side.

- Adjust the head to the desired angle.

- Release the button to lock the head in the selected position.

EXTENSION TUBE ADJUSTMENT

Fig. 4

The handle length on this product can be varied, allowing

you to reach difficult places without the use of a ladder.

• Grip the head of the product firmly; lift the lever on the upper handle.

- Press the lever firmly down to lock the handle

Important: Do not charge your battery in a very cold room (below 5°C) or above 40°C (104F).

4. USE

CARRYING THE BATTERY PACK

Wear the carrying belt with battery pack across your chest to ensure it does not swing around.

STARTING AND STOPPING

Fig.

The handle is designed with an unlock button to prevent accidental starting.

- Remove the blade guard (6)

- Press and hold the unlock button (3) located on either side of the handle, then squeeze the main switch (2).

- Release the main switch to stop the blades.

Ferm FTHT-12V - Fig. - 1

Wait for it to stop before releasing your grip on the handle or putting your hand near the cutting area.

USING THE BATTERY CHARGER

Fig. 2

The battery has to be disconnected from the machine to charge it.

- Rotate the metal retaining ring counter clockwise - Pull the socket from the battery

- Connect the battery charger correctly to the socket on the battery (see the notch in the plug) and plug the charger into the mains.

• The battery needs a full 12 hours to charge fully from flac.

• The battery will not be damaged if left on charge over 12 hours.

Ferm FTHT-12V - Fig. 2 - 1

Before first use charge the battery for 16 hours

Ferm FTHT-12V - Fig. 2 - 2

Never store the product with a flat battery

TRIMMING A HEDGE-BEST METHOD

- Ideally a hedge should be wider at the bottom than the top. This will improve light penetration, keeping the hedge healthy. If possible, trim both sides of the hedge.

- When trimming the sides of the hedge, trim from the bottom upwards. This will ensure there are no hedge trimmings obscuring or interfering with your cut strokes.

• The blade should not be forced to cut too deep. Cut lightly through the surface of the hedge.

- When trimming the top of the hedge, trim away from you but do not over-reach. It is much wiser and safer to move along and cut within your reach remaining on two feet at all times.

Warning: Do not let the blade come into contact with wire meshing or fencing material. It could damage the material and your trimmer.

STORAGE

When storing the machine for longer than 6 weeks:

• Fully discharge the battery (by running the product) and then recharge the battery for 12 hours.

• Store in a dry and frost-free place.

- Recharge the battery every 1 or 2 months during the winter, because the battery will discharge slowly.

5. SERVICE & MAINTENANCE

CLEANING

To reduce the risk of electric shock the charger must be unplugged from the power supply and the battery removed before cleaning (or maintaining) the charger.

LUBRICATION

The machine requires no additional lubrication.

ENVIRONMENT

You battery contains materials that are considered toxic. Dispose of the battery through an environmentally safe waste disposal centre.

FAULTS

Should you experience any problems at all with this product or require spare parts, ring your nearest authorised dealer.

WARRANTY

The warranty conditions can be found on the separately enclosed warranty card. Wear of the hedge trimmer is not covered by the warranty.

CE DECLARATION OF CONFORMITY (UK)

We declare under our sole responsibility that this product conforms with the following standards or standardised documents:

EN60745-1, EN774, EN55014-1, EN55014-2

in accordance with regulations:

98/37/EEC, 73/23/EEC, 89/336/EEC

from 01-10-2004 ZWOLLENL W. Kamphof Quality department

Ferm FTHT-12V - 98/37/EEC, 73/23/EEC, 89/336/EEC - 1

It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice.

Ferm B.V, Zwolle, The Netherlands

D Deutsch

TELESKOPHECKENSCHERE

- Bortskaf plastposer sikkert – under leg kan små born kvæles i dem.

5. SERVICE OG VEDLIKEHOLD

RENGJ∅RING

CE ERKLÆRING AV ANSVARSFORHOLD (N)

98/37/EOF, 73/23/EOF, 89/336/EOF

98/37/ETY, 73/23/ETY, 89/336/ETY.

Voimassa 01-10-2004

ZWOLLENL

W. Kamphof

Laadunvalvontaosasto

Ferm FTHT-12V - 98/37/ETY, 73/23/ETY, 89/336/ETY. - 1

EXTRAVEILIGHEIDSWAARSCHUWING

VOOR HETLAADAPPARAAT

W. Kamphof Quality department

Ferm FTHT-12V - EXTRAVEILIGHEIDSWAARSCHUWING - 1

I Ceinture de support

I Coque de protection

CE DÉCLARATION DE CONFORMITÉ (F)

98/37/CEE, 73/23/CEE, 89/336/CEE,

du 01-10-2004

m = 311

2

CARATTERISTICHE

Fig. 1

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : Ferm

Model : FTHT-12V

Category : Hedge Trimmer