RNH3210SNH - Refrigerator DAEWOO - Free user manual and instructions

Brand	Daewoo
Model	RNH3210SNH (also RNH3210W1 H, RNH3210S1 H, RNH3210W1 HL, RNH3210S1 HL)
Product Type	Combi Fridge Freezer with No-Frost
Climate Class	SN, N, ST, T (ambient temperature 10°C to 43°C)
Control Interface	Electronic with Set button and LED indicators (Super mode, temperature levels)
Fridge Temperature Range	2°C, 3°C, 4°C, 6°C, 8°C selectable via Set button
Freezer Temperature Control	Slider located in fridge compartment for adjustment
Super Freeze Mode	Activates by pressing Set for over 3 seconds; automatically quits after 50 hours or manual deactivation
Memory Function	Automatically restores previous settings after power failure
Door Reversibility	Reversible; instructions and hardware (left hinge cover) included
Defrost System	No-Frost (automatic)
Refrigerant	R600a (isobutane), flammable
Levelling Feet	Adjustable front feet for leveling
Interior Light	Yes, special use lamp (not for domestic lighting)
Installation Clearance	Minimum 50 mm on sides and back; at least 100 mm above if below overhanging unit
Cleaning	Use lukewarm water and neutral soap; do not use abrasive cleaners or steam cleaners
Safety Features	Keep ventilation clear; do not damage refrigerant circuit; do not use mechanical defrosting devices
Electrical Requirements	Refer to rating plate; must be earthed; plug must be accessible after installation

Frequently Asked Questions - RNH3210SNH DAEWOO

How do I set the temperature in the fridge compartment?

Press the Set button (A) to cycle through the available temperatures: 2°C, 3°C, 4°C, 6°C, 8°C. The selected temperature indicator will light up. Note that in Super mode, the fridge temperature cannot be changed.

How do I activate Super Freeze mode?

Press and hold the Set button (A) for more than 3 seconds. The Super mode indicator will light up. The appliance will run at maximum freezing capacity for up to 50 hours, then automatically return to the previous setting. To deactivate manually, press and hold Set again for 3 seconds.

The freezer is not cold enough. What should I do?

First, check the temperature setting: ensure the freezer control slider (inside the fridge compartment) is set to a colder position. Also, avoid frequent or prolonged door openings, and ensure the appliance is not placed near a heat source. If the problem persists, refer to the Troubleshooting section in the manual.

Can I reverse the door of my Daewoo RNH3210SNH?

Yes, the door is reversible. You will need a straight and cross screwdriver, a spanner, and the supplied left door hinge cover. Detailed step-by-step instructions are provided in the manual. It is recommended to have two people for this task.

Why is there frost buildup on the door seal?

Frost on the door seal usually indicates the seal is not airtight. To fix this, gently warm the leaking sections of the seal with a hair dryer on a cool setting and carefully shape it by hand to sit correctly. Ensure the door is properly aligned and the appliance is level.

How should I clean the interior of the refrigerator?

Switch off the appliance and unplug it. Remove all food. Clean the interior and accessories with lukewarm water and a neutral soap. Rinse with fresh water and dry thoroughly. Do not use abrasive cleaners, steam cleaners, or sharp objects.

What does the Super mode indicator mean?

The Super mode indicator lights up when Super Freeze mode is active. This mode is used to freeze large amounts of fresh food quickly. It automatically deactivates after 50 hours or can be turned off manually by pressing the Set button for 3 seconds.

The appliance is making unusual noises. What can I do?

Check if the appliance is level by adjusting the front feet. Ensure it is not touching the wall or other objects. If a pipe or component on the back is touching another part, carefully bend it away. Some sounds (compressor, refrigerant circulation) are normal.

How do I store frozen food properly?

Wrap food in airtight packaging such as aluminium foil or polythene bags. Label each pack with the freezing date. Do not exceed the storage period recommended by the food manufacturer. Avoid opening the door frequently and keep it open as briefly as possible.

Can I freeze fresh food in this appliance?

Yes, the freezer compartment is suitable for freezing fresh food. Place fresh food in the bottom compartment. The maximum amount that can be frozen in 24 hours is indicated on the rating plate. During the freezing process (24 hours), do not add other food.

USER MANUAL RNH3210SNH DAEWOO

Combi Fridge Freezer No-Frost

Model: RNH3210W1 H

RNH3210S1 H

RNH3210W1 HL

RNH3210S1 HL

Content
1. Safety Information	Page 1~11
2. Overview	Page 12
3. Installation	Page 13~17
4.User interface	Page 18~19
5. Daily Use Page 20~22

In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.

For the safety of life and property keep the precautions of these user's instructions as the manufacturer is not responsible for damages caused by omission.

Children and vulnerable people safety

- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given super vision or instruction

concerning use of the appliance in a safe way and understand the hazards involved.

•Children should be supervised to ensure that they do not play with the appliance.
- Cleaning and user maintenance shall not be made by children unless they are aged from 8 years and above and supervised.
- Keep all packaging well away from children. There is risk of suffocation.

- If you are discarding the appliance pull the plug out of the socket, cut the connection cable (as close to the appliance as you can) and remove the door to prevent playing children to suffer electric shock or to close themselves into it.

- If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lack unusable before you discard the old appliance. This will prevent it from becoming a death trap for a child.

General safety

⚠ WARNING! Keep ventilation openings, in the

appliance enclosure or in the built-in structure, clear of obstruction.

⚠ WARNING! Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
⚠ WARNING! Do not damage the refrigerant circuit.
⚠ WARNING! Do not use other electrical appliances (such as ice cream makers) inside of refrigerating appliances, unless they are approved for this purpose by the manufacture.
⚠ WARNING! Do not touch the light bulb if it has been on for a long period of time because it could be very hot ₁₎

- Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

- The refrigerant isobutane (R600a) is c ontained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental

compatibility, which is nevertheless flammable.

- During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged. - avoid open flames and sources of ignition - thoroughly ventilate the room in which the appliance is situated

- It is dangerous to alter the specificat ions or modify this product in any way. Any damage to the cord may cause a short circuit, fire and/or electric shock.

- This appliance is intended to be used in household and similar applications such as - staff kitchen areas in shops, offices and other working environments; - farm houses and by clients in hotels, motels and other residential type environments; - bed and breakfast type environments; - catering and similar non-retail applications.

⚠ WARNING! Any electrical components (plug,

power cord, compressor and etc.) must be replaced by a certified service agent or qualified service personnel.

⚠ WARNING!The light bulb supplied with this appliance is a “special use lamp bulb” usable only with the appliance supplied. This “speciause lamp” is not usable for domestic lighting. ¹⁾

• Power cord must not be lengthened.

• Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a fire.

• Make sure that you can come to the mains plug of the appliance.

- Do not pull the mains cable.

- If the power plug socket is loose, do not insert the power plug. There is a risk of electric shock or fire.

- You must not operate the appliance without the lamp.

•This appliance is heavy. Care should be taken when moving it.
- Do not remove nor touch items from the freezer compartment if you hands are damp/wet, as this could cause skin abrasions or frost/freezer burns.
- Avoid prolonged exposure of the appliance to direct sunlight.

Daily use

• Do not put hot on the plastic parts in the appliance.
• Do not place food products directly against the rear wall.
• Frozen food must not be re-frozen once it has been thawed out. ¹⁾
• Store pre-packed frozen food in accordance with the frozen food manufactures instructions. ¹⁾
• Appliance's manufactures storage recommendations should be strictly adhered to. Refer to relevant instructions.
• Do not place carbonated of fizzy drinks in the

freezer compartment as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance. ¹⁾

- Ice lollies can cause frost burns if consumed straight from the appliance. ¹⁾

Care and cleaning

• Before maintenance, switch off the appliance and disconnect the mains plug from the mains socket.
• Do not clean the appliance with metal objects.
• Do not use sharp objects to remove frost from the appliance. Use a plastic scraper ¹⁾
• Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean the drain. If the drain is blocked, water will collect in te bottom of the appliance. ²⁾

Installation

Important! For electrical connection carefully follow the instructions given in specific

•1) If there is a freezer compartment.
- 2) If there is a fresh-food storage compartment.

paragraphs.

- Unpack the appliance and check if there are damages on it. Do not connect the appliance if it is damaged. Report possible damages immediately to the place you bought it. In that case retain packing.

- It is advisable to wait at least four hours before connecting the appliance to allow the oil to flow back in the compressor.

- Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve sufficient ventilation follow the instructions relevant to installation.

- Wherever possible the spacers of the product should be against a wall to avoid touching or catching warm parts (compressor, con-denser) to prevent possible burn.

•The appliance must not be located close to radiators or cookers.

• Make sure that the mains plug is accessible after the installation of the appliance.

Service

• Any electrical work required to do the servicing of the appliance should be carried out by a qualified electrician or competent person.
• This product must be serviced by an authorized Service Center, and only genuine spare parts must be used.

Energy saving

• Don't put hot food in the appliance;
• Don’t pack food close together as this prevents air circulating;
• Make sure food don’t touch the back of the compartment(s);
• If electricity goes off, don't open the door(s);
• Don't open the door(s) frequently;
• Don't keep the door(s) open for too long time;
• Don’t set the thermostat on exceeding cold temperatures;
• Some accessories, such as drawer s, can be removed to get larger storage volume and lower energy consumption.

Environment Protection

This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains flammable gases: the appliance shall be disposed according to the appliance regulations to obtain from your local authorities. Avoid damaging the cooling unit, especially the heat exchanger. The materials used on this appliance marked by the symbol are recyclable.

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could

otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.

Packaging materials

The materials with the symbol are recyclable. Dispose the packaging in a suitable collection containers to recycle it.

Disposal of the appliance

1. Disconnect the mains plug from the mains socket.
2. Cut off the mains cable and discard it.

Model:RNH3210W1 H
RNH3210S1 H
RNH3210W1 HL
RNH3210S1 HL
Note: Above picture is for reference only. Real appliance probably is different.

Space Requirement

• Select a location without direct exposure to sunlight;
• Select a location with enough space for the refrigerator doors to open easily;
• Select a location with level (or nearly level) flooring;
• Allow sufficient space to install the refrigerator on a flat surface;
• Allow clearance to the right, left, back and top when installing. This will help reduce power consumption and keep your energy bills lower.
• Keep at lest 50mm gap at two sides and back.

Positioning

Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:

Climate class	Ambient temperature
SN	+10°C to +32°C
N	+16°C to +32°C
ST	+16°C to +38°C
T	+16°C to +43°C

Location

The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Ensure that air can circulate freely around the back of the cabinet. To ensure best performance, if the appliance is positioned below an overhanging wall unit, the minimum distance between the top of the cabinet and the wall unit must be at least 100 mm. Ideally, however, the appliance should not be positioned below overhanging wall units. Accurate leveling is ensured by one or more adjustable feet at the base of the cabinet.

Warning! It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation.

Electrical connection

Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply. The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician.

The manufacturer declines all responsibility if the above safety precautions are not observed.

This appliance complies with the E.E.C. Directives.

Door Reversibility

Before reversing the door, please be prepared below tools and material: straight screwdriver, cross screwdriver, spanner and the components included in the poly bag:

Left Door Hinge Cover x 1

1. Unscrew top hinge cover and then unscrew the top hinge .

Then lift upper door and place it on a soft pad to avoid scratch and damage.

Technical line drawing of a screwdriver inserted into a mechanical clamp (no text or symbols)

Technical line drawing of a mechanical assembly with a screwdriver inserted, no text or symbols present

1. Remove the top left screw cover.

Technical line drawing of a screwdriver inserted into a bracket (no text or symbols)

Technical line drawing of a mechanical assembly with a bracket and mounting bracket (no text or symbols)

1. Take off the upper door, take out the screw from the middle hinge by cross screwdriver, then take off the lower door.

Technical line drawing of a mechanical clamp or bracket (no text or symbols)

1. Laying down the refrigerator, take out the adjusting feet as below, then take off the lower hinge by cross screwdriver.

Technical line drawing of a mechanical assembly with an inset close-up showing a gear mechanism (no text or symbols)

1. Adjusting the hinge core position of the lower hinge and upper hinge to opposite position

Technical illustration of a mechanical clamp or bracket assembly, showing a disassembly process (no text or symbols present)

Diagram showing a mechanical clamp or wrench being adjusted, with no text or symbols present.

1. Install the lower hinge under to the refrigerator like below, screwing in the adjusting feet, make sure the position in horizon.

Technical line drawing of a mechanical assembly with an inset close-up showing a component detail (no text or symbols)

Installation

1. Install the lower door, adjust and fix the middle hinge onto the cabinet.

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

1. Place the upper door back on. Ensure the door is aligned horizontally and vertically so that the seal are closed on all sides before finally tightening the top hinge. Then inert the top hinge and screw it to the top of unit and then fix hinge cover (in accessory bag) by screw.

Technical line drawing of a screwdriver inserted into a bracket with mounting holes (no text or symbols)

Technical line drawing of a screwdriver inserted into a clamp bracket (no text or symbols)

1. Fix the screw cover.

Technical line drawing of a screwdriver inserted into a workbench (no text or symbols)

Space Requirement

• Keep enough space of door open.
• Keep at least 50mm gap at two sides.

Levelling the unit

To do this adjust the two levelling feet at front of the unit.

If the unit is not level, the doors and magnetic seal alignments will not be covered properly.

1. Setting Panel:

2. Button

A. Set button

Pressthisbuttontoselectrunningtemperatureand"Super" mode.

3. Indicators

1) Super mode indicator: the light is on when Super mode is selected.
2) Setting Temperature indicators of fridge compartment. The lighted indicator means related temperature is selected.

4. Super mode

Activate Super mode

When you plan to freeze food in a short time, you can select Super mode. Keep pressing Set button (A) for over 3 seconds, Super mode will be activated. Indicator under Super will be lighted.

At the same time, the temperature indicator of the fridge compartment will not change. Quit from Super mode

- Press Set button (A) for over 3 seconds

- Or the appliance will automatically restore to original setting when Super mode has running for more than 50 hours.

In Super mode, the temperature setting offridge compartment cannot be changed.

5. Temperature setting of the Fridge Compartment

In normal using mode (not Super mode), press Set button (A) to adjust setting temperature of fridge compartment in a cycle of "2°C, 3°C, 4°C, 6°C, 8°C".

Useful hints:

Please follow the below table to choose setting temperature of fridge.

Environment Temperatureto	Recommended Temperature
Summer (>32°C)	4°C, 6°C, 8°C
Normal	4°C
Winter(<13°C)	2°C, 3°C, 4°C

6. Memory function after Power off

The appliance will automatically re-start to run in previous mode after a power failure.

7. Temperature Control of the Freezer Compartment

The freezer temperature setting slider:

FREEZER CONTROL

• This slider in fridge compartment is used to adjust temperature of freezer compartment.
• Slider is positioned toward , the temperature in freezer compartment will be higher. Contrarily

the temperature in freezer compartment will be lower if the slider is moved toward

• Middle position of slider is advised position for normal using.
• To get lowest temperature in freezer compartment, you can select temperature setting of fridge

compartment at "2" and position the slider at

First use

Cleaning the Interior

Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand new product, then dry thoroughly.

Important! Do not use detergents or abrasive powders, as these will damage the finish.

Daily use

Freezing fresh food

• The freezer compartment is suitable for freezing fresh food and storing frozen and deep-frozen food for a long time.
• Place the fresh food to be frozen in the bottom compartment.
• The maximum amount of food that can be frozen in 24 hours is specified on the rating plate.
• The freezing process lasts 24 hours: during this period do not add other food to be frozen.

Storing frozen food

When first starting-up or after a period out of use. Before putting the product in the compartment let the appliance run at least 2 hours on the higher settings.

Important! In the event of accidental defrosting, for example the power has been off for longer than the value shown in the technical characteristics chart under "rising time", the defrosted food must be consumed quickly or cooked immediately and then re-frozen (after cooked).

Thawing

Deep-frozen or frozen food, prior to be used, can be thawed in the freezer compartment or at room temperature, depending on the time available for this operation.

Small pieces may even be cooked still frozen, directly from the freezer. In this case, cooking will take longer.

Helpful hints and tips

Hints for freezing

To help you make the most of the freezing process, here are some important hints:

• the maximum quantity of food which can be frozen in 24 hrs. is shown on the rating plate;
• the freezing process takes 24 hours. No further food to be frozen should be added during this period;
• only freeze top quality, fresh and thoroughly cleaned, foodstuffs;
• prepare food in small portions to enable it to be rapidly and completely frozen and to make it possible subsequently to thaw only the quantity required;
• wrap up the food in aluminium foil or polythene and make sure that the packages are airtight;
• do not allow fresh, unfrozen food to touch food which is already frozen, thus avoiding a rise in temperature of the latter;
• lean foods store better and longer than fatty ones; salt reduces the storage life of food;
• water ices, if consumed immediately after removal from the freezer compartment, can possibly cause the skin to be freeze burnt;
• it is advisable to show the freezing in date on each individual pack to enable you removal from the freezer compartment, can possibly cause the skin to be freeze burnt;
• it is advisable to show the freezing in date on each individual pack to enable you to keep tab of the storage time.

Hints for storage of frozen food

To obtain the best performance from this appliance, you should:

make sure that the commercially frozen foodstuffs were adequately stored by the retailer;

be sure that frozen foodstuffs are transferred from the food store to the freezer in the shortest possible time;

not open the door frequently or leave it open longer than absolutely necessary.

Once defrosted, food deteriorates rapidly and cannot be refrozen.

Do not exceed the storage period indicated by the food manufacture.

Hints for fresh food refrigeration

To obtain the best performance:

- Do not store warm food or evaporating liquids in the refrigerator

- Do cover or wrap the food, particularly if it has a strong flavour

Hints for refrigeration

Useful hints:

• Make (all types): wrap in polythene bags and place on the glass shelves above the vegetable drawer.
- For safety, store in this way only one or two days at the most.
- Cooked foods, cold dishes, etc....: these should be covered and may be placed on any shelf.
- Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s) provided.
- butter and cheese: these should be placed in special airtight containers or wrapped in aluminum foil or polythene bags to exclude as much air as possible.
- Milk bottle: these should have a cap and should be stored in the balconies on the door.
- Bananas, potatoes, onions and garlic, if not packed, must not be kept in the fridge.

Cleaning

For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly.

Caution! The appliance may not be connected to the mains during cleaning. Danger of electrical shock! Before cleaning switch the appliance off and remove the plug from the mains, or switch off or turn out the circuit breaker or fuse. Never clean the appliance with a steam cleaner. Moisture could accumulate in electrical components, danger of electrical shock! Hot vapors can lead to the damage of plastic parts. The appliance must be dry before it is placed back into service.

Important! Ethereal oils and organic solvents can attack plastic parts, e.g. lemon juice or the juice form orange peel, butyric acid, cleanser that contain acetic acid.

• Do not allow such substances to come into contact the appliance parts.
• Do not use any abrasive cleaners
• Remove the food from the freezer. Store them in a cool place, well covered.
• Switch the appliance off and remove the plug from the mains, or switch off or turn out the circuit breaker of fuse.
• Clean the appliance and the interior accessories with a cloth and lukewarm water. After cleaning wipe with fresh water and rub dry.
  •After everything is dry place appliance back into service.

Troubleshooting

Caution! Before troubleshooting, disconnect the power supply. Only a qualified electrician of competent person must do the troubleshooting that is not in this manual.

Important! There are some sounds during normal use (compressor, refrigerant circulation).

Problem	Possible cause	Solution
Appliance dose not work	Mains plug is not plugged in or is loose	Insert mains plug.
	Fuse has blown or is defective	Check fuse, replace if necessary.
	Socket is defective	Mains malfunctions are to be corrected by an electrician.
Appliance freezes or cools too much	Temperature is set too cold or the appliance runs at Super modes.	Turn the temperature regulator to a warmer setting temporarily.
The food is not frozen enough.	Temperature is not properly adjusted.	Please look in the initial Temperature Setting section.
	Door was open for an extended period.	Open the door only as long as necessary.
	A large quantity of warm food was placed in the appliance within the last 24 hours.	Turn the temperature regulation to a colder setting temporarily.
	The appliance is near a heat source.	Please look in the installation location section.
Heavy build up of frost on the door seal.	Door seal is not air tight.	Carefully warm the leaking sections of the door seal with a hair dryer (on a cool setting). At the same time shape the warmed door seal by hand such that it sits correctly.
Unusual noises	Appliance is not level.	Re-adjust the feet.
	The appliance is touching the wall or other objects.	Move the appliance slightly.
	A component, e.g. a pipe, on the rear of the appliance is touching another part of the appliance or the wall.	If necessary, carefully bend the component out of the way.

If the malfunction shows again, contact the Service Center.

These data are necessary to help you quickly and correctly. Write the necessary data here, refer to the rating plate.

Руководство

пользователя

Холодильник

Εισμα:RNH3210W1 H

RNH3210S1 H

RNH3210W1 HL

RNH3210S1 HL

Technical line drawing of a screwdriver inserted into a clamp bracket (no text or symbols)

Technical line drawing of a mechanical assembly with a screwdriver and two components (no text or symbols)

Technical line drawing of a screwdriver inserted into a bracket (no text or symbols)

Technical line drawing of a mechanical assembly with a bracket and mounting base (no text or symbols)

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Technical line drawing of a mechanical assembly with an inset close-up showing a gear mechanism (no text or symbols)

Technical illustration of a mechanical clamp or bracket assembly, showing a disassembly process (no text or symbols present)

Technical line drawing of a mechanical clamp or wrench tool with a downward arrow indicating process (no text or symbols present)

Technical line drawing of a mechanical assembly with an inset close-up showing a component detail (no text or symbols)

Установка

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Technical line drawing of a screwdriver inserted into a bracket with mounting holes (no text or symbols)

Technical line drawing of a screwdriver inserted into a mechanical clamp (no text or symbols)

Technical line drawing of a screwdriver inserted into a bracket (no text or symbols)

Установка

Pure geometric diagram with lines and shapes, no text or symbols present

Technical line drawing of a screwdriver inserted into a clamp bracket (no text or symbols)

Technical line drawing of a mechanical assembly with a screwdriver inserted and a bracket (no text or symbols)

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Technical line drawing of a mechanical assembly with a bracket and mounting base (no text or symbols)

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Technical line drawing of a mechanical assembly with an inset close-up showing a gear mechanism (no text or symbols)

Technical illustration of a mechanical clamp or bracket assembly, showing disassembly from a housing component to a handle (no text or symbols present)

Technical line drawing of a mechanical clamp or lever mechanism with a downward arrow indicating motion (no text or symbols present)

Technical diagram showing a mechanical assembly with an inset close-up of a component detail (no text or symbols)

OPHATY

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Technical line drawing of a screwdriver inserted into a bracket with mounting holes (no text or symbols)

Technical line drawing of a screwdriver inserted into a bracket (no text or symbols)

Technical line drawing of a mechanical clamp or bracket assembly (no text or symbols)

Какетті аумак

Pure geometric diagram with lines and shapes, no text or symbols present

Курылғыны теңестіру

1. Орнату Панелі:

graph TD
    A["1 Super"] --> B["2"]
    B --> C["3"]
    C --> D["4"]
    D --> E["6"]
    E --> F["8 °C"]
    G["2"] --> H["Set"]
    I["A"] --> H
    H --> J["Super/3s"]

2. Түймешік