KSTAW05CE - Air-conditioner Keystone - Free user manual and instructions

Type de produit	Window Air Conditioner
Modèle	KSTAW05CE
Marque	Keystone
Capacité de refroidissement	5,000 BTU
Zone de couverture	Up to 150 sq. ft.
Dimensions (L x H x P)	15.5 x 12 x 12 inches
Poids net	40 lbs
Alimentation électrique	115V, 60Hz, 4.5A
Consommation électrique	460W (cooling)
Modes de fonctionnement	Cool, Fan only, Energy Saver
Vitesses de ventilateur	2 (Low/High)
Thermostat réglable	Yes, mechanical dial
Direction de l'air	Adjustable horizontal louvers
Filtre à air	Washable mesh filter
Niveau sonore	~52 dB (low), ~56 dB (high)
Certifications	Energy Star, UL listed
Entretien	Clean filter monthly, coil annually
Installation	Window mount kit included
Sécurité	Anti-theft bracket, safety lock
Accessoires inclus	Remote control, installation kit
Garantie	1 year parts and labor

Frequently Asked Questions - KSTAW05CE Keystone

What is the BTU rating of the Keystone KSTAW05CE air conditioner?

The Keystone KSTAW05CE is a 5,000 BTU window air conditioner, suitable for cooling rooms up to 150 sq. ft.

What are the dimensions and weight of this unit?

The unit measures approximately 15.5 x 12 x 12 inches and weighs about 40 lbs.

How do I install the KSTAW05CE in a window?

Place the unit in a double-hung window, secure with the included mounting brackets, and seal gaps with foam weatherstripping. Ensure the window is fully closed and locked.

Does the KSTAW05CE come with a remote control?

Yes, a remote control is included for convenient operation from across the room.

How often should I clean the air filter?

Clean the washable filter every month during heavy use. Remove the filter, vacuum or rinse with water, dry completely, and reinstall.

Can I use an extension cord with this air conditioner?

No, do not use an extension cord or power strip. Plug directly into a grounded 115V outlet to avoid fire hazard.

What are the operating modes available?

The unit offers Cool, Fan Only, and Energy Saver modes. Energy Saver mode cycles the fan with the compressor to save power.

How loud is the KSTAW05CE?

Noise level ranges from approximately 52 dB on low fan speed to 56 dB on high, comparable to a quiet conversation.

Is the KSTAW05CE Energy Star certified?

Yes, it is Energy Star certified for energy efficiency, helping reduce electricity costs.

What is the warranty coverage?

Keystone provides a 1-year limited warranty on parts and labor. Contact customer service for support.

USER MANUAL KSTAW05CE Keystone

1 PREPARE THE WINDOW

Lower sash must open sufficiently to allow a clear vertical opening of 13 inches (330mm). Side louvers and the rear of the AC must have clear air space to allow enough airflow through the condenser, for heat removal. The rear of the unit must be outdoors, not inside a building or garage.

Mounting Hardware 3/4" (or 2") Lock Frame Sash Lock Window sash Screws (7) (2) (1) seal fo am (1) (1)

2 PREPARE AIR CONDITIONER

A: Remove the air conditioner from the carton and place on a flat surface.

B: Remove top rail from the rear of the packaging material as shown in Fig. A.

Top Rail Hardware or 3/8" Screws (4) Top Rail (1)

Fig.A Top Rail Packaging

C: Align the hole in the top rail with those in tr of the unit as shown in Fig.B

Fi g.B

D: Secure the top rail to the unit with the 3/8 S as shown in Fig.C.

Technical line drawing of an air conditioner unit with mounting screws and ventilation slots (no text or symbols)

NOTE: For safety reasons, all four(4) screws MUST be securely fastened.

3 INSTALL THE ACCORDION PANELS

NOTE: Top rail and Sliding Panels at each side are offset to provide the proper pitch to the rear of (5/1) This is necessary for proper condensed water utilization and drainage. If you are not using the Panels for any reason, this pitch to the rear must be maintained.

Simple line drawing of a vertical corrugated structure with an arrow pointing left (no text or symbols)

A. Place unit on floor, a bench or a table. Hold the Accord ion Panel in one hand and gently pull back the center to free the open end. See Fig.1

Fig.1

B. Slide the free end " " section of the panel into the cabinet as shown in Fig. 2. Slide the down. Be sure to leave enough space to slip top and bottom of the frame into the rails on cabinet.

" "s ection 1

Fig.2

C. Once the panel has been installed on the the cabinet, make sure it sits securely inside frame channel by making slight adjustments. Slide the top and bottom ends of the frame top and bottom rails of the cabinet. Fig.3.

Top Rail Bottom Rail

Fig.3

D. Slide the panel all the way in and repeat other side.

Fig.4 Top left Top Rail Top right Bottom Rail

INOSTE:m window blocks AC, see Fig. 11.

SECURE THE ACCORDION PANELS

tAeKeep a firm grip on the air conditioner, carefully place the unit into the window opening so the bott of the air conditioner frame is against the window sill (Fig.5). Carefully close the window behind the to rail of the unit. Measure from the cabinet edge

INSIDE Wooden Windows OUTSIDE About 5/8 to 3/4

Fig.5

NOT E: Check that air conditioner is tilted back a 5/8" to 3/4 (tilted about 3° to 4 downward to the outside side of after proper installation, condensate should not drain from the overflow drain hole during normaluse, correct the slope otherwise.

B. Extend the side panels out against the window frame (Fig.6).

(Fig.6). window frame

Fig.6

INSTALL SUPPORT BRACKET

on AURace the frame lock between the frame extensions and the window sill as shown(Fig.7). Drive 3 / 4 (19mm) or 2" (12.7mm) locking screws through the frame lock and into the sill.

NOTE: To prevent window sill from s plitting, drill 1 / 8" (3mm) pilot holes before driving screws.

Line drawing of a hand holding a tool near a window frame, with an inset showing a bracket detail (no text or symbols)

B. Drive 3142" (192m7m)m)pr locking

screws through frame holes into window sash

(Fig.8)

Technical line drawing of a cabinet or enclosure with ventilation ducts and control panel (no text or symbols)

Fig.8

C. To secure lower sash in place, attach right sash lock with 3/4" (19mm) /20r (12.30rev) as shown(Fig.9).

Line drawing of a hand holding a metal bracket with a pull rod (no text or symbols)

Fig.9

D.Cut Windlovinsealshit sial theam

space between the upper and lower sashes (Fig.10).

FOAM SEAL Fig.10

If AC is Blocked by Storm Window

Add wood as shown in Fig.11, or remove storm window before air conditioner is installed.

If Storm Window Frame must remain, be sure the drain holes or slots are not caulked or painted shi Accumulated Rain Water or Condensation must be allowed to drain out.

Removing AC From Window

◆Turn AC off, and disconnect power cord.
◆ Remove sash seal from between windows, and unscrew safety sash lock.
◆ Remove screws installed through frame and frame-lock.
◆ Close (slide) side panels into frame.
- Keeping a firm grip on air conditioner, raise sash and carefully remove.
◆ Be carefully not to spill any rem aining water with lifting unit from window. Store parts WITH air conditioner.

SASH Storm window frame or other obstruction. 1-1/2"min (38 mm) Board thickness as required, for pr oper pitch to rea r, along entire sill. Fasten with nails o r screw s.

Fig.11