TED Pack LC BS13 - Lighting Showtec - Free user manual and instructions
Find the device manual for free TED Pack LC BS13 Showtec in PDF.
Pick your language and provide your email: we'll send you a specifically translated version.
| Product Type | LED Bar |
| Dimensions (L x W x H) | 1000 x 100 x 150 mm |
| Weight | 4.5 kg |
| Power Supply | AC 100-240V, 50/60Hz |
| Power Consumption | 120 W max |
| Light Source | 60 x 1W RGB LEDs (3-in-1) |
| Beam Angle | 15° (linear) |
| Control Protocol | DMX-512 |
| DMX Channels | 5 / 10 / 14 selectable |
| Operating Modes | Standalone, Master/Slave, Sound-Active, Auto |
| Display | 4-digit LED display |
| Connectors | 3-pin XLR in/out, IEC power in |
| IP Rating | IP20 (indoor use only) |
| Cooling | Fan cooled |
| Housing Material | Metal |
| Mounting | Floor standing or truss mount (brackets included) |
| Safety Certifications | CE, RoHS |
| Maintenance & Cleaning | Use a dry, soft cloth; avoid solvents; keep ventilation clear |
| Spare Parts & Repairability | Replaceable fuse, power supply, LED modules; service by qualified technician |
| General Information | User manual included; suitable for stage, events, club lighting |
Frequently Asked Questions - TED Pack LC BS13 Showtec
How do I set the DMX address on the TED Pack LC BS13?
Press the MENU button until the DMX address is displayed, then use the UP/DOWN buttons to set the desired address (001-512). Press ENTER to confirm.
Can I connect multiple TED Pack LC BS13 units together?
Yes, you can link multiple units via DMX daisy chain using XLR cables. Set the first unit as Master and the others as Slave (or assign unique DMX addresses).
What is the beam angle of this fixture?
The beam angle is 15° linear, providing a tight beam of light suitable for accent or stage lighting.
Is the TED Pack LC BS13 suitable for outdoor use?
No, it has an IP20 rating and is designed for indoor use only. Avoid exposure to rain, moisture, or extreme temperatures.
How do I reset the fixture to factory defaults?
Press MENU until 'dFLT' appears, then press ENTER. The display will show 'LOAD' and reset to default settings.
What type of DMX cable should I use?
Use standard 3-pin XLR microphone cables designed for DMX. Ensure the cable is 120 ohm impedance for proper signal transmission.
How do I replace the fuse?
Disconnect power. Open the fuse holder near the power input using a flathead screwdriver. Replace with same type: F1A 250V. Close securely.
How should I clean the fixture?
Disconnect power. Use a dry, lint-free cloth to wipe the housing and lens. Do not use water, solvents, or abrasive cleaners.
What power cord does the TED Pack LC BS13 require?
It uses a standard IEC C14 power cord (male to C13). The input voltage is 100-240V AC, so it can be used worldwide with the appropriate plug.
Can I mount the fixture on a truss?
Yes, it comes with mounting brackets. Use safety cables and ensure the truss can support the weight (4.5 kg). Tighten all knobs securely.
User questions about TED Pack LC BS13 Showtec
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
No questions yet. Be the first to ask one.
Download the instructions for your Lighting in PDF format for free! Find your manual TED Pack LC BS13 - Showtec and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. TED Pack LC BS13 by Showtec.