58G548 - Drill Graphite - Free user manual and instructions

Product Type	Corded Drill
Brand	Graphite
Model	58G548
Power Supply	AC 230V, 50Hz
Power Consumption	600 W
No-Load Speed	0 - 2800 RPM
Chuck Type	Keyless, 13 mm
Max Drilling Capacity (Steel)	13 mm
Max Drilling Capacity (Wood)	30 mm
Weight	1.5 kg
Dimensions (L x W x H)	260 x 65 x 180 mm
Main Functions	Drilling, screwdriving
Speed Control	Variable speed trigger
Forward/Reverse	Yes
Maintenance	Regular cleaning, carbon brush replacement
Cleaning	Wipe with dry cloth; avoid solvents
Safety Features	Double insulation, lock-off switch
Spare Parts Availability	Carbon brushes, chuck, switch
Repairability	User-replaceable parts; service center support
Additional Features	Ergonomic handle, LED light

Frequently Asked Questions - 58G548 Graphite

How do I change the drill bit on the Graphite 58G548?

Turn the chuck counterclockwise to open it, insert the bit, and tighten by turning clockwise. The keyless chuck allows easy bit changes without a key.

What is the power consumption of this drill?

The Graphite 58G548 has a 600 W motor, suitable for most DIY tasks.

Can I use the drill for screwdriving?

Yes, it features a variable speed trigger and forward/reverse switch, making it suitable for screwdriving as well as drilling.

What is the maximum drilling capacity in steel?

The maximum drilling capacity in steel is 13 mm. For wood, it can drill up to 30 mm.

How do I adjust the speed?

The speed is controlled by the variable speed trigger. Pressing the trigger lightly gives low speed; pressing fully gives higher speed.

Is the drill double insulated?

Yes, the Graphite 58G548 features double insulation for enhanced safety, so no grounding is required.

How do I replace the carbon brushes?

Unscrew the brush caps on the motor housing, remove worn brushes, and insert new ones. Ensure they are identical replacement parts.

What maintenance does the drill need?

Regularly clean the ventilation slots with a dry cloth and check the carbon brushes for wear. Keep the chuck clean for optimal grip.

Does the drill have an LED light?

Yes, it is equipped with an LED work light above the trigger to illuminate the work area.

Where can I find the user manual?

The manual is available for free download on the notice-facile.com website in multiple languages.

USER MANUAL 58G548 Graphite

INSTRUKCJA ORYGINALNA (OBSŁUGI)

MŁOTOWIERTARKA

58G548

UWAGA: PRZED PRZYSTĄPIENIEM DO UŻYTKOWANIA ELEKTRONARZĘDZIA NALEŻY UWAŻNIE PRZECZYTAĆ NINIEJSZĄ INSTRUKCJĘ I ZACHOWAĆ JĄ DO DALSZEGO WYKORZYSTANIA.

SZCZEGÓŁOWE PRZEPISY BEZPIECZEŃSTWA

/Declaration of Conformity/

/ Rotary hammer drill /

/Vesőkalapacs/

Model

/Model./

/Modell/

58G548

Numer seryjny

/Serial number/

/Sorszám/

00001 ÷ 99999

/The above listed product is in conformity with the following UE Directives:/

/Machinery Directive 2006/42/EC/

/ 2006/42/EK Gépek /

/EMC Directive 2004/108/EC/

/and fulfils requirements of the following Standards:/

/Last two figures of CE marking year:/

/Name and address of the person who established in the Community and authorized to compile the technical file/

/GRUPA TOPEX Quality Agent /

CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.

DETAILED SAFETY REGULATIONS

• Use ear protection when operating the rotary hammer drill. Noise hazards may cause hearing loss.
• Use protection measures for respiratory system when operating the rotary hammer drill. Dust hazards may cause respiratory system illness.
• Use dust extraction systems whenever required by the nature of the work performed.
• Use additional handles supplied with the tool. Loss of control may cause operator personal injury.

CAUTION! This device is designed to operate indoors.

The design is assumed to be safe, protection measures and additional safety systems are used, nevertheless there is always a small risk of operational injuries.

CONSTRUCTION AND USE

Rotary hammer drill is a hand-operated power tool with insulation class II. The tool is driven by single-phase commutator motor with rotational speed reduced with gear transmission. Rotary hammer drill can be used for drilling holes in working modes: with impact, rotation only, digging channels or surface processing of materials such as concrete, stone, brick etc. Range of use covers repair and building works, woodworking and any work from the scope of individual, amateur activities (tinkering).

Use the power tool according to the manufacturer's instructions only.

DESCRIPTION OF DRAWING PAGES

Below enumeration refers to the device elements depicted on the drawing pages of this manual.

SDS Plus chuck1.

Fixing sleeve2.

Depth gauge rod3.

Operation mode switch4.

1. Direction selector switch
2. Switch
3. Voltage indicator lamp
4. Carbon brush cover

5. Additional handle

6. Fixing lever for depth gauge rod

* Differences may appear between the product and drawing.

MEANING OF SYMBOLS

CAUTION

WARNING

ASSEMBLY/SETTINGS

INFORMATION

EQUIPMENT AND ACCESSORIES

1. Drills - 1 pce 4. Drill chuck + key - 1 pce
2. Depth gauge rod - 1 pce 5. Chuck adapter - 1 pce
3. Additional handle - 1 pce 6. Transport case - 1 pce

INSTALLATION OF ADDITIONAL HANDLE

Due to safety reasons always use additional handle when operating the rotary hammer drill.

• Loosen the wheel lock that locks collar of the additional handle (9) by turning it left.
• Slide collar of the additional handle onto the rotary hammer drill body and set it to the most comfortable position.

Tighten the wheel lock for additional handle to fix it securely. ●

Additional handle can be set in any position on the rotary hammer drill circumference.

INSTALLATION OF DEPTH GAUGE ROD

Depth gauge rod is used to limit the depth of drill penetration of material.

- Press in the fixing lever for depth gauge rod (10).

- Slide depth gauge rod (3) into the hole in the additional handle collar. Set desired drill depth.

- Release the fixing lever for depth gauge rod (10) to lock.

INSTALLATION AND REPLACEMENT OF WORKING TOOLS

Rotary hammer drill is designed to operate with working tools with SDS Plus shanks. Clean the rotary hammer drill chuck and working tool before installation. Apply thin layer of grease onto shank of the working tool.

Disconnect the power tool from power supply.

Rotary hammer drill features clic-clic system (which does not require to pull off the fixing sleeve (2) when installing a working tool).

Put the rotary hammer against stable surface. ●

- Insert working tool shank into chuck (1) and slide it to mechanical stop (it may be necessary to turn the working tool so it can reach appropriate position) (fig. A).

- Working tool is properly seated if it cannot be removed without pulling off the fixing sleeve.

- If the sleeve (2) does not return to its default position, remove the working tool and repeat the whole operation.

Working tool is properly seated if it cannot be removed without pulling off the fixing sleeve. High efficiency of the rotary hammer drill operation can be achieved by using sharp and undamaged working tools.

DEINSTALLATION OF WORKING TOOL

Just after the operation is finished, the working tool may be hot. Avoid direct contact and use appropriate protective gloves. Clean the working tool after removal.

- Pull the fixing sleeve (2) to the back and hold.

- Remove the working tool with your second hand by pulling it to the front (fig. A).

OVERLOAD CLUTCH

Rotary hammer drill is equipped with internally set overload clutch. Spindle of the rotary hammer drill stops immediately after working tool jams, which could overload the power tool.

SWITCHING ON / SWITCHING OFF

The mains voltage must match the voltage on the label of the rotary hammer drill.

Switching on – press the switch button (6) and hold in this position (fig. B). Switching off – release pressure on the switch (6).

Rotational speed of the spindle is controlled with pressure on the switch button (6).

The rotary hammer drill features 4-position operation mode switch (4) and allows to drill without impact, with impact or chiselling.
Press the switch lock button 'a' prior to change of position of the operation mode switch (4) (fig. C).

- Pos 0 = position for setting chisel in desired position (chisel symbol)

Pos 1 ●= regular drilling/screwing (symbol of a drill)

Pos 2 ● = impact drilling (symbol of a drill and a hammer)

Pos 3 ●= chiselling (symbol of a chisel and a hammer)

Do not try to change position of the working mode switch when motor of the rotary hammer drill is operating. Such action may cause serious damage of the rotary hammer drill or injury of the user.
i Impact drilling and chiselling requires to slightly press the rotary hammer drill. Too great pressure would cause unnecessary, excessive load of the motor. Check technical condition of the working tools regularly. Sharpen or replace working tools when necessary.

LEFT - RIGHT DIRECTION OF ROTATION

Choose direction of rotary hammer drill spindle rotation with the direction selector switch (5). Clockwise rotation – set the direction selector switch (5) to the extreme left position (fig. B). Counter-clockwise rotation – set the direction selector switch (5) to the extreme right position.

* The possibility is reserved that in certain cases position of the direction selector switch relating to rotation direction of spindle may be different than specified. Please refer to graphic signs placed on the switch or tool body.

Do not change direction of rotation when the spindle of the rotary hammer drill is rotating. Check if the position of the selector switch is correct before starting the tool. Do not use left direction of rotation when impact function is on.

VOLTAGE INDICATOR LAMP

When the rotary hammer drill is connected to power supply socket, the voltage indicator lamp lights up.

DRILLING HOLES

• When drilling a hole with large diameter, it is recommended to drill smaller hole and then ream it to desired diameter. It prevents overloading the rotary hammer drill.
• When drilling deep holes drill gradually to smaller depths, then slide the drill out of the hole to remove chips and dust.
• If a drill jam occurs during drilling, the overload clutch will activate. Turn off the rotary hammer drill immediately to prevent its damage. Remove jammed drill from the hole.
• Keep the rotary hammer drill in the axis of the hole. Keeping the drill perpendicular to the surface of the processed material ensures the most effective operation. If a drill is not kept perpendicular to the surface during operation, it may get jammed or broken in the hole, and even injure the user.

Long lasting drilling at low rotational speed of the spindle may cause motor overheating. Provide periodic breaks during operation or let the tool operate at maximum speed with no load for approximately 3 minutes. Do not cover holes for motor ventilation in the rotary hammer drill body.

DRILLING WITHOUT IMPACT

Materials like steel, wood and plastics can be drilled with rotary hammer drill with the use of three jaw drill chuck with intermediate adapter. Mount together three jaw drill chuck and intermediate adapter and then place it in the rotary hammer drill chuck (proceed like with SDS Plus drills) (fig. D).
Do not use three jaw drill chuck when the rotary hammer drill is set to impact drilling. This drill chuck is designed for regular drilling only (in wood or steel). Use drills of high speed steel or carbon steels (only for wood and wood-like materials).

IMPACT DRILLING

• Set operation mode switch (4) in position for impact drilling.
• Insert appropriate SDS Plus drill into the chuck (1).
• To get the best results use high quality drills with solid carbide inserts.

GRAPHITE

Press the drill against processed material. ●

• Switch on the rotary hammer drill by pressing the switch button (6), the power tool mechanism should operate smoothly and the working tool should not bounce on the processed material surface.
• Increase speed when necessary by pressing harder on the switch button (6).

Disconnect the tool from power supply before starting any regulation, maintenance or repair.

• Soft brush or compressed air are best for cleaning the rotary hammer drill.
• Do not clean the rotary hammer drill with water or chemical cleaning agents.

Store the rotary hammer drill in a dry place, beyond reach of children. ●

Keep ventilation holes of the motor unobstructed.

- In case of excessive commutator sparking have the technical condition of carbon brushes of the motor checked by a qualified person.

Entrust replacement of power cord and other repairs only to authorized service workshop.

REPLACEMENT OF CARBON BRUSHES

Replace immediately worn out (shorter than 5 mm), burnt or cracked motor carbon brushes. Always replace both carbon brushes at a time.

• Unscrew carbon brush covers (8) (fig. E).
  Remove used carbon brushes.
• Remove any carbon dust with compressed air.
• Insert new carbon brushes (carbon brushes should easily move into brush holders) (fig. F).
  • Fix carbon brush covers (8).

After the carbon brushes are replaced, start the rotary hammer drill with no load and wait until the carbon brushes fit to the motor commutator. Entrust replacement of carbon brushes only to a qualified person. Only original parts should be used.

All faults should be repaired by service workshop authorized by the manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS

Rotary Hammer Drill
Parameter		Value
Supply voltage		230 V AC
Current frequency		50 Hz
Rated power		950 W
Idle rotational speed		0 – 1000 rpm
Impact rate		0 – 4800 spm
Impact energy		2.4 J
Working tool shank		SDS Plus
Maximum drilling diameter	concrete	26 mm
	steel	13 mm
	wood	40 mm
Protection class		II
Weight (w/o accessories)		4.5 kg
Year of production		2014

Sound pressure Lp_A=91.3\ dB(A) K=3 dB(A)

Sound power: Lw_A=102.3\ dB(A) K=3 dB(A)

Vibration acceleration (drilling) a_h = 18.595 m/s² K = 1,5 m/s²

Vibration acceleration (chiselling) a_h=15.247\ m/s² K=1,5 m/ s²

ENVIRONMENT PROTECTION

Do not dispose of electrically powered products with household wastes, they should be utilized in proper plants. Obtain information on wastes utilization from your seller or local authorities. Used up electric and electronic equipment contains substances active in natural environment. Unrecycled equipment constitutes a potential risk for environment and human health.

* Right to introduce changes is reserved.

"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with seat in Warsaw at ul. Pograniczna 2/4 (hereinafter Grupa Topex) informs, that all copyrights to this instruction (hereinafter Instruction), including, but not limited to, text, photographies, schemes, drawings and layout of the instruction, belong to Grupa Topex exclusively and are protected by laws accordingly to Copyright and Related Rights Act of 4 February 2004 (ustawa o prawie autorskim i prawach pokrewnych, Dz. U. 2006 No 90 item 631 with later amendments). Copying, processing, publishing, modifications for commercial purposes of the entire Instruction or its parts without written permission of Grupa Topex are strictly forbidden and may cause civil and legal liability.

GRAFISKÄS DALAS APRAKSTS

DARBA REŽIMA PĀRSLĒDZĒJS

Padruni adapter - 1 tk5.

Transportkohver - 1 tk6.

ETTEVALMISTUS TÖÖKS

LISAKÄEPIDEME PAIGALDAMINE

POSEBNI PROPISI O SIGURNOSTI

• Koristite štitnike sluha za vrijeme rada s čekićem- bušilicom. Ako se izlažete buci, to može dovesti do gubitka sluha.
• Koristite sredstva za zaštitu dišnih putova za vrijeme rada sa čekićem-bušilicom. Osjetljivost na prašinu može dovesti do bolesti dišnog sustava.
  Ako način rada zahtijeva, koristite sustave za odvod prašine.
• Uređaj koristite sa dodatnim drškama koje ste dobili u kompletu. Gubitak kontrole nad uređajem može dovesti do ozljeda djelatnika.

POZOR! Uređaj služi za korištenje u zatvorenom prostoru.