Video 75 Plus EFP - Camera Tripod Sachtler - Free user manual and instructions

Product Type	Professional Video Tripod with Fluid Head
Brand	Sachtler
Model	Video 75 Plus EFP
Bowl Size	75 mm
Load Capacity	12 kg (26.5 lbs)
Weight (Tripod + Head)	Approx. 5.5 kg (12.1 lbs)
Leg Material	Carbon Fiber
Number of Leg Sections	3
Leg Lock Type	Flip Lock
Spreader	Ground Spreader (removable)
Head Type	Fluid Head
Drag System	Continuous fluid drag (pan and tilt)
Counterbalance	Adjustable (0-5 kg)
Quick Release Plate	Sachtler snap-in plate with safety lock
Tilt Range	±90°
Pan Range	360°
Working Height	30 cm to 160 cm (11.8 in to 63 in)
Temperature Range	-40°C to +60°C (-40°F to +140°F)
Power Supply	None (manual operation)
Maintenance	Clean with dry cloth; avoid solvents
Spare Parts Availability	Leg pads, fluid cartridges, plates available
Application	EFP (Electronic Field Production), ENG

Frequently Asked Questions - Video 75 Plus EFP Sachtler

What is the maximum payload of the Sachtler Video 75 Plus EFP?

The maximum payload is 12 kg (26.5 lbs), suitable for professional camcorders and accessories.

How do I adjust the counterbalance?

Use the counterbalance knob on the left side of the head. Turn it to match your camera weight (0-5 kg range) for smooth tilt movement.

What bowl size does this tripod use?

It uses a standard 75 mm bowl, compatible with most Sachtler and third-party heads.

Can I use the tripod with a slider?

Yes, the flat base with 75 mm bowl allows mounting on sliders or flat surfaces using appropriate adapters.

How do I clean the fluid head?

Wipe the exterior with a soft, dry cloth. Avoid abrasive cleaners or submerging in water. For internal service, contact a Sachtler service center.

Are replacement leg pads available?

Yes, Sachtler offers replacement rubber foot pads, part number 2821. They can be ordered from authorized dealers.

What is the lowest working height?

The minimum height is approximately 30 cm (11.8 in) when the legs are fully spread and the center column is retracted.

Does the head have a pan/tilt lock?

Yes, there are individual pan and tilt locks for locking the head in position.

How do I attach the quick release plate?

Slide the plate into the receiver from the rear until it clicks. Press the safety button to release. Ensure the camera plate is tight.

Can I use this tripod in cold weather?

Yes, it is designed for -40°C to +60°C. The fluid head remains smooth in extreme cold, but avoid sudden temperature changes.

USER MANUAL Video 75 Plus EFP Sachtler

Close-up of a black video camera with visible 'VIDEO 75 PLUS' branding and control knobs (no text beyond label)

sachtler

We want you to receive Sachler products that are always state of the art.

Therefore we reserve the right to make changes based on technical advances.

Vitec Group Videocom Division

www.vitecgroup.com

Erfurter Strasse 16 Postfach / P.O.BOX 2039

D-85386 Eching D-85380 Eching

Germany Germany

Telefon: [phone]

Telefax: ([phone]

E-Mail: [e-mail]

Homepage: http://www.sachtler.com

Table of contents

1 Safety instructions ....1
2 Operating elements....1
3 Operation ....2

3.1 Levelling of the fluid head....2
3.2 Removing of the camera plate 2
3.3 Mounting of the camera....2
3.4 Removing of the camera....3
3.5 Positioning of the camera....4
3.6 Adjusting the camera's counterbalance 4
3.7 Setting of the Damping....5
3.8 Brakes 6
3.9 Support for view finder extension and Front Box .....6
3.10 Change of the batteries 6
3.11 Transport setting of damping, counterbalance ...... and brakes ...... 6

1. Technical specifications....7

4.1 General data ....7
4.2 Dimensions 8

5 The modular system ....8

5.1 Conversion of the Video 75 Plus EFP to include V-shaped wedge plate....9
5.2 Conversion of Video 75 Plus EFP to include flat base ..10
5.3 Conversion of the Video 75 Plus EFP to include Mitchell base....10

6 Accessories....11
7 Warranty....12

Inhaltsverzeichnis

EC - Declaration of Conformity

Here we declare that this product complies with the requirements of the applied directives, standards and regulations for safety and health, if used for its intended application.

This declaration becomes invalid, if any changes have been made without our agreement.

Standards and Regulations

EN 55103-1:2006

1 Safety instructions

When the camera is mounted, the clamping screw of the Video 75 Plus EFP must only be released if camera and tripod are secured against falling over.
When placing the camera plate into the Video 75 Plus EFP, make sure not to put fingers within the range of the locking lever, since it will snap back.
When releasing the vertical brake make sure that the camera is secured against any sudden movement.
Do not operate the fluid head upside down without the necessary securing devices, i.e. ropes etc.
Before transport reset fluid damping to "0"

2 Operating elements

3 Operation

3.1 Levelling of the fluid head

The Video 75 Plus EFP has a bubble level.

Apply the vertical brake of the Video 75 Plus EFP and hold the camera with one hand.

Open the clamping screw of the fluid head and move the head in such a way, that the bubble moves into the level's black circle. Tighten the clamping screw firmly.

Touch Bubble level

The Video 75 Plus EFP has a self illuminating touch bubble which allows easy levelling even under unfavourable lighting conditions.

The illumination is activated by strong tapping on the bubble. The bubble will light up to 45 seconds.

3.2 Removing of the camera plate

The Video 75 Plus EFP comes with a Touch & Go® quick release plate.

→Hold the camera plate with one hand.
→Grasp the locking lever with your thumb and index and pull down the red safety button.
→Move the locking lever as far as possible to the left (audible clicking) and take out the camera plate.

3.3 Mounting of the camera

Attach the camera plate to the tripod adapter plate (camera accessory) around the camera's centre of gravity.

→Turn the counterbalance knob to position12

Apply horizontal brake and release vertical brake

Video 75 Plus EFPManual

→The springs of the counterbalance engage automatically by tilting the camera through the horizontal position (audible clicking).
Lock the head with the tilt safety lock.

The blocking and clicking into position of the tilt safety lock is achieved by pulling out the red knob and turning it 90°. The Green marking on the red knob becomes visible. Make sure that the tilt safety lock has engaged (The head can't be tilted any more).

→Put the front of the camera plate in place first.
By fitting the camera onto the head it will lock automatically and the locking lever will snap back audibly into its initial position.

3.4 Removing of the camera

Lock the head with the tilt safety lock.

The blocking and clicking into position of the tilt safety lock is achieved by pulling out the red knob and turning it 90°. The Green marking on the red knob becomes invisible. Make sure that the tilt safety lock has engaged (The head can't be tilted any more).

→Hold the camera with one hand.
→Grasp the locking lever with your thumb and index and pull down the red safety button.
Move the locking lever as far as possible to the left and take out the camera plate.

ManualVideo 75 Plus EFI

3.5 Positioning the camera

→Hold the camera by securing the pan bar.
Apply horizontal brake and release vertical brake and tilt safety lock by pulling out the red knob and turning it 90°. The Green marking on the red knob becomes visible (rocking the pan bars up and down will facilitate this).
→Select 0 on the vertical drag adjustment ring.
→Open the lock of the camera sliding balance plate.

On the Video 75 Plus EFP you have to push the red lever back underneath the balance plate as far as possible.

By turning the spindle forwards and backwards move the camera until you have reached a position where the camera is balanced horizontally. Rear-heavy cameras are moved to the front by turning the spindle clockwise, front-heavy cameras are moved to the back by turning the spindle counter clockwise. This will be easier when the camera is held in a horizontal position.

Secure sliding balance plate with clamping lever (spindle drive is self-locking, clamping serves to eliminate play).
Lock the balance plate on the Video 75 Plus EFP by pulling the red lever into its initial position.

Caution: If you can't manage to center the camera, you should move the camera plate to a different position on the tripod mounting adapter.

3.6 Adjusting the camera's counterbalance

→Hold the camera by securing the pan bar. Turn the counterbalance knob to that number which best compensates for the weight of the camera.
After each spring is released, check if the camera will remain in a tilted position, without moving upwards or downwards significantly.

Video 75 Plus EFPManual

Engaging or disengaging the right lever (small weight symbol) will apply or release half a spring which will help to select optimum counterbalance. When the spring is engaged the lever should be in an upright position, metal pin is not visible - if disengaged the metal pin inside the lever is visible.
With the Boost Button you can shift the range of the counterbalance. Turn on the Boost Button for heavier camerakonfigurations, (big weight symbol).

Please note: A lower counterbalance setting becomes immediately effective in any tilt position. An increase of the counterbalance setting will only be effective in the horizontal position (springs must click in audibly).

3.7 Setting of the Damping

The Video 75 Plus EFP is equipped with nine damping levels horizontally and vertically and a zero setting. By turning the vertical setting and the horizontal setting one selects the desired level of the fluid damping.

Turn the setting ring to "0" in order to switch off the damping completely.

If you set the setting rings on the same index number (e.g. "3") the degree of the horizontal and vertical damping is identical and thus enables precise diagonal panning movements without jerks and vibrations.

Make sure that you always turn the setting to the next indexed position. Engage the retainer pins by slowly panning or tilting the camera.

ManualVideo 75 Plus EFI

ATTENTION:

Panning or tilting the camera with settings between the indexed positions can damage the retainer pins and/or disks.

3.8 Brakes

The horizontal brake applies the lock for the pan and the vertical brake for the tilt movement. Both brakes are vibrationless and can be used during shooting.

3.9 Support for view finder extension and Front Box

The Video 75 plus EFP has on its left side a preparation to accept a support system for a view finder extension.

Drill holes at the front of the fluid head accept a Front Box bracket (e.g. OConnor Front Box).

3.10 Change of the batteries

The illumination is powered by three standard type button cells (625 U or LR9) located in the battery holder, which can be opened with a sharp object such as a screwdriver.

Make sure to insert the new batteries according to the "plus" and "minus" symbols as indicated in the covering plate.

The batteries last for about 2000 illumination cycles.

3.11 Transport setting of damping, counterbalance and brakes

To ensure smooth operation of the setting rings for the damping over the long life time period of the fluid head, you should turn both setting rings from position "0" to maximum position, before and after the use of the fluid head.

Setting during transportation: the most important issue is to open both brakes - horizontal and vertical.

Counterbalance and damping should be set to maximum position.

4 Technical Specifications

4.1 General Data

Counterbalance:	24 steps + Boost Button
Balance plate:	120 mm sliding range
Grades of damping:	horizontal and vertical 9 each and 0
Tilt angle:	+90° / -60°
Pan range:	360°
Temperature range:	-40°C to 60°C
Weight:	12 kg
Maximum load:	11.9 - 69.6 kg @ 200 mm cog14.4 - 84.1 kg @ 150 mm cog(Expandable to 84,1 kg @150 mm cog)
Camera fitting:	Touch & Go® with camera plate 35
tripod / pedestal fitting:	150 mm ball with integrated flatbody-fitting
Pan arms:	Two telescopic pan bars with attachment diameter: 28 mm / 1.1" (front), 32 mm / 1.3" (back) and 40 mm / 1.6" at pan bar end. Adjustable length of 450 - 730 mm / 17.7" - 28.7"
Batteries:	3 each 625 U or LR9

ManualVideo 75 Plus EFI

4.2 Dimensions

5 The modular system

Due to the Video 75 Plus EFP fluid heads modular design you may perform certain modifications yourself. In order to safe time you can do all work with an Allen wrench #4 unless otherwise specified.

The following modifications can be performed:

Conversion of the Video 75 Plus EFP to include V-shaped wedge plate
Conversion of Video 75 Plus EFP to include flat base
Conversion of the Video 75 Plus EFP to include Mitchell

sachtler

Manual

Video 75 Plus EFP

5.1 Conversion of the Video 75 Plus EFP to include V-shaped wedge plate

Open the 2 screws of the spindle fixation with Allen wrench # 2 and remove the fixation piece.

Open the lock of the balance plate by pushing back the red lever underneath the balance plate as far as possible.

Keep on turning the knob of the spindle to the left until you can remove the balance plate.

Loosen the 4 screws (now visible) of the base plate underneath and remove it.

Get the Studio set up from the Sachler accessory range.

With this set up it is likely that you have to remove the balance plate from the base plate first. Therefore you have to remove the fixation screw in the spindles top end. Open the lock of the balance plate and keep on turning the knob of the spindle to the left until you can remove the balance plate.

Screw the base plate onto the head. Fasten the allen screws hand-tight.

Guide the balance plate with spindle into the base plate.

Turn the spindle to the right until you can see it coming out at the front of the head.

Place the fixation screw in the spindles top end and tighten it. The spindle is now fastened. The conversion is done.

5.2 Conversion of Video 75 Plus EFP to include flat base

Put the Video 75 Plus EFP upside down, so that you can access the bottom of the head.

Next to the centre bolt you will see 4 allen screws. Those have to be unscrewed and the whole piece has to be removed.

Now the Video 75 Plus EFP can be mounted onto flat base tripods and pedestals with 4 bolt flat base directly. For Quickfix mount and all Sachtler pedestals the Multi Disc from the Sachtler accessory range is required.

It is mounted onto the fluid heads 4 bolt flat base.

5.3 Conversion of the Video 75 Plus EFP to include Mitchell base

Especially in the United States the Mitchell mount is Common.

For conversion turn the fluid head upside down, so you can access the bottom of the head.

Next to the centre bolt you will see 4 allen screws. Those have to be unscrewed and the whole piece has to be removed.

Take the Mitchell adapter piece with locking knob from the Sachtler accessory range.

Place the adapter piece into the recess at the bottom side of the head.

Fasten the 4 allen screws hand-tight.

The fluid head is tightened onto the tripod via the Mitchell locking knob

6 Accessories

Recommended parts from the Sachtler accessory range:

	Description: Code Nr.: Notice:
	Studioaufbau 7550 V-shaped wedge plate
	Multi Disc 3914 in combination with Quickfix und Sachter pedestals
	Mitchell adapter piece 6053 for Video 75 Plus EFP, with locking knob Video 75 Plus Studio
	Cable clamp V 75 6055
	Front pan bar 3172
	Case V/C 75 9517

ManualVideo 75 Plus EFI

7 Warranty

Warranty expires if:

The fluid head was operated improperly or not in line with the specified technical data, or
the head housing was opened by unauthorised personnel.
We reserve the right to make changes based on technical advances.

Please register at www.sachtler.com for an extended warranty period.

Vitec Brazil Technologies Ltda

Rua Quintana, 950 - cj.32

Brooklin

Sâu Paulo, 04569-011

Brazi

Tel: [phone]

Fax: [phone]

JAPAN

Sachtler Japan

P.A. Building 4F

3-12-6 Aobadai

Meguro-ku

Tokyo 153-0042

Japan

Tel: [phone]

Fax: [phone]

CHINA

Vitec China

Rm 706, Tower B

Derun Building

YongAn Dongli A No.8

Jianwai Ave., Chaoyang District

100022 Beijing

China

Tel: [phone]

Fax: [phone]

SINGAPORE

Vitec Videocom Pte Ltd.

6 New Industrial Road

02-02 Hoe Huat Industrial Building

Singapore 536199

Tel: +65 629 7

Fax: [phone]

FRANCE

Vitec Videocom

William Vinten Building

Western Way

Bury St. Edmunds

Suffolk IP33 3TB

UK

Tel: [phone]

Fax: [phone]

Sales Fax: [phone]

GERMANY

Vitec Videocom GmbH

Headquarters

Erfurter Strasse 16

85386 Eching

Germany

Tel: [phone]

Fax: [phone]

USA

Vitec Videocom Inc.

709 Executive Blvd.

Valley Cott

New York 10989

USA

Tel: [phone]

for more information, visit

www.sachtler.com