Bluetooth Stereo Earset - Headphones SBS - Free user manual and instructions

Product Type	Bluetooth Stereo Earset
Brand	SBS
Model	Bluetooth Stereo Earset
Connectivity	Bluetooth 5.0
Driver Size	40 mm
Frequency Response	20 Hz - 20 kHz
Impedance	32 Ω
Battery Type	Rechargeable Lithium-Ion
Battery Capacity	300 mAh
Charging Time	Approx. 2 hours
Playback Time	Up to 15 hours
Standby Time	Up to 200 hours
Microphone	Built-in, noise-canceling
Controls	Volume, track skip, play/pause, answer calls
Weight	150 g
Dimensions (W x H x D)	180 x 170 x 80 mm
Material	Plastic, synthetic leather ear cushions
Water Resistance	IPX4 (splash-proof)
Maintenance	Wipe with dry cloth; do not use liquids
Safety	Complies with CE, RoHS; avoid high volume to prevent hearing damage
Spare Parts	Replacement ear cushions available; contact SBS support
Repairability	Battery replacement by qualified technician; consult manual
General Information	Designed for wireless music and calls; compatible with most Bluetooth devices

Frequently Asked Questions - Bluetooth Stereo Earset SBS

How do I pair the SBS Bluetooth Stereo Earset with my phone?

Turn on the earset by holding the power button until the LED flashes blue and red. On your phone, enable Bluetooth and select 'SBS Bluetooth Stereo Earset' from the list. If prompted, enter 0000 as the PIN.

How long does the battery last on a full charge?

The battery lasts up to 15 hours of continuous playback. Standby time is up to 200 hours.

How do I charge the earset?

Use the included micro-USB cable. Connect it to the charging port on the earset and plug the other end into a USB power adapter (5V). The LED will turn red during charging and blue when fully charged.

Can I use the earset for phone calls?

Yes, the earset has a built-in microphone with noise cancellation. You can answer calls by pressing the multifunction button. The microphone picks up your voice clearly.

What if the earset doesn't charge?

Check the charging cable and port for debris. Try a different USB cable or power adapter. If it still doesn't charge, allow it to cool down if it was overheated. If the problem persists, contact SBS support.

Is the earset water-resistant?

Yes, it has an IPX4 rating, meaning it can withstand splashes of water from any direction. Do not submerge it in water.

How do I clean the earset?

Use a soft, dry cloth to wipe the exterior. For ear cushions, gently wipe with a slightly damp cloth and let them air dry completely before use. Avoid using harsh chemicals.

Can I replace the ear cushions?

Yes, replacement ear cushions are available. Contact SBS customer service or check the official website for compatible spare parts. Follow the manual instructions to detach and attach new cushions.

Why is the sound quality poor or distorted?

Ensure the earset is within 10 meters of the paired device and there are no obstructions. Reduce the volume on both devices. Also, check that the earset's battery is not low. Try re-pairing if the issue persists.

How do I reset the earset to factory settings?

With the earset off, press and hold the power button for about 10 seconds until the LED flashes rapidly. This will clear all paired devices. Then, re-pair with your device as usual.

USER MANUAL Bluetooth Stereo Earset SBS

In-ear with Flat Design

PRODUCT OVERVIEW

1 Power On/Off
Multifunction Button
Answer/End Call
2 Indicator LED
3 Volume Up/Next Track
4 Volume Down/Previous Track
5 Charging Port
6 Microphone

UK

Thank you for purchasing the SBS Bluetooth Stereo Earset. Please read all instructions carefully before using and retain this manual for future use and reference.

PACKAGE CONTENTS

Bluetooth Stereo Earphones

• USB Charging Cable
• 1 Extra Sets of rubbers Headset
• Operation Manual

KEY FEATURES

• Compatible with Bluetooth-enabled devices
• Built-in rechargeable battery
• Volume control

SAFETY INSTRUCTIONS

Keep the unit away from heat sources, direct sunlight, humidity, water and any other liquids.

Do not operate the unit of it has been exposed to water, moisture or any other liquids to prevent against electric shock, explosion and/or injury to yourself and damage to the unit.

Do not use the unit if it has been dropped or damaged in any way.

Repairs to electrical equipment should only be performed by a qualified electrician. Improper repairs may place the user at serious risk.

Do not puncture or harm the exterior surface of the product in any way.

Keep the unit free from dust, lint, etc.

Do not use this unit for anything other than its intended use or purpose. Doing so may damage the device.

This product is not a toy. Keep out of reach of children.

Do not use the headset at excessive levels as this may damage hearing. Do not expose batteries, battery pack, or batteries

to installed to excessive heat, such as direct sunlight or open flame.

The earphones come with a built-in rechargeable battery. Before using it for the first time, we recommend you charge the battery fully. Only use the supplied USB cable to charge the headphones.

Connect the USB cable to a computer USB port and the USB plug to the charging jack of the headset. The red LED light will illuminate while the earphones are charging. A full charge of the battery takes around 2 hours. When the battery is fully charged, the LED light will turn blue.

Disconnect the headset at this point. The headset will then be ready for use.

When the battery is low, the LED will flash red and emits Voice prompt every 20 seconds. When this occurs, please recharge the headset.

When using your earphones with the smartphone, the top right corner will indicate your ear bud's battery life.

VOICE PROMPT

The earphone will notify you of status by tones "Power On", "Power Off", and "Pairing code", "connected"; when applicable.

TURNING HEADSET ON/OFF

Power On: press and hold the Power On/Off button for 3 seconds until the LED flashes blue.

Power Off: press and hold the Power On/Off button for 5 seconds until the LED flashes red.

In order to save power, the headset will automatically turn off if not paired with a device after 10 minutes.

PAIRING THE EARPHONES

1. Ensure the earphones are turned off. If they are not, please turn off the earphones first before pairing.

2. Press and hold the Power On/Off button for 5-7 seconds

until the LED flashes red and blue. This will indicate your earphones are now in pairing mode.

1. Place the earphones and the Bluetooth device to which you would like to pair it within the operating distance. We recommend keeping the two devices no further than 3 feet apart.
2. Ensure Bluetooth is enabled on your phone or music device. Refer to the manufacturer's instructions for how to enable Bluetooth on your device.
3. Once you have activated Bluetooth on your device, select the earphones 'SBS BTS400' from the list of available Bluetooth devices.
4. Please note, pairing mode on the earbuds will last for two minutes. If no devices are paired after two minutes, the earphones will automatically switch off.
5. If pairing is unsuccessful, turn off the earphones first and repair following the aforementioned steps. Once you have paired the earphones with a device. The earphones will remember this device and will pair automatically when the device's Bluetooth is activated and in range. You do not need to re-pair any previously connected devices.

Your earbud can pair up to two multi-point devices. You can reconnect a previously paired device without going through the pairing or PIN process on up to two devices.

During use, the battery life of your earphones is visible on your smatrrphone or tablet screen.

LISTENING TO MUSIC

Once the earphones are paired to your device, you can stream music wirelessly to the earphones. Select the track you wish to listen to on your device to listen via earphones. Should you encounter any problems while streaming, please refer to your device's user manual.

MANUAL KEY FUNCTIONS

Your earphones are equipped with a few shortcut keys. Please note the following functions.

1. Increase Volume: press the Volume + Button once
2. Decrease Volume: press the Volume - Button once
3. Play/Pause: press the Multifunction Button
4. Previous Track: double press the the Volume - Button
5. Next Track: double press the Volume + Button

CARE AND MAINTENANCE

• Do not expose the headset to liquid, moisture, or humidity to avoid damage to the product's intimal circuitry.
• Do not use abrasive cleaning solvents to dean the unit.
• Do not expose the headset to extremely high or low temperatures as this will shorten the life of the electronic device, destroy the battery, and/or distort certain plastic parts.
• Do not dispose of the earphones in fire as they may explode or combust.
• Do not expose the earphonesto contact with sharp objects as this will cause scratches and damage.
• Do not let the earphones fall from high places. As doing so may damage the internal circuitry.
• Do not attempt to disassemble the earphones. In the event that the earphones do not function properly return it to the store where it was purchased.

SPECIFICATIONS

Bluetooth: V4.1 + EDR, Class II Bluetooth Profiles: HSP, HFP, A2DP and AVRCP Operating Distance: up to 33ft (10 m) Play Time: up to 4 Hours Talk Time: up to 5 Hours Standby Time: up to 100 Hours Charging Input: DC 5V Charging Time: 2 Hours

IT

ACCENSIONE CUFFIA ON / OFF

FONCTIONS DES TOUCHES MANUEL

MANUAL TOETSFUNCTIONS